340 lines
8.7 KiB
C
340 lines
8.7 KiB
C
/* USER CODE BEGIN Header */
|
|
/**
|
|
******************************************************************************
|
|
* @file : main.c
|
|
* @brief : Main program body
|
|
******************************************************************************
|
|
* @attention
|
|
*
|
|
* <h2><center>© Copyright (c) 2019 STMicroelectronics.
|
|
* All rights reserved.</center></h2>
|
|
*
|
|
* This software component is licensed by ST under BSD 3-Clause license,
|
|
* the "License"; You may not use this file except in compliance with the
|
|
* License. You may obtain a copy of the License at:
|
|
* opensource.org/licenses/BSD-3-Clause
|
|
*
|
|
******************************************************************************
|
|
*/
|
|
/* USER CODE END Header */
|
|
|
|
/* Includes ------------------------------------------------------------------*/
|
|
#include "main.h"
|
|
|
|
/* Private includes ----------------------------------------------------------*/
|
|
/* USER CODE BEGIN Includes */
|
|
|
|
/* USER CODE END Includes */
|
|
|
|
/* Private typedef -----------------------------------------------------------*/
|
|
/* USER CODE BEGIN PTD */
|
|
|
|
/* USER CODE END PTD */
|
|
|
|
/* Private define ------------------------------------------------------------*/
|
|
/* USER CODE BEGIN PD */
|
|
|
|
/* USER CODE END PD */
|
|
|
|
/* Private macro -------------------------------------------------------------*/
|
|
/* USER CODE BEGIN PM */
|
|
|
|
/* USER CODE END PM */
|
|
|
|
/* Private variables ---------------------------------------------------------*/
|
|
|
|
ETH_HandleTypeDef heth;
|
|
|
|
UART_HandleTypeDef huart5;
|
|
UART_HandleTypeDef huart1;
|
|
|
|
/* USER CODE BEGIN PV */
|
|
|
|
/* USER CODE END PV */
|
|
|
|
/* Private function prototypes -----------------------------------------------*/
|
|
void SystemClock_Config(void);
|
|
static void MX_GPIO_Init(void);
|
|
static void MX_USART1_UART_Init(void);
|
|
static void MX_ETH_Init(void);
|
|
static void MX_UART5_Init(void);
|
|
/* USER CODE BEGIN PFP */
|
|
|
|
/* USER CODE END PFP */
|
|
|
|
/* Private user code ---------------------------------------------------------*/
|
|
/* USER CODE BEGIN 0 */
|
|
|
|
/* USER CODE END 0 */
|
|
|
|
/**
|
|
* @brief The application entry point.
|
|
* @retval int
|
|
*/
|
|
int main(void)
|
|
{
|
|
/* USER CODE BEGIN 1 */
|
|
|
|
/* USER CODE END 1 */
|
|
|
|
/* MCU Configuration--------------------------------------------------------*/
|
|
|
|
/* Reset of all peripherals, Initializes the Flash interface and the Systick. */
|
|
HAL_Init();
|
|
|
|
/* USER CODE BEGIN Init */
|
|
|
|
/* USER CODE END Init */
|
|
|
|
/* Configure the system clock */
|
|
SystemClock_Config();
|
|
|
|
/* USER CODE BEGIN SysInit */
|
|
|
|
/* USER CODE END SysInit */
|
|
|
|
/* Initialize all configured peripherals */
|
|
MX_GPIO_Init();
|
|
MX_USART1_UART_Init();
|
|
MX_ETH_Init();
|
|
MX_UART5_Init();
|
|
/* USER CODE BEGIN 2 */
|
|
|
|
/* USER CODE END 2 */
|
|
|
|
/* Infinite loop */
|
|
/* USER CODE BEGIN WHILE */
|
|
while (1)
|
|
{
|
|
/* USER CODE END WHILE */
|
|
|
|
/* USER CODE BEGIN 3 */
|
|
}
|
|
/* USER CODE END 3 */
|
|
}
|
|
|
|
/**
|
|
* @brief System Clock Configuration
|
|
* @retval None
