255 lines
12 KiB
C
255 lines
12 KiB
C
/*
|
|
* Copyright 2017-2018 NXP
|
|
* All rights reserved.
|
|
*
|
|
* SPDX-License-Identifier: BSD-3-Clause
|
|
*/
|
|
|
|
#ifndef _BOARD_H_
|
|
#define _BOARD_H_
|
|
|
|
#include "clock_config.h"
|
|
#include "fsl_common.h"
|
|
#include "fsl_gpio.h"
|
|
#include "fsl_clock.h"
|
|
|
|
/*******************************************************************************
|
|
* Definitions
|
|
******************************************************************************/
|
|
/*! @brief The board name */
|
|
#define BOARD_NAME "IMXRT1050-EVKB"
|
|
|
|
/* The UART to use for debug messages. */
|
|
#define BOARD_DEBUG_UART_TYPE kSerialPort_Uart
|
|
#define BOARD_DEBUG_UART_BASEADDR (uint32_t) LPUART1
|
|
#define BOARD_DEBUG_UART_INSTANCE 1U
|
|
|
|
#define BOARD_DEBUG_UART_CLK_FREQ BOARD_DebugConsoleSrcFreq()
|
|
|
|
#define BOARD_UART_IRQ LPUART1_IRQn
|
|
#define BOARD_UART_IRQ_HANDLER LPUART1_IRQHandler
|
|
|
|
#ifndef BOARD_DEBUG_UART_BAUDRATE
|
|
#define BOARD_DEBUG_UART_BAUDRATE (115200U)
|
|
#endif /* BOARD_DEBUG_UART_BAUDRATE */
|
|
|
|
/*! @brief The USER_LED used for board */
|
|
#define LOGIC_LED_ON (0U)
|
|
#define LOGIC_LED_OFF (1U)
|
|
#ifndef BOARD_USER_LED_GPIO
|
|
#define BOARD_USER_LED_GPIO GPIO1
|
|
#endif
|
|
#ifndef BOARD_USER_LED_GPIO_PIN
|
|
#define BOARD_USER_LED_GPIO_PIN (9U)
|
|
#endif
|
|
|
|
#define USER_LED_INIT(output) \
|
|
GPIO_PinWrite(BOARD_USER_LED_GPIO, BOARD_USER_LED_GPIO_PIN, output); \
|
|
BOARD_USER_LED_GPIO->GDIR |= (1U << BOARD_USER_LED_GPIO_PIN) /*!< Enable target USER_LED */
|
|
#define USER_LED_ON() \
|
|
GPIO_PortClear(BOARD_USER_LED_GPIO, 1U << BOARD_USER_LED_GPIO_PIN) /*!< Turn off target USER_LED */
|
|
#define USER_LED_OFF() GPIO_PortSet(BOARD_USER_LED_GPIO, 1U << BOARD_USER_LED_GPIO_PIN) /*!<Turn on target USER_LED*/
|
|
#define USER_LED_TOGGLE() \
|
|
GPIO_PinWrite(BOARD_USER_LED_GPIO, BOARD_USER_LED_GPIO_PIN, \
|
|
0x1 ^ GPIO_PinRead(BOARD_USER_LED_GPIO, BOARD_USER_LED_GPIO_PIN)) /*!< Toggle target USER_LED */
|
|
|
|
/*! @brief Define the port interrupt number for the board switches */
|
|
#ifndef BOARD_USER_BUTTON_GPIO
|
|
#define BOARD_USER_BUTTON_GPIO GPIO5
|
|
#endif
|
|
#ifndef BOARD_USER_BUTTON_GPIO_PIN
|
|
#define BOARD_USER_BUTTON_GPIO_PIN (0U)
|
|
#endif
|
|
#define BOARD_USER_BUTTON_IRQ GPIO5_Combined_0_15_IRQn
|
|
#define BOARD_USER_BUTTON_IRQ_HANDLER GPIO5_Combined_0_15_IRQHandler
|
|
#define BOARD_USER_BUTTON_NAME "SW8"
|
|
|
|
/*! @brief The hyper flash size */
|
|
#define BOARD_FLASH_SIZE (0x4000000U)
|
|
|
|
/*! @brief The ENET PHY address. */
|
|
#define BOARD_ENET0_PHY_ADDRESS (0x02U) /* Phy address of enet port 0. */
|
|
|
|
/* USB PHY condfiguration */
|
|
#define BOARD_USB_PHY_D_CAL (0x0CU)
|
|
#define BOARD_USB_PHY_TXCAL45DP (0x06U)
|
|
#define BOARD_USB_PHY_TXCAL45DM (0x06U)
|
|
|
|
#define BOARD_ARDUINO_INT_IRQ (GPIO1_INT3_IRQn)
|
|
#define BOARD_ARDUINO_I2C_IRQ (LPI2C1_IRQn)
|
|
#define BOARD_ARDUINO_I2C_INDEX (1)
|
|
#define BOARD_USDHC1_BASEADDR USDHC1
|
|
#define BOARD_USDHC2_BASEADDR USDHC2
|
|
#define BOARD_USDHC_CD_GPIO_BASE GPIO2
|
|
#define BOARD_USDHC_CD_GPIO_PIN 28
|
|
#define BOARD_USDHC_CD_PORT_IRQ GPIO2_Combined_16_31_IRQn
|
|
#define BOARD_USDHC_CD_PORT_IRQ_HANDLER GPIO2_Combined_16_31_IRQHandler
|
|
|
|
#define BOARD_USDHC_CD_STATUS() (GPIO_PinRead(BOARD_USDHC_CD_GPIO_BASE, BOARD_USDHC_CD_GPIO_PIN))
|
|
|
|
#define BOARD_USDHC_CD_INTERRUPT_STATUS() (GPIO_PortGetInterruptFlags(BOARD_USDHC_CD_GPIO_BASE))
|
|
#define BOARD_USDHC_CD_CLEAR_INTERRUPT(flag) (GPIO_PortClearInterruptFlags(BOARD_USDHC_CD_GPIO_BASE, flag))
|
|
|
|
#define BOARD_USDHC_CD_GPIO_INIT() \
|
|
{ \
|
|
gpio_pin_config_t sw_config = { \
|
|
kGPIO_DigitalInput, 0, kGPIO_IntRisingOrFallingEdge, \
|
|
}; \
|
|
GPIO_PinInit(BOARD_USDHC_CD_GPIO_BASE, BOARD_USDHC_CD_GPIO_PIN, &sw_config); \
|
|
GPIO_PortEnableInterrupts(BOARD_USDHC_CD_GPIO_BASE, 1U << BOARD_USDHC_CD_GPIO_PIN); \
|
|
GPIO_PortClearInterruptFlags(BOARD_USDHC_CD_GPIO_BASE, ~0); \
|
|
}
|
|
#define BOARD_HAS_SDCARD (1U)
|
|
#define BOARD_SD_POWER_RESET_GPIO (GPIO1)
|
|
#define BOARD_SD_POWER_RESET_GPIO_PIN (5U)
|
|
|
|
#define BOARD_USDHC_CARD_INSERT_CD_LEVEL (0U)
|
|
|
|
#define BOARD_USDHC_MMCCARD_POWER_CONTROL(state)
|
|
|
|
#define BOARD_USDHC_MMCCARD_POWER_CONTROL_INIT() \
|
|
{ \
|
|
gpio_pin_config_t sw_config = { \
|
|
kGPIO_DigitalOutput, 0, kGPIO_NoIntmode, \
|
|
}; \
|
|
GPIO_PinInit(BOARD_SD_POWER_RESET_GPIO, BOARD_SD_POWER_RESET_GPIO_PIN, &sw_config); \
|
|
GPIO_PinWrite(BOARD_SD_POWER_RESET_GPIO, BOARD_SD_POWER_RESET_GPIO_PIN, true); \
|
|
}
|
|
|
|
#define BOARD_USDHC_SDCARD_POWER_CONTROL_INIT() \
|
|
{ \
|
|
gpio_pin_config_t sw_config = { \
|
|
kGPIO_DigitalOutput, 0, kGPIO_NoIntmode, \
|
|
}; \
|
|
GPIO_PinInit(BOARD_SD_POWER_RESET_GPIO, BOARD_SD_POWER_RESET_GPIO_PIN, &sw_config); \
|
|
}
|
|
|
|
#define BOARD_USDHC_SDCARD_POWER_CONTROL(state) \
|
|
(GPIO_PinWrite(BOARD_SD_POWER_RESET_GPIO, BOARD_SD_POWER_RESET_GPIO_PIN, state))
|
|
|
|
#define BOARD_USDHC1_CLK_FREQ (CLOCK_GetSysPfdFreq(kCLOCK_Pfd2) / (CLOCK_GetDiv(kCLOCK_Usdhc1Div) + 1U))
|
|
#define BOARD_USDHC2_CLK_FREQ (CLOCK_GetSysPfdFreq(kCLOCK_Pfd2) / (CLOCK_GetDiv(kCLOCK_Usdhc2Div) + 1U))
|
|
|
|
#define BOARD_SD_HOST_BASEADDR BOARD_USDHC1_BASEADDR
|
|
#define BOARD_SD_HOST_CLK_FREQ BOARD_USDHC1_CLK_FREQ
|
|
#define BOARD_SD_HOST_IRQ USDHC1_IRQn
|
|
|
|
#define BOARD_MMC_HOST_BASEADDR BOARD_USDHC2_BASEADDR
|
|
#define BOARD_MMC_HOST_CLK_FREQ BOARD_USDHC2_CLK_FREQ
|
|
