269 lines
13 KiB
C
269 lines
13 KiB
C
/*
|
|
* The Clear BSD License
|
|
* Copyright (c) 2016, Freescale Semiconductor, Inc.
|
|
* Copyright 2016-2017 NXP
|
|
* All rights reserved.
|
|
*
|
|
* Redistribution and use in source and binary forms, with or without modification,
|
|
* are permitted (subject to the limitations in the disclaimer below) provided
|
|
* that the following conditions are met:
|
|
*
|
|
* o Redistributions of source code must retain the above copyright notice, this list
|
|
* of conditions and the following disclaimer.
|
|
*
|
|
* o Redistributions in binary form must reproduce the above copyright notice, this
|
|
* list of conditions and the following disclaimer in the documentation and/or
|
|
* other materials provided with the distribution.
|
|
*
|
|
* o Neither the name of the copyright holder nor the names of its
|
|
* contributors may be used to endorse or promote products derived from this
|
|
* software without specific prior written permission.
|
|
*
|
|
* NO EXPRESS OR IMPLIED LICENSES TO ANY PARTY'S PATENT RIGHTS ARE GRANTED BY THIS LICENSE.
|
|
* THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND
|
|
* ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
* WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
|
|
* DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR
|
|
* ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES
|
|
* (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES;
|
|
* LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON
|
|
* ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
|
|
* (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS
|
|
* SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#ifndef _FSL_FLASHIAP_H_
|
|
#define _FSL_FLASHIAP_H_
|
|
|
|
#include "fsl_common.h"
|
|
|
|
/*!
|
|
* @addtogroup flashiap_driver
|
|
* @{
|
|
*/
|
|
|
|
/*! @file */
|
|
|
|
/*******************************************************************************
|
|
* Definitions
|
|
******************************************************************************/
|
|
|
|
/*! @name Driver version */
|
|
/*@{*/
|
|
#define FSL_FLASHIAP_DRIVER_VERSION (MAKE_VERSION(2, 0, 0)) /*!< Version 2.0.0. */
|
|
/*@}*/
|
|
|
|
/*!
|
|
* @brief Flashiap status codes.
|
|
*/
|
|
enum _flashiap_status
|
|
{
|
|
kStatus_FLASHIAP_Success = kStatus_Success, /*!< Api is executed successfully */
|
|
kStatus_FLASHIAP_InvalidCommand = MAKE_STATUS(kStatusGroup_FLASHIAP, 1U), /*!< Invalid command */
|
|
kStatus_FLASHIAP_SrcAddrError =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 2U), /*!< Source address is not on word boundary */
|
|
kStatus_FLASHIAP_DstAddrError =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 3U), /*!< Destination address is not on a correct boundary */
|
|
kStatus_FLASHIAP_SrcAddrNotMapped =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 4U), /*!< Source address is not mapped in the memory map */
|
|
kStatus_FLASHIAP_DstAddrNotMapped =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 5U), /*!< Destination address is not mapped in the memory map */
|
|
kStatus_FLASHIAP_CountError =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 6U), /*!< Byte count is not multiple of 4 or is not a permitted value */
|
|
kStatus_FLASHIAP_InvalidSector =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP,
|
|
7), /*!< Sector number is invalid or end sector number is greater than start sector number */
|
|
kStatus_FLASHIAP_SectorNotblank = MAKE_STATUS(kStatusGroup_FLASHIAP, 8U), /*!< One or more sectors are not blank */
|
|
kStatus_FLASHIAP_NotPrepared =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 9U), /*!< Command to prepare sector for write operation was not executed */
|
|
kStatus_FLASHIAP_CompareError =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 10U), /*!< Destination and source memory contents do not match */
|
|
kStatus_FLASHIAP_Busy =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 11U), /*!< Flash programming hardware interface is busy */
|
|
kStatus_FLASHIAP_ParamError =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 12U), /*!< Insufficient number of parameters or invalid parameter */
|
|
kStatus_FLASHIAP_AddrError = MAKE_STATUS(kStatusGroup_FLASHIAP, 13U), /*!< Address is not on word boundary */
|
|
kStatus_FLASHIAP_AddrNotMapped =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 14U), /*!< Address is not mapped in the memory map */
|
|
kStatus_FLASHIAP_NoPower = MAKE_STATUS(kStatusGroup_FLASHIAP, 24U), /*!< Flash memory block is powered down */
|
|
kStatus_FLASHIAP_NoClock =
|
|
MAKE_STATUS(kStatusGroup_FLASHIAP, 27U), /*!< Flash memory block or controller is not clocked */
|
|
};
|
|
|
|
/*!
|
|
* @brief Flashiap command codes.
|
|
*/
|
|
enum _flashiap_commands
|
|
{
|
|
kIapCmd_FLASHIAP_PrepareSectorforWrite = 50U, /*!< Prepare Sector for write */
|
|
kIapCmd_FLASHIAP_CopyRamToFlash = 51U, /*!< Copy RAM to flash */
|
|
kIapCmd_FLASHIAP_EraseSector = 52U, /*!< Erase Sector */
|
|
kIapCmd_FLASHIAP_BlankCheckSector = 53U, /*!< Blank check sector */
|
|
kIapCmd_FLASHIAP_ReadPartId = 54U, /*!< Read part id */
|
|
kIapCmd_FLASHIAP_Read_BootromVersion = 55U, /*!< Read bootrom version */
|
|
kIapCmd_FLASHIAP_Compare = 56U, /*!< Compare */
|
|
kIapCmd_FLASHIAP_ReinvokeISP = 57U, /*!< Reinvoke ISP */
|
|
kIapCmd_FLASHIAP_ReadUid = 58U, /*!< Read Uid isp */
|
|
kIapCmd_FLASHIAP_ErasePage = 59U, /*!< Erase Page */
|
|
kIapCmd_FLASHIAP_ReadMisr = 70U, /*!< Read Misr */
|
|
kIapCmd_FLASHIAP_ReinvokeI2cSpiISP = 71U /*!< Reinvoke I2C/SPI isp */
|
|
};
|
|
|
|
/*! @brief IAP_ENTRY API function type */
|
|
typedef void (*IAP_ENTRY_T)(uint32_t cmd[5], uint32_t stat[4]);
|
|
|
|
/*******************************************************************************
|
|
* API
|
|
******************************************************************************/
|
|
|
|
#if defined(__cplusplus)
|
|
extern "C" {
|
|
#endif
|
|
|
|
/*!
|
|
* @brief IAP_ENTRY API function type
|
|
*
|
|
* Wrapper for rom iap call
|
|
*
|
|
* @param cmd_param IAP command and relevant parameter array.
|
|
* @param status_result IAP status result array.
|
|
*
|
|
* @retval None. Status/Result is returned via status_result array.
|
|
*/
|
|
static inline void iap_entry(uint32_t *cmd_param, uint32_t *status_result)
|
|
{
|
|
((IAP_ENTRY_T)FSL_FEATURE_SYSCON_IAP_ENTRY_LOCATION)(cmd_param, status_result);
|
|
}
|
|
|
|
/*!
|
|
* @brief Prepare sector for write operation
|
|
|
|
* This function prepares sector(s) for write/erase operation. This function must be
|
|
* called before calling the FLASHIAP_CopyRamToFlash() or FLASHIAP_EraseSector() or
|
|
* FLASHIAP_ErasePage() function. The end sector must be greater than or equal to
|
|
* start sector number.
|
|
*
|
|
* @param startSector Start sector number.
|
|
* @param endSector End sector number.
|
|
*
|
|
* @retval #kStatus_FLASHIAP_Success Api was executed successfully.
|
|
* @retval #kStatus_FLASHIAP_NoPower Flash memory block is powered down.
|
|
* @retval #kStatus_FLASHIAP_NoClock Flash memory block or controller is not clocked.
|
|
* @retval #kStatus_FLASHIAP_InvalidSector Sector number is invalid or end sector number
|
|
* is greater than start sector number.
|
|
* @retval #kStatus_FLASHIAP_Busy Flash programming hardware interface is busy.
|
|
*/
|
|
status_t FLASHIAP_PrepareSectorForWrite(uint32_t startSector, uint32_t endSector);
|
|
|
|
/*!
|
|
* @brief Copy RAM to flash.
|
|
|
|
* This function programs the flash memory. Corresponding sectors must be prepared
|
|
* via FLASHIAP_PrepareSectorForWrite before calling calling this function. The addresses
|
|
* should be a 256 byte boundary and the number of bytes should be 256 | 512 | 1024 | 4096.
|
|
*
|
|
* @param dstAddr Destination flash address where data bytes are to be written.
|
|
* @param srcAddr Source ram address from where data bytes are to be read.
|
|
* @param numOfBytes Number of bytes to be written.
|
|
* @param systemCoreClock SystemCoreClock in Hz. It is converted to KHz before calling the
|
|
* rom IAP function.
|
|
*
|
|
* @retval #kStatus_FLASHIAP_Success Api was executed successfully.
|
|
* @retval #kStatus_FLASHIAP_NoPower Flash memory block is powered down.
|
|
* @retval #kStatus_FLASHIAP_NoClock Flash memory block or controller is not clocked.
|
|
* @retval #kStatus_FLASHIAP_SrcAddrError Source address is not on word boundary.
|
|
* @retval #kStatus_FLASHIAP_DstAddrError Destination address is not on a correct boundary.
|
|
* @retval #kStatus_FLASHIAP_SrcAddrNotMapped Source address is not mapped in the memory map.
|
|
* @retval #kStatus_FLASHIAP_DstAddrNotMapped Destination address is not mapped in the memory map.
|
|
* @retval #kStatus_FLASHIAP_CountError Byte count is not multiple of 4 or is not a permitted value.
|
|
* @retval #kStatus_FLASHIAP_NotPrepared Command to prepare sector for write operation was not executed.
|
|
* @retval #kStatus_FLASHIAP_Busy Flash programming hardware interface is busy.
|
|
*/
|
|
status_t FLASHIAP_CopyRamToFlash(uint32_t dstAddr, uint32_t *srcAddr, uint32_t numOfBytes, uint32_t systemCoreClock);
|
|
|
|
/*!
|
|
* @brief Erase sector
|
|
|
|
* This function erases sector(s). The end sector must be greater than or equal to
|
|
* start sector number. FLASHIAP_PrepareSectorForWrite must be called before
|
|
* calling this function.
|
|
*
|
|
* @param startSector Start sector number.
|
|
* @param endSector End sector number.
|
|
* @param systemCoreClock SystemCoreClock in Hz. It is converted to KHz before calling the
|
|
* rom IAP function.
|
|
*
|
|
* @retval #kStatus_FLASHIAP_Success Api was executed successfully.
|
|
* @retval #kStatus_FLASHIAP_NoPower Flash memory block is powered down.
|
|
* @retval #kStatus_FLASHIAP_NoClock Flash memory block or controller is not clocked.
|
|
* @retval #kStatus_FLASHIAP_InvalidSector Sector number is invalid or end sector number
|
|
* is greater than start sector number.
|
|
* @retval #kStatus_FLASHIAP_NotPrepared Command to prepare sector for write operation was not executed.
|
|
* @retval #kStatus_FLASHIAP_Busy Flash programming hardware interface is busy.
|
|
*/
|
|
status_t FLASHIAP_EraseSector(uint32_t startSector, uint32_t endSector, uint32_t systemCoreClock);
|
|
|
|
/*!
|
|
|
|
* This function erases page(s). The end page must be greater than or equal to
|
|
* start page number. Corresponding sectors must be prepared via FLASHIAP_PrepareSectorForWrite
|
|
* before calling calling this function.
|
|
*
|
|
* @param startPage Start page number
|
|
* @param endPage End page number
|
|
* @param systemCoreClock SystemCoreClock in Hz. It is converted to KHz before calling the
|
|
* rom IAP function.
|
|
*
|
|
* @retval #kStatus_FLASHIAP_Success Api was executed successfully.
|
|
* @retval #kStatus_FLASHIAP_NoPower Flash memory block is powered down.
|
|
* @retval #kStatus_FLASHIAP_NoClock Flash memory block or controller is not clocked.
|
|
* @retval #kStatus_FLASHIAP_InvalidSector Page number is invalid or end page number
|
|
* is greater than start page number
|
|
* @retval #kStatus_FLASHIAP_NotPrepared Command to prepare sector for write operation was not executed.
|
|
* @retval #kStatus_FLASHIAP_Busy Flash programming hardware interface is busy.
|
|
*/
|
|
status_t FLASHIAP_ErasePage(uint32_t startPage, uint32_t endPage, uint32_t systemCoreClock);
|
|
|
|
/*!
|
|
* @brief Blank check sector(s)
|
|
*
|
|
* Blank check single or multiples sectors of flash memory. The end sector must be greater than or equal to
|
|
* start sector number. It can be used to verify the sector eraseure after FLASHIAP_EraseSector call.
|
|
*
|
|
* @param startSector : Start sector number. Must be greater than or equal to start sector number
|
|
* @param endSector : End sector number
|
|
* @retval #kStatus_FLASHIAP_Success One or more sectors are in erased state.
|
|
* @retval #kStatus_FLASHIAP_NoPower Flash memory block is powered down.
|
|
* @retval #kStatus_FLASHIAP_NoClock Flash memory block or controller is not clocked.
|
|
* @retval #kStatus_FLASHIAP_SectorNotblank One or more sectors are not blank.
|
|
*/
|
|
status_t FLASHIAP_BlankCheckSector(uint32_t startSector, uint32_t endSector);
|
|
|
|
/*!
|
|
* @brief Compare memory contents of flash with ram.
|
|
|
|
* This function compares the contents of flash and ram. It can be used to verify the flash
|
|
* memory contents after FLASHIAP_CopyRamToFlash call.
|
|
*
|
|
* @param dstAddr Destination flash address.
|
|
* @param srcAddr Source ram address.
|
|
* @param numOfBytes Number of bytes to be compared.
|
|
*
|
|
* @retval #kStatus_FLASHIAP_Success Contents of flash and ram match.
|
|
* @retval #kStatus_FLASHIAP_NoPower Flash memory block is powered down.
|
|
* @retval #kStatus_FLASHIAP_NoClock Flash memory block or controller is not clocked.
|
|
* @retval #kStatus_FLASHIAP_AddrError Address is not on word boundary.
|
|
* @retval #kStatus_FLASHIAP_AddrNotMapped Address is not mapped in the memory map.
|
|
* @retval #kStatus_FLASHIAP_CountError Byte count is not multiple of 4 or is not a permitted value.
|
|
* @retval #kStatus_FLASHIAP_CompareError Destination and source memory contents do not match.
|
|
*/
|
|
status_t FLASHIAP_Compare(uint32_t dstAddr, uint32_t *srcAddr, uint32_t numOfBytes);
|
|
|
|
#ifdef __cplusplus
|
|
}
|
|
#endif
|
|
|
|
/*@}*/
|
|
|
|
#endif /* _FSL_FLASHIAP_H_ */
|