libs/rt-thread
libs
/
rt-thread
4
0
Fork 0
Code Issues Pull Requests Projects Releases Wiki Activity
rt-thread/bsp/gd32350r-eval/Libraries/GD32F3x0_standard_peripheral/Source/gd32f3x0_spi.c

793 lines
24 KiB
C
Raw Blame History

/*!
\file gd32f3x0_spi.c
\brief SPI driver
\version 2017-06-06, V1.0.0, firmware for GD32F3x0
\version 2019-06-01, V2.0.0, firmware for GD32F3x0
*/
/*
Copyright (c) 2019, GigaDevice Semiconductor Inc.
Redistribution and use in source and binary forms, with or without modification,
are permitted provided that the following conditions are met:
1. Redistributions of source code must retain the above copyright notice, this
list of conditions and the following disclaimer.
2. Redistributions in binary form must reproduce the above copyright notice,
this list of conditions and the following disclaimer in the documentation
and/or other materials provided with the distribution.
3. Neither the name of the copyright holder nor the names of its contributors
may be used to endorse or promote products derived from this software without
specific prior written permission.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED
WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT,
INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT
NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR
PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY
OF SUCH DAMAGE.
*/
#include "gd32f3x0_spi.h"
#define SPI_INIT_MASK ((uint32_t)0x00003040U) /*!< SPI parameter initialization mask */
#define I2S_INIT_MASK ((uint32_t)0x0000F047U) /*!< I2S parameter initialization mask */
#define SPI_I2SPSC_DEFAULT_VALUE ((uint32_t)0x00000002U) /*!< default value of SPI_I2SPSC register */
/*!
\brief reset SPI and I2S
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_i2s_deinit(uint32_t spi_periph)
{
switch(spi_periph){
case SPI0:
/* reset SPI0 and I2S0 */
rcu_periph_reset_enable(RCU_SPI0RST);
rcu_periph_reset_disable(RCU_SPI0RST);
break;
case SPI1:
/* reset SPI1 */
rcu_periph_reset_enable(RCU_SPI1RST);
rcu_periph_reset_disable(RCU_SPI1RST);
break;
default :
break;
}
}
/*!
\brief initialize the parameters of SPI struct with the default values
\param[in] spi_struct: SPI parameter stuct
\param[out] none
\retval none
*/
void spi_struct_para_init(spi_parameter_struct* spi_struct)
{
/* set the SPI struct with the default values */
spi_struct->device_mode = SPI_SLAVE;
spi_struct->trans_mode = SPI_TRANSMODE_FULLDUPLEX;
spi_struct->frame_size = SPI_FRAMESIZE_8BIT;
spi_struct->nss = SPI_NSS_HARD;
spi_struct->clock_polarity_phase = SPI_CK_PL_LOW_PH_1EDGE;
spi_struct->prescale = SPI_PSC_2;
}
/*!
\brief initialize SPI parameter
\param[in] spi_periph: SPIx(x=0,1)
\param[in] spi_struct: SPI parameter initialization stuct members of the structure
and the member values are shown as below:
device_mode: SPI_MASTER, SPI_SLAVE
trans_mode: SPI_TRANSMODE_FULLDUPLEX, SPI_TRANSMODE_RECEIVEONLY,
SPI_TRANSMODE_BDRECEIVE, SPI_TRANSMODE_BDTRANSMIT
frame_size: SPI_FRAMESIZE_16BIT, SPI_FRAMESIZE_8BIT
nss: SPI_NSS_SOFT, SPI_NSS_HARD
endian: SPI_ENDIAN_MSB, SPI_ENDIAN_LSB
clock_polarity_phase: SPI_CK_PL_LOW_PH_1EDGE, SPI_CK_PL_HIGH_PH_1EDGE
SPI_CK_PL_LOW_PH_2EDGE, SPI_CK_PL_HIGH_PH_2EDGE
prescale: SPI_PSC_n (n=2,4,8,16,32,64,128,256)
\param[out] none
\retval none
*/
void spi_init(uint32_t spi_periph, spi_parameter_struct* spi_struct)
{
uint32_t reg = 0U;
reg = SPI_CTL0(spi_periph);
reg &= SPI_INIT_MASK;
/* select SPI as master or slave */
reg |= spi_struct->device_mode;
/* select SPI transfer mode */
reg |= spi_struct->trans_mode;
/* select SPI frame size */
reg |= spi_struct->frame_size;
/* select SPI NSS use hardware or software */
reg |= spi_struct->nss;
/* select SPI LSB or MSB */
reg |= spi_struct->endian;
/* select SPI polarity and phase */
reg |= spi_struct->clock_polarity_phase;
/* select SPI prescale to adjust transmit speed */
reg |= spi_struct->prescale;
/* write to SPI_CTL0 register */
SPI_CTL0(spi_periph) = (uint32_t)reg;
/* select SPI mode */
SPI_I2SCTL(spi_periph) &= (uint32_t)(~SPI_I2SCTL_I2SSEL);
}
/*!
\brief enable SPI
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_enable(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_SPIEN;
}
/*!
\brief disable SPI
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_disable(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_SPIEN);
}
#ifdef GD32F350
/*!
\brief initialize I2S parameter
\param[in] spi_periph: SPI0
\param[in] mode: I2S operation mode
only one parameter can be selected which is shown as below:
\arg I2S_MODE_SLAVETX: I2S slave transmit mode
\arg I2S_MODE_SLAVERX: I2S slave receive mode
\arg I2S_MODE_MASTERTX: I2S master transmit mode
\arg I2S_MODE_MASTERRX: I2S master receive mode
\param[in] standard: I2S standard
only one parameter can be selected which is shown as below:
\arg I2S_STD_PHILLIPS: I2S phillips standard
\arg I2S_STD_MSB: I2S MSB standard
\arg I2S_STD_LSB: I2S LSB standard
\arg I2S_STD_PCMSHORT: I2S PCM short standard
\arg I2S_STD_PCMLONG: I2S PCM long standard
\param[in] ckpl: I2S idle state clock polarity
only one parameter can be selected which is shown as below:
\arg I2S_CKPL_LOW: I2S clock polarity low level
\arg I2S_CKPL_HIGH: I2S clock polarity high level
\param[out] none
\retval none
*/
void i2s_init(uint32_t spi_periph, uint32_t mode, uint32_t standard, uint32_t ckpl)
{
uint32_t reg = 0U;
reg = SPI_I2SCTL(spi_periph);
reg &= I2S_INIT_MASK;
/* enable I2S mode */
reg |= (uint32_t)SPI_I2SCTL_I2SSEL;
/* select I2S mode */
reg |= (uint32_t)mode;
/* select I2S standard */
reg |= (uint32_t)standard;
/* select I2S polarity */
reg |= (uint32_t)ckpl;
/* write to SPI_I2SCTL register */
SPI_I2SCTL(spi_periph) = (uint32_t)reg;
}
/*!
\brief configure I2S prescaler
\param[in] spi_periph: SPI0
\param[in] audiosample: I2S audio sample rate
only one parameter can be selected which is shown as below:
\arg I2S_AUDIOSAMPLE_8K: audio sample rate is 8KHz
\arg I2S_AUDIOSAMPLE_11K: audio sample rate is 11KHz
\arg I2S_AUDIOSAMPLE_16K: audio sample rate is 16KHz
\arg I2S_AUDIOSAMPLE_22K: audio sample rate is 22KHz
\arg I2S_AUDIOSAMPLE_32K: audio sample rate is 32KHz
\arg I2S_AUDIOSAMPLE_44K: audio sample rate is 44KHz
\arg I2S_AUDIOSAMPLE_48K: audio sample rate is 48KHz
\arg I2S_AUDIOSAMPLE_96K: audio sample rate is 96KHz
\arg I2S_AUDIOSAMPLE_192K: audio sample rate is 192KHz
\param[in] frameformat: I2S data length and channel length
only one parameter can be selected which is shown as below:
\arg I2S_FRAMEFORMAT_DT16B_CH16B: I2S data length is 16 bit and channel length is 16 bit
\arg I2S_FRAMEFORMAT_DT16B_CH32B: I2S data length is 16 bit and channel length is 32 bit
\arg I2S_FRAMEFORMAT_DT24B_CH32B: I2S data length is 24 bit and channel length is 32 bit
\arg I2S_FRAMEFORMAT_DT32B_CH32B: I2S data length is 32 bit and channel length is 32 bit
\param[in] mckout: I2S master clock output
only one parameter can be selected which is shown as below:
\arg I2S_MCKOUT_ENABLE: I2S master clock output enable
\arg I2S_MCKOUT_DISABLE: I2S master clock output disable
\param[out] none
\retval none
*/
void i2s_psc_config(uint32_t spi_periph, uint32_t audiosample, uint32_t frameformat, uint32_t mckout)
{
uint32_t i2sdiv = 2U, i2sof = 0U;
uint32_t clks = 0U;
uint32_t i2sclock = 0U;
/* deinit SPI_I2SPSC register */
