1469 lines
50 KiB
C
1469 lines
50 KiB
C
/**************************************************************************//**
|
|
* @file i2c.c
|
|
* @version V3.00
|
|
* @brief M480 series I2C driver source file
|
|
*
|
|
* @copyright (C) 2016 Nuvoton Technology Corp. All rights reserved.
|
|
*****************************************************************************/
|
|
#include "NuMicro.h"
|
|
|
|
/** @addtogroup Standard_Driver Standard Driver
|
|
@{
|
|
*/
|
|
|
|
/** @addtogroup I2C_Driver I2C Driver
|
|
@{
|
|
*/
|
|
|
|
|
|
/** @addtogroup I2C_EXPORTED_FUNCTIONS I2C Exported Functions
|
|
@{
|
|
*/
|
|
|
|
/**
|
|
* @brief Enable specify I2C Controller and set Clock Divider
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u32BusClock The target I2C bus clock in Hz
|
|
*
|
|
* @return Actual I2C bus clock frequency
|
|
*
|
|
* @details The function enable the specify I2C Controller and set proper Clock Divider
|
|
* in I2C CLOCK DIVIDED REGISTER (I2CLK) according to the target I2C Bus clock.
|
|
* I2C Bus clock = PCLK / (4*(divider+1).
|
|
*
|
|
*/
|
|
uint32_t I2C_Open(I2C_T *i2c, uint32_t u32BusClock)
|
|
{
|
|
uint32_t u32Div;
|
|
uint32_t u32Pclk;
|
|
|
|
if(i2c == I2C1)
|
|
{
|
|
u32Pclk = CLK_GetPCLK1Freq();
|
|
}
|
|
else
|
|
{
|
|
u32Pclk = CLK_GetPCLK0Freq();
|
|
}
|
|
|
|
u32Div = (uint32_t)(((u32Pclk * 10U) / (u32BusClock * 4U) + 5U) / 10U - 1U); /* Compute proper divider for I2C clock */
|
|
i2c->CLKDIV = u32Div;
|
|
|
|
/* Enable I2C */
|
|
i2c->CTL0 |= I2C_CTL0_I2CEN_Msk;
|
|
|
|
return (u32Pclk / ((u32Div + 1U) << 2U));
|
|
}
|
|
|
|
/**
|
|
* @brief Disable specify I2C Controller
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details Reset I2C Controller and disable specify I2C port.
|
|
*
|
|
*/
|
|
|
|
void I2C_Close(I2C_T *i2c)
|
|
{
|
|
/* Reset I2C Controller */
|
|
if((uint32_t)i2c == I2C0_BASE)
|
|
{
|
|
SYS->IPRST1 |= SYS_IPRST1_I2C0RST_Msk;
|
|
SYS->IPRST1 &= ~SYS_IPRST1_I2C0RST_Msk;
|
|
}
|
|
else if((uint32_t)i2c == I2C1_BASE)
|
|
{
|
|
SYS->IPRST1 |= SYS_IPRST1_I2C1RST_Msk;
|
|
SYS->IPRST1 &= ~SYS_IPRST1_I2C1RST_Msk;
|
|
}
|
|
|
|
/* Disable I2C */
|
|
i2c->CTL0 &= ~I2C_CTL0_I2CEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Clear Time-out Counter flag
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details When Time-out flag will be set, use this function to clear I2C Bus Time-out counter flag .
|
|
*
|
|
*/
|
|
void I2C_ClearTimeoutFlag(I2C_T *i2c)
|
|
{
|
|
i2c->TOCTL |= I2C_TOCTL_TOIF_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Set Control bit of I2C Controller
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8Start Set I2C START condition
|
|
* @param[in] u8Stop Set I2C STOP condition
|
|
* @param[in] u8Si Clear SI flag
|
|
* @param[in] u8Ack Set I2C ACK bit
|
|
*
|
|
* @return None
|
|
*
|
|
* @details The function set I2C Control bit of I2C Bus protocol.
