menu "Hardware Drivers Config" config SOC_STM32F429IG bool select SOC_SERIES_STM32F4 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" config BSP_USING_USB_TO_USART bool "Enable USB TO USART (uart1)" select BSP_USING_UART select BSP_USING_UART1 default y config BSP_USING_COM2 bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)" select BSP_USING_UART select BSP_USING_UART2 default n config BSP_USING_COM3 bool "Enable COM3 (uart3 pin conflict with Ethernet)" select BSP_USING_UART3 default n config BSP_USING_SDRAM bool "Enable SDRAM" select BSP_USING_FMC default n config BSP_USING_SPI_FLASH bool "Enable SPI FLASH (W25Q256 spi5)" select BSP_USING_SPI select BSP_USING_SPI5 select RT_USING_SFUD select RT_SFUD_USING_SFDP default n config BSP_USING_MPU9250 bool "Enable MPU 9250 (i2c1)" select BSP_USING_I2C1 select PKG_USING_MPU6XXX default n config PHY_USING_LAN8720A bool config BSP_USING_ETH bool "Enable Ethernet" select BSP_USING_I2C1 select PKG_USING_PCF8574 select RT_USING_LWIP select PHY_USING_LAN8720A default n config BSP_USING_SDCARD bool "Enable SDCARD (sdio)" select BSP_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT default n config BSP_USING_AUDIO bool "Enable AUDIO (WM8978)" select BSP_USING_I2C1 select RT_USING_AUDIO default n if BSP_USING_AUDIO config BSP_USING_AUDIO_PLAY bool "Enable Audio Play" default y config BSP_USING_AUDIO_RECORD bool "Enable Audio Record" select BSP_USING_AUDIO_PLAY default n endif endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default y config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_USING_UART2 bool "Enable UART2" default n config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_USING_UART3 bool "Enable UART3" default n config BSP_UART3_RX_USING_DMA bool "Enable UART3 RX DMA" depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA default n endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n menuconfig BSP_USING_CAN bool "Enable CAN" default n select RT_USING_CAN if BSP_USING_CAN config BSP_USING_CAN1 bool "Enable CAN1" default n endif menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 BUS" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI2 bool "Enable SPI2 BUS" default n config BSP_SPI2_TX_USING_DMA bool "Enable SPI2 TX DMA" depends on BSP_USING_SPI2 default n config BSP_SPI2_RX_USING_DMA bool "Enable SPI2 RX DMA" depends on BSP_USING_SPI2 select BSP_SPI2_TX_USING_DMA default n config BSP_USING_SPI5 bool "Enable SPI5 BUS" default n config BSP_SPI5_TX_USING_DMA bool "Enable SPI5 TX DMA" depends on BSP_USING_SPI5 default n config BSP_SPI5_RX_USING_DMA bool "Enable SPI5 RX DMA" depends on BSP_USING_SPI5 select BSP_SPI5_TX_USING_DMA default n endif menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 comment "Notice: PH4 --> 116; PH5 --> 117" config BSP_I2C1_SCL_PIN int "I2C1 scl pin number" range 1 176 default 116 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 1 176 default 117 endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM11 bool "Enable TIM11" default n config BSP_USING_TIM13 bool "Enable TIM13" default n config BSP_USING_TIM14 bool "Enable TIM14" default n endif menuconfig BSP_USING_PWM bool "Enable pwm" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM2 bool "Enable timer2 output pwm" default n if BSP_USING_PWM2 config BSP_USING_PWM2_CH4 bool "Enable PWM2 channel4" default n endif endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC select RT_USING_LIBC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n menuconfig BSP_USING_USBH bool "Enable USB Host" select RT_USING_USB_HOST default n if BSP_USING_USBH menuconfig RT_USBH_MSTORAGE bool "Enable Udisk Drivers" default n if RT_USBH_MSTORAGE config UDISK_MOUNTPOINT string "Udisk mount dir" default "/" endif endif config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n config BSP_USING_FMC bool default n source "../libraries/HAL_Drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu