rt-thread/bsp/imxrt1052-evk/Libraries/drivers/fsl_flexio_i2c_master.h

484 lines
18 KiB
C

/*
* Copyright (c) 2015, Freescale Semiconductor, Inc.
* Copyright 2016-2017 NXP
*
* Redistribution and use in source and binary forms, with or without modification,
* are permitted provided that the following conditions are met:
*
* o Redistributions of source code must retain the above copyright notice, this list
* of conditions and the following disclaimer.
*
* o Redistributions in binary form must reproduce the above copyright notice, this
* list of conditions and the following disclaimer in the documentation and/or
* other materials provided with the distribution.
*
* o Neither the name of the copyright holder nor the names of its
* contributors may be used to endorse or promote products derived from this
* software without specific prior written permission.
*
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
*/
#ifndef _FSL_FLEXIO_I2C_MASTER_H_
#define _FSL_FLEXIO_I2C_MASTER_H_
#include "fsl_common.h"
#include "fsl_flexio.h"
/*!
* @addtogroup flexio_i2c_master
* @{
*/
/*******************************************************************************
* Definitions
******************************************************************************/
/*! @name Driver version */
/*@{*/
/*! @brief FlexIO I2C master driver version 2.1.2. */
#define FSL_FLEXIO_I2C_MASTER_DRIVER_VERSION (MAKE_VERSION(2, 1, 2))
/*@}*/
/*! @brief FlexIO I2C transfer status*/
enum _flexio_i2c_status
{
kStatus_FLEXIO_I2C_Busy = MAKE_STATUS(kStatusGroup_FLEXIO_I2C, 0), /*!< I2C is busy doing transfer. */
kStatus_FLEXIO_I2C_Idle = MAKE_STATUS(kStatusGroup_FLEXIO_I2C, 1), /*!< I2C is busy doing transfer. */
kStatus_FLEXIO_I2C_Nak = MAKE_STATUS(kStatusGroup_FLEXIO_I2C, 2), /*!< NAK received during transfer. */
};
/*! @brief Define FlexIO I2C master interrupt mask. */
enum _flexio_i2c_master_interrupt
{
kFLEXIO_I2C_TxEmptyInterruptEnable = 0x1U, /*!< Tx buffer empty interrupt enable. */
kFLEXIO_I2C_RxFullInterruptEnable = 0x2U, /*!< Rx buffer full interrupt enable. */
};
/*! @brief Define FlexIO I2C master status mask. */
enum _flexio_i2c_master_status_flags
{
kFLEXIO_I2C_TxEmptyFlag = 0x1U, /*!< Tx shifter empty flag. */
kFLEXIO_I2C_RxFullFlag = 0x2U, /*!< Rx shifter full/Transfer complete flag. */
kFLEXIO_I2C_ReceiveNakFlag = 0x4U, /*!< Receive NAK flag. */
};
/*! @brief Direction of master transfer.*/
typedef enum _flexio_i2c_direction
{
kFLEXIO_I2C_Write = 0x0U, /*!< Master send to slave. */
kFLEXIO_I2C_Read = 0x1U, /*!< Master receive from slave. */
} flexio_i2c_direction_t;
/*! @brief Define FlexIO I2C master access structure typedef. */
typedef struct _flexio_i2c_type
{
FLEXIO_Type *flexioBase; /*!< FlexIO base pointer. */
uint8_t SDAPinIndex; /*!< Pin select for I2C SDA. */
uint8_t SCLPinIndex; /*!< Pin select for I2C SCL. */
uint8_t shifterIndex[2]; /*!< Shifter index used in FlexIO I2C. */
uint8_t timerIndex[2]; /*!< Timer index used in FlexIO I2C. */
} FLEXIO_I2C_Type;
/*! @brief Define FlexIO I2C master user configuration structure. */
typedef struct _flexio_i2c_master_config
{
bool enableMaster; /*!< Enables the FlexIO I2C peripheral at initialization time. */
bool enableInDoze; /*!< Enable/disable FlexIO operation in doze mode. */
bool enableInDebug; /*!< Enable/disable FlexIO operation in debug mode. */
bool enableFastAccess; /*!< Enable/disable fast access to FlexIO registers, fast access requires
the FlexIO clock to be at least twice the frequency of the bus clock. */
uint32_t baudRate_Bps; /*!< Baud rate in Bps. */
} flexio_i2c_master_config_t;
/*! @brief Define FlexIO I2C master transfer structure. */
typedef struct _flexio_i2c_master_transfer
{
uint32_t flags; /*!< Transfer flag which controls the transfer, reserved for FlexIO I2C. */
uint8_t slaveAddress; /*!< 7-bit slave address. */
flexio_i2c_direction_t direction; /*!< Transfer direction, read or write. */
uint32_t subaddress; /*!< Sub address. Transferred MSB first. */
uint8_t subaddressSize; /*!< Size of command buffer. */
uint8_t volatile *data; /*!< Transfer buffer. */
volatile size_t dataSize; /*!< Transfer size. */
} flexio_i2c_master_transfer_t;
/*! @brief FlexIO I2C master handle typedef. */
typedef struct _flexio_i2c_master_handle flexio_i2c_master_handle_t;
/*! @brief FlexIO I2C master transfer callback typedef. */
typedef void (*flexio_i2c_master_transfer_callback_t)(FLEXIO_I2C_Type *base,
flexio_i2c_master_handle_t *handle,
status_t status,
void *userData);
/*! @brief Define FlexIO I2C master handle structure. */
struct _flexio_i2c_master_handle
{
flexio_i2c_master_transfer_t transfer; /*!< FlexIO I2C master transfer copy. */
size_t transferSize; /*!< Total bytes to be transferred. */
uint8_t state; /*!< Transfer state maintained during transfer. */
flexio_i2c_master_transfer_callback_t completionCallback; /*!< Callback function called at transfer event. */
/*!< Callback function called at transfer event. */
void *userData; /*!< Callback parameter passed to callback function. */
};
/*******************************************************************************
* API
******************************************************************************/
#if defined(__cplusplus)
extern "C" {
#endif /*_cplusplus*/
/*!
* @name Initialization and deinitialization
* @{
*/
/*!
* @brief Ungates the FlexIO clock, resets the FlexIO module, and configures the FlexIO I2C
* hardware configuration.
*
* Example
@code
FLEXIO_I2C_Type base = {
.flexioBase = FLEXIO,
.SDAPinIndex = 0,
.SCLPinIndex = 1,
.shifterIndex = {0,1},
.timerIndex = {0,1}
};
flexio_i2c_master_config_t config = {
.enableInDoze = false,
.enableInDebug = true,
.enableFastAccess = false,
.baudRate_Bps = 100000
};
FLEXIO_I2C_MasterInit(base, &config, srcClock_Hz);
@endcode
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param masterConfig Pointer to flexio_i2c_master_config_t structure.
* @param srcClock_Hz FlexIO source clock in Hz.
* @retval kStatus_Success Initialization successful
* @retval kStatus_InvalidArgument The source clock exceed upper range limitation
*/
status_t FLEXIO_I2C_MasterInit(FLEXIO_I2C_Type *base, flexio_i2c_master_config_t *masterConfig, uint32_t srcClock_Hz);
/*!
* @brief De-initializes the FlexIO I2C master peripheral. Calling this API Resets the FlexIO I2C master
* shifer and timer config, module can't work unless the FLEXIO_I2C_MasterInit is called.
*
* @param base pointer to FLEXIO_I2C_Type structure.
*/
void FLEXIO_I2C_MasterDeinit(FLEXIO_I2C_Type *base);
/*!
* @brief Gets the default configuration to configure the FlexIO module. The configuration
* can be used directly for calling the FLEXIO_I2C_MasterInit().
*
* Example:
@code
flexio_i2c_master_config_t config;
FLEXIO_I2C_MasterGetDefaultConfig(&config);
@endcode
* @param masterConfig Pointer to flexio_i2c_master_config_t structure.
*/
void FLEXIO_I2C_MasterGetDefaultConfig(flexio_i2c_master_config_t *masterConfig);
/*!
* @brief Enables/disables the FlexIO module operation.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param enable Pass true to enable module, false does not have any effect.
*/
static inline void FLEXIO_I2C_MasterEnable(FLEXIO_I2C_Type *base, bool enable)
{
if (enable)
{
base->flexioBase->CTRL |= FLEXIO_CTRL_FLEXEN_MASK;
}
}
/* @} */
/*!
* @name Status
* @{
*/
/*!
* @brief Gets the FlexIO I2C master status flags.
*
* @param base Pointer to FLEXIO_I2C_Type structure
* @return Status flag, use status flag to AND #_flexio_i2c_master_status_flags can get the related status.
*/
uint32_t FLEXIO_I2C_MasterGetStatusFlags(FLEXIO_I2C_Type *base);
/*!
* @brief Clears the FlexIO I2C master status flags.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param mask Status flag.
* The parameter can be any combination of the following values:
* @arg kFLEXIO_I2C_RxFullFlag
* @arg kFLEXIO_I2C_ReceiveNakFlag
*/
void FLEXIO_I2C_MasterClearStatusFlags(FLEXIO_I2C_Type *base, uint32_t mask);
/*@}*/
/*!
* @name Interrupts
* @{
*/
/*!
* @brief Enables the FlexIO i2c master interrupt requests.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param mask Interrupt source.
* Currently only one interrupt request source:
* @arg kFLEXIO_I2C_TransferCompleteInterruptEnable
*/
void FLEXIO_I2C_MasterEnableInterrupts(FLEXIO_I2C_Type *base, uint32_t mask);
/*!
* @brief Disables the FlexIO I2C master interrupt requests.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param mask Interrupt source.
*/
void FLEXIO_I2C_MasterDisableInterrupts(FLEXIO_I2C_Type *base, uint32_t mask);
/*@}*/
/*!
* @name Bus Operations
* @{
*/
/*!
* @brief Sets the FlexIO I2C master transfer baudrate.
*
* @param base Pointer to FLEXIO_I2C_Type structure
* @param baudRate_Bps the baud rate value in HZ
* @param srcClock_Hz source clock in HZ
*/
void FLEXIO_I2C_MasterSetBaudRate(FLEXIO_I2C_Type *base, uint32_t baudRate_Bps, uint32_t srcClock_Hz);
/*!
* @brief Sends START + 7-bit address to the bus.
*
* @note This API should be called when the transfer configuration is ready to send a START signal
* and 7-bit address to the bus. This is a non-blocking API, which returns directly after the address
* is put into the data register but the address transfer is not finished on the bus. Ensure that
* the kFLEXIO_I2C_RxFullFlag status is asserted before calling this API.
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param address 7-bit address.
* @param direction transfer direction.
* This parameter is one of the values in flexio_i2c_direction_t:
* @arg kFLEXIO_I2C_Write: Transmit
* @arg kFLEXIO_I2C_Read: Receive
*/
void FLEXIO_I2C_MasterStart(FLEXIO_I2C_Type *base, uint8_t address, flexio_i2c_direction_t direction);
/*!
* @brief Sends the stop signal on the bus.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
*/
void FLEXIO_I2C_MasterStop(FLEXIO_I2C_Type *base);
/*!
* @brief Sends the repeated start signal on the bus.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
*/
void FLEXIO_I2C_MasterRepeatedStart(FLEXIO_I2C_Type *base);
/*!
* @brief Sends the stop signal when transfer is still on-going.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
*/
void FLEXIO_I2C_MasterAbortStop(FLEXIO_I2C_Type *base);
/*!
* @brief Configures the sent ACK/NAK for the following byte.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param enable True to configure send ACK, false configure to send NAK.
*/
void FLEXIO_I2C_MasterEnableAck(FLEXIO_I2C_Type *base, bool enable);
/*!
* @brief Sets the number of bytes to be transferred from a start signal to a stop signal.
*
* @note Call this API before a transfer begins because the timer generates a number of clocks according
* to the number of bytes that need to be transferred.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param count Number of bytes need to be transferred from a start signal to a re-start/stop signal
* @retval kStatus_Success Successfully configured the count.
* @retval kStatus_InvalidArgument Input argument is invalid.
*/
status_t FLEXIO_I2C_MasterSetTransferCount(FLEXIO_I2C_Type *base, uint8_t count);
/*!
* @brief Writes one byte of data to the I2C bus.
*
* @note This is a non-blocking API, which returns directly after the data is put into the
* data register but the data transfer is not finished on the bus. Ensure that
* the TxEmptyFlag is asserted before calling this API.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param data a byte of data.
*/
static inline void FLEXIO_I2C_MasterWriteByte(FLEXIO_I2C_Type *base, uint32_t data)
{
base->flexioBase->SHIFTBUFBBS[base->shifterIndex[0]] = data;
}
/*!
* @brief Reads one byte of data from the I2C bus.
*
* @note This is a non-blocking API, which returns directly after the data is read from the
* data register. Ensure that the data is ready in the register.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @return data byte read.
*/
static inline uint8_t FLEXIO_I2C_MasterReadByte(FLEXIO_I2C_Type *base)
{
return base->flexioBase->SHIFTBUFBIS[base->shifterIndex[1]];
}
/*!
* @brief Sends a buffer of data in bytes.
*
* @note This function blocks via polling until all bytes have been sent.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param txBuff The data bytes to send.
* @param txSize The number of data bytes to send.
* @retval kStatus_Success Successfully write data.
* @retval kStatus_FLEXIO_I2C_Nak Receive NAK during writing data.
*/
status_t FLEXIO_I2C_MasterWriteBlocking(FLEXIO_I2C_Type *base, const uint8_t *txBuff, uint8_t txSize);
/*!
* @brief Receives a buffer of bytes.
*
* @note This function blocks via polling until all bytes have been received.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param rxBuff The buffer to store the received bytes.
* @param rxSize The number of data bytes to be received.
*/
void FLEXIO_I2C_MasterReadBlocking(FLEXIO_I2C_Type *base, uint8_t *rxBuff, uint8_t rxSize);
/*!
* @brief Performs a master polling transfer on the I2C bus.
*
* @note The API does not return until the transfer succeeds or fails due
* to receiving NAK.
*
* @param base pointer to FLEXIO_I2C_Type structure.
* @param xfer pointer to flexio_i2c_master_transfer_t structure.
* @return status of status_t.
*/
status_t FLEXIO_I2C_MasterTransferBlocking(FLEXIO_I2C_Type *base, flexio_i2c_master_transfer_t *xfer);
/*@}*/
/*Transactional APIs*/
/*!
* @name Transactional
* @{
*/
/*!
* @brief Initializes the I2C handle which is used in transactional functions.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param handle Pointer to flexio_i2c_master_handle_t structure to store the transfer state.
* @param callback Pointer to user callback function.
* @param userData User param passed to the callback function.
* @retval kStatus_Success Successfully create the handle.
* @retval kStatus_OutOfRange The FlexIO type/handle/isr table out of range.
*/
status_t FLEXIO_I2C_MasterTransferCreateHandle(FLEXIO_I2C_Type *base,
flexio_i2c_master_handle_t *handle,
flexio_i2c_master_transfer_callback_t callback,
void *userData);
/*!
* @brief Performs a master interrupt non-blocking transfer on the I2C bus.
*
* @note The API returns immediately after the transfer initiates.
* Call FLEXIO_I2C_MasterGetTransferCount to poll the transfer status to check whether
* the transfer is finished. If the return status is not kStatus_FLEXIO_I2C_Busy, the transfer
* is finished.
*
* @param base Pointer to FLEXIO_I2C_Type structure
* @param handle Pointer to flexio_i2c_master_handle_t structure which stores the transfer state
* @param xfer pointer to flexio_i2c_master_transfer_t structure
* @retval kStatus_Success Successfully start a transfer.
* @retval kStatus_FLEXIO_I2C_Busy FlexIO I2C is not idle, is running another transfer.
*/
status_t FLEXIO_I2C_MasterTransferNonBlocking(FLEXIO_I2C_Type *base,
flexio_i2c_master_handle_t *handle,
flexio_i2c_master_transfer_t *xfer);
/*!
* @brief Gets the master transfer status during a interrupt non-blocking transfer.
*
* @param base Pointer to FLEXIO_I2C_Type structure.
* @param handle Pointer to flexio_i2c_master_handle_t structure which stores the transfer state.
* @param count Number of bytes transferred so far by the non-blocking transaction.
* @retval kStatus_InvalidArgument count is Invalid.
* @retval kStatus_Success Successfully return the count.
*/
status_t FLEXIO_I2C_MasterTransferGetCount(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle, size_t *count);
/*!
* @brief Aborts an interrupt non-blocking transfer early.
*
* @note This API can be called at any time when an interrupt non-blocking transfer initiates
* to abort the transfer early.
*
* @param base Pointer to FLEXIO_I2C_Type structure
* @param handle Pointer to flexio_i2c_master_handle_t structure which stores the transfer state
*/
void FLEXIO_I2C_MasterTransferAbort(FLEXIO_I2C_Type *base, flexio_i2c_master_handle_t *handle);
/*!
* @brief Master interrupt handler.
*
* @param i2cType Pointer to FLEXIO_I2C_Type structure
* @param i2cHandle Pointer to flexio_i2c_master_transfer_t structure
*/
void FLEXIO_I2C_MasterTransferHandleIRQ(void *i2cType, void *i2cHandle);
/*@}*/
#if defined(__cplusplus)
}
#endif /*_cplusplus*/
/*@}*/
#endif /*_FSL_FLEXIO_I2C_MASTER_H_*/