//*****************************************************************************
//
// hw_can.h - Defines and macros used when accessing the CAN controllers.
//
// Copyright (c) 2006-2017 Texas Instruments Incorporated.  All rights reserved.
// Software License Agreement
//
//   Redistribution and use in source and binary forms, with or without
//   modification, are permitted provided that the following conditions
//   are met:
//
//   Redistributions of source code must retain the above copyright
//   notice, this list of conditions and the following disclaimer.
//
//   Redistributions in binary form must reproduce the above copyright
//   notice, this list of conditions and the following disclaimer in the
//   documentation and/or other materials provided with the
//   distribution.
//
//   Neither the name of Texas Instruments Incorporated nor the names of
//   its contributors may be used to endorse or promote products derived
//   from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
//
//*****************************************************************************

#ifndef __HW_CAN_H__
#define __HW_CAN_H__

//*****************************************************************************
//
// The following are defines for the CAN register offsets.
//
//*****************************************************************************
#define CAN_O_CTL               0x00000000  // CAN Control
#define CAN_O_STS               0x00000004  // CAN Status
#define CAN_O_ERR               0x00000008  // CAN Error Counter
#define CAN_O_BIT               0x0000000C  // CAN Bit Timing
#define CAN_O_INT               0x00000010  // CAN Interrupt
#define CAN_O_TST               0x00000014  // CAN Test
#define CAN_O_BRPE              0x00000018  // CAN Baud Rate Prescaler
                                            // Extension
#define CAN_O_IF1CRQ            0x00000020  // CAN IF1 Command Request
#define CAN_O_IF1CMSK           0x00000024  // CAN IF1 Command Mask
#define CAN_O_IF1MSK1           0x00000028  // CAN IF1 Mask 1
#define CAN_O_IF1MSK2           0x0000002C  // CAN IF1 Mask 2
#define CAN_O_IF1ARB1           0x00000030  // CAN IF1 Arbitration 1
#define CAN_O_IF1ARB2           0x00000034  // CAN IF1 Arbitration 2
#define CAN_O_IF1MCTL           0x00000038  // CAN IF1 Message Control
#define CAN_O_IF1DA1            0x0000003C  // CAN IF1 Data A1
#define CAN_O_IF1DA2            0x00000040  // CAN IF1 Data A2
#define CAN_O_IF1DB1            0x00000044  // CAN IF1 Data B1
#define CAN_O_IF1DB2            0x00000048  // CAN IF1 Data B2
#define CAN_O_IF2CRQ            0x00000080  // CAN IF2 Command Request
#define CAN_O_IF2CMSK           0x00000084  // CAN IF2 Command Mask
#define CAN_O_IF2MSK1           0x00000088  // CAN IF2 Mask 1
#define CAN_O_IF2MSK2           0x0000008C  // CAN IF2 Mask 2
#define CAN_O_IF2ARB1           0x00000090  // CAN IF2 Arbitration 1
#define CAN_O_IF2ARB2           0x00000094  // CAN IF2 Arbitration 2
#define CAN_O_IF2MCTL           0x00000098  // CAN IF2 Message Control
#define CAN_O_IF2DA1            0x0000009C  // CAN IF2 Data A1
#define CAN_O_IF2DA2            0x000000A0  // CAN IF2 Data A2
#define CAN_O_IF2DB1            0x000000A4  // CAN IF2 Data B1
#define CAN_O_IF2DB2            0x000000A8  // CAN IF2 Data B2
#define CAN_O_TXRQ1             0x00000100  // CAN Transmission Request 1
#define CAN_O_TXRQ2             0x00000104  // CAN Transmission Request 2
#define CAN_O_NWDA1             0x00000120  // CAN New Data 1
#define CAN_O_NWDA2             0x00000124  // CAN New Data 2
#define CAN_O_MSG1INT           0x00000140  // CAN Message 1 Interrupt Pending
#define CAN_O_MSG2INT           0x00000144  // CAN Message 2 Interrupt Pending
#define CAN_O_MSG1VAL           0x00000160  // CAN Message 1 Valid
#define CAN_O_MSG2VAL           0x00000164  // CAN Message 2 Valid

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_CTL register.
//
//*****************************************************************************
#define CAN_CTL_TEST            0x00000080  // Test Mode Enable
#define CAN_CTL_CCE             0x00000040  // Configuration Change Enable
#define CAN_CTL_DAR             0x00000020  // Disable Automatic-Retransmission
#define CAN_CTL_EIE             0x00000008  // Error Interrupt Enable
#define CAN_CTL_SIE             0x00000004  // Status Interrupt Enable
#define CAN_CTL_IE              0x00000002  // CAN Interrupt Enable
#define CAN_CTL_INIT            0x00000001  // Initialization