|
|
*
|
|
*/
|
|
void I2C_Trigger(I2C_T *i2c, uint8_t u8Start, uint8_t u8Stop, uint8_t u8Si, uint8_t u8Ack)
|
|
{
|
|
uint32_t u32Reg = 0U;
|
|
|
|
if(u8Start)
|
|
{
|
|
u32Reg |= I2C_CTL_STA;
|
|
}
|
|
|
|
if(u8Stop)
|
|
{
|
|
u32Reg |= I2C_CTL_STO;
|
|
}
|
|
|
|
if(u8Si)
|
|
{
|
|
u32Reg |= I2C_CTL_SI;
|
|
}
|
|
|
|
if(u8Ack)
|
|
{
|
|
u32Reg |= I2C_CTL_AA;
|
|
}
|
|
|
|
i2c->CTL0 = (i2c->CTL0 & ~0x3CU) | u32Reg;
|
|
}
|
|
|
|
/**
|
|
* @brief Disable Interrupt of I2C Controller
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details The function is used for disable I2C interrupt
|
|
*
|
|
*/
|
|
void I2C_DisableInt(I2C_T *i2c)
|
|
{
|
|
i2c->CTL0 &= ~I2C_CTL0_INTEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Enable Interrupt of I2C Controller
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details The function is used for enable I2C interrupt
|
|
*
|
|
*/
|
|
void I2C_EnableInt(I2C_T *i2c)
|
|
{
|
|
i2c->CTL0 |= I2C_CTL0_INTEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Get I2C Bus Clock
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return The actual I2C Bus clock in Hz
|
|
*
|
|
* @details To get the actual I2C Bus Clock frequency.
|
|
*/
|
|
uint32_t I2C_GetBusClockFreq(I2C_T *i2c)
|
|
{
|
|
uint32_t u32Divider = i2c->CLKDIV;
|
|
uint32_t u32Pclk;
|
|
|
|
if(i2c == I2C1)
|
|
{
|
|
u32Pclk = CLK_GetPCLK1Freq();
|
|
}
|
|
else
|
|
{
|
|
u32Pclk = CLK_GetPCLK0Freq();
|
|
}
|
|
|
|
return (u32Pclk / ((u32Divider + 1U) << 2U));
|
|
}
|
|
|
|
/**
|
|
* @brief Set I2C Bus Clock
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u32BusClock The target I2C Bus Clock in Hz
|
|
*
|
|
* @return The actual I2C Bus Clock in Hz
|
|
*
|
|
* @details To set the actual I2C Bus Clock frequency.
|
|
*/
|
|
uint32_t I2C_SetBusClockFreq(I2C_T *i2c, uint32_t u32BusClock)
|
|
{
|
|
uint32_t u32Div;
|
|
uint32_t u32Pclk;
|
|
|
|
if(i2c == I2C1)
|
|
{
|
|
u32Pclk = CLK_GetPCLK1Freq();
|
|
}
|
|
else
|
|
{
|
|
u32Pclk = CLK_GetPCLK0Freq();
|
|
}
|
|
|
|
u32Div = (uint32_t)(((u32Pclk * 10U) / (u32BusClock * 4U) + 5U) / 10U - 1U); /* Compute proper divider for I2C clock */
|
|
i2c->CLKDIV = u32Div;
|
|
|
|
return (u32Pclk / ((u32Div + 1U) << 2U));
|
|
}
|
|
|
|
/**
|
|
* @brief Get Interrupt Flag
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return I2C interrupt flag status
|
|
*
|
|
* @details To get I2C Bus interrupt flag.
|
|
*/
|
|
uint32_t I2C_GetIntFlag(I2C_T *i2c)
|
|
{
|
|
uint32_t u32Value;
|
|
|
|
if((i2c->CTL0 & I2C_CTL0_SI_Msk) == I2C_CTL0_SI_Msk)
|
|
{
|
|
u32Value = 1U;
|
|
}
|
|
else
|
|
{
|
|
u32Value = 0U;
|
|
}
|
|
|
|
return u32Value;
|
|
}
|
|
|
|
/**
|
|
* @brief Get I2C Bus Status Code
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return I2C Status Code
|
|
*
|
|
* @details To get I2C Bus Status Code.
|
|
*/
|
|
uint32_t I2C_GetStatus(I2C_T *i2c)
|
|
{
|
|
return (i2c->STATUS0);
|
|
}
|
|
|
|
/**
|
|
* @brief Read a Byte from I2C Bus
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return I2C Data
|
|
*
|
|
* @details To read a bytes data from specify I2C port.
|
|
*/
|
|
uint8_t I2C_GetData(I2C_T *i2c)
|
|
{
|
|
return (uint8_t)(i2c->DAT);
|
|
}
|
|
|
|
/**
|
|
* @brief Send a byte to I2C Bus
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8Data The data to send to I2C bus
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function is used to write a byte to specified I2C port
|
|
*/
|
|
void I2C_SetData(I2C_T *i2c, uint8_t u8Data)
|
|
{
|
|
i2c->DAT = u8Data;
|
|
}
|
|
|
|
/**
|
|
* @brief Set 7-bit Slave Address and GC Mode
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8SlaveNo Set the number of I2C address register (0~3)
|
|
* @param[in] u8SlaveAddr 7-bit slave address
|
|
* @param[in] u8GCMode Enable/Disable GC mode (I2C_GCMODE_ENABLE / I2C_GCMODE_DISABLE)
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function is used to set 7-bit slave addresses in I2C SLAVE ADDRESS REGISTER (I2CADDR0~3)
|
|
* and enable GC Mode.