#define BOARD_MMC_HOST_IRQ USDHC2_IRQn
|
|
#define BOARD_MMC_VCCQ_SUPPLY kMMC_VoltageWindow170to195
|
|
#define BOARD_MMC_VCC_SUPPLY kMMC_VoltageWindows270to360
|
|
/* we are using the BB SD socket to DEMO the MMC example,but the
|
|
* SD socket provide 4bit bus only, so we define this macro to avoid
|
|
* 8bit data bus test
|
|
*/
|
|
#define BOARD_MMC_SUPPORT_8BIT_BUS (1U)
|
|
|
|
#define BOARD_SD_HOST_SUPPORT_SDR104_FREQ (200000000U)
|
|
#define BOARD_SD_HOST_SUPPORT_HS200_FREQ (180000000U)
|
|
|
|
/*! @brief The WIFI-QCA shield pin. */
|
|
#define BOARD_INITGT202SHIELD_PWRON_GPIO GPIO1 /*!< GPIO device name: GPIO */
|
|
#define BOARD_INITGT202SHIELD_PWRON_PORT 1U /*!< PORT device index: 1 */
|
|
#define BOARD_INITGT202SHIELD_PWRON_GPIO_PIN 3U /*!< PIO4 pin index: 3 */
|
|
#define BOARD_INITGT202SHIELD_PWRON_PIN_NAME GPIO1_3 /*!< Pin name */
|
|
#define BOARD_INITGT202SHIELD_PWRON_LABEL "PWRON" /*!< Label */
|
|
#define BOARD_INITGT202SHIELD_PWRON_NAME "PWRON" /*!< Identifier name */
|
|
#define BOARD_INITGT202SHIELD_PWRON_DIRECTION kGPIO_DigitalOutput /*!< Direction */
|
|
|
|
#define BOARD_INITGT202SHIELD_IRQ_GPIO GPIO1 /*!< GPIO device name: GPIO */
|
|
#define BOARD_INITGT202SHIELD_IRQ_PORT 1U /*!< PORT device index: 1 */
|
|
#define BOARD_INITGT202SHIELD_IRQ_GPIO_PIN 19U /*!< PIO1 pin index: 19 */
|
|
#define BOARD_INITGT202SHIELD_IRQ_PIN_NAME GPIO1_19 /*!< Pin name */
|
|
#define BOARD_INITGT202SHIELD_IRQ_LABEL "IRQ" /*!< Label */
|
|
#define BOARD_INITGT202SHIELD_IRQ_NAME "IRQ" /*!< Identifier name */
|
|
#define BOARD_INITGT202SHIELD_IRQ_DIRECTION kGPIO_DigitalInput /*!< Direction */
|
|
|
|
/* @Brief Board accelerator sensor configuration */
|
|
#define BOARD_ACCEL_I2C_BASEADDR LPI2C1
|
|
/* Select USB1 PLL (480 MHz) as LPI2C's clock source */
|
|
#define BOARD_ACCEL_I2C_CLOCK_SOURCE_SELECT (0U)
|
|
/* Clock divider for LPI2C clock source */
|
|
#define BOARD_ACCEL_I2C_CLOCK_SOURCE_DIVIDER (5U)
|
|
#define BOARD_ACCEL_I2C_CLOCK_FREQ (CLOCK_GetFreq(kCLOCK_Usb1PllClk) / 8 / (BOARD_ACCEL_I2C_CLOCK_SOURCE_DIVIDER + 1U))
|
|
|
|
#define BOARD_CODEC_I2C_BASEADDR LPI2C1
|
|
#define BOARD_CODEC_I2C_CLOCK_SOURCE_SELECT (0U)
|
|
#define BOARD_CODEC_I2C_CLOCK_SOURCE_DIVIDER (5U)
|
|
#define BOARD_CODEC_I2C_CLOCK_FREQ \
|
|
((CLOCK_GetFreq(kCLOCK_Usb1PllClk) / 8) / (BOARD_CODEC_I2C_CLOCK_SOURCE_DIVIDER + 1U))
|
|
|
|
/* @Brief Board CAMERA configuration */
|
|
#define BOARD_CAMERA_I2C_BASEADDR LPI2C1
|
|
#define BOARD_CAMERA_I2C_CLOCK_SOURCE_DIVIDER (5U)
|
|
#define BOARD_CAMERA_I2C_CLOCK_SOURCE_SELECT (0U) /* Select USB1 PLL (480 MHz) as LPI2C's clock source */
|
|
#define BOARD_CAMERA_I2C_CLOCK_FREQ \
|
|
(CLOCK_GetFreq(kCLOCK_Usb1PllClk) / 8 / (BOARD_CAMERA_I2C_CLOCK_SOURCE_DIVIDER + 1U))
|
|
|
|
#if defined(__cplusplus)
|
|
extern "C" {
|
|
#endif /* __cplusplus */
|
|
|
|
/*******************************************************************************
|
|
* API
|
|
******************************************************************************/
|
|
uint32_t BOARD_DebugConsoleSrcFreq(void);
|
|
|
|
void BOARD_InitDebugConsole(void);
|
|
|
|
void BOARD_ConfigMPU(void);
|
|
#if defined(SDK_I2C_BASED_COMPONENT_USED) && SDK_I2C_BASED_COMPONENT_USED
|
|
void BOARD_LPI2C_Init(LPI2C_Type *base, uint32_t clkSrc_Hz);
|
|
status_t BOARD_LPI2C_Send(LPI2C_Type *base,
|
|
uint8_t deviceAddress,
|
|
uint32_t subAddress,
|
|
uint8_t subaddressSize,
|
|
uint8_t *txBuff,
|
|
uint8_t txBuffSize);
|
|
status_t BOARD_LPI2C_Receive(LPI2C_Type *base,
|
|
uint8_t deviceAddress,
|
|
uint32_t subAddress,
|
|
uint8_t subaddressSize,
|
|
uint8_t *rxBuff,
|
|
uint8_t rxBuffSize);
|
|
status_t BOARD_LPI2C_SendSCCB(LPI2C_Type *base,
|
|
uint8_t deviceAddress,
|
|
uint32_t subAddress,
|
|
uint8_t subaddressSize,
|
|
uint8_t *txBuff,
|
|
uint8_t txBuffSize);
|
|
status_t BOARD_LPI2C_ReceiveSCCB(LPI2C_Type *base,
|
|
uint8_t deviceAddress,
|
|
uint32_t subAddress,
|
|
uint8_t subaddressSize,
|
|
uint8_t *rxBuff,
|
|
uint8_t rxBuffSize);
|
|
void BOARD_Accel_I2C_Init(void);
|
|
status_t BOARD_Accel_I2C_Send(uint8_t deviceAddress, uint32_t subAddress, uint8_t subaddressSize, uint32_t txBuff);
|
|
status_t BOARD_Accel_I2C_Receive(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subaddressSize, uint8_t *rxBuff, uint8_t rxBuffSize);
|
|
void BOARD_Codec_I2C_Init(void);
|
|
status_t BOARD_Codec_I2C_Send(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subAddressSize, const uint8_t *txBuff, uint8_t txBuffSize);
|
|
status_t BOARD_Codec_I2C_Receive(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subAddressSize, uint8_t *rxBuff, uint8_t rxBuffSize);
|
|
void BOARD_Camera_I2C_Init(void);
|
|
status_t BOARD_Camera_I2C_Send(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subAddressSize, const uint8_t *txBuff, uint8_t txBuffSize);
|
|
status_t BOARD_Camera_I2C_Receive(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subAddressSize, uint8_t *rxBuff, uint8_t rxBuffSize);
|
|
|
|
status_t BOARD_Camera_I2C_SendSCCB(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subAddressSize, const uint8_t *txBuff, uint8_t txBuffSize);
|
|
status_t BOARD_Camera_I2C_ReceiveSCCB(
|
|
uint8_t deviceAddress, uint32_t subAddress, uint8_t subAddressSize, uint8_t *rxBuff, uint8_t rxBuffSize);
|
|
#endif /* SDK_I2C_BASED_COMPONENT_USED */
|
|
void BOARD_SD_Pin_Config(uint32_t speed, uint32_t strength);
|
|
void BOARD_MMC_Pin_Config(uint32_t speed, uint32_t strength);
|
|
|
|
#if defined(__cplusplus)
|
|
}
|
|
#endif /* __cplusplus */
|
|
|
|
#endif /* _BOARD_H_ */
|