SPI_I2SPSC(spi_periph) = SPI_I2SPSC_DEFAULT_VALUE;
/* get system clock */
i2sclock = rcu_clock_freq_get(CK_SYS);
/* config the prescaler depending on the mclk output state, the frame format and audio sample rate */
if(I2S_MCKOUT_ENABLE == mckout){
clks = (uint32_t)(((i2sclock / 256U) * 10U) / audiosample);
}else{
if(I2S_FRAMEFORMAT_DT16B_CH16B == frameformat){
clks = (uint32_t)(((i2sclock / 32U) *10U ) / audiosample);
}else{
clks = (uint32_t)(((i2sclock / 64U) *10U ) / audiosample);
}
}
/* remove the floating point */
clks = (clks + 5U) / 10U;
i2sof = (clks & 0x00000001U);
i2sdiv = ((clks - i2sof) / 2U);
i2sof = (i2sof << 8U);
/* set the default values */
if((i2sdiv < 2U) || (i2sdiv > 255U)){
i2sdiv = 2U;
i2sof = 0U;
}
/* configure SPI_I2SPSC */
SPI_I2SPSC(spi_periph) = (uint32_t)(i2sdiv | i2sof | mckout);
/* clear SPI_I2SCTL_DTLEN and SPI_I2SCTL_CHLEN bits */
SPI_I2SCTL(spi_periph) &= (uint32_t)(~(SPI_I2SCTL_DTLEN | SPI_I2SCTL_CHLEN));
/* configure data frame format */
SPI_I2SCTL(spi_periph) |= (uint32_t)frameformat;
}
/*!
\brief enable I2S
\param[in] spi_periph: SPI0
\param[out] none
\retval none
*/
void i2s_enable(uint32_t spi_periph)
{
SPI_I2SCTL(spi_periph) |= (uint32_t)SPI_I2SCTL_I2SEN;
}
/*!
\brief disable I2S
\param[in] spi_periph: SPI0
\param[out] none
\retval none
*/
void i2s_disable(uint32_t spi_periph)
{
SPI_I2SCTL(spi_periph) &= (uint32_t)(~SPI_I2SCTL_I2SEN);
}
#endif /* GD32F350 */
/*!
\brief enable SPI NSS output
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_nss_output_enable(uint32_t spi_periph)
{
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_NSSDRV;
}
/*!
\brief disable SPI NSS output
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_nss_output_disable(uint32_t spi_periph)
{
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_NSSDRV);
}
/*!
\brief SPI NSS pin high level in software mode
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_nss_internal_high(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_SWNSS;
}
/*!
\brief SPI NSS pin low level in software mode
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_nss_internal_low(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_SWNSS);
}
/*!
\brief enable SPI DMA send or receive
\param[in] spi_periph: SPIx(x=0,1)
\param[in] dma: SPI DMA mode
only one parameter can be selected which is shown as below:
\arg SPI_DMA_TRANSMIT: SPI transmit data using DMA
\arg SPI_DMA_RECEIVE: SPI receive data using DMA
\param[out] none
\retval none
*/
void spi_dma_enable(uint32_t spi_periph, uint8_t dma)
{
if(SPI_DMA_TRANSMIT == dma){
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_DMATEN;
}else{
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_DMAREN;
}
}
/*!
\brief disable SPI DMA send or receive
\param[in] spi_periph: SPIx(x=0,1)
\param[in] dma: SPI DMA mode
only one parameter can be selected which is shown as below:
\arg SPI_DMA_TRANSMIT: SPI transmit data using DMA
\arg SPI_DMA_RECEIVE: SPI receive data using DMA
\param[out] none
\retval none
*/
void spi_dma_disable(uint32_t spi_periph, uint8_t dma)
{
if(SPI_DMA_TRANSMIT == dma){
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_DMATEN);
}else{
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_DMAREN);
}
}
/*!
\brief configure SPI/I2S data frame format
\param[in] spi_periph: SPIx(x=0,1)
\param[in] frame_format: SPI frame size
only one parameter can be selected which is shown as below:
\arg SPI_FRAMESIZE_16BIT: SPI frame size is 16 bits
\arg SPI_FRAMESIZE_8BIT: SPI frame size is 8 bits
\param[out] none
\retval none
*/
void spi_i2s_data_frame_format_config(uint32_t spi_periph, uint16_t frame_format)
{
/* clear SPI_CTL0_FF16 bit */
SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_FF16);
/* confige SPI_CTL0_FF16 bit */
SPI_CTL0(spi_periph) |= (uint32_t)frame_format;
}
/*!
\brief SPI transmit data
\param[in] spi_periph: SPIx(x=0,1)
\param[in] data: 16-bit data
\param[out] none
\retval none
*/
void spi_i2s_data_transmit(uint32_t spi_periph, uint16_t data)
{
SPI_DATA(spi_periph) = (uint32_t)data;
}
/*!
\brief SPI receive data
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval 16-bit data
*/
uint16_t spi_i2s_data_receive(uint32_t spi_periph)
{
return ((uint16_t)SPI_DATA(spi_periph));
}
/*!
\brief configure SPI bidirectional transfer direction
\param[in] spi_periph: SPIx(x=0,1)
\param[in] transfer_direction: SPI transfer direction
only one parameter can be selected which is shown as below:
\arg SPI_BIDIRECTIONAL_TRANSMIT: SPI work in transmit-only mode
\arg SPI_BIDIRECTIONAL_RECEIVE: SPI work in receive-only mode
\param[out] none
\retval none
*/
void spi_bidirectional_transfer_config(uint32_t spi_periph, uint32_t transfer_direction)
{
if(SPI_BIDIRECTIONAL_TRANSMIT == transfer_direction){
/* set the transmit only mode */
SPI_CTL0(spi_periph) |= (uint32_t)SPI_BIDIRECTIONAL_TRANSMIT;
}else{
/* set the receive only mode */
SPI_CTL0(spi_periph) &= SPI_BIDIRECTIONAL_RECEIVE;
}
}
/*!
\brief set CRC polynomial
\param[in] spi_periph: SPIx(x=0,1)
\param[in] crc_poly: CRC polynomial value
\param[out] none
\retval none
*/
void spi_crc_polynomial_set(uint32_t spi_periph, uint16_t crc_poly)
{
/* enable SPI CRC */
SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_CRCEN;
/* set SPI CRC polynomial */
SPI_CRCPOLY(spi_periph) = (uint32_t)crc_poly;
}
/*!
\brief get SPI CRC polynomial
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval 16-bit CRC polynomial
*/
uint16_t spi_crc_polynomial_get(uint32_t spi_periph)
{
return ((uint16_t)SPI_CRCPOLY(spi_periph));
}
/*!
\brief turn on CRC function
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_crc_on(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_CRCEN;
}
/*!
\brief turn off CRC function
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_crc_off(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) &= (uint32_t)(~SPI_CTL0_CRCEN);
}
/*!
\brief SPI next data is CRC value
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_crc_next(uint32_t spi_periph)
{
SPI_CTL0(spi_periph) |= (uint32_t)SPI_CTL0_CRCNT;
}
/*!
\brief get SPI CRC send value or receive value
\param[in] spi_periph: SPIx(x=0,1)
\param[in] crc: SPI crc value
\arg SPI_CRC_TX: get transmit crc value
\arg SPI_CRC_RX: get receive crc value
\param[out] none
\retval 16-bit CRC value
*/
uint16_t spi_crc_get(uint32_t spi_periph, uint8_t crc)
{
if(SPI_CRC_TX == crc){
return ((uint16_t)(SPI_TCRC(spi_periph)));
}else{
return ((uint16_t)(SPI_RCRC(spi_periph)));
}
}
/*!
\brief enable SPI TI mode
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_ti_mode_enable(uint32_t spi_periph)
{
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_TMOD;
}
/*!
\brief disable SPI TI mode
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_ti_mode_disable(uint32_t spi_periph)
{
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_TMOD);
}
/*!
\brief enable SPI NSS pulse mode
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_nssp_mode_enable(uint32_t spi_periph)
{
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_NSSP;
}
/*!
\brief disable SPI NSS pulse mode
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_nssp_mode_disable(uint32_t spi_periph)
{
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_NSSP);
}
/*!
\brief enable quad wire SPI
\param[in] spi_periph: SPI1
\param[out] none
\retval none
*/
void qspi_enable(uint32_t spi_periph)
{
SPI_QCTL(spi_periph) |= (uint32_t)SPI_QCTL_QMOD;
}
/*!
\brief disable quad wire SPI
\param[in] spi_periph: SPI1
\param[out] none
\retval none
*/
void qspi_disable(uint32_t spi_periph)
{
SPI_QCTL(spi_periph) &= (uint32_t)(~SPI_QCTL_QMOD);
}
/*!
\brief enable quad wire SPI write
\param[in] spi_periph: SPI1
\param[out] none
\retval none
*/
void qspi_write_enable(uint32_t spi_periph)
{
SPI_QCTL(spi_periph) &= (uint32_t)(~SPI_QCTL_QRD);
}
/*!
\brief enable quad wire SPI read
\param[in] spi_periph: SPI1
\param[out] none
\retval none
*/
void qspi_read_enable(uint32_t spi_periph)
{
SPI_QCTL(spi_periph) |= (uint32_t)SPI_QCTL_QRD;
}
/*!
\brief enable SPI_IO2 and SPI_IO3 pin output
\param[in] spi_periph: SPI1
\param[out] none
\retval none
*/
void qspi_io23_output_enable(uint32_t spi_periph)
{
SPI_QCTL(spi_periph) |= (uint32_t)SPI_QCTL_IO23_DRV;
}
/*!
\brief disable SPI_IO2 and SPI_IO3 pin output
\param[in] spi_periph: SPI1
\param[out] none
\retval none
*/
void qspi_io23_output_disable(uint32_t spi_periph)
{
SPI_QCTL(spi_periph) &= (uint32_t)(~SPI_QCTL_IO23_DRV);
}
/*!
\brief enable SPI and I2S interrupt
\param[in] spi_periph: SPIx(x=0,1)
\param[in] interrupt: SPI/I2S interrupt
only one parameter can be selected which is shown as below:
\arg SPI_I2S_INT_TBE: transmit buffer empty interrupt
\arg SPI_I2S_INT_RBNE: receive buffer not empty interrupt
\arg SPI_I2S_INT_ERR: CRC error,configuration error,reception overrun error,
transmission underrun error and format error interrupt
\param[out] none
\retval none
*/
void spi_i2s_interrupt_enable(uint32_t spi_periph, uint8_t interrupt)
{
switch(interrupt){
/* SPI/I2S transmit buffer empty interrupt */
case SPI_I2S_INT_TBE:
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_TBEIE;
break;
/* SPI/I2S receive buffer not empty interrupt */
case SPI_I2S_INT_RBNE:
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_RBNEIE;
break;
/* SPI/I2S error */
case SPI_I2S_INT_ERR:
SPI_CTL1(spi_periph) |= (uint32_t)SPI_CTL1_ERRIE;
break;
default:
break;
}
}
/*!
\brief disable SPI and I2S interrupt
\param[in] spi_periph: SPIx(x=0,1)
\param[in] interrupt: SPI/I2S interrupt
only one parameter can be selected which is shown as below:
\arg SPI_I2S_INT_TBE: transmit buffer empty interrupt
\arg SPI_I2S_INT_RBNE: receive buffer not empty interrupt
\arg SPI_I2S_INT_ERR: CRC error,configuration error,reception overrun error,
transmission underrun error and format error interrupt
\param[out] none
\retval none
*/
void spi_i2s_interrupt_disable(uint32_t spi_periph, uint8_t interrupt)
{
switch(interrupt){
/* SPI/I2S transmit buffer empty interrupt */
case SPI_I2S_INT_TBE:
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_TBEIE);
break;
/* SPI/I2S receive buffer not empty interrupt */
case SPI_I2S_INT_RBNE:
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_RBNEIE);
break;
/* SPI/I2S error */
case SPI_I2S_INT_ERR:
SPI_CTL1(spi_periph) &= (uint32_t)(~SPI_CTL1_ERRIE);
break;
default :
break;
}
}
/*!
