芯来科技RVSTAR开发板

简介

RVSTAR开发板 是由芯来科技公司推出的基于采用芯来科技RISC-V架构处理器芯片的GD32VF103的开发板。

更多关于 RVSTAR开发板 开发板的详细资料请参见 RVSTAR开发板快速入门

板载资源

硬件	描述
内核	Nuclei N205
架构	32-bit RV32IMAC
主频	108 MHz

工具安装

安装工具链

请根据安装Nuclei RISC-V GCC Toolchain和OpenOCD 来安装依赖的工具。

添加环境变量

将Nuclei RISC-V GCC Toolchain和OpenOCD的环境变量进行设置。

Windows

假设工具安装在 D:\Software\Nuclei目录下, 则可以修改系统环境变量PATH, 将D:\Software\Nuclei\gcc\bin;D:\Software\Nuclei\openocd\bin;增加到PATH中。

或者在ENV工具命令行中运行

set PATH=D:\Software\Nuclei\gcc\bin;D:\Software\Nuclei\openocd\bin;%PATH%

Linux

假设工具安装在 ~/Software/Nuclei目录下, 通过在Linux的.bashrc增加如下一行代码来添加环境变量。

export PATH=~/Software/Nuclei/gcc/bin:~/Software/Nuclei/openocd/bin:$PATH

或者在ENV工具命令行中运行

export PATH=~/Software/Nuclei/gcc/bin:~/Software/Nuclei/openocd/bin:$PATH

注意: 对应的RISC-V GCC和OPENOCD的路径请替换成自己安装的路径。

烧写及执行

编译程序

下载好RT-Thread的代码和ENV工具以后。

按照ENV工具的教程, 在rt-thread\bsp\nuclei\gd32vf103_rvstar目录打开ENV工具命令行。

注意: 请确保Nuclei GCC和Nuclei OpenOCD的路径设置正确无误。

运行 pkgs --update来下载最新的依赖的Nuclei SDK开发包
可选: 运行 menuconfig来进行内核配置
运行 scons -c清理之前的编译结果
运行 scons来进行代码的编译

下载程序

在保证程序能够正常编译后, 在相同ENV终端执行scons --run upload进行代码的下载。

正常下载的输出如下:

scons: Reading SConscript files ...
Supported downloaded modes for board gd32vf103v_rvstar are flashxip, chosen downloaded mode is flashxip
Upload application rtthread.elf using openocd and gdb
riscv-nuclei-elf-gdb rtthread.elf -ex "set remotetimeout 240"                     -ex "target remote | openocd --pipe -f D:/workspace/Sourcecode/rt-thread/bsp/nuclei/gd32vf103_rvstar/packages/nuclei_sdk-latest/SoC/gd32vf103/Board/gd32vf103v_rvstar/openocd_gd32vf103.cfg"                     --batch -ex "monitor halt" -ex "monitor flash protect 0 0 last off" -ex "load"                     -ex "monitor resume" -ex "monitor shutdown" -ex "quit"
D:\Software\Nuclei\gcc\bin\riscv-nuclei-elf-gdb.exe: warning: Couldn't determine a path for the index cache directory.

Nuclei OpenOCD, 64-bit Open On-Chip Debugger 0.10.0+dev-00014-g0eae03214 (2019-12-12-07:43)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.org/doc/doxygen/bugs.html
rt_thread_idle_entry (parameter=0x0) at D:\workspace\Sourcecode\rt-thread\src\idle.c:251
251                 if (idle_hook_list[i] != RT_NULL)
cleared protection for sectors 0 through 127 on flash bank 0

Loading section .init, size 0x264 lma 0x8000000
Loading section .text, size 0x140de lma 0x8000280
Loading section .rodata, size 0x37c0 lma 0x8014360
Loading section .data, size 0x404 lma 0x8017b20
Start address 0x800015c, load size 98054
Transfer rate: 8 KB/sec, 10894 bytes/write.
shutdown command invoked
A debugging session is active.

        Inferior 1 [Remote target] will be detached.

Quit anyway? (y or n) [answered Y; input not from terminal]
Remote communication error.  Target disconnected.: Success.

