rt-thread/bsp/stm3210/board.c

/*
 * File      : board.c
 * This file is part of RT-Thread RTOS
 * COPYRIGHT (C) 2006 - 2009 RT-Thread Develop Team
 *
 * The license and distribution terms for this file may be
 * found in the file LICENSE in this distribution or at
 * http://www.rt-thread.org/license/LICENSE
 *
 * Change Logs:
 * Date           Author       Notes
 * 2006-08-23     Bernard      first implementation
 */

#include <rthw.h>
#include <rtthread.h>

#include "stm32f10x.h"
#include "board.h"

static void rt_hw_console_init(void);

/**
 * @addtogroup STM32
 */

/*@{*/

/*******************************************************************************
* Function Name  : NVIC_Configuration
* Description    : Configures Vector Table base location.
* Input          : None
* Output         : None
* Return         : None
*******************************************************************************/
void NVIC_Configuration(void)
{
#ifdef  VECT_TAB_RAM
	/* Set the Vector Table base location at 0x20000000 */
	NVIC_SetVectorTable(NVIC_VectTab_RAM, 0x0);
#else  /* VECT_TAB_FLASH  */
	/* Set the Vector Table base location at 0x08000000 */
	NVIC_SetVectorTable(NVIC_VectTab_FLASH, 0x0);
#endif
}

/*******************************************************************************
 * Function Name  : SysTick_Configuration
 * Description    : Configures the SysTick for OS tick.
 * Input          : None
 * Output         : None
 * Return         : None
 *******************************************************************************/
void  SysTick_Configuration(void)
{
    RCC_ClocksTypeDef  rcc_clocks;
    rt_uint32_t         cnts;

    RCC_GetClocksFreq(&rcc_clocks);

    cnts = (rt_uint32_t)rcc_clocks.HCLK_Frequency / RT_TICK_PER_SECOND;

    SysTick_Config(cnts);
    SysTick_CLKSourceConfig(SysTick_CLKSource_HCLK);
}

/**
 * This is the timer interrupt service routine.
 *
 */
void rt_hw_timer_handler(void)
{
	rt_tick_increase();
}

/**
 * This function will initial STM32 board.
 */
void rt_hw_board_init()
{
	/* NVIC Configuration */
	NVIC_Configuration();

	/* Configure the SysTick */
	SysTick_Configuration();

	rt_hw_console_init();
}

/* init console to support rt_kprintf */
static void rt_hw_console_init()
{
	/* Enable USART1 and GPIOA clocks */
	RCC_APB2PeriphClockCmd(RCC_APB2Periph_USART1 | RCC_APB2Periph_GPIOA, ENABLE);

	/* GPIO configuration */
	{
	GPIO_InitTypeDef GPIO_InitStructure;

	/* Configure USART1 Tx (PA.09) as alternate function push-pull */
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_9;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_AF_PP;
	GPIO_InitStructure.GPIO_Speed = GPIO_Speed_50MHz;
	GPIO_Init(GPIOA, &GPIO_InitStructure);

	/* Configure USART1 Rx (PA.10) as input floating */
	GPIO_InitStructure.GPIO_Pin = GPIO_Pin_10;
	GPIO_InitStructure.GPIO_Mode = GPIO_Mode_IN_FLOATING;
	GPIO_Init(GPIOA, &GPIO_InitStructure);
	}

	/* USART configuration */
	{
	USART_InitTypeDef USART_InitStructure;

	/* USART1 configured as follow:
		- BaudRate = 115200 baud
		- Word Length = 8 Bits
		- One Stop Bit
		- No parity
		- Hardware flow control disabled (RTS and CTS signals)
		- Receive and transmit enabled
		- USART Clock disabled
		- USART CPOL: Clock is active low
		- USART CPHA: Data is captured on the middle
		- USART LastBit: The clock pulse of the last data bit is not output to
		  the SCLK pin
	*/
	USART_InitStructure.USART_BaudRate = 115200;
	USART_InitStructure.USART_WordLength = USART_WordLength_8b;
	USART_InitStructure.USART_StopBits = USART_StopBits_1;
	USART_InitStructure.USART_Parity = USART_Parity_No;
	USART_InitStructure.USART_HardwareFlowControl = USART_HardwareFlowControl_None;
	USART_InitStructure.USART_Mode = USART_Mode_Rx | USART_Mode_Tx;
	USART_Init(USART1, &USART_InitStructure);
	/* Enable USART1 */
	USART_Cmd(USART1, ENABLE);
	}
}

/* write one character to serial, must not trigger interrupt */
static void rt_hw_console_putc(const char c)
{
	/*
		to be polite with serial console add a line feed
		to the carriage return character
	*/
	if (c=='\n')rt_hw_console_putc('\r');

	while (!(USART1->SR & USART_FLAG_TXE));
	USART1->DR = (c & 0x1FF);
}

/**
 * This function is used by rt_kprintf to display a string on console.
 *
 * @param str the displayed string
 */
void rt_hw_console_output(const char* str)
{
	while (*str)
	{
		rt_hw_console_putc (*str++);
	}
}

/*@}*/