1222 lines
43 KiB
C
1222 lines
43 KiB
C
//*****************************************************************************
|
|
//
|
|
// udma.c - Driver for the micro-DMA controller.
|
|
//
|
|
// Copyright (c) 2007-2010 Texas Instruments Incorporated. All rights reserved.
|
|
// Software License Agreement
|
|
//
|
|
// Texas Instruments (TI) is supplying this software for use solely and
|
|
// exclusively on TI's microcontroller products. The software is owned by
|
|
// TI and/or its suppliers, and is protected under applicable copyright
|
|
// laws. You may not combine this software with "viral" open-source
|
|
// software in order to form a larger program.
|
|
//
|
|
// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
|
|
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
|
|
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
|
|
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
|
|
// DAMAGES, FOR ANY REASON WHATSOEVER.
|
|
//
|
|
// This is part of revision 6459 of the Stellaris Peripheral Driver Library.
|
|
//
|
|
//*****************************************************************************
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! \addtogroup udma_api
|
|
//! @{
|
|
//
|
|
//*****************************************************************************
|
|
|
|
#include "inc/hw_types.h"
|
|
#include "inc/hw_udma.h"
|
|
#include "driverlib/debug.h"
|
|
#include "driverlib/interrupt.h"
|
|
#include "driverlib/udma.h"
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Enables the uDMA controller for use.
|
|
//!
|
|
//! This function enables the uDMA controller. The uDMA controller must be
|
|
//! enabled before it can be configured and used.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAEnable(void)
|
|
{
|
|
//
|
|
// Set the master enable bit in the config register.
|
|
//
|
|
HWREG(UDMA_CFG) = UDMA_CFG_MASTEN;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Disables the uDMA controller for use.
|
|
//!
|
|
//! This function disables the uDMA controller. Once disabled, the uDMA
|
|
//! controller will not operate until re-enabled with uDMAEnable().
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMADisable(void)
|
|
{
|
|
//
|
|
// Clear the master enable bit in the config register.
|
|
//
|
|
HWREG(UDMA_CFG) = 0;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the uDMA error status.
|
|
//!
|
|
//! This function returns the uDMA error status. It should be called from
|
|
//! within the uDMA error interrupt handler to determine if a uDMA error
|
|
//! occurred.
|
|
//!
|
|
//! \return Returns non-zero if a uDMA error is pending.
|
|
//
|
|
//*****************************************************************************
|
|
unsigned long
|
|
uDMAErrorStatusGet(void)
|
|
{
|
|
//
|
|
// Return the uDMA error status.
|
|
//
|
|
return(HWREG(UDMA_ERRCLR));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Clears the uDMA error interrupt.
|
|
//!
|
|
//! This function clears a pending uDMA error interrupt. It should be called
|
|
//! from within the uDMA error interrupt handler to clear the interrupt.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAErrorStatusClear(void)
|
|
{
|
|
//
|
|
// Clear the uDMA error interrupt.
|
|
//
|
|
HWREG(UDMA_ERRCLR) = 1;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Enables a uDMA channel for operation.
|
|
//!
|
|
//! \param ulChannel is the channel number to enable.
|
|
//!
|
|
//! This function enables a specific uDMA channel for use. This function must
|
|
//! be used to enable a channel before it can be used to perform a uDMA
|
|
//! transfer.
|
|
//!
|
|
//! When a uDMA transfer is completed, the channel will be automatically
|
|
//! disabled by the uDMA controller. Therefore, this function should be called
|
|
//! prior to starting up any new transfer.
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelEnable(unsigned long ulChannel)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
|
|
//
|
|
// Set the bit for this channel in the enable set register.
|
|
//
|
|
HWREG(UDMA_ENASET) = 1 << ulChannel;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Disables a uDMA channel for operation.
|
|
//!
|
|
//! \param ulChannel is the channel number to disable.
|
|
//!
|
|
//! This function disables a specific uDMA channel. Once disabled, a channel
|
|
//! will not respond to uDMA transfer requests until re-enabled via
|
|
//! uDMAChannelEnable().
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelDisable(unsigned long ulChannel)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
|
|
//
|
|
// Set the bit for this channel in the enable clear register.
|
|
//
|
|
HWREG(UDMA_ENACLR) = 1 << ulChannel;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Checks if a uDMA channel is enabled for operation.
|
|
//!
|
|
//! \param ulChannel is the channel number to check.
|
|
//!
|
|
//! This function checks to see if a specific uDMA channel is enabled. This
|
|
//! can be used to check the status of a transfer, since the channel will
|
|
//! be automatically disabled at the end of a transfer.
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! \return Returns \b true if the channel is enabled, \b false if disabled.
|
|
//
|
|
//*****************************************************************************
|
|
tBoolean
|
|
uDMAChannelIsEnabled(unsigned long ulChannel)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
|
|
//
|
|
// AND the specified channel bit with the enable register, and return the
|
|
// result.
|
|
//
|
|
return((HWREG(UDMA_ENASET) & (1 << ulChannel)) ? true : false);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Sets the base address for the channel control table.
|
|
//!
|
|
//! \param pControlTable is a pointer to the 1024 byte aligned base address
|
|
//! of the uDMA channel control table.
|
|
//!
|
|
//! This function sets the base address of the channel control table. This
|
|
//! table resides in system memory and holds control information for each uDMA
|
|
//! channel. The table must be aligned on a 1024 byte boundary. The base
|
|
//! address must be set before any of the channel functions can be used.
|
|
//!
|
|
//! The size of the channel control table depends on the number of uDMA
|
|
//! channels, and which transfer modes are used. Refer to the introductory
|
|
//! text and the microcontroller datasheet for more information about the
|
|
//! channel control table.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAControlBaseSet(void *pControlTable)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(((unsigned long)pControlTable & ~0x3FF) ==
|
|
(unsigned long)pControlTable);
|
|
ASSERT((unsigned long)pControlTable >= 0x20000000);
|
|
|
|
//
|
|
// Program the base address into the register.
|
|
//
|
|
HWREG(UDMA_CTLBASE) = (unsigned long)pControlTable;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the base address for the channel control table.
|
|
//!
|
|
//! This function gets the base address of the channel control table. This
|
|
//! table resides in system memory and holds control information for each uDMA
|
|
//! channel.
|
|
//!
|
|
//! \return Returns a pointer to the base address of the channel control table.
|
|
//
|
|
//*****************************************************************************
|
|
void *
|
|
uDMAControlBaseGet(void)
|
|
{
|
|
//
|
|
// Read the current value of the control base register, and return it to
|
|
// the caller.
|
|
//
|
|
return((void *)HWREG(UDMA_CTLBASE));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Requests a uDMA channel to start a transfer.
|
|
//!
|
|
//! \param ulChannel is the channel number on which to request a uDMA transfer.
|
|
//!
|
|
//! This function allows software to request a uDMA channel to begin a
|
|
//! transfer. This could be used for performing a memory to memory transfer,
|
|
//! or if for some reason a transfer needs to be initiated by software instead
|
|
//! of the peripheral associated with that channel.
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! \note If the channel is \b UDMA_CHANNEL_SW and interrupts are used, then
|
|
//! the completion will be signaled on the uDMA dedicated interrupt. If a
|
|
//! peripheral channel is used, then the completion will be signaled on the
|
|
//! peripheral's interrupt.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelRequest(unsigned long ulChannel)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
|
|
//
|
|
// Set the bit for this channel in the software uDMA request register.
|
|
//
|
|
HWREG(UDMA_SWREQ) = 1 << ulChannel;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Enables attributes of a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the channel to configure.
|
|
//! \param ulAttr is a combination of attributes for the channel.
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! The \e ulAttr parameter is the logical OR of any of the following:
|
|
//!
|
|
//! - \b UDMA_ATTR_USEBURST is used to restrict transfers to use only a burst
|
|
//! mode.
|
|
//! - \b UDMA_ATTR_ALTSELECT is used to select the alternate control structure
|
|
//! for this channel.
|
|
//! - \b UDMA_ATTR_HIGH_PRIORITY is used to set this channel to high priority.
|
|
//! - \b UDMA_ATTR_REQMASK is used to mask the hardware request signal from the
|
|
//! peripheral for this channel.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelAttributeEnable(unsigned long ulChannel, unsigned long ulAttr)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
ASSERT((ulAttr & ~(UDMA_ATTR_USEBURST | UDMA_ATTR_ALTSELECT |
|
|
UDMA_ATTR_HIGH_PRIORITY | UDMA_ATTR_REQMASK)) == 0);
|
|
|
|
//
|
|
// Set the useburst bit for this channel if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_USEBURST)
|
|
{
|
|
HWREG(UDMA_USEBURSTSET) = 1 << ulChannel;
|
|
}
|
|
|
|
//
|
|
// Set the alternate control select bit for this channel,
|
|
// if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_ALTSELECT)
|
|
{
|
|
HWREG(UDMA_ALTSET) = 1 << ulChannel;
|
|
}
|
|
|
|
//
|
|
// Set the high priority bit for this channel, if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_HIGH_PRIORITY)
|
|
{
|
|
HWREG(UDMA_PRIOSET) = 1 << ulChannel;
|
|
}
|
|
|
|
//
|
|
// Set the request mask bit for this channel, if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_REQMASK)
|
|
{
|
|
HWREG(UDMA_REQMASKSET) = 1 << ulChannel;
|
|
}
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Disables attributes of a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the channel to configure.
|
|
//! \param ulAttr is a combination of attributes for the channel.
|
|
//!
|
|
//! This function is used to disable attributes of a uDMA channel.
