libs/rt-thread
libs
/
rt-thread
4
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
rt-thread/bsp/lm4f232/Libraries/driverlib/can.c

2251 lines
71 KiB
C
Raw Blame History

//*****************************************************************************
//
// can.c - Driver for the CAN module.
//
// Copyright (c) 2006-2011 Texas Instruments Incorporated. All rights reserved.
// Software License Agreement
//
// Texas Instruments (TI) is supplying this software for use solely and
// exclusively on TI's microcontroller products. The software is owned by
// TI and/or its suppliers, and is protected under applicable copyright
// laws. You may not combine this software with "viral" open-source
// software in order to form a larger program.
//
// THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS.
// NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT
// NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY
// CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL
// DAMAGES, FOR ANY REASON WHATSOEVER.
//
// This is part of revision 8264 of the Stellaris Peripheral Driver Library.
//
//*****************************************************************************
//*****************************************************************************
//
//! \addtogroup can_api
//! @{
//
//*****************************************************************************
#include "inc/hw_can.h"
#include "inc/hw_ints.h"
#include "inc/hw_nvic.h"
#include "inc/hw_memmap.h"
#include "inc/hw_types.h"
#include "driverlib/can.h"
#include "driverlib/debug.h"
#include "driverlib/interrupt.h"
//*****************************************************************************
//
// This is the maximum number that can be stored as an 11bit Message
// identifier.
//
//*****************************************************************************
#define CAN_MAX_11BIT_MSG_ID 0x7ff
//*****************************************************************************
//
// This is used as the loop delay for accessing the CAN controller registers.
//
//*****************************************************************************
#define CAN_RW_DELAY 5
//*****************************************************************************
//
// The maximum CAN bit timing divisor is 19.
//
//*****************************************************************************
#define CAN_MAX_BIT_DIVISOR 19
//*****************************************************************************
//
// The minimum CAN bit timing divisor is 4.
//
//*****************************************************************************
#define CAN_MIN_BIT_DIVISOR 4
//*****************************************************************************
//
// The maximum CAN pre-divisor is 1024.
//
//*****************************************************************************
#define CAN_MAX_PRE_DIVISOR 1024
//*****************************************************************************
//
// The minimum CAN pre-divisor is 1.
//
//*****************************************************************************
#define CAN_MIN_PRE_DIVISOR 1
//*****************************************************************************
//
// Converts a set of CAN bit timing values into the value that needs to be
// programmed into the CAN_BIT register to achieve those timings.
//
//*****************************************************************************
#define CAN_BIT_VALUE(seg1, seg2, sjw) \
((((seg1 - 1) << CAN_BIT_TSEG1_S) & \
CAN_BIT_TSEG1_M) | \
(((seg2 - 1) << CAN_BIT_TSEG2_S) & \
CAN_BIT_TSEG2_M) | \
(((sjw - 1) << CAN_BIT_SJW_S) & \
CAN_BIT_SJW_M))
//*****************************************************************************
//
// This table is used by the CANBitRateSet() API as the register defaults for
// the bit timing values.
//
//*****************************************************************************
static const unsigned short g_usCANBitValues[] =
{
CAN_BIT_VALUE(2, 1, 1), // 4 clocks/bit
CAN_BIT_VALUE(3, 1, 1), // 5 clocks/bit
CAN_BIT_VALUE(3, 2, 2), // 6 clocks/bit
CAN_BIT_VALUE(4, 2, 2), // 7 clocks/bit
CAN_BIT_VALUE(4, 3, 3), // 8 clocks/bit
CAN_BIT_VALUE(5, 3, 3), // 9 clocks/bit
CAN_BIT_VALUE(5, 4, 4), // 10 clocks/bit
CAN_BIT_VALUE(6, 4, 4), // 11 clocks/bit
CAN_BIT_VALUE(6, 5, 4), // 12 clocks/bit
CAN_BIT_VALUE(7, 5, 4), // 13 clocks/bit
CAN_BIT_VALUE(7, 6, 4), // 14 clocks/bit
CAN_BIT_VALUE(8, 6, 4), // 15 clocks/bit
CAN_BIT_VALUE(8, 7, 4), // 16 clocks/bit
CAN_BIT_VALUE(9, 7, 4), // 17 clocks/bit
CAN_BIT_VALUE(9, 8, 4), // 18 clocks/bit
CAN_BIT_VALUE(10, 8, 4) // 19 clocks/bit
};
//*****************************************************************************
//
//! \internal
//! Checks a CAN base address.
//!
//! \param ulBase is the base address of the CAN controller.
//!
//! This function determines if a CAN controller base address is valid.
//!
//! \return Returns \b true if the base address is valid and \b false
//! otherwise.
//
//*****************************************************************************
#ifdef DEBUG
static tBoolean
CANBaseValid(unsigned long ulBase)
{
return((ulBase == CAN0_BASE) || (ulBase == CAN1_BASE) ||
(ulBase == CAN2_BASE));
}
#endif
//*****************************************************************************
//
//! \internal
//!
//! Returns the CAN controller interrupt number.
//!
//! \param ulBase is the base address of the selected CAN controller
//!
//! Given a CAN controller base address, this function returns the
//! corresponding interrupt number.
//!
//! This function replaces the original CANGetIntNumber() API and performs the
//! same actions. A macro is provided in <tt>can.h</tt> to map the original
//! API to this API.
//!
//! \return Returns a CAN interrupt number, or -1 if \e ulPort is invalid.
//
//*****************************************************************************
static long
CANIntNumberGet(unsigned long ulBase)
{
long lIntNumber;
//
// Return the interrupt number for the given CAN controller.
//
switch(ulBase)
{
//
// Return the interrupt number for CAN 0
//
case CAN0_BASE:
{
lIntNumber = INT_CAN0;
break;
}
//
// Return the interrupt number for CAN 1
//
case CAN1_BASE:
{
lIntNumber = INT_CAN1;
break;
}
//
// Return the interrupt number for CAN 2
//
case CAN2_BASE:
{
lIntNumber = INT_CAN2;
break;
}
//
// Return -1 to indicate a bad address was passed in.
//
default:
{
lIntNumber = -1;
}
}
return(lIntNumber);
}
//*****************************************************************************
//
//! \internal
//!
//! Reads a CAN controller register.
//!
//! \param ulRegAddress is the full address of the CAN register to be read.
//!
//! This function performs the necessary synchronization to read from a CAN
//! controller register.
//!
//! This function replaces the original CANReadReg() API and performs the same
//! actions. A macro is provided in <tt>can.h</tt> to map the original API to
//! this API.
//!
//! \note This function provides the delay required to access CAN registers.
//! This delay is required when accessing CAN registers directly.
//!
//! \return Returns the value read from the register.
//
//*****************************************************************************
static unsigned long
CANRegRead(unsigned long ulRegAddress)
{
volatile unsigned long ulDelay;
unsigned long ulRetVal;
unsigned long ulIntNumber;
unsigned long ulReenableInts;
//
// Get the CAN interrupt number from the register base address.
//
ulIntNumber = CANIntNumberGet(ulRegAddress & 0xfffff000);
//
// Make sure that the CAN base address was valid.
//
ASSERT(ulIntNumber != (unsigned long)-1);
//
// Remember current state so that CAN interrupts are only re-enabled if
// they were already enabled.
//
ulReenableInts = HWREG(NVIC_EN1) & (1 << (ulIntNumber - 48));
//
// If the CAN interrupt was enabled then disable it.
//
if(ulReenableInts)
{
IntDisable(ulIntNumber);
}
//
// Trigger the initial read to the CAN controller. The value returned at
// this point is not valid.
//
HWREG(ulRegAddress);
//
// This delay is necessary for the CAN have the correct data on the bus.
//
for(ulDelay = 0; ulDelay < CAN_RW_DELAY; ulDelay++)
{
}
//
// Do the final read that has the valid value of the register.
//
ulRetVal = HWREG(ulRegAddress);
//
// Enable CAN interrupts if they were enabled before this call.
//
if(ulReenableInts)
{
IntEnable(ulIntNumber);
}
return(ulRetVal);
}
//*****************************************************************************
//
//! \internal
//!
//! Writes a CAN controller register.
//!
//! \param ulRegAddress is the full address of the CAN register to be written.
//! \param ulRegValue is the value to write into the register specified by
//! \e ulRegAddress.
//!
//! This function takes care of the synchronization necessary to write to a
//! CAN controller register.
//!
//! This function replaces the original CANWriteReg() API and performs the same
//! actions. A macro is provided in <tt>can.h</tt> to map the original API to
//! this API.
//!
//! \note The delays in this function are required when accessing CAN registers
//! directly.
//!
//! \return None.
//
//*****************************************************************************
static void
CANRegWrite(unsigned long ulRegAddress, unsigned long ulRegValue)
{
volatile unsigned long ulDelay;
//
// Trigger the initial write to the CAN controller. The value will not make
// it out to the CAN controller for CAN_RW_DELAY cycles.
//
HWREG(ulRegAddress) = ulRegValue;
//
// Delay to allow the CAN controller to receive the new data.
//
for(ulDelay = 0; ulDelay < CAN_RW_DELAY; ulDelay++)
{
}
}
//*****************************************************************************
//
//! \internal
//!
//! Copies data from a buffer to the CAN Data registers.
//!
//! \param pucData is a pointer to the data to be written out to the CAN
//! controller's data registers.
//! \param pulRegister is an unsigned long pointer to the first register of the
//! CAN controller's data registers. For example, in order to use the IF1
//! register set on CAN controller 0, the value would be: \b CAN0_BASE \b +
//! \b CAN_O_IF1DA1.
//! \param iSize is the number of bytes to copy into the CAN controller.
//!
//! This function takes the steps necessary to copy data from a contiguous
//! buffer in memory into the non-contiguous data registers used by the CAN
//! controller. This function is rarely used outside of the CANMessageSet()
//! function.
//!
//! This function replaces the original CANWriteDataReg() API and performs the
//! same actions. A macro is provided in <tt>can.h</tt> to map the original
//! API to this API.
//!
//! \return None.
//
//*****************************************************************************
static void
CANDataRegWrite(unsigned char *pucData, unsigned long *pulRegister,
unsigned long ulSize)
{
unsigned long ulIdx, ulValue;
//
// Loop always copies 1 or 2 bytes per iteration.
//
for(ulIdx = 0; ulIdx < ulSize; )
{
//
// Write out the data 16 bits at a time since this is how the registers
// are aligned in memory.
//
ulValue = pucData[ulIdx++];
//
// Only write the second byte if needed otherwise it will be zero.
//
if(ulIdx < ulSize)
{
ulValue |= (pucData[ulIdx++] << 8);
}
CANRegWrite((unsigned long)(pulRegister++), ulValue);
}
}
//*****************************************************************************
//
//! \internal
//!
//! Copies data from a buffer to the CAN Data registers.
//!
//! \param pucData is a pointer to the location to store the data read from the
//! CAN controller's data registers.
//! \param pulRegister is an unsigned long pointer to the first register of the
//! CAN controller's data registers. For example, in order to use the IF1
//! register set on CAN controller 1, the value would be: \b CAN0_BASE \b +
//! \b CAN_O_IF1DA1.
//! \param iSize is the number of bytes to copy from the CAN controller.
//!
//! This function takes the steps necessary to copy data to a contiguous buffer
//! in memory from the non-contiguous data registers used by the CAN
//! controller. This function is rarely used outside of the CANMessageGet()
//! function.
//!
//! This function replaces the original CANReadDataReg() API and performs the
//! same actions. A macro is provided in <tt>can.h</tt> to map the original
//! API to this API.
//!
//! \return None.
//
//*****************************************************************************
static void
CANDataRegRead(unsigned char *pucData, unsigned long *pulRegister,
unsigned long ulSize)
{
unsigned long ulIdx, ulValue;
//
// Loop always copies 1 or 2 bytes per iteration.
//
for(ulIdx = 0; ulIdx < ulSize; )
{
//
// Read out the data 16 bits at a time since this is how the registers
// are aligned in memory.
//
ulValue = CANRegRead((unsigned long)(pulRegister++));
//
// Store the first byte.
//
pucData[ulIdx++] = (unsigned char)ulValue;
//
// Only read the second byte if needed.
//
if(ulIdx < ulSize)
{
pucData[ulIdx++] = (unsigned char)(ulValue >> 8);
}
}
}
//*****************************************************************************
//
//! Initializes the CAN controller after reset.
//!
//! \param ulBase is the base address of the CAN controller.
//!
//! After reset, the CAN controller is left in the disabled state. However,
//! the memory used for message objects contains undefined values and must be
//! cleared prior to enabling the CAN controller the first time. This prevents
//! unwanted transmission or reception of data before the message objects are
//! configured. This function must be called before enabling the controller
//! the first time.
//!
//! \return None.
//
//*****************************************************************************
void
CANInit(unsigned long ulBase)
{
unsigned long ulMsg;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Place CAN controller in init state, regardless of previous state. This
// will put controller in idle, and allow the message object RAM to be
// programmed.
//
CANRegWrite(ulBase + CAN_O_CTL, CAN_CTL_INIT);
//
// Wait for busy bit to clear
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Clear the message value bit in the arbitration register. This indicates
// the message is not valid and is a "safe" condition to leave the message
// object. The same arb reg is used to program all the message objects.
//
CANRegWrite(ulBase + CAN_O_IF1CMSK, CAN_IF1CMSK_WRNRD | CAN_IF1CMSK_ARB |
CAN_IF1CMSK_CONTROL);
CANRegWrite(ulBase + CAN_O_IF1ARB2, 0);
CANRegWrite(ulBase + CAN_O_IF1MCTL, 0);
//
// Loop through to program all 32 message objects
//
for(ulMsg = 1; ulMsg <= 32; ulMsg++)
{
//
// Wait for busy bit to clear
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Initiate programming the message object
//
CANRegWrite(ulBase + CAN_O_IF1CRQ, ulMsg);
}
//
// Make sure that the interrupt and new data flags are updated for the
// message objects.
//
CANRegWrite(ulBase + CAN_O_IF1CMSK, CAN_IF1CMSK_NEWDAT |
CAN_IF1CMSK_CLRINTPND);
//
// Loop through to program all 32 message objects
//
for(ulMsg = 1; ulMsg <= 32; ulMsg++)
{
//
// Wait for busy bit to clear.
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Initiate programming the message object
//
CANRegWrite(ulBase + CAN_O_IF1CRQ, ulMsg);
}
//
// Acknowledge any pending status interrupts.
//
CANRegRead(ulBase + CAN_O_STS);
}
//*****************************************************************************
//
//! Enables the CAN controller.
//!
//! \param ulBase is the base address of the CAN controller to enable.
//!
//! Enables the CAN controller for message processing. Once enabled, the
//! controller automatically transmits any pending frames, and processes any
//! received frames. The controller can be stopped by calling CANDisable().
//! Prior to calling CANEnable(), CANInit() should have been called to
//! initialize the controller and the CAN bus clock should be configured by
//! calling CANBitTimingSet().
//!
//! \return None.
//
//*****************************************************************************
void
CANEnable(unsigned long ulBase)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Clear the init bit in the control register.
//
CANRegWrite(ulBase + CAN_O_CTL,
CANRegRead(ulBase + CAN_O_CTL) & ~CAN_CTL_INIT);
}
//*****************************************************************************
//
//! Disables the CAN controller.
//!
//! \param ulBase is the base address of the CAN controller to disable.
//!
//! Disables the CAN controller for message processing. When disabled, the
//! controller no longer automatically processes data on the CAN bus. The
//! controller can be restarted by calling CANEnable(). The state of the CAN
//! controller and the message objects in the controller are left as they were
//! before this call was made.
//!
//! \return None.
//
//*****************************************************************************
void
CANDisable(unsigned long ulBase)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Set the init bit in the control register.
//
CANRegWrite(ulBase + CAN_O_CTL,
CANRegRead(ulBase + CAN_O_CTL) | CAN_CTL_INIT);
}
//*****************************************************************************
//
//! Reads the current settings for the CAN controller bit timing.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param pClkParms is a pointer to a structure to hold the timing parameters.
//!
//! This function reads the current configuration of the CAN controller bit
//! clock timing and stores the resulting information in the structure
//! supplied by the caller. Refer to CANBitTimingSet() for the meaning of the
//! values that are returned in the structure pointed to by \e pClkParms.
//!
