2068 lines
69 KiB
C
2068 lines
69 KiB
C
//*****************************************************************************
|
|
//
|
|
// gpio.c - API for GPIO ports
|
|
//
|
|
// Copyright (c) 2005-2011 Texas Instruments Incorporated. All rights reserved.
|
|
// Software License Agreement
|
|
//
|
|
// Texas Instruments (TI) is supplying this software for use solely and
|
|
// exclusively on TI's microcontroller products. The software is owned by
|
|
// TI and/or its suppliers, and is protected under applicable copyright
|
|
// laws. You may not combine this software with "viral" open-source
|
|
// software in order to form a larger program.
|
|
//
|
|
// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
|
|
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
|
|
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
|
|
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
|
|
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
|
|
// DAMAGES, FOR ANY REASON WHATSOEVER.
|
|
//
|
|
// This is part of revision 8264 of the Stellaris Peripheral Driver Library.
|
|
//
|
|
//*****************************************************************************
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! \addtogroup gpio_api
|
|
//! @{
|
|
//
|
|
//*****************************************************************************
|
|
|
|
#include "inc/hw_gpio.h"
|
|
#include "inc/hw_ints.h"
|
|
#include "inc/hw_memmap.h"
|
|
#include "inc/hw_sysctl.h"
|
|
#include "inc/hw_types.h"
|
|
#include "driverlib/debug.h"
|
|
#include "driverlib/gpio.h"
|
|
#include "driverlib/interrupt.h"
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// The base addresses of all the GPIO modules. Both the APB and AHB apertures
|
|
// are provided.
|
|
//
|
|
//*****************************************************************************
|
|
static const unsigned long g_pulGPIOBaseAddrs[] =
|
|
{
|
|
GPIO_PORTA_BASE, GPIO_PORTA_AHB_BASE,
|
|
GPIO_PORTB_BASE, GPIO_PORTB_AHB_BASE,
|
|
GPIO_PORTC_BASE, GPIO_PORTC_AHB_BASE,
|
|
GPIO_PORTD_BASE, GPIO_PORTD_AHB_BASE,
|
|
GPIO_PORTE_BASE, GPIO_PORTE_AHB_BASE,
|
|
GPIO_PORTF_BASE, GPIO_PORTF_AHB_BASE,
|
|
GPIO_PORTG_BASE, GPIO_PORTG_AHB_BASE,
|
|
GPIO_PORTH_BASE, GPIO_PORTH_AHB_BASE,
|
|
GPIO_PORTJ_BASE, GPIO_PORTJ_AHB_BASE,
|
|
GPIO_PORTK_BASE, GPIO_PORTK_BASE,
|
|
GPIO_PORTL_BASE, GPIO_PORTL_BASE,
|
|
GPIO_PORTM_BASE, GPIO_PORTM_BASE,
|
|
GPIO_PORTN_BASE, GPIO_PORTN_BASE,
|
|
GPIO_PORTP_BASE, GPIO_PORTP_BASE,
|
|
GPIO_PORTQ_BASE, GPIO_PORTQ_BASE,
|
|
};
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! \internal
|
|
//! Checks a GPIO base address.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//!
|
|
//! This function determines if a GPIO port base address is valid.
|
|
//!
|
|
//! \return Returns \b true if the base address is valid and \b false
|
|
//! otherwise.
|
|
//
|
|
//*****************************************************************************
|
|
#ifdef DEBUG
|
|
static tBoolean
|
|
GPIOBaseValid(unsigned long ulPort)
|
|
{
|
|
return((ulPort == GPIO_PORTA_BASE) || (ulPort == GPIO_PORTA_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTB_BASE) || (ulPort == GPIO_PORTB_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTC_BASE) || (ulPort == GPIO_PORTC_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTD_BASE) || (ulPort == GPIO_PORTD_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTE_BASE) || (ulPort == GPIO_PORTE_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTF_BASE) || (ulPort == GPIO_PORTF_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTG_BASE) || (ulPort == GPIO_PORTG_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTH_BASE) || (ulPort == GPIO_PORTH_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTJ_BASE) || (ulPort == GPIO_PORTJ_AHB_BASE) ||
|
|
(ulPort == GPIO_PORTK_BASE) || (ulPort == GPIO_PORTL_BASE) ||
|
|
(ulPort == GPIO_PORTM_BASE) || (ulPort == GPIO_PORTN_BASE) ||
|
|
(ulPort == GPIO_PORTP_BASE) || (ulPort == GPIO_PORTQ_BASE));
|
|
}
|
|
#endif
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! \internal
|
|
//! Gets the GPIO interrupt number.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//!
|
|
//! Given a GPIO base address, this function returns the corresponding
|
|
//! interrupt number.
|
|
//!
|
|
//! \return Returns a GPIO interrupt number, or -1 if \e ulPort is invalid.
|
|
//
|
|
//*****************************************************************************
|
|
static long
|
|
GPIOGetIntNumber(unsigned long ulPort)
|
|
{
|
|
long lInt;
|
|
|
|
//
|
|
// Determine the GPIO interrupt number for the given module.
|
|
//
|
|
switch(ulPort)
|
|
{
|
|
case GPIO_PORTA_BASE:
|
|
case GPIO_PORTA_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOA;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTB_BASE:
|
|
case GPIO_PORTB_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOB;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTC_BASE:
|
|
case GPIO_PORTC_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOC;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTD_BASE:
|
|
case GPIO_PORTD_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOD;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTE_BASE:
|
|
case GPIO_PORTE_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOE;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTF_BASE:
|
|
case GPIO_PORTF_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOF;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTG_BASE:
|
|
case GPIO_PORTG_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOG;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTH_BASE:
|
|
case GPIO_PORTH_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOH;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTJ_BASE:
|
|
case GPIO_PORTJ_AHB_BASE:
|
|
{
|
|
lInt = INT_GPIOJ;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTK_BASE:
|
|
{
|
|
lInt = INT_GPIOK;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTL_BASE:
|
|
{
|
|
lInt = INT_GPIOL;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTM_BASE:
|
|
{
|
|
lInt = INT_GPIOM;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTN_BASE:
|
|
{
|
|
lInt = INT_GPION;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTP_BASE:
|
|
{
|
|
lInt = INT_GPIOP0;
|
|
break;
|
|
}
|
|
|
|
case GPIO_PORTQ_BASE:
|
|
{
|
|
lInt = INT_GPIOQ0;
|
|
break;
|
|
}
|
|
|
|
default:
|
|
{
|
|
return(-1);
|
|
}
|
|
}
|
|
|
|
//
|
|
// Return GPIO interrupt number.
|
|
//
|
|
return(lInt);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Sets the direction and mode of the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//! \param ulPinIO is the pin direction and/or mode.
|
|
//!
|
|
//! This function configures the specified pin(s) on the selected GPIO port
|
|
//! as either input or output under software control, or it configures the
|
|
//! pin to be under hardware control.
|
|
//!
|
|
//! The parameter \e ulPinIO is an enumerated data type that can be one of
|
|
//! the following values:
|
|
//!
|
|
//! - \b GPIO_DIR_MODE_IN
|
|
//! - \b GPIO_DIR_MODE_OUT
|
|
//! - \b GPIO_DIR_MODE_HW
|
|
//!
|
|
//! where \b GPIO_DIR_MODE_IN specifies that the pin is programmed as a
|
|
//! software controlled input, \b GPIO_DIR_MODE_OUT specifies that the pin is
|
|
//! programmed as a software controlled output, and \b GPIO_DIR_MODE_HW
|
|
//! specifies that the pin is placed under hardware control.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note GPIOPadConfigSet() must also be used to configure the corresponding
|
|
//! pad(s) in order for them to propagate the signal to/from the GPIO.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIODirModeSet(unsigned long ulPort, unsigned char ucPins,
|
|
unsigned long ulPinIO)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
ASSERT((ulPinIO == GPIO_DIR_MODE_IN) || (ulPinIO == GPIO_DIR_MODE_OUT) ||
|
|
(ulPinIO == GPIO_DIR_MODE_HW));
|
|
|
|
//
|
|
// Set the pin direction and mode.
|
|
//
|
|
HWREG(ulPort + GPIO_O_DIR) = ((ulPinIO & 1) ?
|
|
(HWREG(ulPort + GPIO_O_DIR) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_DIR) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_AFSEL) = ((ulPinIO & 2) ?
|
|
(HWREG(ulPort + GPIO_O_AFSEL) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_AFSEL) &
|
|
~(ucPins)));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the direction and mode of a pin.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPin is the pin number.
|
|
//!
|
|
//! This function gets the direction and control mode for a specified pin on
|
|
//! the selected GPIO port. The pin can be configured as either an input or
|
|
//! output under software control, or it can be under hardware control. The
|
|
//! type of control and direction are returned as an enumerated data type.
|
|
//!
|
|
//! \return Returns one of the enumerated data types described for
|
|
//! GPIODirModeSet().
|
|
//
|
|
//*****************************************************************************
|
|
unsigned long
|
|
GPIODirModeGet(unsigned long ulPort, unsigned char ucPin)
|
|
{
|
|
unsigned long ulDir, ulAFSEL;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
ASSERT(ucPin < 8);
|
|
|
|
//
|
|
// Convert from a pin number to a bit position.
|
|
//
|
|
ucPin = 1 << ucPin;
|
|
|
|
//
|
|
// Return the pin direction and mode.
|
|
//
|
|
ulDir = HWREG(ulPort + GPIO_O_DIR);
|
|
ulAFSEL = HWREG(ulPort + GPIO_O_AFSEL);
|
|
return(((ulDir & ucPin) ? 1 : 0) | ((ulAFSEL & ucPin) ? 2 : 0));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Sets the interrupt type for the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//! \param ulIntType specifies the type of interrupt trigger mechanism.
|
|
//!
|
|
//! This function sets up the various interrupt trigger mechanisms for the
|
|
//! specified pin(s) on the selected GPIO port.
|
|
//!
|
|
//! The parameter \e ulIntType is an enumerated data type that can be one of
|
|
//! the following values:
|
|
//!
|
|
//! - \b GPIO_FALLING_EDGE
|
|
//! - \b GPIO_RISING_EDGE
|
|
//! - \b GPIO_BOTH_EDGES
|
|
//! - \b GPIO_LOW_LEVEL
|
|
//! - \b GPIO_HIGH_LEVEL
|
|
//! - \b GPIO_DISCRETE_INT
|
|
//!
|
|
//! where the different values describe the interrupt detection mechanism
|
|
//! (edge or level) and the particular triggering event (falling, rising,
|
|
//! or both edges for edge detect, low or high for level detect).
|
|
//!
|
|
//! Some devices also support discrete interrupts for each pin on a GPIO port,
|
|
//! giving each pin a separate interrupt vector. To use this feature, the
|
|
//! \b GPIO_DISCRETE_INT can be included to enable an interrupt per pin. The
|
|
//! \b GPIO_DISCRETE_INT is not available on all devices or all GPIO ports,
|
|
//! consult the data sheet to ensure that the device and the GPIO port supports
|
|
//! discrete interrupts.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note In order to avoid any spurious interrupts, the user must
|
|
//! ensure that the GPIO inputs remain stable for the duration of
|
|
//! this function.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOIntTypeSet(unsigned long ulPort, unsigned char ucPins,
|
|
unsigned long ulIntType)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
ASSERT((ulIntType == GPIO_FALLING_EDGE) ||
|
|
(ulIntType == GPIO_RISING_EDGE) || (ulIntType == GPIO_BOTH_EDGES) ||
|
|
(ulIntType == GPIO_LOW_LEVEL) || (ulIntType == GPIO_HIGH_LEVEL));
|
|
|
|
//
|
|
// Set the pin interrupt type.
|
|
//
|
|
HWREG(ulPort + GPIO_O_IBE) = ((ulIntType & 1) ?
|
|
(HWREG(ulPort + GPIO_O_IBE) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_IBE) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_IS) = ((ulIntType & 2) ?
|
|
(HWREG(ulPort + GPIO_O_IS) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_IS) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_IEV) = ((ulIntType & 4) ?
|
|
(HWREG(ulPort + GPIO_O_IEV) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_IEV) & ~(ucPins)));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the interrupt type for a pin.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPin is the pin number.
|
|
//!
|
|
//! This function gets the interrupt type for a specified pin on the selected
|
|
//! GPIO port. The pin can be configured as a falling-edge, rising-edge, or
|
|
//! both-edges detected interrupt, or it can be configured as a low-level or
|
|
//! high-level detected interrupt. The type of interrupt detection mechanism
|
|
//! is returned as an enumerated data type.
|
|
//!
|
|
//! \return Returns one of the enumerated data types described for
|
|
//! GPIOIntTypeSet().
|
|
//
|
|
//*****************************************************************************
|
|
unsigned long
|
|
GPIOIntTypeGet(unsigned long ulPort, unsigned char ucPin)
|
|
{
|
|
unsigned long ulIBE, ulIS, ulIEV;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
ASSERT(ucPin < 8);
|
|
|
|
//
|
|
// Convert from a pin number to a bit position.
|
|
//
|
|
ucPin = 1 << ucPin;
|
|
|
|
//
|
|
// Return the pin interrupt type.
|
|
//
|
|
ulIBE = HWREG(ulPort + GPIO_O_IBE);
|
|
ulIS = HWREG(ulPort + GPIO_O_IS);
|
|
ulIEV = HWREG(ulPort + GPIO_O_IEV);
|
|
return(((ulIBE & ucPin) ? 1 : 0) | ((ulIS & ucPin) ? 2 : 0) |
|
|
((ulIEV & ucPin) ? 4 : 0));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Sets the pad configuration for the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//! \param ulStrength specifies the output drive strength.
|
|
//! \param ulPinType specifies the pin type.
|
|
//!
|
|
//! This function sets the drive strength and type for the specified pin(s)
|
|
//! on the selected GPIO port. For pin(s) configured as input ports, the
|
|
//! pad is configured as requested, but the only real effect on the input
|
|
//! is the configuration of the pull-up or pull-down termination.
|
|
//!
|
|
//! The parameter \e ulStrength can be one of the following values:
|
|
//!
|
|
//! - \b GPIO_STRENGTH_2MA
|
|
//! - \b GPIO_STRENGTH_4MA
|
|
//! - \b GPIO_STRENGTH_8MA
|
|
//! - \b GPIO_STRENGTH_8MA_SC
|
|
//!
|
|
//! where \b GPIO_STRENGTH_xMA specifies either 2, 4, or 8 mA output drive
|
|
//! strength, and \b GPIO_OUT_STRENGTH_8MA_SC specifies 8 mA output drive with
|
|
//! slew control.
|
|
//!
|
|
//! The parameter \e ulPinType can be one of the following values:
|
|
//!
|
|
//! - \b GPIO_PIN_TYPE_STD
|
|
//! - \b GPIO_PIN_TYPE_STD_WPU
|
|
//! - \b GPIO_PIN_TYPE_STD_WPD
|
|
//! - \b GPIO_PIN_TYPE_OD
|
|
//! - \b GPIO_PIN_TYPE_OD_WPU
|
|
//! - \b GPIO_PIN_TYPE_OD_WPD
|
|
//! - \b GPIO_PIN_TYPE_ANALOG
|
|
//!