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! The \e ulAttr parameter is the logical OR of any of the following:
|
|
//!
|
|
//! - \b UDMA_ATTR_USEBURST is used to restrict transfers to use only a burst
|
|
//! mode.
|
|
//! - \b UDMA_ATTR_ALTSELECT is used to select the alternate control structure
|
|
//! for this channel.
|
|
//! - \b UDMA_ATTR_HIGH_PRIORITY is used to set this channel to high priority.
|
|
//! - \b UDMA_ATTR_REQMASK is used to mask the hardware request signal from the
|
|
//! peripheral for this channel.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelAttributeDisable(unsigned long ulChannel, unsigned long ulAttr)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
ASSERT((ulAttr & ~(UDMA_ATTR_USEBURST | UDMA_ATTR_ALTSELECT |
|
|
UDMA_ATTR_HIGH_PRIORITY | UDMA_ATTR_REQMASK)) == 0);
|
|
|
|
//
|
|
// Clear the useburst bit for this channel if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_USEBURST)
|
|
{
|
|
HWREG(UDMA_USEBURSTCLR) = 1 << ulChannel;
|
|
}
|
|
|
|
//
|
|
// Clear the alternate control select bit for this channel, if set in
|
|
// ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_ALTSELECT)
|
|
{
|
|
HWREG(UDMA_ALTCLR) = 1 << ulChannel;
|
|
}
|
|
|
|
//
|
|
// Clear the high priority bit for this channel, if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_HIGH_PRIORITY)
|
|
{
|
|
HWREG(UDMA_PRIOCLR) = 1 << ulChannel;
|
|
}
|
|
|
|
//
|
|
// Clear the request mask bit for this channel, if set in ulConfig.
|
|
//
|
|
if(ulAttr & UDMA_ATTR_REQMASK)
|
|
{
|
|
HWREG(UDMA_REQMASKCLR) = 1 << ulChannel;
|
|
}
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the enabled attributes of a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the channel to configure.
|
|
//!
|
|
//! This function returns a combination of flags representing the attributes of
|
|
//! the uDMA channel.
|
|
//!
|
|
//! The \e ulChannel parameter must be one of the following:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_UART0RX for UART 0 receive channel
|
|
//! - \b UDMA_CHANNEL_UART0TX for UART 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_UART1RX for UART 1 receive channel
|
|
//! - \b UDMA_CHANNEL_UART1TX for UART 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI0RX for SSI 0 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI0TX for SSI 0 transmit channel
|
|
//! - \b UDMA_CHANNEL_SSI1RX for SSI 1 receive channel
|
|
//! - \b UDMA_CHANNEL_SSI1TX for SSI 1 transmit channel
|
|
//! - \b UDMA_CHANNEL_SW for the software dedicated uDMA channel
|
|
//!
|
|
//! And for microcontrollers that have a USB peripheral:
|
|
//!
|
|
//! - \b UDMA_CHANNEL_USBEP1RX for USB endpoint 1 receive
|
|
//! - \b UDMA_CHANNEL_USBEP1TX for USB endpoint 1 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP2RX for USB endpoint 2 receive
|
|
//! - \b UDMA_CHANNEL_USBEP2TX for USB endpoint 2 transmit
|
|
//! - \b UDMA_CHANNEL_USBEP3RX for USB endpoint 3 receive
|
|
//! - \b UDMA_CHANNEL_USBEP3TX for USB endpoint 3 transmit
|
|
//!
|
|
//! \return Returns the logical OR of the attributes of the uDMA channel, which
|
|
//! can be any of the following:
|
|
//! - \b UDMA_ATTR_USEBURST is used to restrict transfers to use only a burst
|
|
//! mode.
|
|
//! - \b UDMA_ATTR_ALTSELECT is used to select the alternate control structure
|
|
//! for this channel.
|
|
//! - \b UDMA_ATTR_HIGH_PRIORITY is used to set this channel to high priority.
|
|
//! - \b UDMA_ATTR_REQMASK is used to mask the hardware request signal from the
|
|
//! peripheral for this channel.
|
|
//
|
|
//*****************************************************************************
|
|
unsigned long
|
|
uDMAChannelAttributeGet(unsigned long ulChannel)
|
|
{
|
|
unsigned long ulAttr = 0;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 32);
|
|
|
|
//
|
|
// Check to see if useburst bit is set for this channel.
|
|
//
|
|
if(HWREG(UDMA_USEBURSTSET) & (1 << ulChannel))
|
|
{
|
|
ulAttr |= UDMA_ATTR_USEBURST;
|
|
}
|
|
|
|
//
|
|
// Check to see if the alternate control bit is set for this channel.
|
|
//
|
|
if(HWREG(UDMA_ALTSET) & (1 << ulChannel))
|
|
{
|
|
ulAttr |= UDMA_ATTR_ALTSELECT;
|
|
}
|
|
|
|
//
|
|
// Check to see if the high priority bit is set for this channel.
|
|
//
|
|
if(HWREG(UDMA_PRIOSET) & (1 << ulChannel))
|
|
{
|
|
ulAttr |= UDMA_ATTR_HIGH_PRIORITY;
|
|
}
|
|
|
|
//
|
|
// Check to see if the request mask bit is set for this channel.
|
|
//
|
|
if(HWREG(UDMA_REQMASKSET) & (1 << ulChannel))
|
|
{
|
|
ulAttr |= UDMA_ATTR_REQMASK;
|
|
}
|
|
|
|
//
|
|
// Return the configuration flags.
|
|
//
|
|
return(ulAttr);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Sets the control parameters for a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the logical OR of the uDMA channel number with
|
|
//! \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT.
|
|
//! \param ulControl is logical OR of several control values to set the control
|
|
//! parameters for the channel.
|
|
//!
|
|
//! This function is used to set control parameters for a uDMA transfer. These
|
|
//! are typically parameters that are not changed often.
|
|
//!
|
|
//! The \e ulChannel parameter is one of the choices documented in the
|
|
//! uDMAChannelEnable() function. It should be the logical OR of the channel
|
|
//! with one of \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT to choose whether
|
|
//! the primary or alternate data structure is used.
|
|
//!
|
|
//! The \e ulControl parameter is the logical OR of five values: the data size,
|
|
//! the source address increment, the destination address increment, the
|
|
//! arbitration size, and the use burst flag. The choices available for each
|
|
//! of these values is described below.
|
|
//!
|
|
//! Choose the data size from one of \b UDMA_SIZE_8, \b UDMA_SIZE_16, or
|
|
//! \b UDMA_SIZE_32 to select a data size of 8, 16, or 32 bits.
|
|
//!
|
|
//! Choose the source address increment from one of \b UDMA_SRC_INC_8,
|
|
//! \b UDMA_SRC_INC_16, \b UDMA_SRC_INC_32, or \b UDMA_SRC_INC_NONE to select
|
|
//! an address increment of 8-bit bytes, 16-bit halfwords, 32-bit words, or
|
|
//! to select non-incrementing.
|
|
//!
|
|
//! Choose the destination address increment from one of \b UDMA_DST_INC_8,
|
|
//! \b UDMA_DST_INC_16, \b UDMA_DST_INC_32, or \b UDMA_DST_INC_NONE to select
|
|
//! an address increment of 8-bit bytes, 16-bit halfwords, 32-bit words, or
|
|
//! to select non-incrementing.
|
|
//!
|
|
//! The arbitration size determines how many items are transferred before
|
|
//! the uDMA controller re-arbitrates for the bus. Choose the arbitration size
|
|
//! from one of \b UDMA_ARB_1, \b UDMA_ARB_2, \b UDMA_ARB_4, \b UDMA_ARB_8,
|
|
//! through \b UDMA_ARB_1024 to select the arbitration size from 1 to 1024
|
|
//! items, in powers of 2.
|
|
//!
|
|
//! The value \b UDMA_NEXT_USEBURST is used to force the channel to only
|
|
//! respond to burst requests at the tail end of a scatter-gather transfer.
|
|
//!
|
|
//! \note The address increment cannot be smaller than the data size.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelControlSet(unsigned long ulChannel, unsigned long ulControl)
|
|
{
|
|
tDMAControlTable *pCtl;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 64);
|
|
ASSERT(HWREG(UDMA_CTLBASE) != 0);
|
|
|
|
//
|
|
// Get the base address of the control table.
|
|
//
|
|
pCtl = (tDMAControlTable *)HWREG(UDMA_CTLBASE);
|
|
|
|
//
|
|
// Get the current control word value and mask off the fields to be
|
|
// changed, then OR in the new settings.
|
|
//
|
|
pCtl[ulChannel].ulControl = ((pCtl[ulChannel].ulControl &
|
|
~(UDMA_CHCTL_DSTINC_M |
|
|
UDMA_CHCTL_DSTSIZE_M |
|
|
UDMA_CHCTL_SRCINC_M |
|
|
UDMA_CHCTL_SRCSIZE_M |
|
|
UDMA_CHCTL_ARBSIZE_M |
|
|
UDMA_CHCTL_NXTUSEBURST)) |
|
|
ulControl);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Sets the transfer parameters for a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the logical or of the uDMA channel number with either
|
|
//! \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT.
|
|
//! \param ulMode is the type of uDMA transfer.
|
|
//! \param pvSrcAddr is the source address for the transfer.
|
|
//! \param pvDstAddr is the destination address for the transfer.
|
|
//! \param ulTransferSize is the number of data items to transfer.
|
|
//!
|
|
//! This function is used to set the parameters for a uDMA transfer. These are
|
|
//! typically parameters that are changed often. The function
|
|
//! uDMAChannelControlSet() MUST be called at least once for this channel prior
|
|
//! to calling this function.
|
|
//!
|
|
//! The \e ulChannel parameter is one of the choices documented in the
|
|
//! uDMAChannelEnable() function. It should be the logical OR of the channel
|
|
//! with either \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT to choose whether the
|
|
//! primary or alternate data structure is used.
|
|
//!
|
|
//! The \e ulMode parameter should be one of the following values:
|
|
//!
|
|
//! - \b UDMA_MODE_STOP stops the uDMA transfer. The controller sets the mode
|
|
//! to this value at the end of a transfer.
|
|
//! - \b UDMA_MODE_BASIC to perform a basic transfer based on request.
|
|
//! - \b UDMA_MODE_AUTO to perform a transfer that will always complete once
|
|
//! started even if request is removed.
|
|
//! - \b UDMA_MODE_PINGPONG to set up a transfer that switches between the
|
|
//! primary and alternate control structures for the channel. This allows
|
|
//! use of ping-pong buffering for uDMA transfers.
|
|
//! - \b UDMA_MODE_MEM_SCATTER_GATHER to set up a memory scatter-gather
|
|
//! transfer.
|
|
//! - \b UDMA_MODE_PER_SCATTER_GATHER to set up a peripheral scatter-gather
|
|
//! transfer.
|
|
//!
|
|
//! The \e pvSrcAddr and \e pvDstAddr parameters are pointers to the first
|
|
//! location of the data to be transferred. These addresses should be aligned
|
|
//! according to the item size. The compiler will take care of this if the
|
|
//! pointers are pointing to storage of the appropriate data type.
|
|
//!
|
|
//! The \e ulTransferSize parameter is the number of data items, not the number
|
|
//! of bytes.
|
|
//!
|
|
//! The two scatter/gather modes, memory and peripheral, are actually different
|
|
//! depending on whether the primary or alternate control structure is
|
|
//! selected. This function will look for the \b UDMA_PRI_SELECT and
|
|
//! \b UDMA_ALT_SELECT flag along with the channel number and will set the
|
|
//! scatter/gather mode as appropriate for the primary or alternate control
|
|
//! structure.
|
|
//!
|
|
//! The channel must also be enabled using uDMAChannelEnable() after calling
|
|
//! this function. The transfer will not begin until the channel has been set
|
|
//! up and enabled. Note that the channel is automatically disabled after the
|
|
//! transfer is completed, meaning that uDMAChannelEnable() must be called
|
|
//! again after setting up the next transfer.
|
|
//!
|
|
//! \note Great care must be taken to not modify a channel control structure
|
|
//! that is in use or else the results will be unpredictable, including the
|
|
//! possibility of undesired data transfers to or from memory or peripherals.
|
|
//! For BASIC and AUTO modes, it is safe to make changes when the channel is
|
|
//! disabled, or the uDMAChannelModeGet() returns \b UDMA_MODE_STOP. For
|
|
//! PINGPONG or one of the SCATTER_GATHER modes, it is safe to modify the
|
|
//! primary or alternate control structure only when the other is being used.
|
|
//! The uDMAChannelModeGet() function will return \b UDMA_MODE_STOP when a
|
|
//! channel control structure is inactive and safe to modify.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelTransferSet(unsigned long ulChannel, unsigned long ulMode,
|
|
void *pvSrcAddr, void *pvDstAddr,
|
|
unsigned long ulTransferSize)
|
|
{
|
|
tDMAControlTable *pControlTable;
|
|
unsigned long ulControl;
|
|
unsigned long ulSize;
|
|
unsigned long ulInc;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 64);
|
|
ASSERT(HWREG(UDMA_CTLBASE) != 0);
|
|
ASSERT(ulMode <= UDMA_MODE_PER_SCATTER_GATHER);
|
|
ASSERT((unsigned long)pvSrcAddr >= 0x20000000);
|
|
ASSERT((unsigned long)pvDstAddr >= 0x20000000);
|
|
ASSERT((ulTransferSize != 0) && (ulTransferSize <= 1024));
|
|
|
|
//
|
|
// Get the base address of the control table.
|
|
//
|
|
pControlTable = (tDMAControlTable *)HWREG(UDMA_CTLBASE);
|
|
|
|
//
|
|
// Get the current control word value and mask off the mode and size
|
|
// fields.
|
|
//
|
|
ulControl = (pControlTable[ulChannel].ulControl &
|
|
~(UDMA_CHCTL_XFERSIZE_M | UDMA_CHCTL_XFERMODE_M));
|
|
|
|
//
|
|
// Adjust the mode if the alt control structure is selected.
|
|
//
|
|
if(ulChannel & UDMA_ALT_SELECT)
|
|
{
|
|
if((ulMode == UDMA_MODE_MEM_SCATTER_GATHER) ||
|
|
(ulMode == UDMA_MODE_PER_SCATTER_GATHER))
|
|
{
|
|
ulMode |= UDMA_MODE_ALT_SELECT;
|
|
}
|
|
}
|
|
|
|
//
|
|
// Set the transfer size and mode in the control word (but dont write the
|
|
// control word yet as it could kick off a transfer).
|
|
//
|
|
ulControl |= ulMode | ((ulTransferSize - 1) << 4);
|
|
|
|
//
|
|
// Get the data item size from the control word (set previously).
|
|
//
|
|
ulSize = (ulControl & UDMA_CHCTL_DSTSIZE_M) >> 28;
|
|
|
|
//
|
|
// Convert the transfer size to be in units of bytes. Shift (multiply) to
|
|
// get the value in bytes, based on the data item size.
|
|
//
|
|
ulTransferSize = ulTransferSize << ulSize;
|
|
|
|
//
|
|
// Get the address increment value for the source, from the control word.
|
|
//
|
|
ulInc = (ulControl & UDMA_CHCTL_SRCINC_M);
|
|
|
|
//
|
|
// Compute the ending source address of the transfer. If the source
|
|
// increment is set to none, then the ending address is the same as the
|
|
// beginning.
|
|
//
|
|
if(ulInc != UDMA_SRC_INC_NONE)
|
|
{
|
|
pvSrcAddr = (void *)((unsigned long)pvSrcAddr + ulTransferSize - 1);
|
|
}
|
|
|
|
//
|
|
// Load the source ending address into the control block.
|
|
//
|
|
pControlTable[ulChannel].pvSrcEndAddr = pvSrcAddr;
|
|
|
|
//
|
|
// Get the address increment value for the destination, from the control
|
|
// word.
|
|
//
|
|
ulInc = (ulControl & UDMA_CHCTL_DSTINC_M);
|
|
|
|
//
|
|
// Compute the ending destination address of the transfer. If the
|
|
// destination increment is set to none, then the ending address is the
|
|
// same as the beginning.
|
|
//
|
|
if(ulInc != UDMA_DST_INC_NONE)
|
|
{
|
|
pvDstAddr = (void *)((unsigned long)pvDstAddr + ulTransferSize - 1);
|
|
}
|
|
|
|
//
|
|
// Load the destination ending address into the control block.
|
|
//
|
|
pControlTable[ulChannel].pvDstEndAddr = pvDstAddr;
|
|
|
|
//
|
|
// Write the new control word value.
|
|
//
|
|
pControlTable[ulChannel].ulControl = ulControl;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the current transfer size for a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the logical or of the uDMA channel number with either
|
|
//! \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT.
|
|
//!
|
|
//! This function is used to get the uDMA transfer size for a channel. The
|
|
//! transfer size is the number of items to transfer, where the size of an item
|
|
//! might be 8, 16, or 32 bits. If a partial transfer has already occurred,
|
|
//! then the number of remaining items will be returned. If the transfer is
|
|
//! complete, then 0 will be returned.
|
|
//!
|
|
//! The \e ulChannel parameter is one of the choices documented in the
|
|
//! uDMAChannelEnable() function. It should be the logical OR of the channel
|
|
//! with either \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT to choose whether
|
|
//! the primary or alternate data structure is used.
|
|
//!
|
|
//! \return Returns the number of items remaining to transfer.
|
|
//
|
|
//*****************************************************************************
|
|
unsigned long
|
|
uDMAChannelSizeGet(unsigned long ulChannel)
|
|
{
|
|
tDMAControlTable *pControlTable;
|
|
unsigned long ulControl;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 64);
|
|
ASSERT(HWREG(UDMA_CTLBASE) != 0);
|
|
|
|
//
|
|
// Get the base address of the control table.
|
|
//
|
|
pControlTable = (tDMAControlTable *)HWREG(UDMA_CTLBASE);
|
|
|
|
//
|
|
// Get the current control word value and mask off all but the size field
|
|
// and the mode field.
|
|
//
|
|
ulControl = pControlTable[ulChannel].ulControl &
|
|
(UDMA_CHCTL_XFERSIZE_M | UDMA_CHCTL_XFERMODE_M);
|
|
|
|
//
|
|
// If the size field and mode field are 0 then the transfer is finished
|
|
// and there are no more items to transfer
|
|
//
|
|
if(ulControl == 0)
|
|
{
|
|
return(0);
|
|
}
|
|
|
|
//
|
|
// Otherwise, if either the size field or more field is non-zero, then
|
|
// not all the items have been transferred.
|
|
//
|
|
else
|
|
{
|
|
//
|
|
// Shift the size field and add one, then return to user.
|
|
//
|
|
return((ulControl >> 4) + 1);
|
|
}
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the transfer mode for a uDMA channel.
|
|
//!
|
|
//! \param ulChannel is the logical or of the uDMA channel number with either
|
|
//! \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT.
|
|
//!
|
|
//! This function is used to get the transfer mode for the uDMA channel. It
|
|
//! can be used to query the status of a transfer on a channel. When the
|
|
//! transfer is complete the mode will be \b UDMA_MODE_STOP.
|
|
//!
|
|
//! The \e ulChannel parameter is one of the choices documented in the
|
|
//! uDMAChannelEnable() function. It should be the logical OR of the channel
|
|
//! with either \b UDMA_PRI_SELECT or \b UDMA_ALT_SELECT to choose whether the
|
|
//! primary or alternate data structure is used.
|
|
//!
|
|
//! \return Returns the transfer mode of the specified channel and control
|
|
//! structure, which will be one of the following values: \b UDMA_MODE_STOP,
|
|
//! \b UDMA_MODE_BASIC, \b UDMA_MODE_AUTO, \b UDMA_MODE_PINGPONG,
|
|
//! \b UDMA_MODE_MEM_SCATTER_GATHER, or \b UDMA_MODE_PER_SCATTER_GATHER.
|
|
//
|
|
//*****************************************************************************
|
|
unsigned long
|
|
uDMAChannelModeGet(unsigned long ulChannel)
|
|
{
|
|
tDMAControlTable *pControlTable;
|
|
unsigned long ulControl;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(ulChannel < 64);
|
|
ASSERT(HWREG(UDMA_CTLBASE) != 0);
|
|
|
|
//
|
|
// Get the base address of the control table.
|
|
//
|
|
pControlTable = (tDMAControlTable *)HWREG(UDMA_CTLBASE);
|
|
|
|
//
|
|
// Get the current control word value and mask off all but the mode field.
|
|
//
|
|
ulControl = pControlTable[ulChannel].ulControl & UDMA_CHCTL_XFERMODE_M;
|
|
|
|
//
|
|
// Check if scatter/gather mode, and if so, mask off the alt bit.
|
|
//
|
|
if(((ulControl & ~UDMA_MODE_ALT_SELECT) == UDMA_MODE_MEM_SCATTER_GATHER) ||
|
|
((ulControl & ~UDMA_MODE_ALT_SELECT) == UDMA_MODE_PER_SCATTER_GATHER))
|
|
{
|
|
ulControl &= ~UDMA_MODE_ALT_SELECT;
|
|
}
|
|
|
|
//
|
|
// Return the mode to the caller.
|
|
//
|
|
return(ulControl);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Selects the secondary peripheral for a set of uDMA channels.
|
|
//!
|
|
//! \param ulSecPeriphs is the logical or of the uDMA channels for which to
|
|
//! use the secondary peripheral, instead of the default peripheral.
|
|
//!
|
|
//! This function is used to select the secondary peripheral assignment for
|
|
//! a set of uDMA channels. By selecting the secondary peripheral assignment
|
|
//! for a channel, the default peripheral assignment is no longer available
|
|
//! for that channel.
|
|
//!
|
|
//! The parameter \e ulSecPeriphs can be the logical OR of any of the
|
|
//! following macros. If one of the macros below is in the list passed
|
|
//! to this function, then the secondary peripheral (marked as \b _SEC_)
|
|
//! will be selected.
|
|
//!
|
|
//! - \b UDMA_DEF_USBEP1RX_SEC_UART2RX
|
|
//! - \b UDMA_DEF_USBEP1TX_SEC_UART2TX
|
|
//! - \b UDMA_DEF_USBEP2RX_SEC_TMR3A
|
|
//! - \b UDMA_DEF_USBEP2TX_SEC_TMR3B
|
|
//! - \b UDMA_DEF_USBEP3RX_SEC_TMR2A
|
|
//! - \b UDMA_DEF_USBEP3TX_SEC_TMR2B
|
|
//! - \b UDMA_DEF_ETH0RX_SEC_TMR2A
|
|
//! - \b UDMA_DEF_ETH0TX_SEC_TMR2B
|
|
//! - \b UDMA_DEF_UART0RX_SEC_UART1RX
|
|
//! - \b UDMA_DEF_UART0TX_SEC_UART1TX
|
|
//! - \b UDMA_DEF_SSI0RX_SEC_SSI1RX
|
|
//! - \b UDMA_DEF_SSI0TX_SEC_SSI1TX
|
|
//! - \b UDMA_DEF_RESERVED_SEC_UART2RX
|
|
//! - \b UDMA_DEF_RESERVED_SEC_UART2TX
|
|
//! - \b UDMA_DEF_ADC00_SEC_TMR2A
|
|
//! - \b UDMA_DEF_ADC01_SEC_TMR2B
|
|
//! - \b UDMA_DEF_ADC02_SEC_RESERVED
|
|
//! - \b UDMA_DEF_ADC03_SEC_RESERVED
|
|
//! - \b UDMA_DEF_TMR0A_SEC_TMR1A
|
|
//! - \b UDMA_DEF_TMR0B_SEC_TMR1B
|
|
//! - \b UDMA_DEF_TMR1A_SEC_EPI0RX
|
|
//! - \b UDMA_DEF_TMR1B_SEC_EPI0TX
|
|
//! - \b UDMA_DEF_UART1RX_SEC_RESERVED
|
|
//! - \b UDMA_DEF_UART1TX_SEC_RESERVED
|
|
//! - \b UDMA_DEF_SSI1RX_SEC_ADC10
|
|
//! - \b UDMA_DEF_SSI1TX_SEC_ADC11
|
|
//! - \b UDMA_DEF_RESERVED_SEC_ADC12
|
|
//! - \b UDMA_DEF_RESERVED_SEC_ADC13
|
|
//! - \b UDMA_DEF_I2S0RX_SEC_RESERVED
|
|
//! - \b UDMA_DEF_I2S0TX_SEC_RESERVED
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelSelectSecondary(unsigned long ulSecPeriphs)
|
|
{
|
|
//
|
|
// Select the secondary peripheral for the specified channels.
|
|
//
|
|
HWREG(UDMA_CHALT) |= ulSecPeriphs;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Selects the default peripheral for a set of uDMA channels.
|
|
//!
|
|
//! \param ulDefPeriphs is the logical or of the uDMA channels for which to
|
|
//! use the default peripheral, instead of the secondary peripheral.
|
|
//!
|
|
//! This function is used to select the default peripheral assignment for
|
|
//! a set of uDMA channels.
|
|
//!
|
|
//! The parameter \e ulDefPeriphs can be the logical OR of any of the
|
|
//! following macros. If one of the macros below is in the list passed
|
|
//! to this function, then the default peripheral (marked as \b _DEF_)
|
|
//! will be selected.
|
|
//!