//! This function replaces the original CANGetBitTiming() API and performs the
//! same actions. A macro is provided in <tt>can.h</tt> to map the original
//! API to this API.
//!
//! \return None.
//
//*****************************************************************************
void
CANBitTimingGet(unsigned long ulBase, tCANBitClkParms *pClkParms)
{
unsigned long ulBitReg;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT(pClkParms != 0);
//
// Read out all the bit timing values from the CAN controller registers.
//
ulBitReg = CANRegRead(ulBase + CAN_O_BIT);
//
// Set the phase 2 segment.
//
pClkParms->ulPhase2Seg =
((ulBitReg & CAN_BIT_TSEG2_M) >> CAN_BIT_TSEG2_S) + 1;
//
// Set the phase 1 segment.
//
pClkParms->ulSyncPropPhase1Seg =
((ulBitReg & CAN_BIT_TSEG1_M) >> CAN_BIT_TSEG1_S) + 1;
//
// Set the synchronous jump width.
//
pClkParms->ulSJW = ((ulBitReg & CAN_BIT_SJW_M) >> CAN_BIT_SJW_S) + 1;
//
// Set the pre-divider for the CAN bus bit clock.
//
pClkParms->ulQuantumPrescaler =
((ulBitReg & CAN_BIT_BRP_M) |
((CANRegRead(ulBase + CAN_O_BRPE) & CAN_BRPE_BRPE_M) << 6)) + 1;
}
//*****************************************************************************
//
//! Sets the CAN bit timing values to a nominal setting based on a desired
//! bit rate.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulSourceClock is the system clock for the device in Hz.
//! \param ulBitRate is the desired bit rate.
//!
//! This function sets the CAN bit timing for the bit rate passed in the
//! \e ulBitRate parameter based on the \e ulSourceClock parameter. Because the
//! CAN clock is based off of the system clock, the calling function should pass
//! in the source clock rate either by retrieving it from SysCtlClockGet() or
//! using a specific value in Hz. The CAN bit timing is calculated assuming a
//! minimal amount of propagation delay, which works for most cases where
//! the network length is short. If tighter timing requirements or longer
//! network lengths are needed, then the CANBitTimingSet() function is
//! available for full customization of all of the CAN bit timing values.
//! Because not all bit rates can be matched exactly, the bit rate is set to
//! the value closest to the desired bit rate without being higher than the
//! \e ulBitRate value.
//!
//! \note On some devices the source clock is fixed at 8MHz so the
//! \e ulSourceClock should be set to 8000000.
//!
//! \return This function returns the bit rate that the CAN controller was
//! configured to use or it returns 0 to indicate that the bit rate was not
//! changed because the requested bit rate was not valid.
//!
//*****************************************************************************
unsigned long
CANBitRateSet(unsigned long ulBase, unsigned long ulSourceClock,
unsigned long ulBitRate)
{
unsigned long ulDesiredRatio;
unsigned long ulCANBits;
unsigned long ulPreDivide;
unsigned long ulRegValue;
unsigned short usCANCTL;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT(ulSourceClock != 0);
ASSERT(ulBitRate != 0);
//
// Calculate the desired clock rate.
//
ulDesiredRatio = ulSourceClock / ulBitRate;
//
// Make sure that the ratio of CAN bit rate to processor clock is not too
// small or too large.
//
ASSERT(ulDesiredRatio <= (CAN_MAX_PRE_DIVISOR * CAN_MAX_BIT_DIVISOR));
ASSERT(ulDesiredRatio >= (CAN_MIN_PRE_DIVISOR * CAN_MIN_BIT_DIVISOR));
//
// Make sure that the Desired Ratio is not too large. This enforces the
// requirement that the bit rate is larger than requested.
//
if((ulSourceClock / ulDesiredRatio) > ulBitRate)
{
ulDesiredRatio += 1;
}
//
// Check all possible values to find a matching value.
//
while(ulDesiredRatio <= (CAN_MAX_PRE_DIVISOR * CAN_MAX_BIT_DIVISOR))
{
//
// Loop through all possible CAN bit divisors.
//
for(ulCANBits = CAN_MAX_BIT_DIVISOR; ulCANBits >= CAN_MIN_BIT_DIVISOR;
ulCANBits--)
{
//
// For a given CAN bit divisor save the pre divisor.
//
ulPreDivide = ulDesiredRatio / ulCANBits;
//
// If the calculated divisors match the desired clock ratio then
// return these bit rate and set the CAN bit timing.
//
if((ulPreDivide * ulCANBits) == ulDesiredRatio)
{
//
// Start building the bit timing value by adding the bit timing
// in time quanta.
//
ulRegValue = g_usCANBitValues[ulCANBits - CAN_MIN_BIT_DIVISOR];
//
// To set the bit timing register, the controller must be placed
// in init mode (if not already), and also configuration change
// bit enabled. The state of the register should be saved
// so it can be restored.
//
usCANCTL = CANRegRead(ulBase + CAN_O_CTL);
CANRegWrite(ulBase + CAN_O_CTL,
usCANCTL | CAN_CTL_INIT | CAN_CTL_CCE);
//
// Now add in the pre-scalar on the bit rate.
//
ulRegValue |= ((ulPreDivide - 1) & CAN_BIT_BRP_M);
//
// Set the clock bits in the and the lower bits of the
// pre-scalar.
//
CANRegWrite(ulBase + CAN_O_BIT, ulRegValue);
//
// Set the divider upper bits in the extension register.
//
CANRegWrite(ulBase + CAN_O_BRPE,
((ulPreDivide - 1) >> 6) & CAN_BRPE_BRPE_M);
//
// Restore the saved CAN Control register.
//
CANRegWrite(ulBase + CAN_O_CTL, usCANCTL);
//
// Return the computed bit rate.
//
return(ulSourceClock / ( ulPreDivide * ulCANBits));
}
}
//
// Move the divisor up one and look again. Only in rare cases are
// more than 2 loops required to find the value.
//
ulDesiredRatio++;
}
//
// A valid combination could not be found, so return 0 to indicate that the
// bit rate was not changed.
//
return(0);
}
//*****************************************************************************
//
//! Configures the CAN controller bit timing.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param pClkParms points to the structure with the clock parameters.
//!
//! Configures the various timing parameters for the CAN bus bit timing:
//! Propagation segment, Phase Buffer 1 segment, Phase Buffer 2 segment, and
//! the Synchronization Jump Width. The values for Propagation and Phase
//! Buffer 1 segments are derived from the combination
//! \e pClkParms->ulSyncPropPhase1Seg parameter. Phase Buffer 2 is determined
//! from the \e pClkParms->ulPhase2Seg parameter. These two parameters, along
//! with \e pClkParms->ulSJW are based in units of bit time quanta. The actual
//! quantum time is determined by the \e pClkParms->ulQuantumPrescaler value,
//! which specifies the divisor for the CAN module clock.
//!
//! The total bit time, in quanta, is the sum of the two Seg parameters,
//! as follows:
//!
//! bit_time_q = ulSyncPropPhase1Seg + ulPhase2Seg + 1
//!
//! Note that the Sync_Seg is always one quantum in duration, and is added
//! to derive the correct duration of Prop_Seg and Phase1_Seg.
//!
//! The equation to determine the actual bit rate is as follows:
//!
//! CAN Clock /
//! ((\e ulSyncPropPhase1Seg + \e ulPhase2Seg + 1) * (\e ulQuantumPrescaler))
//!
//! Thus with \e ulSyncPropPhase1Seg = 4, \e ulPhase2Seg = 1,
//! \e ulQuantumPrescaler = 2 and an 8 MHz CAN clock, the bit rate is
//! (8 MHz) / ((5 + 2 + 1) * 2) or 500 Kbit/sec.
//!
//! This function replaces the original CANSetBitTiming() API and performs the
//! same actions. A macro is provided in <tt>can.h</tt> to map the original
//! API to this API.
//!
//! \return None.
//
//*****************************************************************************
void
CANBitTimingSet(unsigned long ulBase, tCANBitClkParms *pClkParms)
{
unsigned long ulBitReg, ulSavedInit;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT(pClkParms != 0);
//
// The phase 1 segment must be in the range from 2 to 16.
//
ASSERT((pClkParms->ulSyncPropPhase1Seg >= 2) &&
(pClkParms->ulSyncPropPhase1Seg <= 16));
//
// The phase 2 segment must be in the range from 1 to 8.
//
ASSERT((pClkParms->ulPhase2Seg >= 1) && (pClkParms->ulPhase2Seg <= 8));
//
// The synchronous jump windows must be in the range from 1 to 4.
//
ASSERT((pClkParms->ulSJW >= 1) && (pClkParms->ulSJW <= 4));
//
// The CAN clock pre-divider must be in the range from 1 to 1024.
//
ASSERT((pClkParms->ulQuantumPrescaler <= 1024) &&
(pClkParms->ulQuantumPrescaler >= 1));
//
// To set the bit timing register, the controller must be placed in init
// mode (if not already), and also configuration change bit enabled. State
// of the init bit should be saved so it can be restored at the end.
//
ulSavedInit = CANRegRead(ulBase + CAN_O_CTL);
CANRegWrite(ulBase + CAN_O_CTL, ulSavedInit | CAN_CTL_INIT | CAN_CTL_CCE);
//
// Set the bit fields of the bit timing register according to the parms.
//
ulBitReg = (((pClkParms->ulPhase2Seg - 1) << CAN_BIT_TSEG2_S) &
CAN_BIT_TSEG2_M);
ulBitReg |= (((pClkParms->ulSyncPropPhase1Seg - 1) << CAN_BIT_TSEG1_S) &
CAN_BIT_TSEG1_M);
ulBitReg |= ((pClkParms->ulSJW - 1) << CAN_BIT_SJW_S) & CAN_BIT_SJW_M;
ulBitReg |= (pClkParms->ulQuantumPrescaler - 1) & CAN_BIT_BRP_M;
CANRegWrite(ulBase + CAN_O_BIT, ulBitReg);
//
// Set the divider upper bits in the extension register.
//
CANRegWrite(ulBase + CAN_O_BRPE,
((pClkParms->ulQuantumPrescaler - 1) >> 6) & CAN_BRPE_BRPE_M);
//
// Clear the config change bit, and restore the init bit.
//
ulSavedInit &= ~CAN_CTL_CCE;
//
// If Init was not set before, then clear it.
//
if(ulSavedInit & CAN_CTL_INIT)
{
ulSavedInit &= ~CAN_CTL_INIT;
}
CANRegWrite(ulBase + CAN_O_CTL, ulSavedInit);
}
//*****************************************************************************
//
//! Registers an interrupt handler for the CAN controller.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param pfnHandler is a pointer to the function to be called when the
//! enabled CAN interrupts occur.
//!
//! This function registers the interrupt handler in the interrupt vector
//! table, and enables CAN interrupts on the interrupt controller; specific CAN
//! interrupt sources must be enabled using CANIntEnable(). The interrupt
//! handler being registered must clear the source of the interrupt using
//! CANIntClear().
//!
//! If the application is using a static interrupt vector table stored in
//! flash, then it is not necessary to register the interrupt handler this way.
//! Instead, IntEnable() should be used to enable CAN interrupts on the
//! interrupt controller.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
CANIntRegister(unsigned long ulBase, void (*pfnHandler)(void))
{
unsigned long ulIntNumber;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Get the actual interrupt number for this CAN controller.
//
ulIntNumber = CANIntNumberGet(ulBase);
//
// Register the interrupt handler.
//
IntRegister(ulIntNumber, pfnHandler);
//
// Enable the Ethernet interrupt.
//
IntEnable(ulIntNumber);
}
//*****************************************************************************
//
//! Unregisters an interrupt handler for the CAN controller.
//!
//! \param ulBase is the base address of the controller.
//!
//! This function unregisters the previously registered interrupt handler and
//! disables the interrupt in the interrupt controller.
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
CANIntUnregister(unsigned long ulBase)
{
unsigned long ulIntNumber;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Get the actual interrupt number for this CAN controller.
//
ulIntNumber = CANIntNumberGet(ulBase);
//
// Disable the CAN interrupt.
//
IntDisable(ulIntNumber);
//
// Register the interrupt handler.
//
IntUnregister(ulIntNumber);
}
//*****************************************************************************
//
//! Enables individual CAN controller interrupt sources.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulIntFlags is the bit mask of the interrupt sources to be enabled.
//!
//! This function enables specific interrupt sources of the CAN controller.
//! Only enabled sources cause a processor interrupt.
//!
//! The \e ulIntFlags parameter is the logical OR of any of the following:
//!
//! - \b CAN_INT_ERROR - a controller error condition has occurred
//! - \b CAN_INT_STATUS - a message transfer has completed, or a bus error has
//! been detected
//! - \b CAN_INT_MASTER - allow CAN controller to generate interrupts
//!
//! In order to generate any interrupts, \b CAN_INT_MASTER must be enabled.
//! Further, for any particular transaction from a message object to generate
//! an interrupt, that message object must have interrupts enabled (see
//! CANMessageSet()). \b CAN_INT_ERROR will generate an interrupt if the
//! controller enters the ``bus off'' condition, or if the error counters reach
//! a limit. \b CAN_INT_STATUS generates an interrupt under quite a few
//! status conditions and may provide more interrupts than the application
//! needs to handle. When an interrupt occurs, use CANIntStatus() to determine
//! the cause.
//!
//! \return None.
//
//*****************************************************************************
void
CANIntEnable(unsigned long ulBase, unsigned long ulIntFlags)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT((ulIntFlags & ~(CAN_CTL_EIE | CAN_CTL_SIE | CAN_CTL_IE)) == 0);
//
// Enable the specified interrupts.
//
CANRegWrite(ulBase + CAN_O_CTL,
CANRegRead(ulBase + CAN_O_CTL) | ulIntFlags);
}
//*****************************************************************************
//
//! Disables individual CAN controller interrupt sources.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulIntFlags is the bit mask of the interrupt sources to be disabled.
//!
//! Disables the specified CAN controller interrupt sources. Only enabled
//! interrupt sources can cause a processor interrupt.
//!
//! The \e ulIntFlags parameter has the same definition as in the
//! CANIntEnable() function.
//!
//! \return None.
//
//*****************************************************************************
void
CANIntDisable(unsigned long ulBase, unsigned long ulIntFlags)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT((ulIntFlags & ~(CAN_CTL_EIE | CAN_CTL_SIE | CAN_CTL_IE)) == 0);
//
// Disable the specified interrupts.
//
CANRegWrite(ulBase + CAN_O_CTL,
CANRegRead(ulBase + CAN_O_CTL) & ~(ulIntFlags));
}
//*****************************************************************************
//
//! Returns the current CAN controller interrupt status.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param eIntStsReg indicates which interrupt status register to read
//!
//! This function returns the value of one of two interrupt status registers.
//! The interrupt status register read is determined by the \e eIntStsReg
//! parameter, which can have one of the following values:
//!
//! - \b CAN_INT_STS_CAUSE - indicates the cause of the interrupt
//! - \b CAN_INT_STS_OBJECT - indicates pending interrupts of all message
//! objects
//!
//! \b CAN_INT_STS_CAUSE returns the value of the controller interrupt register
//! and indicates the cause of the interrupt. The value returned is
//! \b CAN_INT_INTID_STATUS if the cause is a status interrupt. In this case,
//! the status register should be read with the CANStatusGet() function.
//! Calling this function to read the status also clears the status
//! interrupt. If the value of the interrupt register is in the range 1-32,
//! then this indicates the number of the highest priority message object that
//! has an interrupt pending. The message object interrupt can be cleared by
//! using the CANIntClear() function, or by reading the message using
//! CANMessageGet() in the case of a received message. The interrupt handler
//! can read the interrupt status again to make sure all pending interrupts are
//! cleared before returning from the interrupt.
//!
//! \b CAN_INT_STS_OBJECT returns a bit mask indicating which message objects
//! have pending interrupts. This value can be used to discover all of the
//! pending interrupts at once, as opposed to repeatedly reading the interrupt
//! register by using \b CAN_INT_STS_CAUSE.
//!
//! \return Returns the value of one of the interrupt status registers.
//
//*****************************************************************************
unsigned long
CANIntStatus(unsigned long ulBase, tCANIntStsReg eIntStsReg)
{
unsigned long ulStatus;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// See which status the caller is looking for.
//
switch(eIntStsReg)
{
//
// The caller wants the global interrupt status for the CAN controller
// specified by ulBase.
//
case CAN_INT_STS_CAUSE:
{
ulStatus = CANRegRead(ulBase + CAN_O_INT);
break;
}
//
// The caller wants the current message status interrupt for all
// messages.
//
case CAN_INT_STS_OBJECT:
{
//
// Read and combine both 16 bit values into one 32bit status.
//
ulStatus = (CANRegRead(ulBase + CAN_O_MSG1INT) &
CAN_MSG1INT_INTPND_M);
ulStatus |= (CANRegRead(ulBase + CAN_O_MSG2INT) << 16);
break;
}
//
// Request was for unknown status so just return 0.
//
default:
{
ulStatus = 0;
break;
}
}
//
// Return the interrupt status value
//
return(ulStatus);
}
//*****************************************************************************
//
//! Clears a CAN interrupt source.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulIntClr is a value indicating which interrupt source to clear.
//!
//! This function can be used to clear a specific interrupt source. The
//! \e ulIntClr parameter should be one of the following values:
//!
//! - \b CAN_INT_INTID_STATUS - Clears a status interrupt.
//! - 1-32 - Clears the specified message object interrupt
//!
//! It is not necessary to use this function to clear an interrupt. This
//! function should only be used if the application wants to clear an interrupt
//! source without taking the normal interrupt action.
//!
//! Normally, the status interrupt is cleared by reading the controller status
//! using CANStatusGet(). A specific message object interrupt is normally
//! cleared by reading the message object using CANMessageGet().
//!
//! \note Because there is a write buffer in the Cortex-M processor, it may
//! take several clock cycles before the interrupt source is actually cleared.
//! Therefore, it is recommended that the interrupt source be cleared early in
//! the interrupt handler (as opposed to the very last action) to avoid
//! returning from the interrupt handler before the interrupt source is
//! actually cleared. Failure to do so may result in the interrupt handler
//! being immediately reentered (because the interrupt controller still sees
//! the interrupt source asserted).
//!
//! \return None.
//
//*****************************************************************************
void
CANIntClear(unsigned long ulBase, unsigned long ulIntClr)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT((ulIntClr == CAN_INT_INTID_STATUS) ||
((ulIntClr>=1) && (ulIntClr <=32)));
if(ulIntClr == CAN_INT_INTID_STATUS)
{
//
// Simply read and discard the status to clear the interrupt.
//
CANRegRead(ulBase + CAN_O_STS);
}
else
{
//
// Wait to be sure that this interface is not busy.
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Only change the interrupt pending state by setting only the
// CAN_IF1CMSK_CLRINTPND bit.
//
CANRegWrite(ulBase + CAN_O_IF1CMSK, CAN_IF1CMSK_CLRINTPND);
//
// Send the clear pending interrupt command to the CAN controller.
//
CANRegWrite(ulBase + CAN_O_IF1CRQ, ulIntClr & CAN_IF1CRQ_MNUM_M);
//
// Wait to be sure that this interface is not busy.
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
}
}
//*****************************************************************************
//
//! Sets the CAN controller automatic retransmission behavior.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param bAutoRetry enables automatic retransmission.
//!
//! This function enables or disables automatic retransmission of messages with
//! detected errors. If \e bAutoRetry is \b true, then automatic retransmission
//! is enabled, otherwise it is disabled.
//!
//! \return None.
//
//*****************************************************************************
void
CANRetrySet(unsigned long ulBase, tBoolean bAutoRetry)
{
unsigned long ulCtlReg;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ulCtlReg = CANRegRead(ulBase + CAN_O_CTL);
//
// Conditionally set the DAR bit to enable/disable auto-retry.
//
if(bAutoRetry)
{
//
// Clearing the DAR bit tells the controller to not disable the
// auto-retry of messages which were not transmitted or received
// correctly.
//
ulCtlReg &= ~CAN_CTL_DAR;
}
else
{
//
// Setting the DAR bit tells the controller to disable the auto-retry
// of messages which were not transmitted or received correctly.
//
ulCtlReg |= CAN_CTL_DAR;
}
CANRegWrite(ulBase + CAN_O_CTL, ulCtlReg);
}
//*****************************************************************************
//
//! Returns the current setting for automatic retransmission.
//!
//! \param ulBase is the base address of the CAN controller.
//!
//! This function reads the current setting for automatic retransmission in the CAN
//! controller and returns it to the caller.
//!
//! \return Returns \b true if automatic retransmission is enabled, \b false
//! otherwise.
//
//*****************************************************************************
tBoolean
CANRetryGet(unsigned long ulBase)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Read the disable automatic retry setting from the CAN controller.
//
if(CANRegRead(ulBase + CAN_O_CTL) & CAN_CTL_DAR)
{
//
// Automatic data retransmission is not enabled.
//
return(false);
}
//
// Automatic data retransmission is enabled.
//
return(true);
}
//*****************************************************************************
//
//! Reads one of the controller status registers.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param eStatusReg is the status register to read.
//!
//! This function reads a status register of the CAN controller and returns it
//! to the caller.
//! The different status registers are:
//!
//! - \b CAN_STS_CONTROL - the main controller status
//! - \b CAN_STS_TXREQUEST - bit mask of objects pending transmission
//! - \b CAN_STS_NEWDAT - bit mask of objects with new data
//! - \b CAN_STS_MSGVAL - bit mask of objects with valid configuration
//!
//! When reading the main controller status register, a pending status
//! interrupt is cleared. This parameter should be used in the interrupt
//! handler for the CAN controller if the cause is a status interrupt. The
//! controller status register fields are as follows:
//!
//! - \b CAN_STATUS_BUS_OFF - controller is in bus-off condition
//! - \b CAN_STATUS_EWARN - an error counter has reached a limit of at least 96
//! - \b CAN_STATUS_EPASS - CAN controller is in the error passive state
//! - \b CAN_STATUS_RXOK - a message was received successfully (independent of
//! any message filtering).
//! - \b CAN_STATUS_TXOK - a message was successfully transmitted
//! - \b CAN_STATUS_LEC_MSK - mask of last error code bits (3 bits)
//! - \b CAN_STATUS_LEC_NONE - no error
//! - \b CAN_STATUS_LEC_STUFF - stuffing error detected
//! - \b CAN_STATUS_LEC_FORM - a format error occurred in the fixed format part
//! of a message
//! - \b CAN_STATUS_LEC_ACK - a transmitted message was not acknowledged
//! - \b CAN_STATUS_LEC_BIT1 - dominant level detected when trying to send in
//! recessive mode
//! - \b CAN_STATUS_LEC_BIT0 - recessive level detected when trying to send in
//! dominant mode
//! - \b CAN_STATUS_LEC_CRC - CRC error in received message
//!
//! The remaining status registers consist of 32-bit-wide bit maps to the
//! message objects. They can be used to quickly obtain information about the
//! status of all the message objects without needing to query each one. They
//! contain the following information:
//!
//! - \b CAN_STS_TXREQUEST - if a message object's TXRQST bit is set, a
//! transmission is pending on that object. The application can use this
//! information to determine which objects are still waiting to send a
//! message.
//! - \b CAN_STS_NEWDAT - if a message object's NEWDAT bit is set, a new
//! message has been received in that object, and has not yet been picked up
//! by the host application
//! - \b CAN_STS_MSGVAL - if a message object's MSGVAL bit is set, the object
//! has a valid configuration programmed. The host application can use this
//! information to determine which message objects are empty/unused.
//!
//! \return Returns the value of the status register.
//
//*****************************************************************************
unsigned long
CANStatusGet(unsigned long ulBase, tCANStsReg eStatusReg)
{
unsigned long ulStatus;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
switch(eStatusReg)
{
//
// Just return the global CAN status register since that is what was
// requested.
//
case CAN_STS_CONTROL:
{
ulStatus = CANRegRead(ulBase + CAN_O_STS);
CANRegWrite(ulBase + CAN_O_STS,
~(CAN_STS_RXOK | CAN_STS_TXOK | CAN_STS_LEC_M));
break;
}
//
// Combine the Transmit status bits into one 32bit value.
//
case CAN_STS_TXREQUEST:
{
ulStatus = CANRegRead(ulBase + CAN_O_TXRQ1);
ulStatus |= CANRegRead(ulBase + CAN_O_TXRQ2) << 16;
break;
}
//
// Combine the New Data status bits into one 32bit value.
//
case CAN_STS_NEWDAT:
{
ulStatus = CANRegRead(ulBase + CAN_O_NWDA1);
ulStatus |= CANRegRead(ulBase + CAN_O_NWDA2) << 16;
break;
}
//
// Combine the Message valid status bits into one 32bit value.
//
case CAN_STS_MSGVAL:
{
ulStatus = CANRegRead(ulBase + CAN_O_MSG1VAL);
ulStatus |= CANRegRead(ulBase + CAN_O_MSG2VAL) << 16;
break;
}
//
// Unknown CAN status requested so return 0.
//
default:
{
ulStatus = 0;
break;
}
}
return(ulStatus);
}
//*****************************************************************************
//
//! Reads the CAN controller error counter register.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param pulRxCount is a pointer to storage for the receive error counter.
//! \param pulTxCount is a pointer to storage for the transmit error counter.
//!
//! This function reads the error counter register and returns the transmit and
//! receive error counts to the caller along with a flag indicating if the
//! controller receive counter has reached the error passive limit. The values
//! of the receive and transmit error counters are returned through the pointers
//! provided as parameters.
//!
//! After this call, \e *pulRxCount holds the current receive error count
//! and \e *pulTxCount holds the current transmit error count.
//!
//! \return Returns \b true if the receive error count has reached the error
//! passive limit, and \b false if the error count is below the error passive
//! limit.
//
//*****************************************************************************
tBoolean
CANErrCntrGet(unsigned long ulBase, unsigned long *pulRxCount,
unsigned long *pulTxCount)
{
unsigned long ulCANError;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
//
// Read the current count of transmit/receive errors.
//
ulCANError = CANRegRead(ulBase + CAN_O_ERR);
//
// Extract the error numbers from the register value.
//
*pulRxCount = (ulCANError & CAN_ERR_REC_M) >> CAN_ERR_REC_S;
*pulTxCount = (ulCANError & CAN_ERR_TEC_M) >> CAN_ERR_TEC_S;
if(ulCANError & CAN_ERR_RP)
{
return(true);
}
return(false);
}
//*****************************************************************************
//
//! Configures a message object in the CAN controller.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulObjID is the object number to configure (1-32).
//! \param pMsgObject is a pointer to a structure containing message object
//! settings.
//! \param eMsgType indicates the type of message for this object.
//!
//! This function is used to configure any one of the 32 message objects in the
//! CAN controller. A message object can be configured to be any type of CAN
//! message object as well as to use automatic transmission and reception.
//! This call also allows the message object to be configured to generate
//! interrupts on completion of message receipt or transmission. The
//! message object can also be configured with a filter/mask so that actions
//! are only taken when a message that meets certain parameters is seen on the
//! CAN bus.
//!
//! The \e eMsgType parameter must be one of the following values:
//!
//! - \b MSG_OBJ_TYPE_TX - CAN transmit message object.
//! - \b MSG_OBJ_TYPE_TX_REMOTE - CAN transmit remote request message object.
//! - \b MSG_OBJ_TYPE_RX - CAN receive message object.
//! - \b MSG_OBJ_TYPE_RX_REMOTE - CAN receive remote request message object.
//! - \b MSG_OBJ_TYPE_RXTX_REMOTE - CAN remote frame receive remote, then
//! transmit message object.
//!
//! The message object pointed to by \e pMsgObject must be populated by the
//! caller, as follows:
//!
//! - \e ulMsgID - contains the message ID, either 11 or 29 bits.
//! - \e ulMsgIDMask - mask of bits from \e ulMsgID that must match if
//! identifier filtering is enabled.
//! - \e ulFlags
//! - Set \b MSG_OBJ_TX_INT_ENABLE flag to enable interrupt on transmission.
//! - Set \b MSG_OBJ_RX_INT_ENABLE flag to enable interrupt on receipt.
//! - Set \b MSG_OBJ_USE_ID_FILTER flag to enable filtering based on the
//! identifier mask specified by \e ulMsgIDMask.
//! - \e ulMsgLen - the number of bytes in the message data. This parameter
//! should be non-zero even for a remote frame; it should match the expected
//! bytes of data in the responding data frame.
//! - \e pucMsgData - points to a buffer containing up to 8 bytes of data for a
//! data frame.
//!
//! \b Example: To send a data frame or remote frame (in response to a remote
//! request), take the following steps:
//!
//! -# Set \e eMsgType to \b MSG_OBJ_TYPE_TX.
//! -# Set \e pMsgObject->ulMsgID to the message ID.
//! -# Set \e pMsgObject->ulFlags. Make sure to set \b MSG_OBJ_TX_INT_ENABLE to
//! allow an interrupt to be generated when the message is sent.
//! -# Set \e pMsgObject->ulMsgLen to the number of bytes in the data frame.
//! -# Set \e pMsgObject->pucMsgData to point to an array containing the bytes
//! to send in the message.
//! -# Call this function with \e ulObjID set to one of the 32 object buffers.
//!
//! \b Example: To receive a specific data frame, take the following steps:
//!
//! -# Set \e eMsgObjType to \b MSG_OBJ_TYPE_RX.
//! -# Set \e pMsgObject->ulMsgID to the full message ID, or a partial mask to
//! use partial ID matching.
//! -# Set \e pMsgObject->ulMsgIDMask bits that should be used for masking
//! during comparison.
//! -# Set \e pMsgObject->ulFlags as follows:
//! - Set \b MSG_OBJ_RX_INT_ENABLE flag to be interrupted when the data frame
//! is received.
//! - Set \b MSG_OBJ_USE_ID_FILTER flag to enable identifier-based filtering.
//! -# Set \e pMsgObject->ulMsgLen to the number of bytes in the expected data
//! frame.
//! -# The buffer pointed to by \e pMsgObject->pucMsgData is not used by this
//! call as no data is present at the time of the call.
//! -# Call this function with \e ulObjID set to one of the 32 object buffers.
//!
//! If you specify a message object buffer that already contains a message
//! definition, it is overwritten.
//!
//! \return None.
//
//*****************************************************************************
void
CANMessageSet(unsigned long ulBase, unsigned long ulObjID,
tCANMsgObject *pMsgObject, tMsgObjType eMsgType)
{
unsigned short usCmdMaskReg;
unsigned short usMaskReg0, usMaskReg1;
unsigned short usArbReg0, usArbReg1;
unsigned short usMsgCtrl;
tBoolean bTransferData;
tBoolean bUseExtendedID;
bTransferData = 0;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT((ulObjID <= 32) && (ulObjID != 0));
ASSERT((eMsgType == MSG_OBJ_TYPE_TX) ||
(eMsgType == MSG_OBJ_TYPE_TX_REMOTE) ||
(eMsgType == MSG_OBJ_TYPE_RX) ||
(eMsgType == MSG_OBJ_TYPE_RX_REMOTE) ||
(eMsgType == MSG_OBJ_TYPE_TX_REMOTE) ||
(eMsgType == MSG_OBJ_TYPE_RXTX_REMOTE));
//
// Wait for busy bit to clear
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// See if we need to use an extended identifier or not.
//
if((pMsgObject->ulMsgID > CAN_MAX_11BIT_MSG_ID) ||
(pMsgObject->ulFlags & MSG_OBJ_EXTENDED_ID))
{
bUseExtendedID = 1;
}
else
{
bUseExtendedID = 0;
}
//
// This is always a write to the Message object as this call is setting a
// message object. This call will also always set all size bits so it sets
// both data bits. The call will use the CONTROL register to set control
// bits so this bit needs to be set as well.
//
usCmdMaskReg = (CAN_IF1CMSK_WRNRD | CAN_IF1CMSK_DATAA | CAN_IF1CMSK_DATAB |
CAN_IF1CMSK_CONTROL);
//
// Initialize the values to a known state before filling them in based on
// the type of message object that is being configured.
//
usArbReg0 = 0;
usArbReg1 = 0;
usMsgCtrl = 0;
usMaskReg0 = 0;
usMaskReg1 = 0;
switch(eMsgType)
{
//
// Transmit message object.
//
case MSG_OBJ_TYPE_TX:
{
//
// Set the TXRQST bit and the reset the rest of the register.
//
usMsgCtrl |= CAN_IF1MCTL_TXRQST;
usArbReg1 = CAN_IF1ARB2_DIR;
bTransferData = 1;
break;
}
//
// Transmit remote request message object
//
case MSG_OBJ_TYPE_TX_REMOTE:
{
//
// Set the TXRQST bit and the reset the rest of the register.
//
usMsgCtrl |= CAN_IF1MCTL_TXRQST;
usArbReg1 = 0;
break;
}
//
// Receive message object.
//
case MSG_OBJ_TYPE_RX:
{
//
// This clears the DIR bit along with everything else. The TXRQST
// bit was cleared by defaulting usMsgCtrl to 0.
//
usArbReg1 = 0;
break;
}
//
// Receive remote request message object.
//
case MSG_OBJ_TYPE_RX_REMOTE:
{
//
// The DIR bit is set to one for remote receivers. The TXRQST bit
// was cleared by defaulting usMsgCtrl to 0.
//
usArbReg1 = CAN_IF1ARB2_DIR;
//
// Set this object so that it only indicates that a remote frame
// was received and allow for software to handle it by sending back
// a data frame.
//
usMsgCtrl = CAN_IF1MCTL_UMASK;
//
// Use the full Identifier by default.
//
usMaskReg0 = 0xffff;
usMaskReg1 = 0x1fff;
//
// Make sure to send the mask to the message object.
//
usCmdMaskReg |= CAN_IF1CMSK_MASK;
break;
}
//
// Remote frame receive remote, with auto-transmit message object.
//
case MSG_OBJ_TYPE_RXTX_REMOTE:
{
//
// Oddly the DIR bit is set to one for remote receivers.
//
usArbReg1 = CAN_IF1ARB2_DIR;
//
// Set this object to auto answer if a matching identifier is seen.
//
usMsgCtrl = CAN_IF1MCTL_RMTEN | CAN_IF1MCTL_UMASK;
//
// The data to be returned needs to be filled in.
//
bTransferData = 1;
break;
}
//
// This case should never happen due to the ASSERT statement at the
// beginning of this function.
//
default:
{
return;
}
}
//
// Configure the Mask Registers.
//
if(pMsgObject->ulFlags & MSG_OBJ_USE_ID_FILTER)
{
if(bUseExtendedID)
{
//
// Set the 29 bits of Identifier mask that were requested.
//
usMaskReg0 = pMsgObject->ulMsgIDMask & CAN_IF1MSK1_IDMSK_M;
usMaskReg1 = ((pMsgObject->ulMsgIDMask >> 16) &
CAN_IF1MSK2_IDMSK_M);
}
else
{
//
// Lower 16 bit are unused so set them to zero.
//
usMaskReg0 = 0;
//
// Put the 11 bit Mask Identifier into the upper bits of the field
// in the register.
//
usMaskReg1 = ((pMsgObject->ulMsgIDMask << 2) &
CAN_IF1MSK2_IDMSK_M);
}
}
//
// If the caller wants to filter on the extended ID bit then set it.
//
if((pMsgObject->ulFlags & MSG_OBJ_USE_EXT_FILTER) ==
MSG_OBJ_USE_EXT_FILTER)
{
usMaskReg1 |= CAN_IF1MSK2_MXTD;
}
//
// The caller wants to filter on the message direction field.
//
if((pMsgObject->ulFlags & MSG_OBJ_USE_DIR_FILTER) ==
MSG_OBJ_USE_DIR_FILTER)
{
usMaskReg1 |= CAN_IF1MSK2_MDIR;
}
if(pMsgObject->ulFlags & (MSG_OBJ_USE_ID_FILTER | MSG_OBJ_USE_DIR_FILTER |
MSG_OBJ_USE_EXT_FILTER))
{
//
// Set the UMASK bit to enable using the mask register.
//
usMsgCtrl |= CAN_IF1MCTL_UMASK;
//
// Set the MASK bit so that this gets transferred to the Message Object.
//
usCmdMaskReg |= CAN_IF1CMSK_MASK;
}
//
// Set the Arb bit so that this gets transferred to the Message object.
//
usCmdMaskReg |= CAN_IF1CMSK_ARB;
//
// Configure the Arbitration registers.
//
if(bUseExtendedID)
{
//
// Set the 29 bit version of the Identifier for this message object.
//
usArbReg0 |= pMsgObject->ulMsgID & CAN_IF1ARB1_ID_M;
usArbReg1 |= (pMsgObject->ulMsgID >> 16) & CAN_IF1ARB2_ID_M;
//
// Mark the message as valid and set the extended ID bit.
//
usArbReg1 |= CAN_IF1ARB2_MSGVAL | CAN_IF1ARB2_XTD;
}
else
{
//
// Set the 11 bit version of the Identifier for this message object.
// The lower 18 bits are set to zero.
//
usArbReg1 |= (pMsgObject->ulMsgID << 2) & CAN_IF1ARB2_ID_M;
//
// Mark the message as valid.
//
usArbReg1 |= CAN_IF1ARB2_MSGVAL;
}
//
// Set the data length since this is set for all transfers. This is also a
// single transfer and not a FIFO transfer so set EOB bit.
//
usMsgCtrl |= (pMsgObject->ulMsgLen & CAN_IF1MCTL_DLC_M);
//
// Mark this as the last entry if this is not the last entry in a FIFO.
//
if((pMsgObject->ulFlags & MSG_OBJ_FIFO) == 0)
{
usMsgCtrl |= CAN_IF1MCTL_EOB;
}
//
// Enable transmit interrupts if they should be enabled.
//
if(pMsgObject->ulFlags & MSG_OBJ_TX_INT_ENABLE)
{
usMsgCtrl |= CAN_IF1MCTL_TXIE;
}
//
// Enable receive interrupts if they should be enabled.
//
if(pMsgObject->ulFlags & MSG_OBJ_RX_INT_ENABLE)
{
usMsgCtrl |= CAN_IF1MCTL_RXIE;
}
//
// Write the data out to the CAN Data registers if needed.
//
if(bTransferData)
{
CANDataRegWrite(pMsgObject->pucMsgData,
(unsigned long *)(ulBase + CAN_O_IF1DA1),
pMsgObject->ulMsgLen);
}
//
// Write out the registers to program the message object.
//
CANRegWrite(ulBase + CAN_O_IF1CMSK, usCmdMaskReg);
CANRegWrite(ulBase + CAN_O_IF1MSK1, usMaskReg0);
CANRegWrite(ulBase + CAN_O_IF1MSK2, usMaskReg1);
CANRegWrite(ulBase + CAN_O_IF1ARB1, usArbReg0);
CANRegWrite(ulBase + CAN_O_IF1ARB2, usArbReg1);
CANRegWrite(ulBase + CAN_O_IF1MCTL, usMsgCtrl);
//
// Transfer the message object to the message object specified by ulObjID.
//
CANRegWrite(ulBase + CAN_O_IF1CRQ, ulObjID & CAN_IF1CRQ_MNUM_M);
}
//*****************************************************************************
//
//! Reads a CAN message from one of the message object buffers.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulObjID is the object number to read (1-32).
//! \param pMsgObject points to a structure containing message object fields.
//! \param bClrPendingInt indicates whether an associated interrupt should be
//! cleared.
//!
//! This function is used to read the contents of one of the 32 message objects
//! in the CAN controller and return it to the caller. The data returned is
//! stored in the fields of the caller-supplied structure pointed to by
//! \e pMsgObject. The data consists of all of the parts of a CAN message,
//! plus some control and status information.
//!
//! Normally, this function is used to read a message object that has received
//! and stored a CAN message with a certain identifier. However, this function
//! could also be used to read the contents of a message object in order to
//! load the fields of the structure in case only part of the structure must
//! be changed from a previous setting.
//!
//! When using CANMessageGet(), all of the same fields of the structure are
//! populated in the same way as when the CANMessageSet() function is used,
//! with the following exceptions:
//!
//! \e pMsgObject->ulFlags:
//!
//! - \b MSG_OBJ_NEW_DATA indicates if this data is new since the last time it
//! was read
//! - \b MSG_OBJ_DATA_LOST indicates that at least one message was received on
//! this message object and not read by the host before being overwritten.
//!
//! \return None.
//
//*****************************************************************************
void
CANMessageGet(unsigned long ulBase, unsigned long ulObjID,
tCANMsgObject *pMsgObject, tBoolean bClrPendingInt)
{
unsigned short usCmdMaskReg;
unsigned short usMaskReg0, usMaskReg1;
unsigned short usArbReg0, usArbReg1;
unsigned short usMsgCtrl;
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT((ulObjID <= 32) && (ulObjID != 0));
//
// This is always a read to the Message object as this call is setting a
// message object.
//
usCmdMaskReg = (CAN_IF1CMSK_DATAA | CAN_IF1CMSK_DATAB |
CAN_IF1CMSK_CONTROL | CAN_IF1CMSK_MASK | CAN_IF1CMSK_ARB);
//
// Clear a pending interrupt and new data in a message object.
//
if(bClrPendingInt)
{
usCmdMaskReg |= CAN_IF1CMSK_CLRINTPND;
}
//
// Set up the request for data from the message object.
//
CANRegWrite(ulBase + CAN_O_IF2CMSK, usCmdMaskReg);
//
// Transfer the message object to the message object specified by ulObjID.
//
CANRegWrite(ulBase + CAN_O_IF2CRQ, ulObjID & CAN_IF1CRQ_MNUM_M);
//
// Wait for busy bit to clear
//
while(CANRegRead(ulBase + CAN_O_IF2CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Read out the IF Registers.
//
usMaskReg0 = CANRegRead(ulBase + CAN_O_IF2MSK1);
usMaskReg1 = CANRegRead(ulBase + CAN_O_IF2MSK2);
usArbReg0 = CANRegRead(ulBase + CAN_O_IF2ARB1);
usArbReg1 = CANRegRead(ulBase + CAN_O_IF2ARB2);
usMsgCtrl = CANRegRead(ulBase + CAN_O_IF2MCTL);
pMsgObject->ulFlags = MSG_OBJ_NO_FLAGS;
//
// Determine if this is a remote frame by checking the TXRQST and DIR bits.
//
if((!(usMsgCtrl & CAN_IF1MCTL_TXRQST) && (usArbReg1 & CAN_IF1ARB2_DIR)) ||
((usMsgCtrl & CAN_IF1MCTL_TXRQST) && (!(usArbReg1 & CAN_IF1ARB2_DIR))))
{
pMsgObject->ulFlags |= MSG_OBJ_REMOTE_FRAME;
}
//
// Get the identifier out of the register, the format depends on size of
// the mask.
//
if(usArbReg1 & CAN_IF1ARB2_XTD)
{
//
// Set the 29 bit version of the Identifier for this message object.
//
pMsgObject->ulMsgID = ((usArbReg1 & CAN_IF1ARB2_ID_M) << 16) |
usArbReg0;
pMsgObject->ulFlags |= MSG_OBJ_EXTENDED_ID;
}
else
{
//
// The Identifier is an 11 bit value.
//
pMsgObject->ulMsgID = (usArbReg1 & CAN_IF1ARB2_ID_M) >> 2;
}
//
// Indicate that we lost some data.
//
if(usMsgCtrl & CAN_IF1MCTL_MSGLST)
{
pMsgObject->ulFlags |= MSG_OBJ_DATA_LOST;
}
//
// Set the flag to indicate if ID masking was used.
//
if(usMsgCtrl & CAN_IF1MCTL_UMASK)
{
if(usArbReg1 & CAN_IF1ARB2_XTD)
{
//
// The Identifier Mask is assumed to also be a 29 bit value.
//
pMsgObject->ulMsgIDMask =
((usMaskReg1 & CAN_IF1MSK2_IDMSK_M) << 16) | usMaskReg0;
//
// If this is a fully specified Mask and a remote frame then don't
// set the MSG_OBJ_USE_ID_FILTER because the ID was not really
// filtered.
//
if((pMsgObject->ulMsgIDMask != 0x1fffffff) ||
((pMsgObject->ulFlags & MSG_OBJ_REMOTE_FRAME) == 0))
{
pMsgObject->ulFlags |= MSG_OBJ_USE_ID_FILTER;
}
}
else
{
//
// The Identifier Mask is assumed to also be an 11 bit value.
//
pMsgObject->ulMsgIDMask = ((usMaskReg1 & CAN_IF1MSK2_IDMSK_M) >>
2);
//
// If this is a fully specified Mask and a remote frame then don't
// set the MSG_OBJ_USE_ID_FILTER because the ID was not really
// filtered.
//
if((pMsgObject->ulMsgIDMask != 0x7ff) ||
((pMsgObject->ulFlags & MSG_OBJ_REMOTE_FRAME) == 0))
{
pMsgObject->ulFlags |= MSG_OBJ_USE_ID_FILTER;
}
}
//
// Indicate if the extended bit was used in filtering.
//
if(usMaskReg1 & CAN_IF1MSK2_MXTD)
{
pMsgObject->ulFlags |= MSG_OBJ_USE_EXT_FILTER;
}
//
// Indicate if direction filtering was enabled.
//
if(usMaskReg1 & CAN_IF1MSK2_MDIR)
{
pMsgObject->ulFlags |= MSG_OBJ_USE_DIR_FILTER;
}
}
//
// Set the interrupt flags.
//
if(usMsgCtrl & CAN_IF1MCTL_TXIE)
{
pMsgObject->ulFlags |= MSG_OBJ_TX_INT_ENABLE;
}
if(usMsgCtrl & CAN_IF1MCTL_RXIE)
{
pMsgObject->ulFlags |= MSG_OBJ_RX_INT_ENABLE;
}
//
// See if there is new data available.
//
if(usMsgCtrl & CAN_IF1MCTL_NEWDAT)
{
//
// Get the amount of data needed to be read.
//
pMsgObject->ulMsgLen = (usMsgCtrl & CAN_IF1MCTL_DLC_M);
//
// Don't read any data for a remote frame, there is nothing valid in
// that buffer anyway.
//
if((pMsgObject->ulFlags & MSG_OBJ_REMOTE_FRAME) == 0)
{
//
// Read out the data from the CAN registers.
//
CANDataRegRead(pMsgObject->pucMsgData,
(unsigned long *)(ulBase + CAN_O_IF2DA1),
pMsgObject->ulMsgLen);
}
//
// Now clear out the new data flag.
//
CANRegWrite(ulBase + CAN_O_IF2CMSK, CAN_IF1CMSK_NEWDAT);
//
// Transfer the message object to the message object specified by
// ulObjID.
//
CANRegWrite(ulBase + CAN_O_IF2CRQ, ulObjID & CAN_IF1CRQ_MNUM_M);
//
// Wait for busy bit to clear
//
while(CANRegRead(ulBase + CAN_O_IF2CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Indicate that there is new data in this message.
//
pMsgObject->ulFlags |= MSG_OBJ_NEW_DATA;
}
else
{
//
// Along with the MSG_OBJ_NEW_DATA not being set the amount of data
// needs to be set to zero if none was available.
//
pMsgObject->ulMsgLen = 0;
}
}
//*****************************************************************************
//
//! Clears a message object so that it is no longer used.
//!
//! \param ulBase is the base address of the CAN controller.
//! \param ulObjID is the message object number to disable (1-32).
//!
//! This function frees the specified message object from use. Once a message
//! object has been ``cleared,'' it no longer automatically sends or
//! receives messages, nor does it generate interrupts.
//!
//! \return None.
//
//*****************************************************************************
void
CANMessageClear(unsigned long ulBase, unsigned long ulObjID)
{
//
// Check the arguments.
//
ASSERT(CANBaseValid(ulBase));
ASSERT((ulObjID >= 1) && (ulObjID <= 32));
//
// Wait for busy bit to clear
//
while(CANRegRead(ulBase + CAN_O_IF1CRQ) & CAN_IF1CRQ_BUSY)
{
}
//
// Clear the message value bit in the arbitration register. This indicates
// the message is not valid.
//
CANRegWrite(ulBase + CAN_O_IF1CMSK, CAN_IF1CMSK_WRNRD | CAN_IF1CMSK_ARB);
CANRegWrite(ulBase + CAN_O_IF1ARB1, 0);
CANRegWrite(ulBase + CAN_O_IF1ARB2, 0);
//
// Initiate programming the message object
//
CANRegWrite(ulBase + CAN_O_IF1CRQ, ulObjID & CAN_IF1CRQ_MNUM_M);
}
//*****************************************************************************
//
// Close the Doxygen group.
//! @}
//
//*****************************************************************************
View Git Blame Copy Permalink