8d90cfadf0
1. Make up sources and bugfix. 2. Add nu_gpio_pin_get. 3. Add PM operator in USB host driver. 4. Support NUC980 stage 1 and add nk-980iot board.
134 lines
4.1 KiB
Plaintext
134 lines
4.1 KiB
Plaintext
menu "Hardware Drivers Config"
|
|
|
|
menu "On-chip Peripheral Drivers"
|
|
source "$BSP_DIR/../libraries/nuc980/rtt_port/Kconfig"
|
|
endmenu
|
|
|
|
menu "On-board Peripheral Drivers"
|
|
|
|
config BSP_USING_CONSOLE
|
|
bool "Enable UART0 for RTT Console(uart0)"
|
|
select BSP_USING_UART
|
|
select BSP_USING_UART0
|
|
default y
|
|
|
|
config BOARD_USING_IP101GR
|
|
bool "Enable ethernet phy supporting(over emac/mdio)"
|
|
select BSP_USING_EMAC
|
|
default n
|
|
|
|
|
|
config BOARD_USING_NAU8822L
|
|
bool "NAU8822L Audio Codec supporting(over i2s, i2c2)"
|
|
select NU_PKG_USING_NAU8822L
|
|
select BSP_USING_I2C0
|
|
select BSP_USING_I2S
|
|
select BSP_USING_I2S0
|
|
default n
|
|
|
|
config BOARD_USING_STORAGE_SDCARD
|
|
bool "SDCARD supporting(over sdh1)"
|
|
select BSP_USING_SDH
|
|
select BSP_USING_SDH1
|
|
default y
|
|
|
|
config BOARD_USING_STORAGE_SPIFLASH
|
|
bool "SPIFLASH supporting(over qspi0)"
|
|
select BSP_USING_QSPI
|
|
select BSP_USING_QSPI0
|
|
default y
|
|
|
|
choice
|
|
prompt "Select FS/HS USB Ports"
|
|
|
|
config BOARD_USING_USB_NONE
|
|
bool "Without any USB function"
|
|
help
|
|
Choose this option if you need not USB functions.
|
|
|
|
config BOARD_USING_HSUSBD
|
|
select BSP_USING_HSUSBD
|
|
bool "Enable HSUSBD(over USB2.0)"
|
|
help
|
|
Choose this option if you need HSUSBD function mode.
|
|
|
|
config BOARD_USING_HSUSBD_USBH
|
|
select BSP_USING_USBH
|
|
select BSP_USING_HSUSBD
|
|
bool "Enable HSUSBD(over USB2.0) and USBH(over USB1.1)"
|
|
help
|
|
Choose this option if you need HSUSBD and USBH function mode at the same time.
|
|
|
|
config BOARD_USING_HSUSBH
|
|
select BSP_USING_HSUSBH
|
|
bool "Enable HSUSBH(over USB2.0)"
|
|
help
|
|
Choose this option if you need HSUSBH function mode.
|
|
|
|
config BOARD_USING_HSUSBH_USBD
|
|
select BSP_USING_HSUSBH
|
|
select BSP_USING_USBD
|
|
bool "Enable HSUSBH(over USB2.0) and USBD(over USB1.1)"
|
|
help
|
|
Choose this option if you need HSUSBH and USBD function mode at the same time.
|
|
|
|
config BOARD_USING_HSOTG
|
|
select BSP_USING_HSOTG
|
|
bool "Enable HSOTG(over USB2.0)"
|
|
help
|
|
Choose this option if you need HSOTG function mode.
|
|
|
|
endchoice
|
|
|
|
endmenu
|
|
|
|
menu "Board extended module drivers"
|
|
|
|
config BOARD_USING_MAX31875
|
|
bool "MAX31875 Temperature sensor(over i2c1)"
|
|
select NU_PKG_USING_MAX31875
|
|
select BSP_USING_I2C1
|
|
default n
|
|
|
|
config BOARD_USING_LCD_ILI9341
|
|
bool "LCD ILI9341 (over spi0)"
|
|
select NU_PKG_USING_ILI9341
|
|
select NU_PKG_USING_ILI9341_SPI
|
|
select BSP_USING_SPI0
|
|
default n
|
|
|
|
if BOARD_USING_LCD_ILI9341
|
|
|
|
config BOARD_USING_ILI9341_PIN_BACKLIGHT
|
|
int "Specify the pin index of backlight pin index"
|
|
range 0 127
|
|
default 103
|
|
|
|
config BOARD_USING_ILI9341_PIN_RESET
|
|
int "Specify the pin index of reset pin index"
|
|
range 0 127
|
|
default 90
|
|
|
|
config BOARD_USING_ILI9341_PIN_DC
|
|
int "Specify the pin index of data&command switching"
|
|
range 0 127
|
|
default 89
|
|
|
|
endif
|
|
|
|
config BOARD_USING_ESP8266
|
|
bool "ESP8266 Wi-Fi module supporting(over uart1)"
|
|
select BSP_USING_UART
|
|
select BSP_USING_UART1
|
|
select BSP_USING_UART1_RX_DMA
|
|
select BSP_USING_UART1_TX_DMA
|
|
select PKG_USING_AT_DEVICE
|
|
select AT_DEVICE_USING_ESP8266
|
|
select AT_DEVICE_ESP8266_INIT_ASYN
|
|
default n
|
|
|
|
endmenu
|
|
|
|
|
|
endmenu
|