|
|
*
|
|
*/
|
|
void I2C_SetSlaveAddr(I2C_T *i2c, uint8_t u8SlaveNo, uint8_t u8SlaveAddr, uint8_t u8GCMode)
|
|
{
|
|
switch(u8SlaveNo)
|
|
{
|
|
case 1:
|
|
i2c->ADDR1 = ((uint32_t)u8SlaveAddr << 1U) | u8GCMode;
|
|
break;
|
|
case 2:
|
|
i2c->ADDR2 = ((uint32_t)u8SlaveAddr << 1U) | u8GCMode;
|
|
break;
|
|
case 3:
|
|
i2c->ADDR3 = ((uint32_t)u8SlaveAddr << 1U) | u8GCMode;
|
|
break;
|
|
case 0:
|
|
default:
|
|
i2c->ADDR0 = ((uint32_t)u8SlaveAddr << 1U) | u8GCMode;
|
|
break;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Configure the mask bits of 7-bit Slave Address
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8SlaveNo Set the number of I2C address mask register (0~3)
|
|
* @param[in] u8SlaveAddrMask A byte for slave address mask
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function is used to set 7-bit slave addresses.
|
|
*
|
|
*/
|
|
void I2C_SetSlaveAddrMask(I2C_T *i2c, uint8_t u8SlaveNo, uint8_t u8SlaveAddrMask)
|
|
{
|
|
switch(u8SlaveNo)
|
|
{
|
|
case 1:
|
|
i2c->ADDRMSK1 = (uint32_t)u8SlaveAddrMask << 1U;
|
|
break;
|
|
case 2:
|
|
i2c->ADDRMSK2 = (uint32_t)u8SlaveAddrMask << 1U;
|
|
break;
|
|
case 3:
|
|
i2c->ADDRMSK3 = (uint32_t)u8SlaveAddrMask << 1U;
|
|
break;
|
|
case 0:
|
|
default:
|
|
i2c->ADDRMSK0 = (uint32_t)u8SlaveAddrMask << 1U;
|
|
break;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Enable Time-out Counter Function and support Long Time-out
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8LongTimeout Configure DIV4 to enable Long Time-out (0/1)
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function enable Time-out Counter function and configure DIV4 to support Long
|
|
* Time-out.
|
|
*
|
|
*/
|
|
void I2C_EnableTimeout(I2C_T *i2c, uint8_t u8LongTimeout)
|
|
{
|
|
if(u8LongTimeout)
|
|
{
|
|
i2c->TOCTL |= I2C_TOCTL_TOCDIV4_Msk;
|
|
}
|
|
else
|
|
{
|
|
i2c->TOCTL &= ~I2C_TOCTL_TOCDIV4_Msk;
|
|
}
|
|
|
|
i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Disable Time-out Counter Function
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details To disable Time-out Counter function in I2CTOC register.
|
|
*
|
|
*/
|
|
void I2C_DisableTimeout(I2C_T *i2c)
|
|
{
|
|
i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Enable I2C Wake-up Function
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details To enable Wake-up function of I2C Wake-up control register.
|
|
*
|
|
*/
|
|
void I2C_EnableWakeup(I2C_T *i2c)
|
|
{
|
|
i2c->WKCTL |= I2C_WKCTL_WKEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief Disable I2C Wake-up Function
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details To disable Wake-up function of I2C Wake-up control register.
|
|
*
|
|
*/
|
|
void I2C_DisableWakeup(I2C_T *i2c)
|
|
{
|
|
i2c->WKCTL &= ~I2C_WKCTL_WKEN_Msk;
|
|
}
|
|
|
|
/**
|
|
* @brief To get SMBus Status
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return SMBus status
|
|
*
|
|
* @details To get the Bus Management status of I2C_BUSSTS register
|
|
*
|
|
*/
|
|
uint32_t I2C_SMBusGetStatus(I2C_T *i2c)
|
|
{
|
|
return (i2c->BUSSTS);
|
|
}
|
|
|
|
/**
|
|
* @brief Clear SMBus Interrupt Flag
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8SMBusIntFlag Specify SMBus interrupt flag
|
|
*
|
|
* @return None
|
|
*
|
|
* @details To clear flags of I2C_BUSSTS status register if interrupt set.
