//*****************************************************************************
//
//  am_hal_stimer.c
//! @file
//!
//! @brief Functions for interfacing with the system timer (STIMER).
//!
//! @addtogroup stimer2 System Timer (STIMER)
//! @ingroup apollo2hal
//! @{
//
//*****************************************************************************

//*****************************************************************************
//
// Copyright (c) 2017, Ambiq Micro
// All rights reserved.
// 
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions are met:
// 
// 1. Redistributions of source code must retain the above copyright notice,
// this list of conditions and the following disclaimer.
// 
// 2. Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the distribution.
// 
// 3. Neither the name of the copyright holder nor the names of its
// contributors may be used to endorse or promote products derived from this
// software without specific prior written permission.
// 
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS"
// AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE
// IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE
// ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
// LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
// CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
// SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR BUSINESS
// INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY, WHETHER IN
// CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE OR OTHERWISE)
// ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE, EVEN IF ADVISED OF THE
// POSSIBILITY OF SUCH DAMAGE.
//
// This is part of revision 1.2.9 of the AmbiqSuite Development Package.
//
//*****************************************************************************

#include <stdint.h>
#include <stdbool.h>
#include "am_mcu_apollo.h"

//*****************************************************************************
//
//! @brief Set up the stimer.
//!
//! @param ui32STimerConfig is the value to load into the configuration reg.
//!
//! This function should be used to perform the initial set-up of the
//! stimer.
//!
//! @return The 32-bit current config of the STimer Config register
//
//*****************************************************************************
uint32_t
am_hal_stimer_config(uint32_t ui32STimerConfig)
{
    uint32_t ui32CurrVal;

    //
    // Read the current config
    //
    ui32CurrVal = AM_REG(CTIMER, STCFG);

    //
    // Write our configuration value.
    //
    AM_REG(CTIMER, STCFG) = ui32STimerConfig;

    //
    // If all of the clock sources are not HFRC, disable LDO when sleeping if timers are enabled.
    //
    if ( (AM_BFR(CTIMER, STCFG, CLKSEL) == AM_REG_CTIMER_STCFG_CLKSEL_HFRC_DIV16)   ||
         (AM_BFR(CTIMER, STCFG, CLKSEL) == AM_REG_CTIMER_STCFG_CLKSEL_HFRC_DIV256) )
    {
        AM_BFW(PWRCTRL, MISCOPT, DIS_LDOLPMODE_TIMERS, 0);
    }
    else
    {
        AM_BFW(PWRCTRL, MISCOPT, DIS_LDOLPMODE_TIMERS, 1);
    }
    return ui32CurrVal;
}

//*****************************************************************************
//
//! @brief Get the current stimer value.
//!
//! This function can be used to read, uninvasively, the value in the stimer.
//!
//! @return The 32-bit value from the STimer counter register.
//
//*****************************************************************************
uint32_t
am_hal_stimer_counter_get(void)
{
    return AM_REG(CTIMER, STTMR);
}

//*****************************************************************************
//
//! @brief Clear the stimer counter.
//!
//! This function clears the STimer Counter and leaves the stimer running.
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_counter_clear(void)
{
    //
    // Set the clear bit
    //
    AM_REG(CTIMER, STCFG) |= AM_REG_CTIMER_STCFG_CLEAR_M;

    //
    // Reset the clear bit
    //
    AM_REG(CTIMER, STCFG) &= ~AM_REG_CTIMER_STCFG_CLEAR_M;
}

//*****************************************************************************
//
//! @brief Set the compare value.
//!
//! @param ui32CmprInstance is the compare register instance number (0-7).
//! @param ui32Delta is the value to add to the STimer counter and load into
//!        the comparator register.
//!
//! NOTE: There is no way to set an absolute value into a comparator register.
//!       Only deltas added to the STimer counter can be written to the compare
//!       registers.
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_compare_delta_set(uint32_t ui32CmprInstance, uint32_t ui32Delta)
{
    if ( ui32CmprInstance > 7 )
    {
        return;
    }

