rt-thread/bsp/nuvoton/numaker-m2354
Meco Man 9bc68d26a4 format Kconfig and sconscript 2023-01-08 22:52:13 -05:00
..
applications Sync upstream (#6793) 2022-12-29 15:15:13 +08:00
board format Kconfig and sconscript 2023-01-08 22:52:13 -05:00
linking_scripts Support M2354 platform. 2021-02-05 18:52:13 +08:00
.config [bsp/nuvoton] Support NuMaker-IoT-M467 board (#6448) 2022-09-20 10:30:21 -04:00
Kconfig format Kconfig and sconscript 2023-01-08 22:52:13 -05:00
README.md Correct rvds.S including for armclang platform. 2021-05-10 16:17:11 +08:00
SConscript Support M2354 platform. 2021-02-05 18:52:13 +08:00
SConstruct [Scons][iar][iccarm] IAR统一使用iccarm作为判断条件而不是是用IDE的名字来进行判断 2022-06-09 07:01:59 +08:00
config_lvgl [bsp/nuvoton] Update. (#6022) 2022-06-03 10:01:15 +08:00
rtconfig.py [scons][iar] 将IAR的PLATFORM字段由iar调整为iccarm 2022-06-09 07:01:59 +08:00
template.ewd Support M2354 platform. 2021-02-05 18:52:13 +08:00
template.ewp Support M2354 platform. 2021-02-05 18:52:13 +08:00
template.eww Support M2354 platform. 2021-02-05 18:52:13 +08:00
template.uvprojx Support M2354 platform. 2021-02-05 18:52:13 +08:00

README.md

NuMaker-M2354

1. Introduction

The NuMaker-M2354 is an evaluation board for Nuvoton NuMicro M2354 microcontrollers. The NuMaker-M2354 consists of two parts, a M2354 target board and an on-board Nu-Link2-Me debugger and programmer. The NuMaker-M2354 is designed for secure evaluation, prototype development and validation with power consumption monitoring function.

NuMaker-M2354

1.1 MCU specification

Features
MCU M2354KJFAE
Operation frequency 96MHz
embedded Flash size 1MB, Dual Bank
SRAM size 256kB
Crypto engine PRNG, AES, ECC, RSA, HMAC and SHA crypto accelerator

1.2 Interface

Interface
Arduino UNO
USB 1.1 OTG ports
A microSD slot
A segment LCD port

1.3 On-board devices

Device Description Driver supporting status
Wi-Fi module ESP8266-ESP12, AT firmware v1.7 Supported
Segment LCD module Supported

2. Supported compiler

Support GCC, MDK5, IAR IDE/compilers. More information of these compiler version as following:

IDE/Compiler Tested version
MDK5 5.26.2
IAR 8.32
GCC GCC 6.3.1 20170620 (Need update env)

Notice: (1) Please install Nu-Link_Keil_Driver or Nu-Link_IAR_Driver for development.

3. Program firmware

Step 1:

At first, you need to configure ISW1 switch on the NuMaker-M2354 board. Set the four switches to ON position. After the configuration is done, connect the NuMaker-M2354 board and your computer using the USB Micro cable. After that, window manager will show a NuMicro MCU virtual disk. Finally, you will use this virtual disk to burn firmware.

NuLinkMe

NuMicro MCU

Step 2:

A simple firmware burning method is that you can drag and drop the binary image file to NuMicro MCU virtual disk or copy the binary file to NuMicro MCU disk to burn firmware.

CopyTo

4. Test

You can use Tera Term terminate emulator (or other software) to type commands of RTT. All parameters of serial communication are shown in below image. Here, you can find out the corresponding port number of Nuvoton Virtual Com Port in window device manager.

Serial settings

5. Purchase

6. Resources