libs/rt-thread
libs
/
rt-thread
4
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
rt-thread/bsp/stm32f40x/Libraries/STM32F4xx_StdPeriph_Driver/src/stm32f4xx_exti.c

307 lines
9.7 KiB
C
Raw Blame History

/**
******************************************************************************
* @file stm32f4xx_exti.c
* @author MCD Application Team
* @version V1.0.0
* @date 30-September-2011
* @brief This file provides firmware functions to manage the following
* functionalities of the EXTI peripheral:
* - Initialization and Configuration
* - Interrupts and flags management
*
* @verbatim
*
* ===================================================================
* EXTI features
* ===================================================================
*
* External interrupt/event lines are mapped as following:
* 1- All available GPIO pins are connected to the 16 external
* interrupt/event lines from EXTI0 to EXTI15.
* 2- EXTI line 16 is connected to the PVD Output
* 3- EXTI line 17 is connected to the RTC Alarm event
* 4- EXTI line 18 is connected to the USB OTG FS Wakeup from suspend event
* 5- EXTI line 19 is connected to the Ethernet Wakeup event
* 6- EXTI line 20 is connected to the USB OTG HS (configured in FS) Wakeup event
* 7- EXTI line 21 is connected to the RTC Tamper and Time Stamp events
* 8- EXTI line 22 is connected to the RTC Wakeup event
*
* ===================================================================
* How to use this driver
* ===================================================================
*
* In order to use an I/O pin as an external interrupt source, follow
* steps below:
* 1- Configure the I/O in input mode using GPIO_Init()
* 2- Select the input source pin for the EXTI line using SYSCFG_EXTILineConfig()
* 3- Select the mode(interrupt, event) and configure the trigger
* selection (Rising, falling or both) using EXTI_Init()
* 4- Configure NVIC IRQ channel mapped to the EXTI line using NVIC_Init()
*
* @note SYSCFG APB clock must be enabled to get write access to SYSCFG_EXTICRx
* registers using RCC_APB2PeriphClockCmd(RCC_APB2Periph_SYSCFG, ENABLE);
*
* @endverbatim
*
******************************************************************************
* @attention
*
* THE PRESENT FIRMWARE WHICH IS FOR GUIDANCE ONLY AIMS AT PROVIDING CUSTOMERS
* WITH CODING INFORMATION REGARDING THEIR PRODUCTS IN ORDER FOR THEM TO SAVE
* TIME. AS A RESULT, STMICROELECTRONICS SHALL NOT BE HELD LIABLE FOR ANY
* DIRECT, INDIRECT OR CONSEQUENTIAL DAMAGES WITH RESPECT TO ANY CLAIMS ARISING
* FROM THE CONTENT OF SUCH FIRMWARE AND/OR THE USE MADE BY CUSTOMERS OF THE
* CODING INFORMATION CONTAINED HEREIN IN CONNECTION WITH THEIR PRODUCTS.
*
* <h2><center>&copy; COPYRIGHT 2011 STMicroelectronics</center></h2>
******************************************************************************
*/
/* Includes ------------------------------------------------------------------*/
#include "stm32f4xx_exti.h"
/** @addtogroup STM32F4xx_StdPeriph_Driver
* @{
*/
/** @defgroup EXTI
* @brief EXTI driver modules
* @{
*/
/* Private typedef -----------------------------------------------------------*/
/* Private define ------------------------------------------------------------*/
#define EXTI_LINENONE ((uint32_t)0x00000) /* No interrupt selected */
/* Private macro -------------------------------------------------------------*/
/* Private variables ---------------------------------------------------------*/
/* Private function prototypes -----------------------------------------------*/
/* Private functions ---------------------------------------------------------*/
/** @defgroup EXTI_Private_Functions
* @{
*/
/** @defgroup EXTI_Group1 Initialization and Configuration functions
* @brief Initialization and Configuration functions
*
@verbatim
===============================================================================
Initialization and Configuration functions
===============================================================================
@endverbatim
* @{
*/
/**
* @brief Deinitializes the EXTI peripheral registers to their default reset values.
* @param None
* @retval None
*/
void EXTI_DeInit(void)
{
EXTI->IMR = 0x00000000;
EXTI->EMR = 0x00000000;
EXTI->RTSR = 0x00000000;
EXTI->FTSR = 0x00000000;
EXTI->PR = 0x007FFFFF;
}
/**
* @brief Initializes the EXTI peripheral according to the specified
* parameters in the EXTI_InitStruct.
* @param EXTI_InitStruct: pointer to a EXTI_InitTypeDef structure
* that contains the configuration information for the EXTI peripheral.
* @retval None
*/
void EXTI_Init(EXTI_InitTypeDef* EXTI_InitStruct)
{
uint32_t tmp = 0;
/* Check the parameters */
assert_param(IS_EXTI_MODE(EXTI_InitStruct->EXTI_Mode));
assert_param(IS_EXTI_TRIGGER(EXTI_InitStruct->EXTI_Trigger));
assert_param(IS_EXTI_LINE(EXTI_InitStruct->EXTI_Line));
assert_param(IS_FUNCTIONAL_STATE(EXTI_InitStruct->EXTI_LineCmd));
tmp = (uint32_t)EXTI_BASE;
if (EXTI_InitStruct->EXTI_LineCmd != DISABLE)
{
/* Clear EXTI line configuration */
EXTI->IMR &= ~EXTI_InitStruct->EXTI_Line;
EXTI->EMR &= ~EXTI_InitStruct->EXTI_Line;
tmp += EXTI_InitStruct->EXTI_Mode;
*(__IO uint32_t *) tmp |= EXTI_InitStruct->EXTI_Line;
/* Clear Rising Falling edge configuration */
EXTI->RTSR &= ~EXTI_InitStruct->EXTI_Line;
EXTI->FTSR &= ~EXTI_InitStruct->EXTI_Line;
/* Select the trigger for the selected external interrupts */
if (EXTI_InitStruct->EXTI_Trigger == EXTI_Trigger_Rising_Falling)
{
/* Rising Falling edge */
EXTI->RTSR |= EXTI_InitStruct->EXTI_Line;
EXTI->FTSR |= EXTI_InitStruct->EXTI_Line;
}
else
{
tmp = (uint32_t)EXTI_BASE;
tmp += EXTI_InitStruct->EXTI_Trigger;
*(__IO uint32_t *) tmp |= EXTI_InitStruct->EXTI_Line;
}
}
else
{
tmp += EXTI_InitStruct->EXTI_Mode;
/* Disable the selected external lines */
*(__IO uint32_t *) tmp &= ~EXTI_InitStruct->EXTI_Line;
}
}
/**
* @brief Fills each EXTI_InitStruct member with its reset value.
* @param EXTI_InitStruct: pointer to a EXTI_InitTypeDef structure which will
* be initialized.
* @retval None
*/
void EXTI_StructInit(EXTI_InitTypeDef* EXTI_InitStruct)
{
EXTI_InitStruct->EXTI_Line = EXTI_LINENONE;
EXTI_InitStruct->EXTI_Mode = EXTI_Mode_Interrupt;
EXTI_InitStruct->EXTI_Trigger = EXTI_Trigger_Falling;
EXTI_InitStruct->EXTI_LineCmd = DISABLE;
}
/**
* @brief Generates a Software interrupt on selected EXTI line.
* @param EXTI_Line: specifies the EXTI line on which the software interrupt
* will be generated.
* This parameter can be any combination of EXTI_Linex where x can be (0..22)
* @retval None
*/
void EXTI_GenerateSWInterrupt(uint32_t EXTI_Line)
{
/* Check the parameters */
assert_param(IS_EXTI_LINE(EXTI_Line));
EXTI->SWIER |= EXTI_Line;
}
/**
* @}
*/
/** @defgroup EXTI_Group2 Interrupts and flags management functions
* @brief Interrupts and flags management functions
*
@verbatim
===============================================================================
Interrupts and flags management functions
===============================================================================
@endverbatim
* @{
*/
/**
* @brief Checks whether the specified EXTI line flag is set or not.
* @param EXTI_Line: specifies the EXTI line flag to check.
* This parameter can be EXTI_Linex where x can be(0..22)
* @retval The new state of EXTI_Line (SET or RESET).
*/
FlagStatus EXTI_GetFlagStatus(uint32_t EXTI_Line)
{
FlagStatus bitstatus = RESET;
/* Check the parameters */
assert_param(IS_GET_EXTI_LINE(EXTI_Line));
if ((EXTI->PR & EXTI_Line) != (uint32_t)RESET)
{
bitstatus = SET;
}
else
{
bitstatus = RESET;
}
return bitstatus;
}
/**
* @brief Clears the EXTI's line pending flags.
* @param EXTI_Line: specifies the EXTI lines flags to clear.
* This parameter can be any combination of EXTI_Linex where x can be (0..22)
* @retval None
*/
void EXTI_ClearFlag(uint32_t EXTI_Line)
{
/* Check the parameters */
assert_param(IS_EXTI_LINE(EXTI_Line));
EXTI->PR = EXTI_Line;
}
/**
* @brief Checks whether the specified EXTI line is asserted or not.
* @param EXTI_Line: specifies the EXTI line to check.
* This parameter can be EXTI_Linex where x can be(0..22)
* @retval The new state of EXTI_Line (SET or RESET).
*/
ITStatus EXTI_GetITStatus(uint32_t EXTI_Line)
{
ITStatus bitstatus = RESET;
uint32_t enablestatus = 0;
/* Check the parameters */
assert_param(IS_GET_EXTI_LINE(EXTI_Line));
enablestatus = EXTI->IMR & EXTI_Line;
if (((EXTI->PR & EXTI_Line) != (uint32_t)RESET) && (enablestatus != (uint32_t)RESET))
{
bitstatus = SET;
}
else
{
bitstatus = RESET;
}
return bitstatus;
}
/**
* @brief Clears the EXTI's line pending bits.
* @param EXTI_Line: specifies the EXTI lines to clear.
* This parameter can be any combination of EXTI_Linex where x can be (0..22)
* @retval None
*/
void EXTI_ClearITPendingBit(uint32_t EXTI_Line)
{
/* Check the parameters */
assert_param(IS_EXTI_LINE(EXTI_Line));
EXTI->PR = EXTI_Line;
}
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/**
* @}
*/
/******************* (C) COPYRIGHT 2011 STMicroelectronics *****END OF FILE****/
View Git Blame Copy Permalink