228 lines
8.1 KiB
C
228 lines
8.1 KiB
C
/*!
|
|
\file gd32f3x0_syscfg.c
|
|
\brief SYSCFG driver
|
|
|
|
\version 2017-06-06, V1.0.0, firmware for GD32F3x0
|
|
\version 2019-06-01, V2.0.0, firmware for GD32F3x0
|
|
*/
|
|
|
|
/*
|
|
Copyright (c) 2019, GigaDevice Semiconductor Inc.
|
|
|
|
Redistribution and use in source and binary forms, with or without modification,
|
|
are permitted provided that the following conditions are met:
|
|
|
|
1. Redistributions of source code must retain the above copyright notice, this
|
|
list of conditions and the following disclaimer.
|
|
2. Redistributions in binary form must reproduce the above copyright notice,
|
|
this list of conditions and the following disclaimer in the documentation
|
|
and/or other materials provided with the distribution.
|
|
3. Neither the name of the copyright holder nor the names of its contributors
|
|
may be used to endorse or promote products derived from this software without
|
|
specific prior written permission.
|
|
|
|
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
|
|
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
|
|
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
|
|
IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
|
|
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
|
|
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
|
|
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
|
|
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
|
|
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
|
|
OF SUCH DAMAGE.
|
|
*/
|
|
|
|
#include "gd32f3x0_syscfg.h"
|
|
|
|
/*!
|
|
\brief reset the SYSCFG registers
|
|
\param[in] none
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_deinit(void)
|
|
{
|
|
rcu_periph_reset_enable(RCU_CFGCMPRST);
|
|
rcu_periph_reset_disable(RCU_CFGCMPRST);
|
|
}
|
|
|
|
/*!
|
|
\brief enable the DMA channels remapping
|
|
\param[in] syscfg_dma_remap: specify the DMA channels to remap
|
|
one or more parameters can be selected which is shown as below:
|
|
\arg SYSCFG_DMA_REMAP_TIMER16: remap TIMER16 channel0 and UP DMA requests to channel1(defaut channel0)
|
|
\arg SYSCFG_DMA_REMAP_TIMER15: remap TIMER15 channel2 and UP DMA requests to channel3(defaut channel2)
|
|
\arg SYSCFG_DMA_REMAP_USART0RX: remap USART0 Rx DMA request to channel4(default channel2)
|
|
\arg SYSCFG_DMA_REMAP_USART0TX: remap USART0 Tx DMA request to channel3(default channel1)
|
|
\arg SYSCFG_DMA_REMAP_ADC: remap ADC DMA requests from channel0 to channel1
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_dma_remap_enable(uint32_t syscfg_dma_remap)
|
|
{
|
|
SYSCFG_CFG0 |= syscfg_dma_remap;
|
|
}
|
|
|
|
/*!
|
|
\brief disable the DMA channels remapping
|
|
\param[in] syscfg_dma_remap: specify the DMA channels to remap
|
|
one or more parameters can be selected which is shown as below:
|
|
\arg SYSCFG_DMA_REMAP_TIMER16: remap TIMER16 channel0 and UP DMA requests to channel1(defaut channel0)
|
|
\arg SYSCFG_DMA_REMAP_TIMER15: remap TIMER15 channel2 and UP DMA requests to channel3(defaut channel2)
|
|
\arg SYSCFG_DMA_REMAP_USART0RX: remap USART0 Rx DMA request to channel4(default channel2)
|
|
\arg SYSCFG_DMA_REMAP_USART0TX: remap USART0 Tx DMA request to channel3(default channel1)
|
|
\arg SYSCFG_DMA_REMAP_ADC: remap ADC DMA requests from channel0 to channel1
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_dma_remap_disable(uint32_t syscfg_dma_remap)
|
|
{
|
|
SYSCFG_CFG0 &= ~syscfg_dma_remap;
|
|
}
|
|
|
|
/*!
|
|
\brief enable PB9 high current capability
|
|
\param[in] none
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_high_current_enable(void)
|
|
{
|
|
SYSCFG_CFG0 |= SYSCFG_HIGH_CURRENT_ENABLE;
|
|
}
|
|
|
|
/*!
|
|
\brief disable PB9 high current capability
|
|
\param[in] none
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_high_current_disable(void)
|
|
{
|
|
SYSCFG_CFG0 &= SYSCFG_HIGH_CURRENT_DISABLE;
|
|
}
|
|
|
|
/*!
|
|
\brief configure the GPIO pin as EXTI Line
|
|
\param[in] exti_port: specify the GPIO port used in EXTI
|
|
only one parameter can be selected which is shown as below:
|
|
\arg EXTI_SOURCE_GPIOx(x = A,B,C,D,F): EXTI GPIO port
|
|
\param[in] exti_pin: specify the EXTI line
|
|
only one parameter can be selected which is shown as below:
|
|
\arg EXTI_SOURCE_PINx(x = 0..15): EXTI GPIO pin
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_exti_line_config(uint8_t exti_port, uint8_t exti_pin)
|
|
{
|
|
uint32_t clear_exti_mask = ~((uint32_t)EXTI_SS_MASK << (EXTI_SS_MSTEP(exti_pin)));
|
|
uint32_t config_exti_mask = ((uint32_t)exti_port) << (EXTI_SS_MSTEP(exti_pin));
|
|
|
|
switch(exti_pin / EXTI_SS_JSTEP){
|
|
case EXTISS0:
|
|
/* clear EXTI source line(0..3) */
|
|
SYSCFG_EXTISS0 &= clear_exti_mask;
|
|
/* configure EXTI soure line(0..3) */
|
|
SYSCFG_EXTISS0 |= config_exti_mask;
|
|
break;
|
|
case EXTISS1:
|
|
/* clear EXTI soure line(4..7) */
|
|
SYSCFG_EXTISS1 &= clear_exti_mask;
|
|
/* configure EXTI soure line(4..7) */
|
|
SYSCFG_EXTISS1 |= config_exti_mask;
|
|
break;
|
|
case EXTISS2:
|
|
/* clear EXTI soure line(8..11) */
|
|
SYSCFG_EXTISS2 &= clear_exti_mask;
|
|
/* configure EXTI soure line(8..11) */
|
|
SYSCFG_EXTISS2 |= config_exti_mask;
|
|
break;
|
|
case EXTISS3:
|
|
/* clear EXTI soure line(12..15) */
|
|
SYSCFG_EXTISS3 &= clear_exti_mask;
|
|
/* configure EXTI soure line(12..15) */
|
|
SYSCFG_EXTISS3 |= config_exti_mask;
|
|
break;
|
|
default:
|
|
break;
|
|
}
|
|
}
|
|
|
|
/*!
|
|
\brief connect TIMER0/14/15/16 break input to the selected parameter
|
|
\param[in] syscfg_lock: Specify the parameter to be connected
|
|
one or more parameters can be selected which is shown as below:
|
|
\arg SYSCFG_LOCK_LOCKUP: Cortex-M4 lockup output connected to the break input
|
|
\arg SYSCFG_LOCK_SRAM_PARITY_ERROR: SRAM_PARITY check error connected to the break input
|
|
\arg SYSCFG_LOCK_LVD: LVD interrupt connected to the break input
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_lock_config(uint32_t syscfg_lock)
|
|
{
|
|
SYSCFG_CFG2 |= syscfg_lock;
|
|
}
|
|
|
|
/*!
|
|
\brief check if the specified flag in SYSCFG_CFG2 is set or not.
|
|
\param[in] syscfg_flag: specify the flag in SYSCFG_CFG2 to check.
|
|
\arg SYSCFG_SRAM_PCEF: SRAM parity check error flag.
|
|
\param[out] none
|
|
\retval the syscfg_flag state returned (SET or RESET).
|
|
*/
|
|
FlagStatus syscfg_flag_get(uint32_t syscfg_flag)
|
|
{
|
|
if((SYSCFG_CFG2 & syscfg_flag) != (uint32_t)RESET){
|
|
return SET;
|
|
}else{
|
|
return RESET;
|
|
}
|
|
}
|
|
|
|
/*!
|
|
\brief clear the flag in SYSCFG_CFG2 by writing 1.
|
|
\param[in] syscfg_flag: Specify the flag in SYSCFG_CFG2 to clear.
|
|
\arg SYSCFG_SRAM_PCEF: SRAM parity check error flag.
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_flag_clear(uint32_t syscfg_flag)
|
|
{
|
|
SYSCFG_CFG2 |= (uint32_t) syscfg_flag;
|
|
}
|
|
|
|
/*!
|
|
\brief configure the I/O compensation cell
|
|
\param[in] syscfg_compensation: specifies the I/O compensation cell mode
|
|
only one parameter can be selected which is shown as below:
|
|
\arg SYSCFG_COMPENSATION_ENABLE: I/O compensation cell is enabled
|
|
\arg SYSCFG_COMPENSATION_DISABLE: I/O compensation cell is disabled
|
|
\param[out] none
|
|
\retval none
|
|
*/
|
|
void syscfg_compensation_config(uint32_t syscfg_compensation)
|
|
{
|
|
uint32_t reg;
|
|
|
|
reg = SYSCFG_CPSCTL;
|
|
/* reset the SYSCFG_CPSCTL_CPS_EN bit and set according to syscfg_compensation */
|
|
reg &= ~SYSCFG_CPSCTL_CPS_EN;
|
|
SYSCFG_CPSCTL = (reg | syscfg_compensation);
|
|
}
|
|
|
|
/*!
|
|
\brief check if the I/O compensation cell ready flag is set or not
|
|
\param[in] none
|
|
\param[out] none
|
|
\retval FlagStatus: SET or RESET
|
|
*/
|
|
FlagStatus syscfg_cps_rdy_flag_get(void)
|
|
{
|
|
if(((uint32_t)RESET) != (SYSCFG_CPSCTL & SYSCFG_CPSCTL_CPS_RDY)){
|
|
return SET;
|
|
}else{
|
|
return RESET;
|
|
}
|
|
}
|