/* * Copyright (c) 2006-2022, RT-Thread Development Team * * SPDX-License-Identifier: Apache-2.0 * * Change Logs: * Date Author Notes * 2017-12-30 Sundm75 first version */ #include #include #include #include #include "ls1c.h" #include "ls1c_gpio.h" #include "ls1c_spi.h" #include "drv_spi.h" #include "touch.h" #ifdef XPT2046_USING_TOUCH #include #include #include #include #include //竖屏幕 不需要 _ILI_HORIZONTAL_DIRECTION_ //横屏幕 需要 _ILI_HORIZONTAL_DIRECTION_ //#define _ILI_HORIZONTAL_DIRECTION_ #if defined(_ILI_HORIZONTAL_DIRECTION_) #define X_WIDTH 272 #define Y_WIDTH 480 #else #define X_WIDTH 480 #define Y_WIDTH 272 #endif /* TOUCH INT: 84 */ #define IS_TOUCH_UP() gpio_get(TOUCH_INT_PIN) #define led_gpio 52 // led1指示 #define DUMMY 0x00 /* 7 6 - 4 3 2 1-0 s A2-A0 MODE SER/DFR PD1-PD0 */ /* bit[1:0] power-down */ #define POWER_MODE0 (0) /* Power-Down Between Conversions. When */ /* each conversion is finished, the converter */ /* enters a low-power mode. At the start of the */ /* next conversion, the device instantly powers up */ /* to full power. There is no need for additional */ /* delays to ensure full operation, and the very first */ /* conversion is valid. The Y? switch is on when in */ /* power-down.*/ #define POWER_MODE1 (1) /* Reference is off and ADC is on. */ #define POWER_MODE2 (2) /* Reference is on and ADC is off. */ #define POWER_MODE3 (3) /* Device is always powered. Reference is on and */ /* ADC is on. */ /* bit[2] SER/DFR */ #define DIFFERENTIAL (0<<2) #define SINGLE_ENDED (1<<2) /* bit[3] mode */ #define MODE_12BIT (0<<3) #define MODE_8BIT (1<<3) /* bit[6:4] differential mode */ #define MEASURE_X (((1<<2) | (0<<1) | (1<<0))<<4) #define MEASURE_Y (((0<<2) | (0<<1) | (1<<0))<<4) #define MEASURE_Z1 (((0<<2) | (1<<1) | (1<<0))<<4) #define MEASURE_Z2 (((1<<2) | (0<<1) | (0<<0))<<4) /* bit[7] start */ #define START (1<<7) /* X Y change. */ #define TOUCH_MSR_X (START | MEASURE_X | MODE_12BIT | DIFFERENTIAL | POWER_MODE0) #define TOUCH_MSR_Y (START | MEASURE_Y | MODE_12BIT | DIFFERENTIAL | POWER_MODE0) /* 以下定义XPT2046 的触摸屏位置*/ #if defined(_ILI_HORIZONTAL_DIRECTION_) #define MIN_X_DEFAULT 2047 #define MAX_X_DEFAULT 47 #define MIN_Y_DEFAULT 102 #define MAX_Y_DEFAULT 1939 #else #define MIN_X_DEFAULT 47 #define MAX_X_DEFAULT 2047 #define MIN_Y_DEFAULT 1939 #define MAX_Y_DEFAULT 102 #endif #define SAMP_CNT 8 //the adc array size #define SAMP_CNT_DIV2 4 //the middle of the adc array #define SH 10 // Valve value /*宏定义 */ #define TOUCH_SPI_X SPI1 #define TOUCH_INT_PIN 84 #define TOUCH_CS_PIN 49 #define TOUCH_SCK_PIN 46 #define TOUCH_MISO_PIN 47 #define TOUCH_MOSI_PIN 48 /*创建结构体将需要用到的东西进行打包*/ struct rtgui_touch_device { struct rt_device parent; /* 用于注册设备*/ rt_uint16_t x, y; /* 记录读取到的位置值 */ rt_bool_t calibrating; /* 触摸校准标志 */ rt_touch_calibration_func_t calibration_func;/* 触摸函数 函数指针 */ rt_uint16_t min_x, max_x; /* 校准后 X 方向最小 最大值 */ rt_uint16_t min_y, max_y; /* 校准后 Y 方向最小 最大值 */ struct rt_spi_device * spi_device; /* SPI 设备 用于通信 */ struct rt_event event; /* 事件同步，用于“笔中断” */ }; static struct rtgui_touch_device *touch = RT_NULL; static rt_err_t touch_send_then_recv(struct rt_spi_device *device, const void *send_buf, rt_size_t send_length, void *recv_buf, rt_size_t recv_length) { rt_err_t result; struct rt_spi_message message; rt_uint8_t dummy[128] ; rt_memset(dummy, DUMMY, sizeof(dummy)); RT_ASSERT(device != RT_NULL); RT_ASSERT(device->bus != RT_NULL); result = rt_mutex_take(&(device->bus->lock), RT_WAITING_FOREVER); if (result == RT_EOK) { if (device->bus->owner != device) { /* not the same owner as current, re-configure SPI bus */ result = device->bus->ops->configure(device, &device->config); if (result == RT_EOK) { /* set SPI bus owner */ device->bus->owner = device; } else { /* configure SPI bus failed */ result = -RT_EIO; goto __exit; } } /* send data */ message.send_buf = send_buf; message.recv_buf = RT_NULL; message.length = send_length; message.cs_take = 1; message.cs_release = 0; message.next = RT_NULL; result = device->bus->ops->xfer(device, &message); if (result == 0) { result = -RT_EIO; goto __exit; } /* recv data */ message.send_buf = dummy; message.recv_buf = recv_buf; message.length = recv_length; message.cs_take = 0; message.cs_release = 1; message.next = RT_NULL; result = device->bus->ops->xfer(device, &message); if (result == 0) { result = -RT_EIO; goto __exit; } result = RT_EOK; } else { return -RT_EIO; } __exit: rt_mutex_release(&(device->bus->lock)); return result; } static void rtgui_touch_calculate(void) { if (touch != RT_NULL) { /* read touch */ { rt_uint8_t i, j, k, min; rt_uint16_t temp; rt_uint16_t tmpxy[2][SAMP_CNT]; rt_uint8_t send_buffer[1]; rt_uint8_t recv_buffer[2]; for(i=0; ispi_device, send_buffer, 1, recv_buffer, 2); rt_kprintf("touch x: %d ",(recv_buffer[0]*256|recv_buffer[1])>>4); #if defined(_ILI_HORIZONTAL_DIRECTION_) tmpxy[1][i] = (recv_buffer[0]<<8)|recv_buffer[1] ; tmpxy[1][i] >>= 4; #else tmpxy[0][i] = (recv_buffer[0]<<8)|recv_buffer[1] ; tmpxy[0][i] >>=4; #endif send_buffer[0] = TOUCH_MSR_Y; touch_send_then_recv(touch->spi_device, send_buffer, 1, recv_buffer, 2); rt_kprintf("touch y: %d \n",(recv_buffer[0]*256|recv_buffer[1])>>4); #if defined(_ILI_HORIZONTAL_DIRECTION_) tmpxy[0][i] = (recv_buffer[0]<<8)|recv_buffer[1] ; tmpxy[0][i] >>= 4; #else tmpxy[1][i] = (recv_buffer[0]<<8)|recv_buffer[1] ; tmpxy[1][i] >>= 4; #endif } /*再次打开触摸中断*/ send_buffer[0] = 1 << 7; touch_send_then_recv(touch->spi_device, send_buffer, 1, recv_buffer, 2); touch_send_then_recv(touch->spi_device, send_buffer, 1, recv_buffer, 2); /* calculate average */ { rt_uint32_t total_x = 0; rt_uint32_t total_y = 0; for(k=0; k<2; k++) { // sorting the ADC value for(i=0; i tmpxy[k][j]) min=j; } temp = tmpxy[k][i]; tmpxy[k][i] = tmpxy[k][min]; tmpxy[k][min] = temp; } //check value for Valve value if((tmpxy[k][SAMP_CNT_DIV2+1]-tmpxy[k][SAMP_CNT_DIV2-2]) > SH) { return; } } total_x=tmpxy[0][SAMP_CNT_DIV2-2]+tmpxy[0][SAMP_CNT_DIV2-1]+tmpxy[0][SAMP_CNT_DIV2]+tmpxy[0][SAMP_CNT_DIV2+1]; total_y=tmpxy[1][SAMP_CNT_DIV2-2]+tmpxy[1][SAMP_CNT_DIV2-1]+tmpxy[1][SAMP_CNT_DIV2]+tmpxy[1][SAMP_CNT_DIV2+1]; //calculate average value touch->x=total_x>>2; touch->y=total_y>>2; rt_kprintf("touch->x:%d touch->y:%d\r\n", touch->x, touch->y); } /* calculate average */ } /* read touch */ /* if it's not in calibration status */ /*触摸值缩放*/ if (touch->calibrating != RT_TRUE) { if (touch->max_x > touch->min_x) { touch->x = (touch->x - touch->min_x) * X_WIDTH/(touch->max_x - touch->min_x); } else { touch->x = (touch->min_x - touch->x) * X_WIDTH/(touch->min_x - touch->max_x); } if (touch->max_y > touch->min_y) { touch->y = (touch->y - touch->min_y) * Y_WIDTH /(touch->max_y - touch->min_y); } else { touch->y = (touch->min_y - touch->y) * Y_WIDTH /(touch->min_y - touch->max_y); } } } } #include "ls1c_regs.h" #define TOUCH_INT_EN __REG32(LS1C_INT4_EN) rt_inline void touch_int_cmd(rt_bool_t NewState) { if(NewState == RT_TRUE) { //TOUCH_INT_EN |= (1<<(TOUCH_INT_PIN-64)); reg_set_one_bit(LS1C_INT4_EN, 1<<(TOUCH_INT_PIN-64)); } else { //TOUCH_INT_EN &=(~ (1<<(TOUCH_INT_PIN-64))); reg_clr_one_bit(LS1C_INT4_EN, 1<<(TOUCH_INT_PIN-64)); } } void ls1c_touch_irqhandler(void) /* TouchScreen */ { if(gpio_get(TOUCH_INT_PIN)==0) { /* 触摸屏按下后操作 */ if (gpio_level_low == gpio_get(led_gpio)) gpio_set(led_gpio, gpio_level_high); else gpio_set(led_gpio, gpio_level_low); touch_int_cmd(RT_FALSE); rt_event_send(&touch->event, 1); } } /*管脚初始化，配置中断打开SPI1 CS0 设备*/ rt_inline void touch_init(void) { unsigned int touch_int_gpio = TOUCH_INT_PIN; // 触摸屏中断 int touch_irq = LS1C_GPIO_TO_IRQ(touch_int_gpio); // 初始化按键中断 gpio_set_irq_type(touch_int_gpio, IRQ_TYPE_EDGE_FALLING); rt_hw_interrupt_install(touch_irq, ls1c_touch_irqhandler, RT_NULL, "touch"); rt_hw_interrupt_umask(touch_irq); gpio_init(touch_int_gpio, gpio_mode_input); // 初始化led gpio_init(led_gpio, gpio_mode_output); gpio_set(led_gpio, gpio_level_high); } /* RT-Thread Device Interface */ static rt_err_t rtgui_touch_init (rt_device_t dev) { rt_uint8_t send; rt_uint8_t recv_buffer[2]; struct rtgui_touch_device * touch_device = (struct rtgui_touch_device *)dev; touch_init(); rt_kprintf("touch_init ...\n"); send = START | DIFFERENTIAL | POWER_MODE0; touch_send_then_recv(touch->spi_device, &send, 1, recv_buffer, 2); return RT_EOK; } static rt_err_t rtgui_touch_control (rt_device_t dev, int cmd, void *args) { switch (cmd) { case RT_TOUCH_CALIBRATION: touch->calibrating = RT_TRUE; touch->calibration_func = (rt_touch_calibration_func_t)args; break; case RT_TOUCH_NORMAL: touch->calibrating = RT_FALSE; break; case RT_TOUCH_CALIBRATION_DATA: { struct calibration_data* data; data = (struct calibration_data*) args; //update touch->min_x = data->min_x; touch->max_x = data->max_x; touch->min_y = data->min_y; touch->max_y = data->max_y; } break; } return RT_EOK; } void _set_mouse_position(rt_uint32_t X, rt_uint32_t Y) {} static void touch_thread_entry(void *parameter) { rt_bool_t touch_down = RT_FALSE; rt_uint32_t event_value; struct rtgui_event_mouse emouse; static struct _touch_previous { rt_uint32_t x; rt_uint32_t y; } touch_previous; RTGUI_EVENT_MOUSE_BUTTON_INIT(&emouse); emouse.wid = RT_NULL; while(1) { /* 接收到触摸中断事件 */ if(rt_event_recv(&touch->event, 1, RT_EVENT_FLAG_OR | RT_EVENT_FLAG_CLEAR, 100, &event_value) == RT_EOK) { while(1) { if (IS_TOUCH_UP()) { /* 触摸笔抬起 */ /* touch up */ emouse.button = (RTGUI_MOUSE_BUTTON_LEFT |RTGUI_MOUSE_BUTTON_UP); /* use old value */ emouse.x = touch->x; emouse.y = touch->y; if(touch_down != RT_TRUE) { touch_int_cmd(RT_TRUE); break; } if ((touch->calibrating == RT_TRUE) && (touch->calibration_func != RT_NULL)) { /* 触摸校准处理 */ /* callback function */ touch->calibration_func(emouse.x, emouse.y); } else { /* 向ui发送触摸坐标 */ rtgui_server_post_event(&emouse.parent, sizeof(struct rtgui_event_mouse)); } rt_kprintf("touch up: (%d, %d)\n", emouse.x, emouse.y); /* clean */ touch_previous.x = touch_previous.y = 0; touch_down = RT_FALSE; touch_int_cmd(RT_TRUE); break; } /* touch up */ else /* touch down or move */ { if(touch_down == RT_FALSE) { rt_thread_delay(RT_TICK_PER_SECOND / 10); } else { rt_thread_delay(5); } if(IS_TOUCH_UP()) continue; /* calculation */ rtgui_touch_calculate(); /* send mouse event */ emouse.parent.type = RTGUI_EVENT_MOUSE_BUTTON; emouse.parent.sender = RT_NULL; emouse.x = touch->x; emouse.y = touch->y; _set_mouse_position(emouse.x, emouse.y); /* 光标跟随 */ /* init mouse button */ emouse.button = (RTGUI_MOUSE_BUTTON_LEFT |RTGUI_MOUSE_BUTTON_DOWN); /* send event to server */ if (touch->calibrating != RT_TRUE) { #define previous_keep 8 /* filter. */ if((touch_previous.x > touch->x + previous_keep) || (touch_previous.x < touch->x - previous_keep) || (touch_previous.y > touch->y + previous_keep) || (touch_previous.y < touch->y - previous_keep)) { touch_previous.x = touch->x; touch_previous.y = touch->y; /* 向ui发送触摸坐标 */ rtgui_server_post_event(&emouse.parent, sizeof(struct rtgui_event_mouse)); if(touch_down == RT_FALSE) { touch_down = RT_TRUE; rt_kprintf("touch down: (%d, %d)\n", emouse.x, emouse.y); } else { rt_kprintf("touch motion: (%d, %d)\n", emouse.x, emouse.y); } } } else { touch_down = RT_TRUE; } } /* touch down or move */ } /* read touch */ } /* event recv */ } /* thread while(1) */ } rt_err_t rtgui_touch_hw_init(const char * spi_device_name) { rt_uint32_t arg[2]; struct rt_device * spi_device; struct rt_thread * touch_thread; rt_err_t err; rt_kprintf("spi1 cs0 start...\n"); spi_device = rt_device_find("spi10"); if(spi_device == RT_NULL) { rt_kprintf("Did not find spi1, exit thread....\n"); return; } err = rt_device_open(spi_device, RT_DEVICE_OFLAG_RDWR); if(err != RT_EOK) { rt_kprintf("Open spi1 failed %08X, exit thread....\n", err); return; } /* config spi */ { struct rt_spi_configuration cfg; cfg.data_width = 8; cfg.mode = RT_SPI_MODE_0; cfg.max_hz = 200 * 1000; /* 200K */ rt_spi_configure((struct rt_spi_device *)spi_device, &cfg); } touch = (struct rtgui_touch_device*)rt_malloc (sizeof(struct rtgui_touch_device)); if (touch == RT_NULL) return -RT_ENOMEM; /* no memory yet */ /* clear device structure */ rt_memset(&(touch->parent), 0, sizeof(struct rt_device)); rt_event_init(&touch->event, "touch", RT_IPC_FLAG_FIFO); touch->spi_device = (struct rt_spi_device *)spi_device; touch->calibrating = false; touch->min_x = MIN_X_DEFAULT; touch->max_x = MAX_X_DEFAULT; touch->min_y = MIN_Y_DEFAULT; touch->max_y = MAX_Y_DEFAULT; /* init device structure */ touch->parent.type = RT_Device_Class_Miscellaneous; touch->parent.init = rtgui_touch_init; touch->parent.control = rtgui_touch_control; touch->parent.user_data = RT_NULL; /* register touch device to RT-Thread */ rt_device_register(&(touch->parent), "touch", RT_DEVICE_FLAG_RDWR); touch_thread = rt_thread_create("touch_thread", touch_thread_entry, RT_NULL, 4096, RTGUI_SVR_THREAD_PRIORITY-1, 1); if (touch_thread != RT_NULL) rt_thread_startup(touch_thread); rt_device_init((rt_device_t)touch); return RT_EOK; } #endif