menu "Hardware Drivers Config" menu "On-chip Peripheral Drivers" source "$(BSP_DIR)/../libraries/nuc980/rtt_port/Kconfig" endmenu menu "On-board Peripheral Drivers" config BSP_USING_CONSOLE bool "Enable UART0 for RTT Console(uart0)" select BSP_USING_UART select BSP_USING_UART0 default y config BOARD_USING_IP101GR bool "Enable ethernet phy supporting(over emac/mdio)" select BSP_USING_EMAC default n config BOARD_USING_NAU8822 bool "NAU8822 Audio Codec supporting(over i2s, i2c0)" select NU_PKG_USING_NAU8822 select BSP_USING_I2C0 select BSP_USING_I2S select BSP_USING_I2S0 default n config BOARD_USING_STORAGE_SDCARD bool "SDCARD supporting(over sdh1)" select BSP_USING_SDH select BSP_USING_SDH1 default y config BOARD_USING_STORAGE_SPIFLASH bool "SPI NOR FLASH supporting(over qspi0)" select BSP_USING_QSPI select BSP_USING_QSPI0 default n config BOARD_USING_STORAGE_SPINAND bool "SPI NAND FLASH supporting(over qspi0)" select BSP_USING_QSPI select BSP_USING_QSPI0 select NU_PKG_USING_SPINAND default y config BOARD_USING_USB0_DEVICE_HOST select BSP_USING_USBH select BSP_USING_USBD bool "Enable USB0 Device/Host" help Choose this option if you need USB device or host function mode. If you need USB host, please remember short to ground on JP1 jumper. config BOARD_USING_USB1_HOST select BSP_USING_USBH bool "Enable USB1 Host" help Choose this option if you need USB1 HOST. endmenu menu "Board extended module drivers" config BOARD_USING_MAX31875 bool "MAX31875 Temperature sensor(over i2c1)" select NU_PKG_USING_MAX31875 select BSP_USING_I2C1 default n config BOARD_USING_LCD_ILI9341 bool "LCD ILI9341 (over spi0)" select RT_USING_TOUCH select BSP_USING_ADC_TOUCH select NU_PKG_USING_ADC_TOUCH select NU_PKG_USING_ILI9341 select NU_PKG_USING_ILI9341_SPI select NU_PKG_ILI9341_WITH_OFFSCREEN_FRAMEBUFFER select NU_PKG_ILI9341_HORIZONTAL select BSP_USING_SPI0 default n if BOARD_USING_LCD_ILI9341 config BOARD_USING_ILI9341_PIN_BACKLIGHT int "Specify the pin index of backlight pin index" range 0 127 default 103 config BOARD_USING_ILI9341_PIN_RESET int "Specify the pin index of reset pin index" range 0 127 default 90 config BOARD_USING_ILI9341_PIN_DC int "Specify the pin index of data&command switching" range 0 127 default 89 endif config BOARD_USING_ESP8266 bool "ESP8266 Wi-Fi module supporting(over uart1)" select BSP_USING_UART select BSP_USING_UART1 select BSP_USING_UART1_RX_DMA select BSP_USING_UART1_TX_DMA select PKG_USING_AT_DEVICE select AT_DEVICE_USING_ESP8266 select AT_DEVICE_ESP8266_INIT_ASYN default n endmenu source "$(BSP_DIR)/../libraries/nu_packages/Kconfig" endmenu