menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_STLINK_TO_USART
        bool "Enable STLINK TO USART (lpuart1)"
        select BSP_USING_UART
        select BSP_USING_LPUART1
        default y

    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default y
            config BSP_LPUART1_RX_USING_DMA
                bool "Enable LPUART1 RX DMA"
                depends on BSP_USING_LPUART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default n
            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n
            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        select RT_USING_FAL
        default n

    config BSP_USING_ON_CHIP_FLASH_FATFS
        bool "Enable onchip flash with FatFS"
        depends on BSP_USING_ON_CHIP_FLASH
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n
            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n
            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n
            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C BUS"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C
            menuconfig BSP_USING_I2C2
                bool "Enable I2C2 BUS (software simulation)"
                default n
                if BSP_USING_I2C2
                    config BSP_I2C2_SCL_PIN
                        int "i2c2 scl pin number"
                        range 1 176
                        default 29
                    config BSP_I2C2_SDA_PIN
                        int "I2C2 sda pin number"
                        range 1 176
                        default 30
                endif

            menuconfig BSP_USING_I2C3
                bool "Enable I2C3 BUS (software simulation)"
                default n
                if BSP_USING_I2C3
                    config BSP_I2C3_SCL_PIN
                        int "i2c3 scl pin number"
                        range 1 176
                        default 32
                    config BSP_I2C3_SDA_PIN
                        int "I2C3 sda pin number"
                        range 1 176
                        default 33
                endif

            menuconfig BSP_USING_I2C4
                bool "Enable I2C4 BUS (software simulation)"
                default y
                if BSP_USING_I2C4
                    config BSP_I2C4_SCL_PIN
                        int "i2c4 scl pin number"
                        range 1 176
                        default 60
                    config BSP_I2C4_SDA_PIN
                        int "i2c4 sda pin number"
                        range 1 176
                        default 61
                endif
        endif

    config BSP_USING_SDIO
        bool "Enable sdio"
        select RT_USING_SDIO
        default n

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM15
                bool "Enable TIM15"
                default n

            config BSP_USING_TIM16
                bool "Enable TIM16"
                default n

            config BSP_USING_TIM17
                bool "Enable TIM17"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM3
            bool "Enable timer3 output PWM"
            default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH2
                    bool "Enable PWM3 channel2"
                    default n

                config BSP_USING_PWM3_CH3
                    bool "Enable PWM3 channel3"
                    default n

                config BSP_USING_PWM3_CH4
                    bool "Enable PWM3 channel4"
                    default n
            endif
        endif

    config BSP_USING_ADC1
        bool "Enable ADC1"
        default n
        select RT_USING_ADC

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

 source "$(BSP_DIR)/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu