menu "Hardware Drivers Config" config SOC_STM32H750XB bool select SOC_SERIES_STM32H7 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" config BSP_USING_USB_TO_USART bool "Enable Debuger USART (uart4)" select BSP_USING_UART select BSP_USING_UART4 default n config BSP_USING_SPI_FLASH bool "Enable SPI FLASH (spi1)" select BSP_USING_SPI select BSP_USING_SPI1 select PKG_USING_FAL select FAL_USING_SFUD_PORT select RT_USING_SFUD default n config BSP_USING_QSPI_FLASH bool "Enable QSPI FLASH (w25q64 qspi)" select BSP_USING_QSPI select FAL_USING_SFUD_PORT select RT_USING_SFUD select RT_SFUD_USING_QSPI default n config BSP_USING_WIFI bool "Enable wifi (AP6212)" select ART_PI_USING_WIFI_6212_LIB select ART_PI_USING_OTA_LIB select BSP_USING_SPI_FLASH select RT_USING_WIFI select RT_USING_SAL default n config BSP_USING_OV2640 bool "Enable camera (ov2640)" select BSP_USING_DCMI select BSP_USING_I2C select BSP_USING_I2C2 default n config BSP_USING_GC0328C bool "Enable camera (gc0328)" select BSP_USING_DCMI select BSP_USING_I2C select BSP_USING_I2C2 default n menuconfig BSP_USING_FS bool "Enable filesystem" select RT_USING_DFS select RT_USING_DFS_ROMFS default n if BSP_USING_FS config BSP_USING_SDCARD_FS bool "Enable SDCARD filesystem" select BSP_USING_SDIO select BSP_USING_SDIO1 select RT_USING_DFS_ELMFAT default n config BSP_USING_SPI_FLASH_FS bool "Enable SPI FLASH filesystem" select BSP_USING_SPI_FLASH select RT_USING_MTD_NOR select PKG_USING_LITTLEFS default n endif endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default n select RT_USING_SERIAL select RT_SERIAL_USING_DMA if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default n config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_UART1_TX_USING_DMA bool "Enable UART1 TX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_USING_UART3 bool "Enable UART3" default n config BSP_USING_UART4 bool "Enable UART4" default n config BSP_USING_UART6 bool "Enable UART6" default n endif menuconfig BSP_USING_SPI bool "Enable SPI" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1" default n config BSP_USING_SPI2 bool "Enable SPI2" default n config BSP_USING_SPI4 bool "Enable SPI4" default n endif config BSP_USING_QSPI bool "Enable QSPI BUS" select RT_USING_QSPI select RT_USING_SPI default n menuconfig BSP_USING_I2C bool "Enable I2C BUS (software simulation)" select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN default n if BSP_USING_I2C menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 comment "Notice: PB6 --> 22; PB7 --> 23" config BSP_I2C1_SCL_PIN int "I2C1 scl pin number" range 0 175 default 22 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 0 175 default 23 endif menuconfig BSP_USING_I2C2 bool "Enable I2C2 BUS (software simulation)" default n if BSP_USING_I2C2 comment "Notice: PH13 --> 125; PH15 --> 127" config BSP_I2C2_SCL_PIN int "i2c2 scl pin number" range 1 176 default 127 config BSP_I2C2_SDA_PIN int "I2C2 sda pin number" range 0 175 default 125 endif menuconfig BSP_USING_I2C3 bool "Enable I2C3 BUS (software simulation)" default n if BSP_USING_I2C3 comment "Notice: PH12 --> 124; PH11 --> 123" config BSP_I2C3_SCL_PIN int "i2c3 scl pin number" range 0 175 default 123 config BSP_I2C3_SDA_PIN int "I2C3 sda pin number" range 0 175 default 124 endif endif menuconfig BSP_USING_SDIO bool "Enable SDIO" default n select RT_USING_SDIO if BSP_USING_SDIO config BSP_USING_SDIO1 bool "Enable SDIO1" default n config BSP_USING_SDIO2 bool "Enable SDIO2" default n endif config BSP_USING_SDRAM bool "Enable SDRAM" default n menuconfig BSP_USING_ETH bool "Enable Ethernet" default n select RT_USING_LWIP if BSP_USING_ETH config ETH_RESET_PIN string "ETH RESET PIN" default "PA.3" endif if BSP_USING_ETH choice prompt "Choose ETH PHY" default PHY_USING_LAN8720A config PHY_USING_LAN8720A bool "USING LAN8720A" default n endchoice endif config BSP_USING_LCD bool "Enable LCD" select BSP_USING_GPIO select BSP_USING_SDRAM select RT_USING_MEMHEAP default n config BSP_USING_DCMI bool "Enable DCMI" default n menuconfig BSP_USING_FDCAN bool "Enable FDCAN" default n select RT_USING_CAN if BSP_USING_FDCAN config BSP_USING_FDCAN1 bool "USING FDCAN1" default n endif config BSP_USING_USBD bool "Enable USB Device" select RT_USING_USB_DEVICE default n menuconfig BSP_USING_USBH bool "Enable USB Host" select RT_USING_USB_HOST default n if BSP_USING_USBH menuconfig RT_USBH_MSTORAGE bool "Enable Udisk Drivers" select RT_USING_DFS select RT_USING_DFS_ELMFAT default n if RT_USBH_MSTORAGE config UDISK_MOUNTPOINT string "Udisk mount dir" default "/" endif endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM13 bool "Enable TIM13" default n endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM5 bool "Enable Timer5 output pwm" default n if BSP_USING_PWM5 config BSP_USING_PWM5_CH1 bool "Enable PWM5 channel1" default n endif config SAMPLES_USING_PWM bool "SAMPLE PWM5 channel1" default n endif config BSP_USING_ONCHIP_RTC bool "Enable Onchip RTC" select RT_USING_RTC default n source "../libraries/HAL_Drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu