/**************************************************************************//** * @file qspi.h * @version V3.00 * @brief M480 series QSPI driver header file * * @copyright (C) 2016 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __QSPI_H__ #define __QSPI_H__ #ifdef __cplusplus extern "C" { #endif /** @addtogroup Standard_Driver Standard Driver @{ */ /** @addtogroup QSPI_Driver QSPI Driver @{ */ /** @addtogroup QSPI_EXPORTED_CONSTANTS QSPI Exported Constants @{ */ #define QSPI_MODE_0 (QSPI_CTL_TXNEG_Msk) /*!< CLKPOL=0; RXNEG=0; TXNEG=1 \hideinitializer */ #define QSPI_MODE_1 (QSPI_CTL_RXNEG_Msk) /*!< CLKPOL=0; RXNEG=1; TXNEG=0 \hideinitializer */ #define QSPI_MODE_2 (QSPI_CTL_CLKPOL_Msk | QSPI_CTL_RXNEG_Msk) /*!< CLKPOL=1; RXNEG=1; TXNEG=0 \hideinitializer */ #define QSPI_MODE_3 (QSPI_CTL_CLKPOL_Msk | QSPI_CTL_TXNEG_Msk) /*!< CLKPOL=1; RXNEG=0; TXNEG=1 \hideinitializer */ #define QSPI_SLAVE (QSPI_CTL_SLAVE_Msk) /*!< Set as slave \hideinitializer */ #define QSPI_MASTER (0x0U) /*!< Set as master \hideinitializer */ #define QSPI_SS (QSPI_SSCTL_SS_Msk) /*!< Set SS \hideinitializer */ #define QSPI_SS_ACTIVE_HIGH (QSPI_SSCTL_SSACTPOL_Msk) /*!< SS active high \hideinitializer */ #define QSPI_SS_ACTIVE_LOW (0x0U) /*!< SS active low \hideinitializer */ /* QSPI Interrupt Mask */ #define QSPI_UNIT_INT_MASK (0x001U) /*!< Unit transfer interrupt mask \hideinitializer */ #define QSPI_SSACT_INT_MASK (0x002U) /*!< Slave selection signal active interrupt mask \hideinitializer */ #define QSPI_SSINACT_INT_MASK (0x004U) /*!< Slave selection signal inactive interrupt mask \hideinitializer */ #define QSPI_SLVUR_INT_MASK (0x008U) /*!< Slave under run interrupt mask \hideinitializer */ #define QSPI_SLVBE_INT_MASK (0x010U) /*!< Slave bit count error interrupt mask \hideinitializer */ #define QSPI_TXUF_INT_MASK (0x040U) /*!< Slave TX underflow interrupt mask \hideinitializer */ #define QSPI_FIFO_TXTH_INT_MASK (0x080U) /*!< FIFO TX threshold interrupt mask \hideinitializer */ #define QSPI_FIFO_RXTH_INT_MASK (0x100U) /*!< FIFO RX threshold interrupt mask \hideinitializer */ #define QSPI_FIFO_RXOV_INT_MASK (0x200U) /*!< FIFO RX overrun interrupt mask \hideinitializer */ #define QSPI_FIFO_RXTO_INT_MASK (0x400U) /*!< FIFO RX time-out interrupt mask \hideinitializer */ /* QSPI Status Mask */ #define QSPI_BUSY_MASK (0x01U) /*!< Busy status mask \hideinitializer */ #define QSPI_RX_EMPTY_MASK (0x02U) /*!< RX empty status mask \hideinitializer */ #define QSPI_RX_FULL_MASK (0x04U) /*!< RX full status mask \hideinitializer */ #define QSPI_TX_EMPTY_MASK (0x08U) /*!< TX empty status mask \hideinitializer */ #define QSPI_TX_FULL_MASK (0x10U) /*!< TX full status mask \hideinitializer */ #define QSPI_TXRX_RESET_MASK (0x20U) /*!< TX or RX reset status mask \hideinitializer */ #define QSPI_QSPIEN_STS_MASK (0x40U) /*!< QSPIEN status mask \hideinitializer */ #define QSPI_SSLINE_STS_MASK (0x80U) /*!< QSPIx_SS line status mask \hideinitializer */ /*@}*/ /* end of group QSPI_EXPORTED_CONSTANTS */ /** @addtogroup QSPI_EXPORTED_FUNCTIONS QSPI Exported Functions @{ */ /** * @brief Clear the unit transfer interrupt flag. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Write 1 to UNITIF bit of QSPI_STATUS register to clear the unit transfer interrupt flag. * \hideinitializer */ #define QSPI_CLR_UNIT_TRANS_INT_FLAG(qspi) ((qspi)->STATUS = QSPI_STATUS_UNITIF_Msk) /** * @brief Trigger RX PDMA function. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Set RXPDMAEN bit of QSPI_PDMACTL register to enable RX PDMA transfer function. * \hideinitializer */ #define QSPI_TRIGGER_RX_PDMA(qspi) ((qspi)->PDMACTL |= QSPI_PDMACTL_RXPDMAEN_Msk) /** * @brief Trigger TX PDMA function. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Set TXPDMAEN bit of QSPI_PDMACTL register to enable TX PDMA transfer function. * \hideinitializer */ #define QSPI_TRIGGER_TX_PDMA(qspi) ((qspi)->PDMACTL |= QSPI_PDMACTL_TXPDMAEN_Msk) /** * @brief Disable RX PDMA transfer. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Clear RXPDMAEN bit of QSPI_PDMACTL register to disable RX PDMA transfer function. * \hideinitializer */ #define QSPI_DISABLE_RX_PDMA(qspi) ( (qspi)->PDMACTL &= ~QSPI_PDMACTL_RXPDMAEN_Msk ) /** * @brief Disable TX PDMA transfer. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Clear TXPDMAEN bit of QSPI_PDMACTL register to disable TX PDMA transfer function. * \hideinitializer */ #define QSPI_DISABLE_TX_PDMA(qspi) ( (qspi)->PDMACTL &= ~QSPI_PDMACTL_TXPDMAEN_Msk ) /** * @brief Get the count of available data in RX FIFO. * @param[in] qspi The pointer of the specified QSPI module. * @return The count of available data in RX FIFO. * @details Read RXCNT (QSPI_STATUS[27:24]) to get the count of available data in RX FIFO. * \hideinitializer */ #define QSPI_GET_RX_FIFO_COUNT(qspi) (((qspi)->STATUS & QSPI_STATUS_RXCNT_Msk) >> QSPI_STATUS_RXCNT_Pos) /** * @brief Get the RX FIFO empty flag. * @param[in] qspi The pointer of the specified QSPI module. * @retval 0 RX FIFO is not empty. * @retval 1 RX FIFO is empty. * @details Read RXEMPTY bit of QSPI_STATUS register to get the RX FIFO empty flag. * \hideinitializer */ #define QSPI_GET_RX_FIFO_EMPTY_FLAG(qspi) (((qspi)->STATUS & QSPI_STATUS_RXEMPTY_Msk)>>QSPI_STATUS_RXEMPTY_Pos) /** * @brief Get the TX FIFO empty flag. * @param[in] qspi The pointer of the specified QSPI module. * @retval 0 TX FIFO is not empty. * @retval 1 TX FIFO is empty. * @details Read TXEMPTY bit of QSPI_STATUS register to get the TX FIFO empty flag. * \hideinitializer */ #define QSPI_GET_TX_FIFO_EMPTY_FLAG(qspi) (((qspi)->STATUS & QSPI_STATUS_TXEMPTY_Msk)>>QSPI_STATUS_TXEMPTY_Pos) /** * @brief Get the TX FIFO full flag. * @param[in] qspi The pointer of the specified QSPI module. * @retval 0 TX FIFO is not full. * @retval 1 TX FIFO is full. * @details Read TXFULL bit of QSPI_STATUS register to get the TX FIFO full flag. * \hideinitializer */ #define QSPI_GET_TX_FIFO_FULL_FLAG(qspi) (((qspi)->STATUS & QSPI_STATUS_TXFULL_Msk)>>QSPI_STATUS_TXFULL_Pos) /** * @brief Get the datum read from RX register. * @param[in] qspi The pointer of the specified QSPI module. * @return Data in RX register. * @details Read QSPI_RX register to get the received datum. * \hideinitializer */ #define QSPI_READ_RX(qspi) ((qspi)->RX) /** * @brief Write datum to TX register. * @param[in] qspi The pointer of the specified QSPI module. * @param[in] u32TxData The datum which user attempt to transfer through QSPI bus. * @return None. * @details Write u32TxData to QSPI_TX register. * \hideinitializer */ #define QSPI_WRITE_TX(qspi, u32TxData) ((qspi)->TX = (u32TxData)) /** * @brief Set QSPIx_SS pin to high state. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Disable automatic slave selection function and set QSPIx_SS pin to high state. * \hideinitializer */ #define QSPI_SET_SS_HIGH(qspi) ((qspi)->SSCTL = ((qspi)->SSCTL & (~QSPI_SSCTL_AUTOSS_Msk)) | (QSPI_SSCTL_SSACTPOL_Msk | QSPI_SSCTL_SS_Msk)) /** * @brief Set QSPIx_SS pin to low state. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Disable automatic slave selection function and set QSPIx_SS pin to low state. * \hideinitializer */ #define QSPI_SET_SS_LOW(qspi) ((qspi)->SSCTL = ((qspi)->SSCTL & (~(QSPI_SSCTL_AUTOSS_Msk | QSPI_SSCTL_SSACTPOL_Msk))) | QSPI_SSCTL_SS_Msk) /** * @brief Enable Byte Reorder function. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Enable Byte Reorder function. The suspend interval depends on the setting of SUSPITV (QSPI_CTL[7:4]). * \hideinitializer */ #define QSPI_ENABLE_BYTE_REORDER(qspi) ((qspi)->CTL |= QSPI_CTL_REORDER_Msk) /** * @brief Disable Byte Reorder function. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Clear REORDER bit field of QSPI_CTL register to disable Byte Reorder function. * \hideinitializer */ #define QSPI_DISABLE_BYTE_REORDER(qspi) ((qspi)->CTL &= ~QSPI_CTL_REORDER_Msk) /** * @brief Set the length of suspend interval. * @param[in] qspi The pointer of the specified QSPI module. * @param[in] u32SuspCycle Decides the length of suspend interval. It could be 0 ~ 15. * @return None. * @details Set the length of suspend interval according to u32SuspCycle. * The length of suspend interval is ((u32SuspCycle + 0.5) * the length of one QSPI bus clock cycle). * \hideinitializer */ #define QSPI_SET_SUSPEND_CYCLE(qspi, u32SuspCycle) ((qspi)->CTL = ((qspi)->CTL & ~QSPI_CTL_SUSPITV_Msk) | ((u32SuspCycle) << QSPI_CTL_SUSPITV_Pos)) /** * @brief Set the QSPI transfer sequence with LSB first. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Set LSB bit of QSPI_CTL register to set the QSPI transfer sequence with LSB first. * \hideinitializer */ #define QSPI_SET_LSB_FIRST(qspi) ((qspi)->CTL |= QSPI_CTL_LSB_Msk) /** * @brief Set the QSPI transfer sequence with MSB first. * @param[in] qspi The pointer of the specified SPI module. * @return None. * @details Clear LSB bit of QSPI_CTL register to set the QSPI transfer sequence with MSB first. * \hideinitializer */ #define QSPI_SET_MSB_FIRST(qspi) ((qspi)->CTL &= ~QSPI_CTL_LSB_Msk) /** * @brief Set the data width of a QSPI transaction. * @param[in] qspi The pointer of the specified QSPI module. * @param[in] u32Width The bit width of one transaction. * @return None. * @details The data width can be 8 ~ 32 bits. * \hideinitializer */ #define QSPI_SET_DATA_WIDTH(qspi, u32Width) ((qspi)->CTL = ((qspi)->CTL & ~QSPI_CTL_DWIDTH_Msk) | (((u32Width)&0x1F) << QSPI_CTL_DWIDTH_Pos)) /** * @brief Get the QSPI busy state. * @param[in] qspi The pointer of the specified QSPI module. * @retval 0 QSPI controller is not busy. * @retval 1 QSPI controller is busy. * @details This macro will return the busy state of QSPI controller. * \hideinitializer */ #define QSPI_IS_BUSY(qspi) ( ((qspi)->STATUS & QSPI_STATUS_BUSY_Msk)>>QSPI_STATUS_BUSY_Pos ) /** * @brief Enable QSPI controller. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Set QSPIEN (QSPI_CTL[0]) to enable QSPI controller. * \hideinitializer */ #define QSPI_ENABLE(qspi) ((qspi)->CTL |= QSPI_CTL_QSPIEN_Msk) /** * @brief Disable QSPI controller. * @param[in] qspi The pointer of the specified QSPI module. * @return None. * @details Clear QSPIEN (QSPI_CTL[0]) to disable QSPI controller. * \hideinitializer */ #define QSPI_DISABLE(qspi) ((qspi)->CTL &= ~QSPI_CTL_QSPIEN_Msk) /** * @brief Disable QSPI Dual IO function. * @param[in] qspi is the base address of QSPI module. * @return none * \hideinitializer */ #define QSPI_DISABLE_DUAL_MODE(qspi) ( (qspi)->CTL &= ~QSPI_CTL_DUALIOEN_Msk ) /** * @brief Enable Dual IO function and set QSPI Dual IO direction to input. * @param[in] qspi is the base address of QSPI module. * @return none * \hideinitializer */ #define QSPI_ENABLE_DUAL_INPUT_MODE(qspi) ( (qspi)->CTL = ((qspi)->CTL & ~QSPI_CTL_DATDIR_Msk) | QSPI_CTL_DUALIOEN_Msk ) /** * @brief Enable Dual IO function and set QSPI Dual IO direction to output. * @param[in] qspi is the base address of QSPI module. * @return none * \hideinitializer */ #define QSPI_ENABLE_DUAL_OUTPUT_MODE(qspi) ( (qspi)->CTL |= QSPI_CTL_DATDIR_Msk | QSPI_CTL_DUALIOEN_Msk ) /** * @brief Disable QSPI Dual IO function. * @param[in] qspi is the base address of QSPI module. * @return none * \hideinitializer */ #define QSPI_DISABLE_QUAD_MODE(qspi) ( (qspi)->CTL &= ~QSPI_CTL_QUADIOEN_Msk ) /** * @brief Set QSPI Quad IO direction to input. * @param[in] qspi is the base address of QSPI module. * @return none * \hideinitializer */ #define QSPI_ENABLE_QUAD_INPUT_MODE(qspi) ( (qspi)->CTL = ((qspi)->CTL & ~QSPI_CTL_DATDIR_Msk) | QSPI_CTL_QUADIOEN_Msk ) /** * @brief Set QSPI Quad IO direction to output. * @param[in] qspi is the base address of QSPI module. * @return none * \hideinitializer */ #define QSPI_ENABLE_QUAD_OUTPUT_MODE(qspi) ( (qspi)->CTL |= QSPI_CTL_DATDIR_Msk | QSPI_CTL_QUADIOEN_Msk ) /* Function prototype declaration */ uint32_t QSPI_Open(QSPI_T *qspi, uint32_t u32MasterSlave, uint32_t u32QSPIMode, uint32_t u32DataWidth, uint32_t u32BusClock); void QSPI_Close(QSPI_T *qspi); void QSPI_ClearRxFIFO(QSPI_T *qspi); void QSPI_ClearTxFIFO(QSPI_T *qspi); void QSPI_DisableAutoSS(QSPI_T *qspi); void QSPI_EnableAutoSS(QSPI_T *qspi, uint32_t u32SSPinMask, uint32_t u32ActiveLevel); uint32_t QSPI_SetBusClock(QSPI_T *qspi, uint32_t u32BusClock); void QSPI_SetFIFO(QSPI_T *qspi, uint32_t u32TxThreshold, uint32_t u32RxThreshold); uint32_t QSPI_GetBusClock(QSPI_T *qspi); void QSPI_EnableInt(QSPI_T *qspi, uint32_t u32Mask); void QSPI_DisableInt(QSPI_T *qspi, uint32_t u32Mask); uint32_t QSPI_GetIntFlag(QSPI_T *qspi, uint32_t u32Mask); void QSPI_ClearIntFlag(QSPI_T *qspi, uint32_t u32Mask); uint32_t QSPI_GetStatus(QSPI_T *qspi, uint32_t u32Mask); /*@}*/ /* end of group QSPI_EXPORTED_FUNCTIONS */ /*@}*/ /* end of group QSPI_Driver */ /*@}*/ /* end of group Standard_Driver */ #ifdef __cplusplus } #endif #endif /*** (C) COPYRIGHT 2016 Nuvoton Technology Corp. ***/