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_STS register.
//
//*****************************************************************************
#define CAN_STS_BOFF            0x00000080  // Bus-Off Status
#define CAN_STS_EWARN           0x00000040  // Warning Status
#define CAN_STS_EPASS           0x00000020  // Error Passive
#define CAN_STS_RXOK            0x00000010  // Received a Message Successfully
#define CAN_STS_TXOK            0x00000008  // Transmitted a Message
                                            // Successfully
#define CAN_STS_LEC_M           0x00000007  // Last Error Code
#define CAN_STS_LEC_NONE        0x00000000  // No Error
#define CAN_STS_LEC_STUFF       0x00000001  // Stuff Error
#define CAN_STS_LEC_FORM        0x00000002  // Format Error
#define CAN_STS_LEC_ACK         0x00000003  // ACK Error
#define CAN_STS_LEC_BIT1        0x00000004  // Bit 1 Error
#define CAN_STS_LEC_BIT0        0x00000005  // Bit 0 Error
#define CAN_STS_LEC_CRC         0x00000006  // CRC Error
#define CAN_STS_LEC_NOEVENT     0x00000007  // No Event

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_ERR register.
//
//*****************************************************************************
#define CAN_ERR_RP              0x00008000  // Received Error Passive
#define CAN_ERR_REC_M           0x00007F00  // Receive Error Counter
#define CAN_ERR_TEC_M           0x000000FF  // Transmit Error Counter
#define CAN_ERR_REC_S           8
#define CAN_ERR_TEC_S           0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_BIT register.
//
//*****************************************************************************
#define CAN_BIT_TSEG2_M         0x00007000  // Time Segment after Sample Point
#define CAN_BIT_TSEG1_M         0x00000F00  // Time Segment Before Sample Point
#define CAN_BIT_SJW_M           0x000000C0  // (Re)Synchronization Jump Width
#define CAN_BIT_BRP_M           0x0000003F  // Baud Rate Prescaler
#define CAN_BIT_TSEG2_S         12
#define CAN_BIT_TSEG1_S         8
#define CAN_BIT_SJW_S           6
#define CAN_BIT_BRP_S           0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_INT register.
//
//*****************************************************************************
#define CAN_INT_INTID_M         0x0000FFFF  // Interrupt Identifier
#define CAN_INT_INTID_NONE      0x00000000  // No interrupt pending
#define CAN_INT_INTID_STATUS    0x00008000  // Status Interrupt

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_TST register.
//
//*****************************************************************************
#define CAN_TST_RX              0x00000080  // Receive Observation
#define CAN_TST_TX_M            0x00000060  // Transmit Control
#define CAN_TST_TX_CANCTL       0x00000000  // CAN Module Control
#define CAN_TST_TX_SAMPLE       0x00000020  // Sample Point
#define CAN_TST_TX_DOMINANT     0x00000040  // Driven Low
#define CAN_TST_TX_RECESSIVE    0x00000060  // Driven High
#define CAN_TST_LBACK           0x00000010  // Loopback Mode
#define CAN_TST_SILENT          0x00000008  // Silent Mode
#define CAN_TST_BASIC           0x00000004  // Basic Mode

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_BRPE register.
//
//*****************************************************************************
#define CAN_BRPE_BRPE_M         0x0000000F  // Baud Rate Prescaler Extension
#define CAN_BRPE_BRPE_S         0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1CRQ register.
//
//*****************************************************************************
#define CAN_IF1CRQ_BUSY         0x00008000  // Busy Flag
#define CAN_IF1CRQ_MNUM_M       0x0000003F  // Message Number
#define CAN_IF1CRQ_MNUM_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1CMSK register.
//
//*****************************************************************************
#define CAN_IF1CMSK_WRNRD       0x00000080  // Write, Not Read
#define CAN_IF1CMSK_MASK        0x00000040  // Access Mask Bits
#define CAN_IF1CMSK_ARB         0x00000020  // Access Arbitration Bits
#define CAN_IF1CMSK_CONTROL     0x00000010  // Access Control Bits
#define CAN_IF1CMSK_CLRINTPND   0x00000008  // Clear Interrupt Pending Bit
#define CAN_IF1CMSK_NEWDAT      0x00000004  // Access New Data
#define CAN_IF1CMSK_TXRQST      0x00000004  // Access Transmission Request
#define CAN_IF1CMSK_DATAA       0x00000002  // Access Data Byte 0 to 3
#define CAN_IF1CMSK_DATAB       0x00000001  // Access Data Byte 4 to 7

