247 lines
11 KiB
C
247 lines
11 KiB
C
/***********************************************************************************************************************
|
|
* Copyright [2020-2023] Renesas Electronics Corporation and/or its affiliates. All Rights Reserved.
|
|
*
|
|
* This software and documentation are supplied by Renesas Electronics America Inc. and may only be used with products
|
|
* of Renesas Electronics Corp. and its affiliates ("Renesas"). No other uses are authorized. Renesas products are
|
|
* sold pursuant to Renesas terms and conditions of sale. Purchasers are solely responsible for the selection and use
|
|
* of Renesas products and Renesas assumes no liability. No license, express or implied, to any intellectual property
|
|
* right is granted by Renesas. This software is protected under all applicable laws, including copyright laws. Renesas
|
|
* reserves the right to change or discontinue this software and/or this documentation. THE SOFTWARE AND DOCUMENTATION
|
|
* IS DELIVERED TO YOU "AS IS," AND RENESAS MAKES NO REPRESENTATIONS OR WARRANTIES, AND TO THE FULLEST EXTENT
|
|
* PERMISSIBLE UNDER APPLICABLE LAW, DISCLAIMS ALL WARRANTIES, WHETHER EXPLICITLY OR IMPLICITLY, INCLUDING WARRANTIES
|
|
* OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE, AND NONINFRINGEMENT, WITH RESPECT TO THE SOFTWARE OR
|
|
* DOCUMENTATION. RENESAS SHALL HAVE NO LIABILITY ARISING OUT OF ANY SECURITY VULNERABILITY OR BREACH. TO THE MAXIMUM
|
|
* EXTENT PERMITTED BY LAW, IN NO EVENT WILL RENESAS BE LIABLE TO YOU IN CONNECTION WITH THE SOFTWARE OR DOCUMENTATION
|
|
* (OR ANY PERSON OR ENTITY CLAIMING RIGHTS DERIVED FROM YOU) FOR ANY LOSS, DAMAGES, OR CLAIMS WHATSOEVER, INCLUDING,
|
|
* WITHOUT LIMITATION, ANY DIRECT, CONSEQUENTIAL, SPECIAL, INDIRECT, PUNITIVE, OR INCIDENTAL DAMAGES; ANY LOST PROFITS,
|
|
* OTHER ECONOMIC DAMAGE, PROPERTY DAMAGE, OR PERSONAL INJURY; AND EVEN IF RENESAS HAS BEEN ADVISED OF THE POSSIBILITY
|
|
* OF SUCH LOSS, DAMAGES, CLAIMS OR COSTS.
|
|
**********************************************************************************************************************/
|
|
|
|
/***********************************************************************************************************************
|
|
* Includes <System Includes> , "Project Includes"
|
|
**********************************************************************************************************************/
|
|
|
|
#include "r_ioport.h"
|
|
#include "bsp_cfg.h"
|
|
#include "bsp_pin_cfg.h"
|
|
|
|
#include "board_sdram.h"
|
|
|
|
/***********************************************************************************************************************
|
|
* Macro definitions
|
|
**********************************************************************************************************************/
|
|
|
|
/* SDRAM size, in bytes */
|
|
#define SDRAM_SIZE (64 * 1024 * 1024)
|
|
|
|
/*
|
|
* Set ACTIVE-to-PRECHARGE command (tRAS) timing
|
|
* e.g. tRAS = 42ns -> 6cycles are needed at SDCLK 120MHz
|
|
* tRAS = 37ns -> 5cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_TRAS (6U)
|
|
|
|
/*
|
|
* Set ACTIVE-to-READ or WRITE delay tRCD (tRCD) timing
|
|
* e.g. tRCD = 18ns -> 3cycles are needed at SDCLK 120MHz
|
|
* tRCD = 15ns -> 2cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_TRCD (3U)
|
|
|
|
/*
|
|
* Set PRECHARGE command period (tRP) timing
|
|
* e.g. tRP = 18ns -> 3cycles are needed at SDCLK 120MHz
|
|
* tRP = 15ns -> 2cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_TRP (3U)
|
|
|
|
/*
|
|
* Set WRITE recovery time (tWR) timing
|
|
* e.g. tWR = 1CLK + 6ns -> 2cycles are needed at SDCLK 120MHz
|
|
* tWR = 1CLK + 7ns -> 2cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_TWR (2U)
|
|
|
|
/*
|
|
* Set CAS (READ) latency (CL) timing
|
|
* e.g. CL = 18ns -> 3cycles are needed at SDCLK 120MHz
|
|
* e.g. CL = 15ns -> 2cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_CL (3U)
|
|
|
|
/*
|
|
* Set AUTO REFRESH period (tRFC) timing
|
|
* e.g. tRFC = 60nS -> 8cycles are needed at SDCLK 120MHz
|
|
* tRFC = 66nS -> 8cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_TRFC (8U)
|
|
|
|
/*
|
|
* Set Average Refresh period
|
|
* e.g. tREF = 64ms/8192rows -> 7.8125us/each row. 937cycles are needed at SDCLK 120MHz
|
|
*/
|
|
#define BSP_PRV_SDRAM_REF_CMD_INTERVAL (937U)
|
|
|
|
/*
|
|
* Set Auto-Refresh issue times in initialization sequence needed for SDRAM device
|
|
* Typical SDR SDRAM device needs twice of Auto-Refresh command issue
|
|
*/
|
|
#define BSP_PRV_SDRAM_SDIR_REF_TIMES (2U)
|
|
|
|
/*
|
|
* Set RAW address offset
|
|
* Available settings are
|
|
* 8 : 8-bit
|
|
* 9 : 9-bit
|
|
* 10 : 10-bit
|
|
* 11 : 11-bit
|
|
*/
|
|
#define BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET (9U)
|
|
|
|
/*
|
|
* Select endian mode for SDRAM address space
|
|
* 0 : Endian of SDRAM address space is the same as the endian of operating mode
|
|
* 1 : Endian of SDRAM address space is not the endian of operating mode
|
|
*/
|
|
#define BSP_PRV_SDRAM_ENDIAN_MODE (0U)
|
|
|
|
/*
|
|
* Select access mode
|
|
* Typically Continuous access should be enabled to get better SDRAM bandwidth
|
|
* 0: Continuous access is disabled
|
|
* 1: Continuous access is enabled
|
|
*/
|
|
#define BSP_PRV_SDRAM_CONTINUOUS_ACCESSMODE (1U)
|
|
|
|
/*
|
|
* Select bus width
|
|
* 0: 16-bit
|
|
* 1: 32-bit
|
|
* 2: 8-bit
|
|
*/
|
|
#define BSP_PRV_SDRAM_BUS_WIDTH (0U)
|
|
|
|
#if ((BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET != 8U) && (BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET != 9U) \
|
|
&& (BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET != 10U) && (BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET > 11U))
|
|
#error "BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET must be either of 8,9,10 or 11"
|
|
#endif
|
|
|
|
#if ((BSP_PRV_SDRAM_BUS_WIDTH != 0) && (BSP_PRV_SDRAM_BUS_WIDTH != 1U) && (BSP_PRV_SDRAM_BUS_WIDTH != 2U))
|
|
#error "BSP_PRV_SDRAM_BUS_WIDTH must be either of 0(16-bit) or 1(32-bit) or 2(8-bit)"
|
|
#endif
|
|
|
|
#if ((BSP_PRV_SDRAM_ENDIAN_MODE != 0) && (BSP_PRV_SDRAM_ENDIAN_MODE != 1))
|
|
#error \
|
|
"BSP_PRV_SDRAM_ENDIAN_MODE must be either of 0(same endian as operating mode) or 2(another endian against operating mode)"
|
|
#endif
|
|
|
|
#if ((BSP_PRV_SDRAM_CONTINUOUS_ACCESSMODE != 0) && (BSP_PRV_SDRAM_CONTINUOUS_ACCESSMODE != 1))
|
|
#error \
|
|
"BSP_PRV_SDRAM_CONTINUOUS_ACCESSMODE must be either of 0(continuous access is disabled) or 1(continuous access is enabled)"
|
|
#endif
|
|
|
|
#define BSP_PRV_SDRAM_MR_WB_SINGLE_LOC_ACC (1U) /* MR.M9 : Single Location Access */
|
|
#define BSP_PRV_SDRAM_MR_OP_MODE (0U) /* MR.M8:M7 : Standard Operation */
|
|
#define BSP_PRV_SDRAM_MR_BT_SEQUENCTIAL (0U) /* MR.M3 Burst Type : Sequential */
|
|
#define BSP_PRV_SDRAM_MR_BURST_LENGTH (0U) /* MR.M2:M0 Burst Length: 0(1 burst) */
|
|
|
|
/***********************************************************************************************************************
|
|
* Typedef definitions
|
|
**********************************************************************************************************************/
|
|
|
|
/***********************************************************************************************************************
|
|
* Exported global variables (to be accessed by other files)
|
|
**********************************************************************************************************************/
|
|
|
|
/***********************************************************************************************************************
|
|
* Private global variables and functions
|
|
**********************************************************************************************************************/
|
|
|
|
void bsp_sdram_init (void)
|
|
{
|
|
/** Setting for SDRAM initialization sequence */
|
|
#if (BSP_PRV_SDRAM_TRP < 3)
|
|
R_BUS->SDRAM.SDIR_b.PRC = 3U;
|
|
#else
|
|
R_BUS->SDRAM.SDIR_b.PRC = BSP_PRV_SDRAM_TRP - 3U;
|
|
#endif
|
|
|
|
while (R_BUS->SDRAM.SDSR)
|
|
{
|
|
/* According to h/w maual, need to confirm that all the status bits in SDSR are 0 before SDIR modification. */
|
|
}
|
|
|
|
R_BUS->SDRAM.SDIR_b.ARFC = BSP_PRV_SDRAM_SDIR_REF_TIMES;
|
|
|
|
while (R_BUS->SDRAM.SDSR)
|
|
{
|
|
/* According to h/w maual, need to confirm that all the status bits in SDSR are 0 before SDIR modification. */
|
|
}
|
|
|
|
#if (BSP_PRV_SDRAM_TRFC < 3)
|
|
R_BUS->SDRAM.SDIR_b.ARFI = 0U;
|
|
#else
|
|
R_BUS->SDRAM.SDIR_b.ARFI = BSP_PRV_SDRAM_TRFC - 3U;
|
|
#endif
|
|
|
|
while (R_BUS->SDRAM.SDSR)
|
|
{
|
|
/* According to h/w maual, need to confirm that all the status bits in SDSR are 0 before SDICR modification. */
|
|
}
|
|
|
|
/** Start SDRAM initialization sequence.