\brief get SPI and I2S interrupt flag status
\param[in] spi_periph: SPIx(x=0,1)
\param[in] interrupt: SPI/I2S interrupt flag status
only one parameter can be selected which is shown as below:
\arg SPI_I2S_INT_FLAG_TBE: transmit buffer empty interrupt flag
\arg SPI_I2S_INT_FLAG_RBNE: receive buffer not empty interrupt flag
\arg SPI_I2S_INT_FLAG_RXORERR: overrun interrupt flag
\arg SPI_INT_FLAG_CONFERR: config error interrupt flag
\arg SPI_INT_FLAG_CRCERR: CRC error interrupt flag
\arg I2S_INT_FLAG_TXURERR: underrun error interrupt flag
\arg SPI_I2S_INT_FLAG_FERR: format error interrupt flag
\param[out] none
\retval FlagStatus: SET or RESET
*/
FlagStatus spi_i2s_interrupt_flag_get(uint32_t spi_periph, uint8_t interrupt)
{
uint32_t reg1 = SPI_STAT(spi_periph);
uint32_t reg2 = SPI_CTL1(spi_periph);
switch(interrupt){
/* SPI/I2S transmit buffer empty interrupt */
case SPI_I2S_INT_FLAG_TBE:
reg1 = reg1 & SPI_STAT_TBE;
reg2 = reg2 & SPI_CTL1_TBEIE;
break;
/* SPI/I2S receive buffer not empty interrupt */
case SPI_I2S_INT_FLAG_RBNE:
reg1 = reg1 & SPI_STAT_RBNE;
reg2 = reg2 & SPI_CTL1_RBNEIE;
break;
/* SPI/I2S overrun interrupt */
case SPI_I2S_INT_FLAG_RXORERR:
reg1 = reg1 & SPI_STAT_RXORERR;
reg2 = reg2 & SPI_CTL1_ERRIE;
break;
/* SPI config error interrupt */
case SPI_INT_FLAG_CONFERR:
reg1 = reg1 & SPI_STAT_CONFERR;
reg2 = reg2 & SPI_CTL1_ERRIE;
break;
/* SPI CRC error interrupt */
case SPI_INT_FLAG_CRCERR:
reg1 = reg1 & SPI_STAT_CRCERR;
reg2 = reg2 & SPI_CTL1_ERRIE;
break;
/* I2S underrun error interrupt */
case I2S_INT_FLAG_TXURERR:
reg1 = reg1 & SPI_STAT_TXURERR;
reg2 = reg2 & SPI_CTL1_ERRIE;
break;
/* SPI/I2S format error interrupt */
case SPI_I2S_INT_FLAG_FERR:
reg1 = reg1 & SPI_STAT_FERR;
reg2 = reg2 & SPI_CTL1_ERRIE;
break;
default :
break;
}
/*get SPI/I2S interrupt flag status */
if((0U != reg1) && (0U != reg2)){
return SET;
}else{
return RESET;
}
}
/*!
\brief get SPI and I2S flag status
\param[in] spi_periph: SPIx(x=0,1)
\param[in] flag: SPI/I2S flag status
one or more parameters can be selected which are shown as below:
\arg SPI_FLAG_TBE: transmit buffer empty flag
\arg SPI_FLAG_RBNE: receive buffer not empty flag
\arg SPI_FLAG_TRANS: transmit on-going flag
\arg SPI_FLAG_RXORERR: receive overrun error flag
\arg SPI_FLAG_CONFERR: mode config error flag
\arg SPI_FLAG_CRCERR: CRC error flag
\arg SPI_FLAG_FERR: format error interrupt flag
\arg I2S_FLAG_TBE: transmit buffer empty flag
\arg I2S_FLAG_RBNE: receive buffer not empty flag
\arg I2S_FLAG_TRANS: transmit on-going flag
\arg I2S_FLAG_RXORERR: overrun error flag
\arg I2S_FLAG_TXURERR: underrun error flag
\arg I2S_FLAG_CH: channel side flag
\arg I2S_FLAG_FERR: format error interrupt flag
\param[out] none
\retval FlagStatus: SET or RESET
*/
FlagStatus spi_i2s_flag_get(uint32_t spi_periph, uint32_t flag)
{
if(RESET != (SPI_STAT(spi_periph) & flag)){
return SET;
}else{
return RESET;
}
}
/*!
\brief clear SPI CRC error flag status
\param[in] spi_periph: SPIx(x=0,1)
\param[out] none
\retval none
*/
void spi_crc_error_clear(uint32_t spi_periph)
{
SPI_STAT(spi_periph) &= (uint32_t)(~SPI_FLAG_CRCERR);
}
View Git Blame Copy Permalink