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1MSK1 register.
//
//*****************************************************************************
#define CAN_IF1MSK1_IDMSK_M     0x0000FFFF  // Identifier Mask
#define CAN_IF1MSK1_IDMSK_S     0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1MSK2 register.
//
//*****************************************************************************
#define CAN_IF1MSK2_MXTD        0x00008000  // Mask Extended Identifier
#define CAN_IF1MSK2_MDIR        0x00004000  // Mask Message Direction
#define CAN_IF1MSK2_IDMSK_M     0x00001FFF  // Identifier Mask
#define CAN_IF1MSK2_IDMSK_S     0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1ARB1 register.
//
//*****************************************************************************
#define CAN_IF1ARB1_ID_M        0x0000FFFF  // Message Identifier
#define CAN_IF1ARB1_ID_S        0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1ARB2 register.
//
//*****************************************************************************
#define CAN_IF1ARB2_MSGVAL      0x00008000  // Message Valid
#define CAN_IF1ARB2_XTD         0x00004000  // Extended Identifier
#define CAN_IF1ARB2_DIR         0x00002000  // Message Direction
#define CAN_IF1ARB2_ID_M        0x00001FFF  // Message Identifier
#define CAN_IF1ARB2_ID_S        0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1MCTL register.
//
//*****************************************************************************
#define CAN_IF1MCTL_NEWDAT      0x00008000  // New Data
#define CAN_IF1MCTL_MSGLST      0x00004000  // Message Lost
#define CAN_IF1MCTL_INTPND      0x00002000  // Interrupt Pending
#define CAN_IF1MCTL_UMASK       0x00001000  // Use Acceptance Mask
#define CAN_IF1MCTL_TXIE        0x00000800  // Transmit Interrupt Enable
#define CAN_IF1MCTL_RXIE        0x00000400  // Receive Interrupt Enable
#define CAN_IF1MCTL_RMTEN       0x00000200  // Remote Enable
#define CAN_IF1MCTL_TXRQST      0x00000100  // Transmit Request
#define CAN_IF1MCTL_EOB         0x00000080  // End of Buffer
#define CAN_IF1MCTL_DLC_M       0x0000000F  // Data Length Code
#define CAN_IF1MCTL_DLC_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1DA1 register.
//
//*****************************************************************************
#define CAN_IF1DA1_DATA_M       0x0000FFFF  // Data
#define CAN_IF1DA1_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1DA2 register.
//
//*****************************************************************************
#define CAN_IF1DA2_DATA_M       0x0000FFFF  // Data
#define CAN_IF1DA2_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1DB1 register.
//
//*****************************************************************************
#define CAN_IF1DB1_DATA_M       0x0000FFFF  // Data
#define CAN_IF1DB1_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF1DB2 register.
//
//*****************************************************************************
#define CAN_IF1DB2_DATA_M       0x0000FFFF  // Data
#define CAN_IF1DB2_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2CRQ register.
//
//*****************************************************************************
#define CAN_IF2CRQ_BUSY         0x00008000  // Busy Flag
#define CAN_IF2CRQ_MNUM_M       0x0000003F  // Message Number
#define CAN_IF2CRQ_MNUM_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2CMSK register.
//
//*****************************************************************************
#define CAN_IF2CMSK_WRNRD       0x00000080  // Write, Not Read
#define CAN_IF2CMSK_MASK        0x00000040  // Access Mask Bits
#define CAN_IF2CMSK_ARB         0x00000020  // Access Arbitration Bits
#define CAN_IF2CMSK_CONTROL     0x00000010  // Access Control Bits
#define CAN_IF2CMSK_CLRINTPND   0x00000008  // Clear Interrupt Pending Bit
#define CAN_IF2CMSK_NEWDAT      0x00000004  // Access New Data
#define CAN_IF2CMSK_TXRQST      0x00000004  // Access Transmission Request
#define CAN_IF2CMSK_DATAA       0x00000002  // Access Data Byte 0 to 3
#define CAN_IF2CMSK_DATAB       0x00000001  // Access Data Byte 4 to 7

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2MSK1 register.
//
//*****************************************************************************
#define CAN_IF2MSK1_IDMSK_M     0x0000FFFF  // Identifier Mask
#define CAN_IF2MSK1_IDMSK_S     0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2MSK2 register.
//
//*****************************************************************************
#define CAN_IF2MSK2_MXTD        0x00008000  // Mask Extended Identifier
#define CAN_IF2MSK2_MDIR        0x00004000  // Mask Message Direction
#define CAN_IF2MSK2_IDMSK_M     0x00001FFF  // Identifier Mask
#define CAN_IF2MSK2_IDMSK_S     0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2ARB1 register.
//
//*****************************************************************************
#define CAN_IF2ARB1_ID_M        0x0000FFFF  // Message Identifier
#define CAN_IF2ARB1_ID_S        0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2ARB2 register.
//
//*****************************************************************************
#define CAN_IF2ARB2_MSGVAL      0x00008000  // Message Valid
#define CAN_IF2ARB2_XTD         0x00004000  // Extended Identifier
#define CAN_IF2ARB2_DIR         0x00002000  // Message Direction
#define CAN_IF2ARB2_ID_M        0x00001FFF  // Message Identifier
#define CAN_IF2ARB2_ID_S        0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2MCTL register.
//
//*****************************************************************************
#define CAN_IF2MCTL_NEWDAT      0x00008000  // New Data
#define CAN_IF2MCTL_MSGLST      0x00004000  // Message Lost
#define CAN_IF2MCTL_INTPND      0x00002000  // Interrupt Pending
#define CAN_IF2MCTL_UMASK       0x00001000  // Use Acceptance Mask
#define CAN_IF2MCTL_TXIE        0x00000800  // Transmit Interrupt Enable
#define CAN_IF2MCTL_RXIE        0x00000400  // Receive Interrupt Enable
#define CAN_IF2MCTL_RMTEN       0x00000200  // Remote Enable
#define CAN_IF2MCTL_TXRQST      0x00000100  // Transmit Request
#define CAN_IF2MCTL_EOB         0x00000080  // End of Buffer
#define CAN_IF2MCTL_DLC_M       0x0000000F  // Data Length Code
#define CAN_IF2MCTL_DLC_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2DA1 register.
//
//*****************************************************************************
#define CAN_IF2DA1_DATA_M       0x0000FFFF  // Data
#define CAN_IF2DA1_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2DA2 register.
//
//*****************************************************************************
#define CAN_IF2DA2_DATA_M       0x0000FFFF  // Data
#define CAN_IF2DA2_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2DB1 register.
//
//*****************************************************************************
#define CAN_IF2DB1_DATA_M       0x0000FFFF  // Data
#define CAN_IF2DB1_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_IF2DB2 register.
//
//*****************************************************************************
#define CAN_IF2DB2_DATA_M       0x0000FFFF  // Data
#define CAN_IF2DB2_DATA_S       0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_TXRQ1 register.
//
//*****************************************************************************
#define CAN_TXRQ1_TXRQST_M      0x0000FFFF  // Transmission Request Bits
#define CAN_TXRQ1_TXRQST_S      0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_TXRQ2 register.
//
//*****************************************************************************
#define CAN_TXRQ2_TXRQST_M      0x0000FFFF  // Transmission Request Bits
#define CAN_TXRQ2_TXRQST_S      0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_NWDA1 register.
//
//*****************************************************************************
#define CAN_NWDA1_NEWDAT_M      0x0000FFFF  // New Data Bits
#define CAN_NWDA1_NEWDAT_S      0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_NWDA2 register.
//
//*****************************************************************************
#define CAN_NWDA2_NEWDAT_M      0x0000FFFF  // New Data Bits
#define CAN_NWDA2_NEWDAT_S      0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_MSG1INT register.
//
//*****************************************************************************
#define CAN_MSG1INT_INTPND_M    0x0000FFFF  // Interrupt Pending Bits
#define CAN_MSG1INT_INTPND_S    0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_MSG2INT register.
//
//*****************************************************************************
#define CAN_MSG2INT_INTPND_M    0x0000FFFF  // Interrupt Pending Bits
#define CAN_MSG2INT_INTPND_S    0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_MSG1VAL register.
//
//*****************************************************************************
#define CAN_MSG1VAL_MSGVAL_M    0x0000FFFF  // Message Valid Bits
#define CAN_MSG1VAL_MSGVAL_S    0

//*****************************************************************************
//
// The following are defines for the bit fields in the CAN_O_MSG2VAL register.
//
//*****************************************************************************
#define CAN_MSG2VAL_MSGVAL_M    0x0000FFFF  // Message Valid Bits
#define CAN_MSG2VAL_MSGVAL_S    0

#endif // __HW_CAN_H__