下载程序之后, 连接串口(115200-N-8-1), 可以看到 RT-Thread 的输出信息：

initialize rti_board_start:0 done

 \ | /
- RT -     Thread Operating System
 / | \     4.0.3 build Apr  9 2020
 2006 - 2020 Copyright by rt-thread team
do components initialization.
initialize rti_board_end:0 done
initialize dfs_init:0 done
initialize libc_system_init:0 done
initialize finsh_system_init:0 done
msh />

在串口终端(我这里使用的是TeraTerm)输入ps即可查看当前线程工作情况:

msh />ps
thread   pri  status      sp     stack size max used left tick  error
-------- ---  ------- ---------- ----------  ------  ---------- ---
thread01  19  suspend 0x00000158 0x0000018c    87%   0x00000005 000
thread00  19  suspend 0x00000158 0x0000018c    87%   0x00000005 000
tshell    20  running 0x00000258 0x00001000    18%   0x00000004 000
tidle0    31  ready   0x000000a8 0x0000018c    59%   0x0000000e 000
timer      4  suspend 0x000000f8 0x00000200    49%   0x00000009 000
main      10  suspend 0x00000168 0x00000800    36%   0x00000006 000
msh />

调试程序

在保证程序编译成功后, 在相同ENV终端执行scons --run debug进行代码在命令行下进行GDB调试。

正常的调试输出如下：

scons: Reading SConscript files ...
Supported downloaded modes for board gd32vf103v_rvstar are flashxip, chosen downloaded mode is flashxip
Debug application rtthread.elf using openocd and gdb
riscv-nuclei-elf-gdb rtthread.elf -ex "set remotetimeout 240"                     -ex "target remote | openocd --pipe -f D:/workspace/Sourcecode/rt-thread/bsp/nuclei/gd32vf103_rvstar/packages/nuclei_sdk-latest/SoC/gd32vf103/Board/gd32vf103v_rvstar/openocd_gd32vf103.cfg"
D:\Software\Nuclei\gcc\bin\riscv-nuclei-elf-gdb.exe: warning: Couldn't determine a path for the index cache directory.
GNU gdb (GDB) 8.3.0.20190516-git
Copyright (C) 2019 Free Software Foundation, Inc.
License GPLv3+: GNU GPL version 3 or later <http://gnu.org/licenses/gpl.html>
This is free software: you are free to change and redistribute it.
There is NO WARRANTY, to the extent permitted by law.
Type "show copying" and "show warranty" for details.
This GDB was configured as "--host=i686-w64-mingw32 --target=riscv-nuclei-elf".
Type "show configuration" for configuration details.
For bug reporting instructions, please see:
<http://www.gnu.org/software/gdb/bugs/>.
Find the GDB manual and other documentation resources online at:
    <http://www.gnu.org/software/gdb/documentation/>.

For help, type "help".
Type "apropos word" to search for commands related to "word"...
Reading symbols from rtthread.elf...
Remote debugging using | openocd --pipe -f D:/workspace/Sourcecode/rt-thread/bsp/nuclei/gd32vf103_rvstar/packages/nuclei_sdk-latest/SoC/gd32vf103/Board/gd32vf103v_rvstar/openocd_gd32vf103.cfg Nuclei OpenOCD, 64-bit Open On-Chip Debugger 0.10.0+dev-00014-g0eae03214 (2019-12-12-07:43)
Licensed under GNU GPL v2
For bug reports, read
        http://openocd.org/doc/doxygen/bugs.html
rt_thread_idle_entry (parameter=0x0) at D:\workspace\Sourcecode\rt-thread\src\idle.c:249
249             for (i = 0; i < RT_IDLE_HOOK_LIST_SIZE; i++)
(gdb)
(gdb) b main.c:35
Breakpoint 1 at 0x8000290: file applications\main.c, line 35.
(gdb) c
Continuing.
Note: automatically using hardware breakpoints for read-only addresses.

Breakpoint 1, thread_entry (parameter=0x0) at applications\main.c:35
35              rt_thread_mdelay(500);
(gdb)

调试例子参见如下文档:

https://doc.nucleisys.com/nuclei_sdk/quickstart.html#debug-application

为了更方便的进行调试, 也可以下载Nuclei Studio集成开发环境, 创建一个Debug Configuration, 选择编译好的 ELF文件, 然后配置OPENOCD和GDB即可, OPENOCD配置文件路径为bsp\nuclei\gd32vf103_rvstar\packages\nuclei_sdk-latest\SoC\gd32vf103\Board\gd32vf103v_rvstar\openocd_gd32vf103.cfg

驱动支持情况

驱动	支持情况	备注
UART	支持	RV-STAR板载串口是UART4

注:

适配RT-Thread的驱动框架的代码在 ../libraries/gd32vf103/HAL_Drivers目录下。
如果有开发者想适配更多的驱动, 请在对应目录下增加驱动适配支持。

联系人信息

维护人：

fanghuaqi

8.3 KiB

Raw Blame History

芯来科技RVSTAR开发板

简介

板载资源

工具安装

安装工具链

添加环境变量

Windows

Linux

烧写及执行

驱动设置

编译程序

下载程序

调试程序

驱动支持情况

联系人信息

8.3 KiB Raw Blame History

芯来科技RVSTAR开发板

简介

板载资源

工具安装

安装工具链

添加环境变量

Windows

Linux

烧写及执行

驱动设置

编译程序

下载程序

调试程序

驱动支持情况

联系人信息

8.3 KiB

Raw Blame History