menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_RS232_TO_USART
        bool "Enable RS232 TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q64 spi3)"
        select BSP_USING_SPI
        select BSP_USING_SPI3
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_SDCARD
        bool "Enable SDCARD (sdio)"
        select BSP_USING_SDIO
        select RT_USING_DFS
        select RT_USING_DFS_ELMFAT
        default n

    config BSP_USING_MPU6050
        bool "Enable MPU6050(i2c2)"
        select BSP_USING_I2C2
        select PKG_USING_MPU6XXX
        select PKG_USING_MPU6XXX_SAMPLE
        select PKG_USING_MPU6XXX_LATEST_VERSION
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default y

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI3
                bool "Enable SPI3 BUS"
                default n

            config BSP_SPI3_TX_USING_DMA
                bool "Enable SPI3 TX DMA"
                depends on BSP_USING_SPI3
                default n

            config BSP_SPI3_RX_USING_DMA
                bool "Enable SPI3 RX DMA"
                depends on BSP_USING_SPI3
                select BSP_SPI3_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_I2C2
        bool "Enable I2C2 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C2
            comment "Notice: PH4 --> 116; PH5 --> 117"
            config BSP_I2C2_SCL_PIN
                int "i2c2 scl pin number"
                range 1 143
                default 116
            config BSP_I2C2_SDA_PIN
                int "I2C2 sda pin number"
                range 1 143
                default 117
        endif

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM11
                bool "Enable TIM11"
                default n

            config BSP_USING_TIM13
                bool "Enable TIM13"
                default n

            config BSP_USING_TIM14
                bool "Enable TIM14"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM10
            bool "Enable timer10 output PWM"
            default n
            if BSP_USING_PWM10
                config BSP_USING_PWM10_CH1
                    bool "Enable PWM10 channel1"
                    default n
            endif
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    config BSP_USING_SDIO
        bool "Enable SDIO"
        select RT_USING_SDIO
        select RT_USING_DFS
        default n

    source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"

endmenu

endmenu