|
|
*/
|
|
void SystemClock_Config(void)
|
|
{
|
|
RCC_OscInitTypeDef RCC_OscInitStruct = {0};
|
|
RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
|
|
RCC_PeriphCLKInitTypeDef PeriphClkInitStruct = {0};
|
|
|
|
/** Configure LSE Drive Capability
|
|
*/
|
|
HAL_PWR_EnableBkUpAccess();
|
|
/** Configure the main internal regulator output voltage
|
|
*/
|
|
__HAL_RCC_PWR_CLK_ENABLE();
|
|
__HAL_PWR_VOLTAGESCALING_CONFIG(PWR_REGULATOR_VOLTAGE_SCALE1);
|
|
/** Initializes the CPU, AHB and APB busses clocks
|
|
*/
|
|
RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSI;
|
|
RCC_OscInitStruct.HSIState = RCC_HSI_ON;
|
|
RCC_OscInitStruct.HSICalibrationValue = RCC_HSICALIBRATION_DEFAULT;
|
|
RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
|
|
RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSI;
|
|
RCC_OscInitStruct.PLL.PLLM = 8;
|
|
RCC_OscInitStruct.PLL.PLLN = 216;
|
|
RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV2;
|
|
RCC_OscInitStruct.PLL.PLLQ = 2;
|
|
if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
/** Activate the Over-Drive mode
|
|
*/
|
|
if (HAL_PWREx_EnableOverDrive() != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
/** Initializes the CPU, AHB and APB busses clocks
|
|
*/
|
|
RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK
|
|
|RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;
|
|
RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;
|
|
RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;
|
|
RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV4;
|
|
RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV2;
|
|
|
|
if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_7) != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
PeriphClkInitStruct.PeriphClockSelection = RCC_PERIPHCLK_USART1|RCC_PERIPHCLK_UART5;
|
|
PeriphClkInitStruct.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK2;
|
|
PeriphClkInitStruct.Uart5ClockSelection = RCC_UART5CLKSOURCE_PCLK1;
|
|
if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInitStruct) != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
}
|
|
|
|
/**
|
|
* @brief ETH Initialization Function
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
static void MX_ETH_Init(void)
|
|
{
|
|
|
|
/* USER CODE BEGIN ETH_Init 0 */
|
|
|
|
/* USER CODE END ETH_Init 0 */
|
|
|
|
/* USER CODE BEGIN ETH_Init 1 */
|
|
|
|
/* USER CODE END ETH_Init 1 */
|
|
heth.Instance = ETH;
|
|
heth.Init.AutoNegotiation = ETH_AUTONEGOTIATION_ENABLE;
|
|
heth.Init.PhyAddress = DP83848_PHY_ADDRESS;
|
|
heth.Init.MACAddr[0] = 0x00;
|
|
heth.Init.MACAddr[1] = 0x80;
|
|
heth.Init.MACAddr[2] = 0xE1;
|
|
heth.Init.MACAddr[3] = 0x00;
|
|
heth.Init.MACAddr[4] = 0x00;
|
|
heth.Init.MACAddr[5] = 0x00;
|
|
heth.Init.RxMode = ETH_RXPOLLING_MODE;
|
|
heth.Init.ChecksumMode = ETH_CHECKSUM_BY_HARDWARE;
|
|
heth.Init.MediaInterface = ETH_MEDIA_INTERFACE_MII;
|
|
|
|
/* USER CODE BEGIN MACADDRESS */
|
|
|
|
/* USER CODE END MACADDRESS */
|
|
|
|
if (HAL_ETH_Init(&heth) != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
/* USER CODE BEGIN ETH_Init 2 */
|
|
|
|
/* USER CODE END ETH_Init 2 */
|
|
|
|
}
|
|
|
|
/**
|
|
* @brief UART5 Initialization Function
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
static void MX_UART5_Init(void)
|
|
{
|
|
|
|
/* USER CODE BEGIN UART5_Init 0 */
|
|
|
|
/* USER CODE END UART5_Init 0 */
|
|
|
|
/* USER CODE BEGIN UART5_Init 1 */
|
|
|
|
/* USER CODE END UART5_Init 1 */
|
|
huart5.Instance = UART5;
|
|
huart5.Init.BaudRate = 115200;
|
|
huart5.Init.WordLength = UART_WORDLENGTH_8B;
|
|
huart5.Init.StopBits = UART_STOPBITS_1;
|
|
huart5.Init.Parity = UART_PARITY_NONE;
|
|
huart5.Init.Mode = UART_MODE_TX_RX;
|
|
huart5.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
|
huart5.Init.OverSampling = UART_OVERSAMPLING_16;
|
|
huart5.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
|
|
huart5.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
|
|
if (HAL_UART_Init(&huart5) != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
/* USER CODE BEGIN UART5_Init 2 */
|
|
|
|
/* USER CODE END UART5_Init 2 */
|
|
|
|
}
|
|
|
|
/**
|
|
* @brief USART1 Initialization Function
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
static void MX_USART1_UART_Init(void)
|
|
{
|
|
|
|
/* USER CODE BEGIN USART1_Init 0 */
|
|
|
|
/* USER CODE END USART1_Init 0 */
|
|
|
|
/* USER CODE BEGIN USART1_Init 1 */
|
|
|
|
/* USER CODE END USART1_Init 1 */
|
|
huart1.Instance = USART1;
|
|
huart1.Init.BaudRate = 115200;
|
|
huart1.Init.WordLength = UART_WORDLENGTH_8B;
|
|
huart1.Init.StopBits = UART_STOPBITS_1;
|
|
huart1.Init.Parity = UART_PARITY_NONE;
|
|
huart1.Init.Mode = UART_MODE_TX_RX;
|
|
huart1.Init.HwFlowCtl = UART_HWCONTROL_NONE;
|
|
huart1.Init.OverSampling = UART_OVERSAMPLING_16;
|
|
huart1.Init.OneBitSampling = UART_ONE_BIT_SAMPLE_DISABLE;
|
|
huart1.AdvancedInit.AdvFeatureInit = UART_ADVFEATURE_NO_INIT;
|
|
if (HAL_UART_Init(&huart1) != HAL_OK)
|
|
{
|
|
Error_Handler();
|
|
}
|
|
/* USER CODE BEGIN USART1_Init 2 */
|
|
|
|
/* USER CODE END USART1_Init 2 */
|
|
|
|
}
|
|
|
|
/**
|
|
* @brief GPIO Initialization Function
|
|
* @param None
|
|
* @retval None
|
|
*/
|
|
static void MX_GPIO_Init(void)
|
|
{
|
|
|
|
/* GPIO Ports Clock Enable */
|
|
__HAL_RCC_GPIOE_CLK_ENABLE();
|
|
__HAL_RCC_GPIOG_CLK_ENABLE();
|
|
__HAL_RCC_GPIOC_CLK_ENABLE();
|
|
__HAL_RCC_GPIOA_CLK_ENABLE();
|
|
__HAL_RCC_GPIOD_CLK_ENABLE();
|
|
__HAL_RCC_GPIOH_CLK_ENABLE();
|
|
|
|
}
|
|
|
|
/* USER CODE BEGIN 4 */
|
|
|
|
/* USER CODE END 4 */
|
|
|
|
/**
|
|
* @brief This function is executed in case of error occurrence.
|
|
* @retval None
|
|
*/
|
|
void Error_Handler(void)
|
|
{
|
|
/* USER CODE BEGIN Error_Handler_Debug */
|
|
/* User can add his own implementation to report the HAL error return state */
|
|
|
|
/* USER CODE END Error_Handler_Debug */
|
|
}
|
|
|
|
#ifdef USE_FULL_ASSERT
|
|
/**
|
|
* @brief Reports the name of the source file and the source line number
|
|
* where the assert_param error has occurred.
|
|
* @param file: pointer to the source file name
|
|
* @param line: assert_param error line source number
|
|
* @retval None
|
|
*/
|
|
void assert_failed(uint8_t *file, uint32_t line)
|
|
{
|
|
/* USER CODE BEGIN 6 */
|
|
/* User can add his own implementation to report the file name and line number,
|
|
tex: printf("Wrong parameters value: file %s on line %d\r\n", file, line) */
|
|
/* USER CODE END 6 */
|
|
}
|
|
#endif /* USE_FULL_ASSERT */
|
|
|
|
/************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/
|