menu "Hardware Drivers Config"

config SOC_STM32F103ZE
    bool
    select SOC_SERIES_STM32F1
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        select RT_USING_PIN
        default n
        
    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q64 spi2)"
        select BSP_USING_SPI
        select BSP_USING_SPI2
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n
        
    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c2)"
        select BSP_USING_I2C2
        default n
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

        endif
        
    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
                
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n  
                
            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n
                
            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
                
            config BSP_USING_SPI3
                bool "Enable SPI3 BUS"
                default n        

            config BSP_SPI3_TX_USING_DMA
                bool "Enable SPI3 TX DMA"
                depends on BSP_USING_SPI3
                default n
                
            config BSP_SPI3_RX_USING_DMA
                bool "Enable SPI3 RX DMA"
                depends on BSP_USING_SPI3
                select BSP_SPI3_TX_USING_DMA
                default n  
        endif
        
    menuconfig BSP_USING_I2C2
        bool "Enable I2C2 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C2
            comment "Notice: PB10 --> 26; PB11 --> 27" 
            config BSP_I2C2_SCL_PIN
                int "i2c2 scl pin number"
                range 0 175
                default 26
            config BSP_I2C2_SDA_PIN
                int "i2c2 sda pin number"
                range 0 175
                default 27
        endif
        
    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n
        
    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

endmenu

menu "Board extended module Drivers"

endmenu

endmenu