|
|
*
|
|
*/
|
|
void I2C_SMBusClearInterruptFlag(I2C_T *i2c, uint8_t u8SMBusIntFlag)
|
|
{
|
|
i2c->BUSSTS = u8SMBusIntFlag;
|
|
}
|
|
|
|
/**
|
|
* @brief Set SMBus Bytes Counts of Transmission or Reception
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u32PktSize Transmit / Receive bytes
|
|
*
|
|
* @return None
|
|
*
|
|
* @details The transmission or receive byte number in one transaction when PECEN is set. The maximum is 255 bytes.
|
|
*
|
|
*/
|
|
void I2C_SMBusSetPacketByteCount(I2C_T *i2c, uint32_t u32PktSize)
|
|
{
|
|
i2c->PKTSIZE = u32PktSize;
|
|
}
|
|
|
|
/**
|
|
* @brief Init SMBus Host/Device Mode
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8HostDevice Init SMBus port mode(I2C_SMBH_ENABLE(1)/I2C_SMBD_ENABLE(0))
|
|
*
|
|
* @return None
|
|
*
|
|
* @details Using SMBus communication must specify the port is a Host or a Device.
|
|
*
|
|
*/
|
|
void I2C_SMBusOpen(I2C_T *i2c, uint8_t u8HostDevice)
|
|
{
|
|
/* Clear BMHEN, BMDEN of BUSCTL Register */
|
|
i2c->BUSCTL &= ~(I2C_BUSCTL_BMHEN_Msk | I2C_BUSCTL_BMDEN_Msk);
|
|
|
|
/* Set SMBus Host/Device Mode, and enable Bus Management*/
|
|
if(u8HostDevice == (uint8_t)I2C_SMBH_ENABLE)
|
|
{
|
|
i2c->BUSCTL |= (I2C_BUSCTL_BMHEN_Msk | I2C_BUSCTL_BUSEN_Msk);
|
|
}
|
|
else
|
|
{
|
|
i2c->BUSCTL |= (I2C_BUSCTL_BMDEN_Msk | I2C_BUSCTL_BUSEN_Msk);
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Disable SMBus function
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return None
|
|
*
|
|
* @details Disable all SMBus function include Bus disable, CRC check, Acknowledge by manual, Host/Device Mode.
|
|
*
|
|
*/
|
|
void I2C_SMBusClose(I2C_T *i2c)
|
|
{
|
|
|
|
i2c->BUSCTL = 0x00U;
|
|
}
|
|
|
|
/**
|
|
* @brief Enable SMBus PEC Transmit Function
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] u8PECTxEn CRC transmit enable(PECTX_ENABLE) or disable(PECTX_DISABLE)
|
|
*
|
|
* @return None
|
|
*
|
|
* @details When enable CRC check function, the Host or Device needs to transmit CRC byte.
|
|
*
|
|
*/
|
|
void I2C_SMBusPECTxEnable(I2C_T *i2c, uint8_t u8PECTxEn)
|
|
{
|
|
i2c->BUSCTL &= ~I2C_BUSCTL_PECTXEN_Msk;
|
|
|
|
if(u8PECTxEn)
|
|
{
|
|
i2c->BUSCTL |= (I2C_BUSCTL_PECEN_Msk | I2C_BUSCTL_PECTXEN_Msk);
|
|
}
|
|
else
|
|
{
|
|
i2c->BUSCTL |= I2C_BUSCTL_PECEN_Msk;
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Get SMBus CRC value
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
*
|
|
* @return A byte is packet error check value
|
|
*
|
|
* @details The CRC check value after a transmission or a reception by count by using CRC8
|
|
*
|
|
*/
|
|
uint8_t I2C_SMBusGetPECValue(I2C_T *i2c)
|
|
{
|
|
return (uint8_t)i2c->PKTCRC;
|
|
}
|
|
|
|
/**
|
|
* @brief Calculate Time-out of SMBus idle period
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] us Time-out length(us)
|
|
* @param[in] u32Hclk I2C peripheral clock frequency
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function is used to set SMBus Time-out length when bus is in Idle state.
|
|
*
|
|
*/
|
|
|
|
void I2C_SMBusIdleTimeout(I2C_T *i2c, uint32_t us, uint32_t u32Hclk)
|
|
{
|
|
uint32_t u32Div, u32Hclk_kHz;
|
|
|
|
i2c->BUSCTL |= I2C_BUSCTL_TIDLE_Msk;
|
|
u32Hclk_kHz = u32Hclk / 1000U;
|
|
u32Div = (((us * u32Hclk_kHz) / 1000U) >> 2U) - 1U;
|
|
if(u32Div > 255U)
|
|
{
|
|
i2c->BUSTOUT = 0xFFU;
|
|
}
|
|
else
|
|
{
|
|
i2c->BUSTOUT = u32Div;
|
|
}
|
|
|
|
}
|
|
|
|
/**
|
|
* @brief Calculate Time-out of SMBus active period
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] ms Time-out length(ms)
|
|
* @param[in] u32Pclk peripheral clock frequency
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function is used to set SMBus Time-out length when bus is in active state.
|
|
* Time-out length is calculate the SCL line "one clock" pull low timing.
|
|
*
|
|
*/
|
|
|
|
void I2C_SMBusTimeout(I2C_T *i2c, uint32_t ms, uint32_t u32Pclk)
|
|
{
|
|
uint32_t u32Div, u32Pclk_kHz;
|
|
|
|
i2c->BUSCTL &= ~I2C_BUSCTL_TIDLE_Msk;
|
|
|
|
/* DIV4 disabled */
|
|
i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk;
|
|
u32Pclk_kHz = u32Pclk / 1000U;
|
|
u32Div = ((ms * u32Pclk_kHz) / (16U * 1024U)) - 1U;
|
|
if(u32Div <= 0xFFU)
|
|
{
|
|
i2c->BUSTOUT = u32Div;
|
|
}
|
|
else
|
|
{
|
|
/* DIV4 enabled */
|
|
i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk;
|
|
i2c->BUSTOUT = (((ms * u32Pclk_kHz) / (16U * 1024U * 4U)) - 1U) & 0xFFU; /* The max value is 255 */
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief Calculate Cumulative Clock low Time-out of SMBus active period
|
|
*
|
|
* @param[in] i2c Specify I2C port
|
|
* @param[in] ms Time-out length(ms)
|
|
* @param[in] u32Pclk peripheral clock frequency
|
|
*
|
|
* @return None
|
|
*
|
|
* @details This function is used to set SMBus Time-out length when bus is in Active state.
|
|
* Time-out length is calculate the SCL line "clocks" low cumulative timing.
|
|
*
|
|
*/
|
|
|
|
void I2C_SMBusClockLoTimeout(I2C_T *i2c, uint32_t ms, uint32_t u32Pclk)
|
|
{
|
|
uint32_t u32Div, u32Pclk_kHz;
|
|
|
|
i2c->BUSCTL &= ~I2C_BUSCTL_TIDLE_Msk;
|
|
|
|
/* DIV4 disabled */
|
|
i2c->TOCTL &= ~I2C_TOCTL_TOCEN_Msk;
|
|
u32Pclk_kHz = u32Pclk / 1000U;
|
|
u32Div = ((ms * u32Pclk_kHz) / (16U * 1024U)) - 1U;
|
|
if(u32Div <= 0xFFU)
|
|
{
|
|
i2c->CLKTOUT = u32Div;
|
|
}
|
|
else
|
|
{
|
|
/* DIV4 enabled */
|
|
i2c->TOCTL |= I2C_TOCTL_TOCEN_Msk;
|
|
i2c->CLKTOUT = (((ms * u32Pclk_kHz) / (16U * 1024U * 4U)) - 1U) & 0xFFU; /* The max value is 255 */
|
|
}
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief Write a byte to Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] data Write a byte data to Slave
|
|
*
|
|
* @retval 0 Write data success
|
|
* @retval 1 Write data fail, or bus occurs error events
|
|
*
|
|
* @details The function is used for I2C Master write a byte data to Slave.
|
|
*
|
|
*/
|
|
|
|
uint8_t I2C_WriteByte(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t data)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
|
|
|
|
I2C_START(i2c);
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, data); /* Write data to I2CDAT */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return (u8Err | u8Xfering); /* return (Success)/(Fail) status */
|
|
}
|
|
|
|
/**
|
|
* @brief Write multi bytes to Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] *data Pointer to array to write data to Slave
|
|
* @param[in] u32wLen How many bytes need to write to Slave
|
|
*
|
|
* @return A length of how many bytes have been transmitted.
|
|
*
|
|
* @details The function is used for I2C Master write multi bytes data to Slave.
|
|
*
|
|
*/
|
|
|
|
uint32_t I2C_WriteMultiBytes(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t data[], uint32_t u32wLen)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
|
|
uint32_t u32txLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
case 0x28u:
|
|
if(u32txLen < u32wLen)
|
|
{
|
|
I2C_SET_DATA(i2c, data[u32txLen++]); /* Write Data to I2CDAT */
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
}
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return u32txLen; /* Return bytes length that have been transmitted */
|
|
}
|
|
|
|
/**
|
|
* @brief Specify a byte register address and write a byte to Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u8DataAddr Specify a address (1 byte) of data write to
|
|
* @param[in] data A byte data to write it to Slave
|
|
*
|
|
* @retval 0 Write data success
|
|
* @retval 1 Write data fail, or bus occurs error events
|
|
*
|
|
* @details The function is used for I2C Master specify a address that data write to in Slave.
|
|
*
|
|
*/
|
|
|
|
uint8_t I2C_WriteByteOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr, uint8_t data)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
|
|
uint32_t u32txLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Send Slave address with write bit */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, u8DataAddr); /* Write Lo byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
if(u32txLen < 1u)
|
|
{
|
|
I2C_SET_DATA(i2c, data);
|
|
u32txLen++;
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
}
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return (u8Err | u8Xfering); /* return (Success)/(Fail) status */
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief Specify a byte register address and write multi bytes to Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u8DataAddr Specify a address (1 byte) of data write to
|
|
* @param[in] *data Pointer to array to write data to Slave
|
|
* @param[in] u32wLen How many bytes need to write to Slave
|
|
*
|
|
* @return A length of how many bytes have been transmitted.
|
|
*
|
|
* @details The function is used for I2C Master specify a byte address that multi data bytes write to in Slave.
|
|
*
|
|
*/
|
|
|
|
uint32_t I2C_WriteMultiBytesOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr, uint8_t data[], uint32_t u32wLen)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
|
|
uint32_t u32txLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI;
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, u8DataAddr); /* Write Lo byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
if(u32txLen < u32wLen)
|
|
{
|
|
I2C_SET_DATA(i2c, data[u32txLen++]);
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
}
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
|
|
return u32txLen; /* Return bytes length that have been transmitted */
|
|
}
|
|
|
|
/**
|
|
* @brief Specify two bytes register address and Write a byte to Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u16DataAddr Specify a address (2 byte) of data write to
|
|
* @param[in] data Write a byte data to Slave
|
|
*
|
|
* @retval 0 Write data success
|
|
* @retval 1 Write data fail, or bus occurs error events
|
|
*
|
|
* @details The function is used for I2C Master specify two bytes address that data write to in Slave.
|
|
*
|
|
*/
|
|
|
|
uint8_t I2C_WriteByteTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr, uint8_t data)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Addr = 1u, u8Ctrl = 0u;
|
|
uint32_t u32txLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u)); /* Write Hi byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
if(u8Addr)
|
|
{
|
|
I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu)); /* Write Lo byte address of register */
|
|
u8Addr = 0u;
|
|
}
|
|
else if((u32txLen < 1u) && (u8Addr == 0u))
|
|
{
|
|
I2C_SET_DATA(i2c, data);
|
|
u32txLen++;
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
}
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return (u8Err | u8Xfering); /* return (Success)/(Fail) status */
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief Specify two bytes register address and write multi bytes to Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u16DataAddr Specify a address (2 bytes) of data write to
|
|
* @param[in] data[] A data array for write data to Slave
|
|
* @param[in] u32wLen How many bytes need to write to Slave
|
|
*
|
|
* @return A length of how many bytes have been transmitted.
|
|
*
|
|
* @details The function is used for I2C Master specify a byte address that multi data write to in Slave.
|
|
*
|
|
*/
|
|
|
|
uint32_t I2C_WriteMultiBytesTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr, uint8_t data[], uint32_t u32wLen)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Addr = 1u, u8Ctrl = 0u;
|
|
uint32_t u32txLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u)); /* Write Hi byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
if(u8Addr)
|
|
{
|
|
I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu)); /* Write Lo byte address of register */
|
|
u8Addr = 0u;
|
|
}
|
|
else if((u32txLen < u32wLen) && (u8Addr == 0u))
|
|
{
|
|
I2C_SET_DATA(i2c, data[u32txLen++]); /* Write data to Register I2CDAT*/
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
}
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return u32txLen; /* Return bytes length that have been transmitted */
|
|
}
|
|
|
|
/**
|
|
* @brief Read a byte from Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
*
|
|
* @return Read a byte data from Slave
|
|
*
|
|
* @details The function is used for I2C Master to read a byte data from Slave.
|
|
*
|
|
*/
|
|
uint8_t I2C_ReadByte(I2C_T *i2c, uint8_t u8SlaveAddr)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, rdata = 0u, u8Ctrl = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u)); /* Write SLA+R to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x40u: /* Slave Address ACK */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x48u: /* Slave Address NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x58u:
|
|
rdata = (unsigned char) I2C_GET_DATA(i2c); /* Receive Data */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
if(u8Err)
|
|
{
|
|
rdata = 0u; /* If occurs error, return 0 */
|
|
}
|
|
return rdata; /* Return read data */
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief Read multi bytes from Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[out] rdata[] A data array to store data from Slave
|
|
* @param[in] u32rLen How many bytes need to read from Slave
|
|
*
|
|
* @return A length of how many bytes have been received
|
|
*
|
|
* @details The function is used for I2C Master to read multi data bytes from Slave.
|
|
*
|
|
*
|
|
*/
|
|
uint32_t I2C_ReadMultiBytes(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t rdata[], uint32_t u32rLen)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
|
|
uint32_t u32rxLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u)); /* Write SLA+R to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x40u: /* Slave Address ACK */
|
|
u8Ctrl = I2C_CTL_SI_AA; /* Clear SI and set ACK */
|
|
break;
|
|
case 0x48u: /* Slave Address NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x50u:
|
|
rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c); /* Receive Data */
|
|
if(u32rxLen < (u32rLen - 1u))
|
|
{
|
|
u8Ctrl = I2C_CTL_SI_AA; /* Clear SI and set ACK */
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
}
|
|
break;
|
|
case 0x58u:
|
|
rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c); /* Receive Data */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return u32rxLen; /* Return bytes length that have been received */
|
|
}
|
|
|
|
|
|
/**
|
|
* @brief Specify a byte register address and read a byte from Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u8DataAddr Specify a address(1 byte) of data read from
|
|
*
|
|
* @return Read a byte data from Slave
|
|
*
|
|
* @details The function is used for I2C Master specify a byte address that a data byte read from Slave.
|
|
*
|
|
*
|
|
*/
|
|
uint8_t I2C_ReadByteOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, rdata = 0u, u8Ctrl = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, u8DataAddr); /* Write Lo byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
u8Ctrl = I2C_CTL_STA_SI; /* Send repeat START */
|
|
break;
|
|
case 0x10u:
|
|
I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u)); /* Write SLA+R to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x40u: /* Slave Address ACK */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x48u: /* Slave Address NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x58u:
|
|
rdata = (uint8_t) I2C_GET_DATA(i2c); /* Receive Data */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
if(u8Err)
|
|
{
|
|
rdata = 0u; /* If occurs error, return 0 */
|
|
}
|
|
return rdata; /* Return read data */
|
|
}
|
|
|
|
/**
|
|
* @brief Specify a byte register address and read multi bytes from Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u8DataAddr Specify a address (1 bytes) of data read from
|
|
* @param[out] rdata[] A data array to store data from Slave
|
|
* @param[in] u32rLen How many bytes need to read from Slave
|
|
*
|
|
* @return A length of how many bytes have been received
|
|
*
|
|
* @details The function is used for I2C Master specify a byte address that multi data bytes read from Slave.
|
|
*
|
|
*
|
|
*/
|
|
uint32_t I2C_ReadMultiBytesOneReg(I2C_T *i2c, uint8_t u8SlaveAddr, uint8_t u8DataAddr, uint8_t rdata[], uint32_t u32rLen)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Ctrl = 0u;
|
|
uint32_t u32rxLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, u8DataAddr); /* Write Lo byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
u8Ctrl = I2C_CTL_STA_SI; /* Send repeat START */
|
|
break;
|
|
case 0x10u:
|
|
I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u)); /* Write SLA+R to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x40u: /* Slave Address ACK */
|
|
u8Ctrl = I2C_CTL_SI_AA; /* Clear SI and set ACK */
|
|
break;
|
|
case 0x48u: /* Slave Address NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x50u:
|
|
rdata[u32rxLen++] = (uint8_t) I2C_GET_DATA(i2c); /* Receive Data */
|
|
if(u32rxLen < (u32rLen - 1u))
|
|
{
|
|
u8Ctrl = I2C_CTL_SI_AA; /* Clear SI and set ACK */
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
}
|
|
break;
|
|
case 0x58u:
|
|
rdata[u32rxLen++] = (uint8_t) I2C_GET_DATA(i2c); /* Receive Data */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return u32rxLen; /* Return bytes length that have been received */
|
|
}
|
|
|
|
/**
|
|
* @brief Specify two bytes register address and read a byte from Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u16DataAddr Specify an address(2 bytes) of data read from
|
|
*
|
|
* @return Read a byte data from Slave
|
|
*
|
|
* @details The function is used for I2C Master specify two bytes address that a data byte read from Slave.
|
|
*
|
|
*
|
|
*/
|
|
uint8_t I2C_ReadByteTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, rdata = 0u, u8Addr = 1u, u8Ctrl = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u)); /* Write Hi byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
if(u8Addr)
|
|
{
|
|
I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu)); /* Write Lo byte address of register */
|
|
u8Addr = 0u;
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STA_SI; /* Clear SI and send repeat START */
|
|
}
|
|
break;
|
|
case 0x10u:
|
|
I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u)); /* Write SLA+R to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x40u: /* Slave Address ACK */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x48u: /* Slave Address NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x58u:
|
|
rdata = (unsigned char) I2C_GET_DATA(i2c); /* Receive Data */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
if(u8Err)
|
|
{
|
|
rdata = 0u; /* If occurs error, return 0 */
|
|
}
|
|
return rdata; /* Return read data */
|
|
}
|
|
|
|
/**
|
|
* @brief Specify two bytes register address and read multi bytes from Slave
|
|
*
|
|
* @param[in] *i2c Point to I2C peripheral
|
|
* @param[in] u8SlaveAddr Access Slave address(7-bit)
|
|
* @param[in] u16DataAddr Specify a address (2 bytes) of data read from
|
|
* @param[out] rdata[] A data array to store data from Slave
|
|
* @param[in] u32rLen How many bytes need to read from Slave
|
|
*
|
|
* @return A length of how many bytes have been received
|
|
*
|
|
* @details The function is used for I2C Master specify two bytes address that multi data bytes read from Slave.
|
|
*
|
|
*
|
|
*/
|
|
uint32_t I2C_ReadMultiBytesTwoRegs(I2C_T *i2c, uint8_t u8SlaveAddr, uint16_t u16DataAddr, uint8_t rdata[], uint32_t u32rLen)
|
|
{
|
|
uint8_t u8Xfering = 1u, u8Err = 0u, u8Addr = 1u, u8Ctrl = 0u;
|
|
uint32_t u32rxLen = 0u;
|
|
|
|
I2C_START(i2c); /* Send START */
|
|
while(u8Xfering && (u8Err == 0u))
|
|
{
|
|
I2C_WAIT_READY(i2c) {}
|
|
switch(I2C_GET_STATUS(i2c))
|
|
{
|
|
case 0x08u:
|
|
I2C_SET_DATA(i2c, (uint8_t)(u8SlaveAddr << 1u | 0x00u)); /* Write SLA+W to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x18u: /* Slave Address ACK */
|
|
I2C_SET_DATA(i2c, (uint8_t)((u16DataAddr & 0xFF00u) >> 8u)); /* Write Hi byte address of register */
|
|
break;
|
|
case 0x20u: /* Slave Address NACK */
|
|
case 0x30u: /* Master transmit data NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x28u:
|
|
if(u8Addr)
|
|
{
|
|
I2C_SET_DATA(i2c, (uint8_t)(u16DataAddr & 0xFFu)); /* Write Lo byte address of register */
|
|
u8Addr = 0u;
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_STA_SI; /* Clear SI and send repeat START */
|
|
}
|
|
break;
|
|
case 0x10u:
|
|
I2C_SET_DATA(i2c, (uint8_t)((u8SlaveAddr << 1u) | 0x01u)); /* Write SLA+R to Register I2CDAT */
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
break;
|
|
case 0x40u: /* Slave Address ACK */
|
|
u8Ctrl = I2C_CTL_SI_AA; /* Clear SI and set ACK */
|
|
break;
|
|
case 0x48u: /* Slave Address NACK */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
case 0x50u:
|
|
rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c); /* Receive Data */
|
|
if(u32rxLen < (u32rLen - 1u))
|
|
{
|
|
u8Ctrl = I2C_CTL_SI_AA; /* Clear SI and set ACK */
|
|
}
|
|
else
|
|
{
|
|
u8Ctrl = I2C_CTL_SI; /* Clear SI */
|
|
}
|
|
break;
|
|
case 0x58u:
|
|
rdata[u32rxLen++] = (unsigned char) I2C_GET_DATA(i2c); /* Receive Data */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Xfering = 0u;
|
|
break;
|
|
case 0x38u: /* Arbitration Lost */
|
|
default: /* Unknow status */
|
|
u8Ctrl = I2C_CTL_STO_SI; /* Clear SI and send STOP */
|
|
u8Err = 1u;
|
|
break;
|
|
}
|
|
I2C_SET_CONTROL_REG(i2c, u8Ctrl); /* Write controlbit to I2C_CTL register */
|
|
}
|
|
return u32rxLen; /* Return bytes length that have been received */
|
|
}
|
|
|
|
|
|
/*@}*/ /* end of group I2C_EXPORTED_FUNCTIONS */
|
|
|
|
/*@}*/ /* end of group I2C_Driver */
|
|
|
|
/*@}*/ /* end of group Standard_Driver */
|
|
|
|
/*** (C) COPYRIGHT 2016 Nuvoton Technology Corp. ***/
|