187 lines
8.0 KiB
Markdown
187 lines
8.0 KiB
Markdown
# ESP32-C3 BSP Introduction
|
||
|
||
[中文](README_ZH.md) | English
|
||
|
||
This document records the execution instruction of the BSP (board support package) for the [ESP32-C3](http://luatos.com/t/esp32c3) development board.
|
||
|
||
The document is covered in two parts:
|
||
|
||
- Board Resources Introduction
|
||
- Quickly Get Started
|
||
|
||
## Resources Introduction
|
||
|
||
We tested 2 development boards, it all works, but due to the different LED pins of the two development boards, so we'll need to select the corresponding development board in the menuconfig.
|
||
|
||
- [LUATOS_ESP32C3](https://wiki.luatos.com/chips/esp32c3/board.html)
|
||
|
||
|
||
|
||
- [HX-DK-商](https://docs.wireless-tech.cn/doc/7/)
|
||
|
||
|
||
|
||
The mainly-used resources of LUATOS_ESP32C3 are shown as follows:
|
||
|
||
- MCU: [esp32-c3](https://www.espressif.com/sites/default/files/documentation/esp32-c3_datasheet_en.pdf)，Main Frequency 160MHz, 407.22 CoreMark; 2.55 CoreMark/MHz
|
||
- Built-in Chip: 384KB ROM, 400KB SRAM
|
||
- Peripherals
|
||
- Red LED: 2, LED: D4 (IO12), D5（IO13）
|
||
- Button: 2, K1（BOOT） K2(RST)
|
||
- SPI FLASH: 4M
|
||
- Common-used interfaces: USB, UART, etc.
|
||
|
||
### For more details about this board, please refer to [Here](https://wiki.luatos.com/chips/esp32c3/board.html).
|
||
|
||
## **Peripheral Condition**
|
||
|
||
Each peripheral supporting condition for this BSP is as follows:
|
||
|
||
| **On-board Peripherals** | ****Support**** | ****Remark**** |
|
||
| ------------------------ | --------------- | ------------------------------------------------------------ |
|
||
| GPIO | Support | |
|
||
| UART | Support | Using LUATOS_ESP32C3 development board requires connecting serial port to USB chip UART0_TX and UART0_RX (such as CP2102) |
|
||
| JTAG debug | Support | ESP32C3 usb-linked development boards can be debugged |
|
||
| WIFI | Partial support | There are currently some problems, such as `rt_mq_recive` cannot be used in ISR, etc. |
|
||
| BLE | Partially supported | There are currently some problems, such as `NimBLE` running errors after starting for a while |
|
||
| GDBStub | Support | You can use the GDB provided by ESP-IDF by turning on the `BSP_ENABLE_GDBSTUB` switch, which will enter GDB mode after a chip error |
|
||
| HWTIMER | Support |
|
||
Note:
|
||
|
||
1. WIFI and BLE cannot be enabled at the same time. When using the BLE driver, be sure to turn off the `RT_USING_WIFI` and `LWIP` switches in `menuconfig`. In addition, due to limited capabilities and lack of debugging equipment, there are problems with WIFI and BLE driver operation. If it can be solved, please contact [timwcx@qq.com](mailto:timwcx@qq.com).
|
||
|
||
2. The BLE driver only supports `NimBLE` and is provided by the `bluetooth` component in `esp-idf`. To use the BLE driver, please refer to `bsp/ESP32_C3/packages/ESP-IDF-latest/examples/bluetooth/nimble` Sample program, please note that the `esp_timer_init()` function must be called to initialize the clock driver before calling the `NimBLE` related interface.
|
||
|
||
One way to run the BLE sample is to add the sample program to `scons` compilation and call the clock initialization program and sample program entry in `bsp/ESP32_C3/main/main.c`.
|
||
|
||
```c
|
||
int main(void) {
|
||
...
|
||
#ifdef BSP_USING_BLE
|
||
esp_timer_init(); //Call clock initialization program
|
||
app_main(); //Call the BLE sample program entry
|
||
#endif
|
||
...
|
||
}
|
||
```
|
||
|
||
3、 Regarding the use of the GDBStub component, please see [ESP-IDF official documentation on GDBStub](https://docs.espressif.com/projects/esp-idf/zh_CN/latest/esp32c3/api-guides/tools/idf- monitor.html?#gdbstub-gdb), currently I have provided a debugging script `esp32c3.gdb`, the specific usage method is as follows.
|
||
|
||
```sh
|
||
wcx@tim ~/rt-thread/bsp/ESP32_C3 esp32 ± sudo riscv32-esp-elf-gdb # Enter gdb debugging
|
||
GNU gdb (crosstool-NG esp-2022r1-RC1) 9.2.90.20200913-git
|
||
Copyright (C) 2020 Free Software Foundation, Inc.
|
||
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
|
||
This is free software: you are free to change and redistribute it.
|
||
There is NO WARRANTY, to the extent permitted by law.