    AM_REGVAL(AM_REG_STIMER_COMPARE(0, ui32CmprInstance)) = ui32Delta;
}

//*****************************************************************************
//
//! @brief Get the current stimer compare register value.
//!
//! @param ui32CmprInstance is the compare register instance number (0-7).
//!
//! This function can be used to read the value in an stimer compare register.
//!
//!
//! @return None.
//
//*****************************************************************************
uint32_t
am_hal_stimer_compare_get(uint32_t ui32CmprInstance)
{
    if ( ui32CmprInstance > 7 )
    {
        return 0;
    }

    return AM_REGVAL(AM_REG_STIMER_COMPARE(0, ui32CmprInstance));
}

//*****************************************************************************
//
//! @brief Start capturing data with the specified capture register.
//!
//! @param ui32CaptureNum is the Capture Register Number to read (0-3).
//!        ui32GPIONumber is the pin number.
//!        bPolarity: false (0) = Capture on low to high transition.
//!                   true  (1) = Capture on high to low transition.
//!
//! Use this function to start capturing.
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_capture_start(uint32_t ui32CaptureNum,
                            uint32_t ui32GPIONumber,
                            bool bPolarity)
{
    uint32_t ui32CapCtrl;

    if ( ui32GPIONumber > (AM_HAL_GPIO_MAX_PADS-1) )
    {
        return;
    }

    //
    // Set the polarity and pin selection in the GPIO block.
    //
    switch (ui32CaptureNum)
    {
         case 0:
            AM_BFW(GPIO, STMRCAP, STPOL0, bPolarity);
            AM_BFW(GPIO, STMRCAP, STSEL0, ui32GPIONumber);
            ui32CapCtrl = AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_A_M;
            break;
         case 1:
            AM_BFW(GPIO, STMRCAP, STPOL1, bPolarity);
            AM_BFW(GPIO, STMRCAP, STSEL1, ui32GPIONumber);
            ui32CapCtrl = AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_B_M;
            break;
         case 2:
            AM_BFW(GPIO, STMRCAP, STPOL2, bPolarity);
            AM_BFW(GPIO, STMRCAP, STSEL2, ui32GPIONumber);
            ui32CapCtrl = AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_C_M;
            break;
         case 3:
            AM_BFW(GPIO, STMRCAP, STPOL3, bPolarity);
            AM_BFW(GPIO, STMRCAP, STSEL3, ui32GPIONumber);
            ui32CapCtrl = AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_D_M;
            break;
         default:
            return;     // error concealment.
    }

    //
    // Enable it in the CTIMER Block
    //
    AM_REG(CTIMER, CAPTURE_CONTROL) |= ui32CapCtrl;
}

//*****************************************************************************
//
//! @brief Start capturing data with the specified capture register.
//!
//! @param ui32CaptureNum is the Capture Register Number to read.
//!
//! Use this function to start capturing.
//!
//! @return None.
//
//*****************************************************************************
void am_hal_stimer_capture_stop(uint32_t ui32CaptureNum)
{
    //
    // Disable it in the CTIMER block.
    //
    AM_REG(CTIMER, CAPTURE_CONTROL) &=
        ~(AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_A_M <<
            ((AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_B_S -
              AM_REG_CTIMER_CAPTURE_CONTROL_CAPTURE_A_S) * ui32CaptureNum));
}

//*****************************************************************************
//
//! @brief Get the current stimer capture register value.
//!
//! @param ui32CaptureNum is the Capture Register Number to read.
//!
//! This function can be used to read the value in an stimer capture register.
//!
//!
//! @return None.
//
//*****************************************************************************
uint32_t am_hal_stimer_capture_get(uint32_t ui32CaptureNum)
{
    if ( ui32CaptureNum > 7 )
    {
        return 0;
    }

    return AM_REGVAL(AM_REG_STIMER_CAPTURE(0, ui32CaptureNum));
}

//*****************************************************************************
//
//! @brief Enables the selected system timer interrupt.
//!
//! @param ui32Interrupt is the interrupt to be used.
//!
//! This function will enable the selected interrupts in the STIMER interrupt
//! enable register. In order to receive an interrupt from an stimer component,
//! you will need to enable the interrupt for that component in this main
//! register, as well as in the stimer configuration register (accessible though
//! am_hal_stimer_config()), and in the NVIC.
//!
//! ui32Interrupt should be the logical OR of one or more of the following
//! values:
//!
//!     AM_HAL_STIMER_INT_COMPAREA
//!     AM_HAL_STIMER_INT_COMPAREB
//!     AM_HAL_STIMER_INT_COMPAREC
//!     AM_HAL_STIMER_INT_COMPARED
//!     AM_HAL_STIMER_INT_COMPAREE
//!     AM_HAL_STIMER_INT_COMPAREF
//!     AM_HAL_STIMER_INT_COMPAREG
//!     AM_HAL_STIMER_INT_COMPAREH
//!
//!     AM_HAL_STIMER_INT_OVERFLOW
//!
//!     AM_HAL_STIMER_INT_CAPTUREA
//!     AM_HAL_STIMER_INT_CAPTUREB
//!     AM_HAL_STIMER_INT_CAPTUREC
//!     AM_HAL_STIMER_INT_CAPTURED
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_int_enable(uint32_t ui32Interrupt)
{
    //
    // Enable the interrupt at the module level.
    //
    AM_REGn(CTIMER, 0, STMINTEN) |= ui32Interrupt;
}

//*****************************************************************************
//
//! @brief Return the enabled stimer interrupts.
//!
//! This function will return all enabled interrupts in the STIMER
//! interrupt enable register.
//!
//! @return return enabled interrupts. This will be a logical or of:
//!
//!     AM_HAL_STIMER_INT_COMPAREA
//!     AM_HAL_STIMER_INT_COMPAREB
//!     AM_HAL_STIMER_INT_COMPAREC
//!     AM_HAL_STIMER_INT_COMPARED
//!     AM_HAL_STIMER_INT_COMPAREE
//!     AM_HAL_STIMER_INT_COMPAREF
//!     AM_HAL_STIMER_INT_COMPAREG
//!     AM_HAL_STIMER_INT_COMPAREH
//!
//!     AM_HAL_STIMER_INT_OVERFLOW
//!
//!     AM_HAL_STIMER_INT_CAPTUREA
//!     AM_HAL_STIMER_INT_CAPTUREB
//!     AM_HAL_STIMER_INT_CAPTUREC
//!     AM_HAL_STIMER_INT_CAPTURED
//!
//! @return Return the enabled timer interrupts.
//
//*****************************************************************************
uint32_t
am_hal_stimer_int_enable_get(void)
{
    //
    // Return enabled interrupts.
    //
    return AM_REGn(CTIMER, 0, STMINTEN);
}

//*****************************************************************************
//
//! @brief Disables the selected stimer interrupt.
//!
//! @param ui32Interrupt is the interrupt to be used.
//!
//! This function will disable the selected interrupts in the STIMER
//! interrupt register.
//!
//! ui32Interrupt should be the logical OR of one or more of the following
//! values:
//!
//!     AM_HAL_STIMER_INT_COMPAREA
//!     AM_HAL_STIMER_INT_COMPAREB
//!     AM_HAL_STIMER_INT_COMPAREC
//!     AM_HAL_STIMER_INT_COMPARED
//!     AM_HAL_STIMER_INT_COMPAREE
//!     AM_HAL_STIMER_INT_COMPAREF
//!     AM_HAL_STIMER_INT_COMPAREG
//!     AM_HAL_STIMER_INT_COMPAREH
//!
//!     AM_HAL_STIMER_INT_OVERFLOW
//!
//!     AM_HAL_STIMER_INT_CAPTUREA
//!     AM_HAL_STIMER_INT_CAPTUREB
//!     AM_HAL_STIMER_INT_CAPTUREC
//!     AM_HAL_STIMER_INT_CAPTURED
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_int_disable(uint32_t ui32Interrupt)
{
    //
    // Disable the interrupt at the module level.
    //
    AM_REGn(CTIMER, 0, STMINTEN) &= ~ui32Interrupt;
}

//*****************************************************************************
//
//! @brief Sets the selected stimer interrupt.
//!
//! @param ui32Interrupt is the interrupt to be used.
//!
//! This function will set the selected interrupts in the STIMER
//! interrupt register.
//!
//! ui32Interrupt should be the logical OR of one or more of the following
//! values:
//!
//!     AM_HAL_STIMER_INT_COMPAREA
//!     AM_HAL_STIMER_INT_COMPAREB
//!     AM_HAL_STIMER_INT_COMPAREC
//!     AM_HAL_STIMER_INT_COMPARED
//!     AM_HAL_STIMER_INT_COMPAREE
//!     AM_HAL_STIMER_INT_COMPAREF
//!     AM_HAL_STIMER_INT_COMPAREG
//!     AM_HAL_STIMER_INT_COMPAREH
//!
//!     AM_HAL_STIMER_INT_OVERFLOW
//!
//!     AM_HAL_STIMER_INT_CAPTUREA
//!     AM_HAL_STIMER_INT_CAPTUREB
//!     AM_HAL_STIMER_INT_CAPTUREC
//!     AM_HAL_STIMER_INT_CAPTURED
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_int_set(uint32_t ui32Interrupt)
{
    //
    // Set the interrupts.
    //
    AM_REGn(CTIMER, 0, STMINTSET) = ui32Interrupt;
}

//*****************************************************************************
//
//! @brief Clears the selected stimer interrupt.
//!
//! @param ui32Interrupt is the interrupt to be used.
//!
//! This function will clear the selected interrupts in the STIMER
//! interrupt register.
//!
//! ui32Interrupt should be the logical OR of one or more of the following
//! values:
//!
//!     AM_HAL_STIMER_INT_COMPAREA
//!     AM_HAL_STIMER_INT_COMPAREB
//!     AM_HAL_STIMER_INT_COMPAREC
//!     AM_HAL_STIMER_INT_COMPARED
//!     AM_HAL_STIMER_INT_COMPAREE
//!     AM_HAL_STIMER_INT_COMPAREF
//!     AM_HAL_STIMER_INT_COMPAREG
//!     AM_HAL_STIMER_INT_COMPAREH
//!
//!     AM_HAL_STIMER_INT_OVERFLOW
//!
//!     AM_HAL_STIMER_INT_CAPTUREA
//!     AM_HAL_STIMER_INT_CAPTUREB
//!     AM_HAL_STIMER_INT_CAPTUREC
//!     AM_HAL_STIMER_INT_CAPTURED
//!
//! @return None.
//
//*****************************************************************************
void
am_hal_stimer_int_clear(uint32_t ui32Interrupt)
{
    //
    // Disable the interrupt at the module level.
    //
    AM_REGn(CTIMER, 0, STMINTCLR) = ui32Interrupt;
}


//*****************************************************************************
//
//! @brief Returns either the enabled or raw stimer interrupt status.
//!
//! This function will return the stimer interrupt status.
//!
//! @bEnabledOnly if true returns the status of the enabled interrupts
//! only.
//!
//! The return value will be the logical OR of one or more of the following
//! values:
//!
//!
//! @return Returns the stimer interrupt status.
//
//*****************************************************************************
uint32_t
am_hal_stimer_int_status_get(bool bEnabledOnly)
{
    //
    // Return the desired status.
    //
    uint32_t ui32RetVal = AM_REGn(CTIMER, 0, STMINTSTAT);

    if ( bEnabledOnly )
    {
        ui32RetVal &= AM_REGn(CTIMER, 0, STMINTEN);
    }

    return ui32RetVal;
}

//*****************************************************************************
//
// End Doxygen group.
//! @}
//
//*****************************************************************************