|
|
* Following operation is automatically done when set SDICR.INIRQ bit.
|
|
* Perform a PRECHARGE ALL command and wait at least tRP time.
|
|
* Issue an AUTO REFRESH command and wait at least tRFC time.
|
|
* Issue an AUTO REFRESH command and wait at least tRFC time.
|
|
*/
|
|
R_BUS->SDRAM.SDICR_b.INIRQ = 1U;
|
|
while (R_BUS->SDRAM.SDSR_b.INIST)
|
|
{
|
|
/* Wait the end of initialization sequence. */
|
|
}
|
|
|
|
/** Setting for SDRAM controller */
|
|
R_BUS->SDRAM.SDCCR_b.BSIZE = BSP_PRV_SDRAM_BUS_WIDTH; /* set SDRAM bus width */
|
|
R_BUS->SDRAM.SDAMOD_b.BE = BSP_PRV_SDRAM_CONTINUOUS_ACCESSMODE; /* enable continuous access */
|
|
R_BUS->SDRAM.SDCMOD_b.EMODE = BSP_PRV_SDRAM_ENDIAN_MODE; /* set endian mode for SDRAM address space */
|
|
|
|
while (R_BUS->SDRAM.SDSR)
|
|
{
|
|
/* According to h/w maual, need to confirm that all the status bits in SDSR are 0 before SDMOD modification. */
|
|
}
|
|
|
|
/** Using LMR command, program the mode register */
|
|
R_BUS->SDRAM.SDMOD = ((((uint16_t) (BSP_PRV_SDRAM_MR_WB_SINGLE_LOC_ACC << 9) |
|
|
(uint16_t) (BSP_PRV_SDRAM_MR_OP_MODE << 7)) |
|
|
(uint16_t) (BSP_PRV_SDRAM_CL << 4)) |
|
|
(uint16_t) (BSP_PRV_SDRAM_MR_BT_SEQUENCTIAL << 3)) |
|
|
(uint16_t) (BSP_PRV_SDRAM_MR_BURST_LENGTH << 0);
|
|
|
|
/** wait at least tMRD time */
|
|
while (R_BUS->SDRAM.SDSR_b.MRSST)
|
|
{
|
|
/* Wait until Mode Register setting done. */
|
|
}
|
|
|
|
/** Set timing parameters for SDRAM */
|
|
R_BUS->SDRAM.SDTR_b.RAS = BSP_PRV_SDRAM_TRAS - 1U; /* set ACTIVE-to-PRECHARGE command cycles*/
|
|
R_BUS->SDRAM.SDTR_b.RCD = BSP_PRV_SDRAM_TRCD - 1U; /* set ACTIVE to READ/WRITE delay cycles */
|
|
R_BUS->SDRAM.SDTR_b.RP = BSP_PRV_SDRAM_TRP - 1U; /* set PRECHARGE command period cycles */
|
|
R_BUS->SDRAM.SDTR_b.WR = BSP_PRV_SDRAM_TWR - 1U; /* set write recovery cycles */
|
|
R_BUS->SDRAM.SDTR_b.CL = BSP_PRV_SDRAM_CL; /* set SDRAM column latency cycles */
|
|
|
|
/** Set row address offset for target SDRAM */
|
|
R_BUS->SDRAM.SDADR_b.MXC = BSP_PRV_SDRAM_SDADR_ROW_ADDR_OFFSET - 8U;
|
|
|
|
R_BUS->SDRAM.SDRFCR_b.REFW = (uint16_t) (BSP_PRV_SDRAM_TRFC - 1U); /* set Auto-Refresh issuing cycle */
|
|
R_BUS->SDRAM.SDRFCR_b.RFC = BSP_PRV_SDRAM_REF_CMD_INTERVAL - 1U; /* set Auto-Refresh period */
|
|
|
|
/** Start Auto-refresh */
|
|
R_BUS->SDRAM.SDRFEN_b.RFEN = 1U;
|
|
|
|
/** Enable SDRAM access */
|
|
R_BUS->SDRAM.SDCCR_b.EXENB = 1U;
|
|
}
|