|
||
Type "show copying" and "show warranty" for details.
|
||
This GDB was configured as "--host=x86_64-build_pc-linux-gnu --target=riscv32-esp-elf".
|
||
Type "show configuration" for configuration details.
|
||
For bug reporting instructions, please see:
|
||
<http://www.gnu.org/software/gdb/bugs/>.
|
||
Find the GDB manual and other documentation resources online at:
|
||
<http://www.gnu.org/software/gdb/documentation/>.
|
||
|
||
For help, type "help".
|
||
Type "apropos word" to search for commands related to "word".
|
||
(gdb) source esp32c3.gpb # Load gdb script
|
||
0x3fca8c30 in __stack_start__ ()
|
||
(gdb)
|
||
```
|
||
|
||
## Environment construction and compilation
|
||
|
||
1. Download the RISC-V toolchain:
|
||
|
||
```sh
|
||
wget https://github.com/espressif/crosstool-NG/releases/download/esp-2022r1-RC1/riscv32-esp-elf-gcc11_2_0-esp-2022r1-RC1-linux-amd64.tar.xz
|
||
tar xf riscv32-esp-elf-gcc11_2_0-esp-2022r1-RC1-linux-amd64.tar.xz
|
||
```
|
||
|
||
2. Configure the path of the toolchain:
|
||
|
||
Add the local path of the `RISC-V` toolchain to the `EXEC_PATH` variable in the `rtconfig.py` file, or specify the path by setting the `RTT_EXEC_PATH` environment variable, for example:
|
||
|
||
```sh
|
||
export RTT_EXEC_PATH=/opt/riscv32-esp-elf/bin
|
||
```
|
||
|
||
3. Compile
|
||
|
||
Install esptool to convert ELF files to binary flash files:
|
||
|
||
```sh
|
||
pip install esptool
|
||
```
|
||
|
||
Execute the following command on the Linux platform to configure:
|
||
|
||
```
|
||
scons --menuconfig
|
||
```
|
||
|
||
It will automatically download env-related scripts to the `~/.env` directory, and then execute:
|
||
|
||
```sh
|
||
source ~/.env/env.sh
|
||
|
||
cd bsp/ESP32_C3/
|
||
pkgs --update
|
||
```
|
||
|
||
It will automatically download `RT-Thread-packages/esp-idf` and `RT-Thread-packages/FreeRTOS-Wrapper`, after updating the software packages, execute `scons` to compile the board support package.
|
||
|
||
If the compilation is successful, `rtthread.elf`, `rtthread.bin` files will be generated.
|
||
|
||
## Download and program
|
||
|
||
In Windows, we can use *flash* supported by ESPRESSIF.
|
||
|
||
In Linux, we can use the esptool, which we have downloaded serval steps
|
||
|
||
### Windows
|
||
|
||
1. Programming tool download
|
||
|
||
The current bsp test uses the [Flash Download Tools](https://www.espressif.com.cn/sites/default/files/tools/flash_download_tool_3.9.4_0.zip) tool to program without errors.
|
||
|
||
2. Programming tool configuration
|
||
|
||
Chip model selection `ESP32-C3`
|
||
|
||
Configure the binary file and offset address as follows:
|
||
|
||
| binary file | offset address |
|
||
| ------------------- | -------- |
|
||
| bootloader.bin | 0x0 |
|
||
| partition-table.bin | 0x8000 |
|
||
| rtthread.bin | 0x10000 |
|
||
|
||
Among them, `bootloader.bin` and `partition-table.bin` can be found in the `bsp/ESP32_C3/builtin_imgs` folder. After the configuration is completed, the screenshot is as follows, and then click `START` to download.
|
||
|
||
|
||
|
||
### Linux
|
||
|
||
```sh
|
||
esptool.py -b 115200 --before default_reset --after hard_reset write_flash --flash_mode dio --flash_size detect --flash_freq 80m 0x0 path/to/your/bootloader.bin 0x08000 path/to/your/partition-table.bin 0x010000 path/to/your/rtthread.bin
|
||
```
|
||
if you have more than one ESP device connected, you can use -p to choose which device to use.
|
||
|
||
if the command failed, check whether user ave enough privilige to access the serials.
|
||
|
||
or we can check ESPRESSIF's [Troubleshooting](https://docs.espressif.com/projects/esptool/en/latest/esp32/troubleshooting.html) to get more help.
|
||
|
||
## Notes
|
||
|
||
- The basic functions are now supported, but it needs more, welcome any contributions and feedback.
|
||
|
||
|
||
Maintainer:
|
||
|
||
- [supperthomas](https://github.com/supperthomas) email address: [78900636@qq.com](mailto:78900636@qq.com)
|
||
- [tangzz98](https://github.com/tangzz98) email address: [tangz98@outlook.com](tangz98@outlook.com)
|
||
|
||
Special thanks to [chenyingchun0312](https://github.com/chenyingchun0312) for providing support on the RISC-V part working.
|
||
|