|
|
//! - \b UDMA_DEF_USBEP1RX_SEC_UART2RX
|
|
//! - \b UDMA_DEF_USBEP1TX_SEC_UART2TX
|
|
//! - \b UDMA_DEF_USBEP2RX_SEC_TMR3A
|
|
//! - \b UDMA_DEF_USBEP2TX_SEC_TMR3B
|
|
//! - \b UDMA_DEF_USBEP3RX_SEC_TMR2A
|
|
//! - \b UDMA_DEF_USBEP3TX_SEC_TMR2B
|
|
//! - \b UDMA_DEF_ETH0RX_SEC_TMR2A
|
|
//! - \b UDMA_DEF_ETH0TX_SEC_TMR2B
|
|
//! - \b UDMA_DEF_UART0RX_SEC_UART1RX
|
|
//! - \b UDMA_DEF_UART0TX_SEC_UART1TX
|
|
//! - \b UDMA_DEF_SSI0RX_SEC_SSI1RX
|
|
//! - \b UDMA_DEF_SSI0TX_SEC_SSI1TX
|
|
//! - \b UDMA_DEF_RESERVED_SEC_UART2RX
|
|
//! - \b UDMA_DEF_RESERVED_SEC_UART2TX
|
|
//! - \b UDMA_DEF_ADC00_SEC_TMR2A
|
|
//! - \b UDMA_DEF_ADC01_SEC_TMR2B
|
|
//! - \b UDMA_DEF_ADC02_SEC_RESERVED
|
|
//! - \b UDMA_DEF_ADC03_SEC_RESERVED
|
|
//! - \b UDMA_DEF_TMR0A_SEC_TMR1A
|
|
//! - \b UDMA_DEF_TMR0B_SEC_TMR1B
|
|
//! - \b UDMA_DEF_TMR1A_SEC_EPI0RX
|
|
//! - \b UDMA_DEF_TMR1B_SEC_EPI0TX
|
|
//! - \b UDMA_DEF_UART1RX_SEC_RESERVED
|
|
//! - \b UDMA_DEF_UART1TX_SEC_RESERVED
|
|
//! - \b UDMA_DEF_SSI1RX_SEC_ADC10
|
|
//! - \b UDMA_DEF_SSI1TX_SEC_ADC11
|
|
//! - \b UDMA_DEF_RESERVED_SEC_ADC12
|
|
//! - \b UDMA_DEF_RESERVED_SEC_ADC13
|
|
//! - \b UDMA_DEF_I2S0RX_SEC_RESERVED
|
|
//! - \b UDMA_DEF_I2S0TX_SEC_RESERVED
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAChannelSelectDefault(unsigned long ulDefPeriphs)
|
|
{
|
|
//
|
|
// Select the default peripheral for the specified channels.
|
|
//
|
|
HWREG(UDMA_CHALT) &= ~ulDefPeriphs;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Registers an interrupt handler for the uDMA controller.
|
|
//!
|
|
//! \param ulIntChannel identifies which uDMA interrupt is to be registered.
|
|
//! \param pfnHandler is a pointer to the function to be called when the
|
|
//! interrupt is activated.
|
|
//!
|
|
//! This sets and enables the handler to be called when the uDMA controller
|
|
//! generates an interrupt. The \e ulIntChannel parameter should be one of the
|
|
//! following:
|
|
//!
|
|
//! - \b UDMA_INT_SW to register an interrupt handler to process interrupts
|
|
//! from the uDMA software channel (UDMA_CHANNEL_SW)
|
|
//! - \b UDMA_INT_ERR to register an interrupt handler to process uDMA error
|
|
//! interrupts
|
|
//!
|
|
//! \sa IntRegister() for important information about registering interrupt
|
|
//! handlers.
|
|
//!
|
|
//! \note The interrupt handler for uDMA is for transfer completion when the
|
|
//! channel UDMA_CHANNEL_SW is used, and for error interrupts. The
|
|
//! interrupts for each peripheral channel are handled through the individual
|
|
//! peripheral interrupt handlers.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAIntRegister(unsigned long ulIntChannel, void (*pfnHandler)(void))
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(pfnHandler);
|
|
ASSERT((ulIntChannel == UDMA_INT_SW) || (ulIntChannel == UDMA_INT_ERR));
|
|
|
|
//
|
|
// Register the interrupt handler.
|
|
//
|
|
IntRegister(ulIntChannel, pfnHandler);
|
|
|
|
//
|
|
// Enable the memory management fault.
|
|
//
|
|
IntEnable(ulIntChannel);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Unregisters an interrupt handler for the uDMA controller.
|
|
//!
|
|
//! \param ulIntChannel identifies which uDMA interrupt to unregister.
|
|
//!
|
|
//! This function will disable and clear the handler to be called for the
|
|
//! specified uDMA interrupt. The \e ulIntChannel parameter should be one of
|
|
//! \b UDMA_INT_SW or \b UDMA_INT_ERR as documented for the function
|
|
//! uDMAIntRegister().
|
|
//!
|
|
//! \sa IntRegister() for important information about registering interrupt
|
|
//! handlers.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
uDMAIntUnregister(unsigned long ulIntChannel)
|
|
{
|
|
//
|
|
// Disable the interrupt.
|
|
//
|
|
IntDisable(ulIntChannel);
|
|
|
|
//
|
|
// Unregister the interrupt handler.
|
|
//
|
|
IntUnregister(ulIntChannel);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Close the Doxygen group.
|
|
//! @}
|
|
//
|
|
//*****************************************************************************
|