|
|
//! where \b GPIO_PIN_TYPE_STD* specifies a push-pull pin, \b GPIO_PIN_TYPE_OD*
|
|
//! specifies an open-drain pin, \b *_WPU specifies a weak pull-up, \b *_WPD
|
|
//! specifies a weak pull-down, and \b GPIO_PIN_TYPE_ANALOG specifies an
|
|
//! analog input.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPadConfigSet(unsigned long ulPort, unsigned char ucPins,
|
|
unsigned long ulStrength, unsigned long ulPinType)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
ASSERT((ulStrength == GPIO_STRENGTH_2MA) ||
|
|
(ulStrength == GPIO_STRENGTH_4MA) ||
|
|
(ulStrength == GPIO_STRENGTH_8MA) ||
|
|
(ulStrength == GPIO_STRENGTH_8MA_SC));
|
|
ASSERT((ulPinType == GPIO_PIN_TYPE_STD) ||
|
|
(ulPinType == GPIO_PIN_TYPE_STD_WPU) ||
|
|
(ulPinType == GPIO_PIN_TYPE_STD_WPD) ||
|
|
(ulPinType == GPIO_PIN_TYPE_OD) ||
|
|
(ulPinType == GPIO_PIN_TYPE_OD_WPU) ||
|
|
(ulPinType == GPIO_PIN_TYPE_OD_WPD) ||
|
|
(ulPinType == GPIO_PIN_TYPE_ANALOG))
|
|
|
|
//
|
|
// Set the output drive strength.
|
|
//
|
|
HWREG(ulPort + GPIO_O_DR2R) = ((ulStrength & 1) ?
|
|
(HWREG(ulPort + GPIO_O_DR2R) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_DR2R) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_DR4R) = ((ulStrength & 2) ?
|
|
(HWREG(ulPort + GPIO_O_DR4R) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_DR4R) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_DR8R) = ((ulStrength & 4) ?
|
|
(HWREG(ulPort + GPIO_O_DR8R) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_DR8R) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_SLR) = ((ulStrength & 8) ?
|
|
(HWREG(ulPort + GPIO_O_SLR) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_SLR) & ~(ucPins)));
|
|
|
|
//
|
|
// Set the pin type.
|
|
//
|
|
HWREG(ulPort + GPIO_O_ODR) = ((ulPinType & 1) ?
|
|
(HWREG(ulPort + GPIO_O_ODR) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_ODR) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_PUR) = ((ulPinType & 2) ?
|
|
(HWREG(ulPort + GPIO_O_PUR) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_PUR) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_PDR) = ((ulPinType & 4) ?
|
|
(HWREG(ulPort + GPIO_O_PDR) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_PDR) & ~(ucPins)));
|
|
HWREG(ulPort + GPIO_O_DEN) = ((ulPinType & 8) ?
|
|
(HWREG(ulPort + GPIO_O_DEN) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_DEN) & ~(ucPins)));
|
|
|
|
//
|
|
// Set the analog mode select register. This register only appears in
|
|
// DustDevil-class (and later) devices, but is a harmless write on
|
|
// Sandstorm- and Fury-class devices.
|
|
//
|
|
HWREG(ulPort + GPIO_O_AMSEL) =
|
|
((ulPinType == GPIO_PIN_TYPE_ANALOG) ?
|
|
(HWREG(ulPort + GPIO_O_AMSEL) | ucPins) :
|
|
(HWREG(ulPort + GPIO_O_AMSEL) & ~(ucPins)));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets the pad configuration for a pin.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPin is the pin number.
|
|
//! \param pulStrength is a pointer to storage for the output drive strength.
|
|
//! \param pulPinType is a pointer to storage for the output drive type.
|
|
//!
|
|
//! This function gets the pad configuration for a specified pin on the
|
|
//! selected GPIO port. The values returned in \e pulStrength and
|
|
//! \e pulPinType correspond to the values used in GPIOPadConfigSet(). This
|
|
//! function also works for pin(s) configured as input pin(s); however, the
|
|
//! only meaningful data returned is whether the pin is terminated with a
|
|
//! pull-up or down resistor.
|
|
//!
|
|
//! \return None
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPadConfigGet(unsigned long ulPort, unsigned char ucPin,
|
|
unsigned long *pulStrength, unsigned long *pulPinType)
|
|
{
|
|
unsigned long ulTemp1, ulTemp2, ulTemp3, ulTemp4;
|
|
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
ASSERT(ucPin < 8);
|
|
|
|
//
|
|
// Convert from a pin number to a bit position.
|
|
//
|
|
ucPin = (1 << ucPin);
|
|
|
|
//
|
|
// Get the drive strength for this pin.
|
|
//
|
|
ulTemp1 = HWREG(ulPort + GPIO_O_DR2R);
|
|
ulTemp2 = HWREG(ulPort + GPIO_O_DR4R);
|
|
ulTemp3 = HWREG(ulPort + GPIO_O_DR8R);
|
|
ulTemp4 = HWREG(ulPort + GPIO_O_SLR);
|
|
*pulStrength = (((ulTemp1 & ucPin) ? 1 : 0) | ((ulTemp2 & ucPin) ? 2 : 0) |
|
|
((ulTemp3 & ucPin) ? 4 : 0) | ((ulTemp4 & ucPin) ? 8 : 0));
|
|
|
|
//
|
|
// Get the pin type.
|
|
//
|
|
ulTemp1 = HWREG(ulPort + GPIO_O_ODR);
|
|
ulTemp2 = HWREG(ulPort + GPIO_O_PUR);
|
|
ulTemp3 = HWREG(ulPort + GPIO_O_PDR);
|
|
ulTemp4 = HWREG(ulPort + GPIO_O_DEN);
|
|
*pulPinType = (((ulTemp1 & ucPin) ? 1 : 0) | ((ulTemp2 & ucPin) ? 2 : 0) |
|
|
((ulTemp3 & ucPin) ? 4 : 0) | ((ulTemp4 & ucPin) ? 8 : 0));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Enables interrupts for the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! Unmasks the interrupt for the specified pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinIntEnable(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Enable the interrupts.
|
|
//
|
|
HWREG(ulPort + GPIO_O_IM) |= ucPins;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Disables interrupts for the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! Masks the interrupt for the specified pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinIntDisable(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Disable the interrupts.
|
|
//
|
|
HWREG(ulPort + GPIO_O_IM) &= ~(ucPins);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Gets interrupt status for the specified GPIO port.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param bMasked specifies whether masked or raw interrupt status is
|
|
//! returned.
|
|
//!
|
|
//! If \e bMasked is set as \b true, then the masked interrupt status is
|
|
//! returned; otherwise, the raw interrupt status is returned.
|
|
//!
|
|
//! \return Returns a bit-packed byte, where each bit that is set identifies
|
|
//! an active masked or raw interrupt, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//! Bits 31:8 should be ignored.
|
|
//
|
|
//*****************************************************************************
|
|
long
|
|
GPIOPinIntStatus(unsigned long ulPort, tBoolean bMasked)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Return the interrupt status.
|
|
//
|
|
if(bMasked)
|
|
{
|
|
return(HWREG(ulPort + GPIO_O_MIS));
|
|
}
|
|
else
|
|
{
|
|
return(HWREG(ulPort + GPIO_O_RIS));
|
|
}
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Clears the interrupt for the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! Clears the interrupt for the specified pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note Because there is a write buffer in the Cortex-M3 processor, it may
|
|
//! take several clock cycles before the interrupt source is actually cleared.
|
|
//! Therefore, it is recommended that the interrupt source be cleared early in
|
|
//! the interrupt handler (as opposed to the very last action) to avoid
|
|
//! returning from the interrupt handler before the interrupt source is
|
|
//! actually cleared. Failure to do so may result in the interrupt handler
|
|
//! being immediately reentered (because the interrupt controller still sees
|
|
//! the interrupt source asserted).
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinIntClear(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Clear the interrupts.
|
|
//
|
|
HWREG(ulPort + GPIO_O_ICR) = ucPins;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Registers an interrupt handler for a GPIO port.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param pfnIntHandler is a pointer to the GPIO port interrupt handling
|
|
//! function.
|
|
//!
|
|
//! This function ensures that the interrupt handler specified by
|
|
//! \e pfnIntHandler is called when an interrupt is detected from the selected
|
|
//! GPIO port. This function also enables the corresponding GPIO interrupt
|
|
//! in the interrupt controller; individual pin interrupts and interrupt
|
|
//! sources must be enabled with GPIOPinIntEnable().
|
|
//!
|
|
//! \sa IntRegister() for important information about registering interrupt
|
|
//! handlers.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPortIntRegister(unsigned long ulPort, void (*pfnIntHandler)(void))
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Get the interrupt number associated with the specified GPIO.
|
|
//
|
|
ulPort = GPIOGetIntNumber(ulPort);
|
|
|
|
//
|
|
// Register the interrupt handler.
|
|
//
|
|
IntRegister(ulPort, pfnIntHandler);
|
|
|
|
//
|
|
// Enable the GPIO interrupt.
|
|
//
|
|
IntEnable(ulPort);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Removes an interrupt handler for a GPIO port.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//!
|
|
//! This function unregisters the interrupt handler for the specified
|
|
//! GPIO port. This function also disables the corresponding
|
|
//! GPIO port interrupt in the interrupt controller; individual GPIO interrupts
|
|
//! and interrupt sources must be disabled with GPIOPinIntDisable().
|
|
//!
|
|
//! \sa IntRegister() for important information about registering interrupt
|
|
//! handlers.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPortIntUnregister(unsigned long ulPort)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Get the interrupt number associated with the specified GPIO.
|
|
//
|
|
ulPort = GPIOGetIntNumber(ulPort);
|
|
|
|
//
|
|
// Disable the GPIO interrupt.
|
|
//
|
|
IntDisable(ulPort);
|
|
|
|
//
|
|
// Unregister the interrupt handler.
|
|
//
|
|
IntUnregister(ulPort);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Reads the values present of the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The values at the specified pin(s) are read, as specified by \e ucPins.
|
|
//! Values are returned for both input and output pin(s), and the value
|
|
//! for pin(s) that are not specified by \e ucPins are set to 0.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \return Returns a bit-packed byte providing the state of the specified
|
|
//! pin, where bit 0 of the byte represents GPIO port pin 0, bit 1 represents
|
|
//! GPIO port pin 1, and so on. Any bit that is not specified by \e ucPins
|
|
//! is returned as a 0. Bits 31:8 should be ignored.
|
|
//
|
|
//*****************************************************************************
|
|
long
|
|
GPIOPinRead(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Return the pin value(s).
|
|
//
|
|
return(HWREG(ulPort + (GPIO_O_DATA + (ucPins << 2))));
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Writes a value to the specified pin(s).
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//! \param ucVal is the value to write to the pin(s).
|
|
//!
|
|
//! Writes the corresponding bit values to the output pin(s) specified by
|
|
//! \e ucPins. Writing to a pin configured as an input pin has no effect.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinWrite(unsigned long ulPort, unsigned char ucPins, unsigned char ucVal)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Write the pins.
|
|
//
|
|
HWREG(ulPort + (GPIO_O_DATA + (ucPins << 2))) = ucVal;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as analog-to-digital converter inputs.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The analog-to-digital converter input pins must be properly configured
|
|
//! to function correctly on devices that are not Sandstorm- or Fury-class.
|
|
//! This function provides the proper configuration for those pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into an ADC input; it
|
|
//! only configures an ADC input pin for proper operation. Devices with
|
|
//! flexible pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeADC(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
|
|
|
|
//
|
|
// Set the pad(s) for analog operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as a CAN device.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The CAN pins must be properly configured for the CAN peripherals to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! those pin(s); other configurations may work as well depending upon the
|
|
//! board setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a CAN pin; it only
|
|
//! configures a CAN pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeCAN(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as an analog comparator input.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The analog comparator input pins must be properly configured for the analog
|
|
//! comparator to function correctly. This function provides the proper
|
|
//! configuration for those pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into an analog comparator
|
|
//! input; it only configures an analog comparator pin for proper operation.
|
|
//! Devices with flexible pin muxing also require a GPIOPinConfigure()
|
|
//! function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeComparator(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
|
|
|
|
//
|
|
// Set the pad(s) for analog operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the external peripheral interface.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The external peripheral interface pins must be properly configured for the
|
|
//! external peripheral interface to function correctly. This function
|
|
//! provides a typical configuration for those pin(s); other configurations may
|
|
//! work as well depending upon the board setup (for example, using the on-chip
|
|
//! pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into an external
|
|
//! peripheral interface pin; it only configures an external peripheral
|
|
//! interface pin for proper operation. Devices with flexible pin muxing also
|
|
//! require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeEPI(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the Ethernet peripheral as LED signals.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The Ethernet peripheral provides two signals that can be used to drive
|
|
//! an LED (e.g. for link status/activity). This function provides a typical
|
|
//! configuration for the pins.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into an Ethernet LED pin;
|
|
//! it only configures an Ethernet LED pin for proper operation. Devices with
|
|
//! flexible pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeEthernetLED(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the Ethernet peripheral as MII signals.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The Ethernet peripheral on some parts provides a set of MII signals that
|
|
//! are used to connect to an external PHY. This function provides a typical
|
|
//! configuration for the pins.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into an Ethernet MII pin;
|
|
//! it only configures an Ethernet MII pin for proper operation. Devices with
|
|
//! flexible pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeEthernetMII(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the fan module.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The fan pins must be properly configured for the fan controller to function
|
|
//! correctly. This function provides a typical configuration for those
|
|
//! pin(s); other configurations may work as well depending upon the board
|
|
//! setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a fan pin; it only
|
|
//! configures a fan pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeFan(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as GPIO inputs.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The GPIO pins must be properly configured in order to function correctly as
|
|
//! GPIO inputs; this is especially true of Fury-class devices where the
|
|
//! digital input enable is turned off by default. This function provides the
|
|
//! proper configuration for those pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note Devices with flexible pin muxing also require a GPIOPinConfigure()
|
|
//! function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeGPIOInput(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as GPIO outputs.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The GPIO pins must be properly configured in order to function correctly as
|
|
//! GPIO outputs; this is especially true of Fury-class devices where the
|
|
//! digital input enable is turned off by default. This function provides the
|
|
//! proper configuration for those pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note Devices with flexible pin muxing also require a GPIOPinConfigure()
|
|
//! function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeGPIOOutput(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
|
|
//
|
|
// Make the pin(s) be outputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_OUT);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as GPIO open drain outputs.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The GPIO pins must be properly configured in order to function correctly as
|
|
//! GPIO outputs; this is especially true of Fury-class devices where the
|
|
//! digital input enable is turned off by default. This function provides the
|
|
//! proper configuration for those pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note Devices with flexible pin muxing also require a GPIOPinConfigure()
|
|
//! function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeGPIOOutputOD(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_OD);
|
|
|
|
//
|
|
// Make the pin(s) be outputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_OUT);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the I2C peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The I2C pins must be properly configured for the I2C peripheral to function
|
|
//! correctly. This function provides the proper configuration for those
|
|
//! pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into an I2C pin; it
|
|
//! only configures an I2C pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeI2C(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for open-drain operation with a weak pull-up.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_OD_WPU);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use as SCL by the I2C peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The I2C pins must be properly configured for the I2C peripheral to function
|
|
//! correctly. This function provides the proper configuration for the SCL
|
|
//! pin(s).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function should only be used for Blizzard-class devices. It
|
|
//! cannot be used to turn any pin into an I2C SCL pin; it only configures an
|
|
//! I2C SCL pin for proper operation. Devices with flexible pin muxing also
|
|
//! require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeI2CSCL(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for open-drain operation with a weak pull-up.
|
|
//
|
|
if(CLASS_IS_BLIZZARD)
|
|
{
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
else
|
|
{
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_OD);
|
|
}
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the I2S peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! Some I2S pins must be properly configured for the I2S peripheral to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! the digital I2S pin(s); other configurations may work as well depending
|
|
//! upon the board setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a I2S pin; it only
|
|
//! configures a I2S pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeI2S(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the LPC module.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The LPC pins must be properly configured for the LPC module to function
|
|
//! correctly. This function provides a typical configuration for those
|
|
//! pin(s); other configurations may work as well depending upon the board
|
|
//! setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a LPC pin; it only
|
|
//! configures a LPC pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeLPC(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_8MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures a pin for receive use by the PECI module.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The PECI receive pin must be properly configured for the PECI module to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! that pin.
|
|
//!
|
|
//! The pin is specified using a bit-packed byte, where each bit that is set
|
|
//! identifies the pin to be accessed, and where bit 0 of the byte represents
|
|
//! GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a PECI receive pin;
|
|
//! it only configures a PECI receive pin for proper operation. Devices with
|
|
//! flexible pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypePECIRx(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
|
|
|
|
//
|
|
// Set the pad(s) for analog operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures a pin for transmit use by the PECI module.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The PECI transmit pin must be properly configured for the PECI module to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! that pin.
|
|
//!
|
|
//! The pin is specified using a bit-packed byte, where each bit that is set
|
|
//! identifies the pin to be accessed, and where bit 0 of the byte represents
|
|
//! GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a PECI transmit pin;
|
|
//! it only configures a PECI transmit pin for proper operation. Devices with
|
|
//! flexible pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypePECITx(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for analog operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the PWM peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The PWM pins must be properly configured for the PWM peripheral to function
|
|
//! correctly. This function provides a typical configuration for those
|
|
//! pin(s); other configurations may work as well depending upon the board
|
|
//! setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a PWM pin; it only
|
|
//! configures a PWM pin for proper operation. Devices wtih flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypePWM(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the QEI peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The QEI pins must be properly configured for the QEI peripheral to function
|
|
//! correctly. This function provides a typical configuration for those
|
|
//! pin(s); other configurations may work as well depending upon the board
|
|
//! setup (for example, not using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a QEI pin; it only
|
|
//! configures a QEI pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeQEI(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation with a weak pull-up.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD_WPU);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the SSI peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The SSI pins must be properly configured for the SSI peripheral to function
|
|
//! correctly. This function provides a typical configuration for those
|
|
//! pin(s); other configurations may work as well depending upon the board
|
|
//! setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a SSI pin; it only
|
|
//! configures a SSI pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeSSI(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the Timer peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The CCP pins must be properly configured for the timer peripheral to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! those pin(s); other configurations may work as well depending upon the
|
|
//! board setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a timer pin; it
|
|
//! only configures a timer pin for proper operation. Devices with flexible
|
|
//! pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeTimer(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the UART peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! The UART pins must be properly configured for the UART peripheral to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! those pin(s); other configurations may work as well depending upon the
|
|
//! board setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a UART pin; it
|
|
//! only configures a UART pin for proper operation. Devices with flexible
|
|
//! pin muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeUART(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the USB peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! Some USB analog pins must be properly configured for the USB peripheral to
|
|
//! function correctly. This function provides the proper configuration for
|
|
//! any USB pin(s). This can also be used to configure the EPEN and PFAULT pins
|
|
//! so that they are no longer used by the USB controller.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a USB pin; it only
|
|
//! configures a USB pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeUSBAnalog(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be inputs.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_IN);
|
|
|
|
//
|
|
// Set the pad(s) for analog operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_ANALOG);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures pin(s) for use by the USB peripheral.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! Some USB digital pins must be properly configured for the USB peripheral to
|
|
//! function correctly. This function provides a typical configuration for
|
|
//! the digital USB pin(s); other configurations may work as well depending
|
|
//! upon the board setup (for example, using the on-chip pull-ups).
|
|
//!
|
|
//! This function should only be used with EPEN and PFAULT pins as all other
|
|
//! USB pins are analog in nature or are not used in devices without OTG
|
|
//! functionality.
|
|
//!
|
|
//! The pin(s) are specified using a bit-packed byte, where each bit that is
|
|
//! set identifies the pin to be accessed, and where bit 0 of the byte
|
|
//! represents GPIO port pin 0, bit 1 represents GPIO port pin 1, and so on.
|
|
//!
|
|
//! \note This function cannot be used to turn any pin into a USB pin; it only
|
|
//! configures a USB pin for proper operation. Devices with flexible pin
|
|
//! muxing also require a GPIOPinConfigure() function call.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinTypeUSBDigital(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Make the pin(s) be peripheral controlled.
|
|
//
|
|
GPIODirModeSet(ulPort, ucPins, GPIO_DIR_MODE_HW);
|
|
|
|
//
|
|
// Set the pad(s) for standard push-pull operation.
|
|
//
|
|
GPIOPadConfigSet(ulPort, ucPins, GPIO_STRENGTH_2MA, GPIO_PIN_TYPE_STD);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Configures the alternate function of a GPIO pin.
|
|
//!
|
|
//! \param ulPinConfig is the pin configuration value, specified as only one of
|
|
//! the \b GPIO_P??_??? values.
|
|
//!
|
|
//! This function configures the pin mux that selects the peripheral function
|
|
//! associated with a particular GPIO pin. Only one peripheral function at a
|
|
//! time can be associated with a GPIO pin, and each peripheral function should
|
|
//! only be associated with a single GPIO pin at a time (despite the fact that
|
|
//! many of them can be associated with more than one GPIO pin). To fully
|
|
//! configure a pin, a GPIOPinType*() function should also be called.
|
|
//!
|
|
//! The available mappings are supplied on a per-device basis in
|
|
//! <tt>pin_map.h</tt>. The \b PART_IS_<partno> define enables the
|
|
//! appropriate set of defines for the device that is being used.
|
|
//!
|
|
//! \note This function is not valid on Sandstorm, Fury, and Dustdevil-class
|
|
//! devices.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOPinConfigure(unsigned long ulPinConfig)
|
|
{
|
|
unsigned long ulBase, ulShift;
|
|
|
|
//
|
|
// Check the argument.
|
|
//
|
|
ASSERT(((ulPinConfig >> 16) & 0xff) < 15);
|
|
ASSERT(((ulPinConfig >> 8) & 0xe3) == 0);
|
|
|
|
//
|
|
// Extract the base address index from the input value.
|
|
//
|
|
ulBase = (ulPinConfig >> 16) & 0xff;
|
|
|
|
//
|
|
// Get the base address of the GPIO module, selecting either the APB or the
|
|
// AHB aperture as appropriate.
|
|
//
|
|
if(HWREG(SYSCTL_GPIOHBCTL) & (1 << ulBase))
|
|
{
|
|
ulBase = g_pulGPIOBaseAddrs[(ulBase << 1) + 1];
|
|
}
|
|
else
|
|
{
|
|
ulBase = g_pulGPIOBaseAddrs[ulBase << 1];
|
|
}
|
|
|
|
//
|
|
// Extract the shift from the input value.
|
|
//
|
|
ulShift = (ulPinConfig >> 8) & 0xff;
|
|
|
|
//
|
|
// Write the requested pin muxing value for this GPIO pin.
|
|
//
|
|
HWREG(ulBase + GPIO_O_PCTL) = ((HWREG(ulBase + GPIO_O_PCTL) &
|
|
~(0xf << ulShift)) |
|
|
((ulPinConfig & 0xf) << ulShift));
|
|
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Enables a GPIO pin as a trigger to start a DMA transaction.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! This function enables a GPIO pin to be used as a trigger to start a uDMA
|
|
//! transaction. Any GPIO pin can be configured to be an external trigger for
|
|
//! the uDMA. The GPIO pin still generates interrupts if the interrupt is
|
|
//! enabled for the selected pin.
|
|
//!
|
|
//! \note This function is not available on all devices, consult the data sheet
|
|
//! to ensure that the device you are using supports GPIO DMA Control.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIODMATriggerEnable(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Set the pin as a DMA trigger.
|
|
//
|
|
HWREG(ulPort + GPIO_O_DMACTL) |= ucPins;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Disables a GPIO pin as a trigger to start a DMA transaction.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! This function disables a GPIO pin from being used as a trigger to start a
|
|
//! uDMA transaction. This function can be used to disable this feature if it
|
|
//! was enabled via a call to GPIODMATriggerEnable().
|
|
//!
|
|
//! \note This function is not available on all devices, consult the data sheet
|
|
//! to ensure that the device you are using supports GPIO DMA Control.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIODMATriggerDisable(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Set the pin as a DMA trigger.
|
|
//
|
|
HWREG(ulPort + GPIO_O_DMACTL) &= (~ucPins);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Enables a GPIO pin as a trigger to start an ADC capture.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! This function enables a GPIO pin to be used as a trigger to start an ADC
|
|
//! sequence. Any GPIO pin can be configured to be an external trigger for
|
|
//! an ADC sequence. The GPIO pin still generates interrupts if the
|
|
//! interrupt is enabled for the selected pin. To enable the use of a GPIO pin
|
|
//! to trigger the ADC module, the ADCSequenceConfigure() function must be called
|
|
//! with the ADC_TRIGGER_EXTERNAL parameter.
|
|
//!
|
|
//! \note This function is not available on all devices, consult the data sheet
|
|
//! to ensure that the device you are using supports GPIO ADC Control.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOADCTriggerEnable(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Set the pin as a DMA trigger.
|
|
//
|
|
HWREG(ulPort + GPIO_O_ADCCTL) |= ucPins;
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
//! Disable a GPIO pin as a trigger to start an ADC capture.
|
|
//!
|
|
//! \param ulPort is the base address of the GPIO port.
|
|
//! \param ucPins is the bit-packed representation of the pin(s).
|
|
//!
|
|
//! This function disables a GPIO pin to be used as a trigger to start an ADC
|
|
//! sequence. This function can be used to disable this feature if it was
|
|
//! enabled via a call to GPIOADCTriggerEnable().
|
|
//!
|
|
//! \note This function is not available on all devices, consult the data sheet
|
|
//! to ensure that the device you are using supports GPIO ADC Control.
|
|
//!
|
|
//! \return None.
|
|
//
|
|
//*****************************************************************************
|
|
void
|
|
GPIOADCTriggerDisable(unsigned long ulPort, unsigned char ucPins)
|
|
{
|
|
//
|
|
// Check the arguments.
|
|
//
|
|
ASSERT(GPIOBaseValid(ulPort));
|
|
|
|
//
|
|
// Set the pin as a DMA trigger.
|
|
//
|
|
HWREG(ulPort + GPIO_O_ADCCTL) &= (~ucPins);
|
|
}
|
|
|
|
//*****************************************************************************
|
|
//
|
|
// Close the Doxygen group.
|
|
//! @}
|
|
//
|
|
//*****************************************************************************
|