//***************************************************************************** // // timer.c - Driver for the timer module. // // Copyright (c) 2005-2020 Texas Instruments Incorporated. All rights reserved. // Software License Agreement // // Redistribution and use in source and binary forms, with or without // modification, are permitted provided that the following conditions // are met: // // Redistributions of source code must retain the above copyright // notice, this list of conditions and the following disclaimer. // // Redistributions in binary form must reproduce the above copyright // notice, this list of conditions and the following disclaimer in the // documentation and/or other materials provided with the // distribution. // // Neither the name of Texas Instruments Incorporated nor the names of // its contributors may be used to endorse or promote products derived // from this software without specific prior written permission. // // THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS // "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT // LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR // A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT // OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, // SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT // LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, // DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY // THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT // (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE // OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. // // This is part of revision 2.2.0.295 of the Tiva Peripheral Driver Library. // //***************************************************************************** //***************************************************************************** // //! \addtogroup timer_api //! @{ // //***************************************************************************** #include #include #include "inc/hw_ints.h" #include "inc/hw_memmap.h" #include "inc/hw_timer.h" #include "inc/hw_types.h" #include "inc/hw_sysctl.h" #include "driverlib/debug.h" #include "driverlib/interrupt.h" #include "driverlib/tiva_timer.h" //***************************************************************************** // // A macro used to determine whether the target part supports new // configuration and control options. // //***************************************************************************** #define NEW_TIMER_CONFIGURATION CLASS_IS_TM4C129 //***************************************************************************** // // A mapping of timer base address to interrupt number. // //***************************************************************************** static const uint32_t g_ppui32TimerIntMap[][2] = { { TIMER0_BASE, INT_TIMER0A_TM4C123 }, { TIMER1_BASE, INT_TIMER1A_TM4C123 }, { TIMER2_BASE, INT_TIMER2A_TM4C123 }, { TIMER3_BASE, INT_TIMER3A_TM4C123 }, { TIMER4_BASE, INT_TIMER4A_TM4C123 }, { TIMER5_BASE, INT_TIMER5A_TM4C123 }, { WTIMER0_BASE, INT_WTIMER0A_TM4C123 }, { WTIMER1_BASE, INT_WTIMER1A_TM4C123 }, { WTIMER2_BASE, INT_WTIMER2A_TM4C123 }, { WTIMER3_BASE, INT_WTIMER3A_TM4C123 }, { WTIMER4_BASE, INT_WTIMER4A_TM4C123 }, { WTIMER5_BASE, INT_WTIMER5A_TM4C123 }, }; static const uint_fast8_t g_ui8TimerIntMapRows = sizeof(g_ppui32TimerIntMap) / sizeof(g_ppui32TimerIntMap[0]); static const uint32_t g_ppui32TimerIntMapSnowflake[][2] = { { TIMER0_BASE, INT_TIMER0A_TM4C129 }, { TIMER1_BASE, INT_TIMER1A_TM4C129 }, { TIMER2_BASE, INT_TIMER2A_TM4C129 }, { TIMER3_BASE, INT_TIMER3A_TM4C129 }, { TIMER4_BASE, INT_TIMER4A_TM4C129 }, { TIMER5_BASE, INT_TIMER5A_TM4C129 }, { TIMER6_BASE, INT_TIMER6A_TM4C129 }, { TIMER7_BASE, INT_TIMER7A_TM4C129 }, }; static const uint_fast8_t g_ui8TimerIntMapRowsSnowflake = sizeof(g_ppui32TimerIntMapSnowflake) / sizeof(g_ppui32TimerIntMapSnowflake[0]); //***************************************************************************** // //! \internal //! Checks a timer base address. //! //! \param ui32Base is the base address of the timer module. //! //! This function determines if a timer module base address is valid. //! //! \return Returns \b true if the base address is valid and \b false //! otherwise. // //***************************************************************************** #ifdef DEBUG static bool _TimerBaseValid(uint32_t ui32Base) { return((ui32Base == TIMER0_BASE) || (ui32Base == TIMER1_BASE) || (ui32Base == TIMER2_BASE) || (ui32Base == TIMER3_BASE) || (ui32Base == TIMER4_BASE) || (ui32Base == TIMER5_BASE) || (ui32Base == TIMER6_BASE) || (ui32Base == TIMER7_BASE) || (ui32Base == WTIMER0_BASE) || (ui32Base == WTIMER1_BASE) || (ui32Base == WTIMER2_BASE) || (ui32Base == WTIMER3_BASE) || (ui32Base == WTIMER4_BASE) || (ui32Base == WTIMER5_BASE)); } #endif //***************************************************************************** // //! Returns a timer modules interrupt number. //! //! \param ui32Base is the base address of the selected timer. //! \param ui32Timer specifies the timer(s) to enable; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! //! This function returns the interrupt number for a given timer module //! specified by the \e ui32Base and \e ui32Timer parameter. //! //! \return Returns a timer module's interrupt number or 0 if the interrupt //! does not exist. // //***************************************************************************** static uint32_t _TimerIntNumberGet(uint32_t ui32Base, uint32_t ui32Timer) { uint32_t ui32Int; uint_fast8_t ui8Idx, ui8Rows; const uint32_t (*ppui32SSIIntMap)[2]; // // Default interrupt map. // ppui32SSIIntMap = g_ppui32TimerIntMap; ui8Rows = g_ui8TimerIntMapRows; if(CLASS_IS_TM4C129) { ppui32SSIIntMap = g_ppui32TimerIntMapSnowflake; ui8Rows = g_ui8TimerIntMapRowsSnowflake; } // // Loop through the table that maps timer base addresses to interrupt // numbers. // for(ui8Idx = 0; ui8Idx < ui8Rows; ui8Idx++) { // // See if this base address matches. // if(ppui32SSIIntMap[ui8Idx][0] == ui32Base) { ui32Int = ppui32SSIIntMap[ui8Idx][1]; if(ui32Timer == TIMER_B) { ui32Int += 1; } // // Return the corresponding interrupt number. // return(ui32Int); } } // // The base address could not be found, so return an error. // return(0); } //***************************************************************************** // //! Enables the timer(s). //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to enable; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! //! This function enables operation of the timer module. The timer must be //! configured before it is enabled. //! //! \return None. // //***************************************************************************** void TimerEnable(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Enable the timer(s) module. // HWREG(ui32Base + TIMER_O_CTL) |= ui32Timer & (TIMER_CTL_TAEN | TIMER_CTL_TBEN); } //***************************************************************************** // //! Disables the timer(s). //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to disable; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! //! This function disables operation of the timer module. //! //! \return None. // //***************************************************************************** void TimerDisable(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Disable the timer module. // HWREG(ui32Base + TIMER_O_CTL) &= ~(ui32Timer & (TIMER_CTL_TAEN | TIMER_CTL_TBEN)); } //***************************************************************************** // //! Configures the timer(s). //! //! \param ui32Base is the base address of the timer module. //! \param ui32Config is the configuration for the timer. //! //! This function configures the operating mode of the timer(s). The timer //! module is disabled before being configured and is left in the disabled //! state. The timer can be configured to be a single full-width timer //! by using the \b TIMER_CFG_* values or a pair of half-width timers using the //! \b TIMER_CFG_A_* and \b TIMER_CFG_B_* values passed in the \e ui32Config //! parameter. //! //! The configuration is specified in \e ui32Config as one of the following //! values: //! //! - \b TIMER_CFG_ONE_SHOT - Full-width one-shot timer //! - \b TIMER_CFG_ONE_SHOT_UP - Full-width one-shot timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_PERIODIC - Full-width periodic timer //! - \b TIMER_CFG_PERIODIC_UP - Full-width periodic timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_RTC - Full-width real time clock timer //! - \b TIMER_CFG_SPLIT_PAIR - Two half-width timers //! //! When configured for a pair of half-width timers, each timer is separately //! configured. The first timer is configured by setting \e ui32Config to //! the result of a logical OR operation between one of the following values //! and \e ui32Config: //! //! - \b TIMER_CFG_A_ONE_SHOT - Half-width one-shot timer //! - \b TIMER_CFG_A_ONE_SHOT_UP - Half-width one-shot timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_A_PERIODIC - Half-width periodic timer //! - \b TIMER_CFG_A_PERIODIC_UP - Half-width periodic timer that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_A_CAP_COUNT - Half-width edge count capture //! - \b TIMER_CFG_A_CAP_COUNT_UP - Half-width edge count capture that counts //! up instead of down (not available on all parts) //! - \b TIMER_CFG_A_CAP_TIME - Half-width edge time capture //! - \b TIMER_CFG_A_CAP_TIME_UP - Half-width edge time capture that counts up //! instead of down (not available on all parts) //! - \b TIMER_CFG_A_ONE_SHOT_PWM - Half-width one shot PWM output //! - \b TIMER_CFG_A_PWM - Half-width PWM output //! //! Some Tiva devices also allow configuring an action when the timers //! reach their timeout. Please consult the data sheet for the part you are //! using to determine whether configuring actions on timers is available. //! //! One of the following can be combined with the \b TIMER_CFG_* values to //! enable an action on timer A: //! //! - \b TIMER_CFG_A_ACT_TOINTD - masks the timeout interrupt of timer A. //! - \b TIMER_CFG_A_ACT_NONE - no additional action on timeout of timer A. //! - \b TIMER_CFG_A_ACT_TOGGLE - toggle CCP on timeout of timer A. //! - \b TIMER_CFG_A_ACT_SETTO - set CCP on timeout of timer A. //! - \b TIMER_CFG_A_ACT_CLRTO - clear CCP on timeout of timer A. //! - \b TIMER_CFG_A_ACT_SETTOGTO - set CCP immediately and then toggle it on //! timeout of timer A. //! - \b TIMER_CFG_A_ACT_CLRTOGTO - clear CCP immediately and then toggle it on //! timeout of timer A. //! - \b TIMER_CFG_A_ACT_SETCLRTO - set CCP immediately and then clear it on //! timeout of timer A. //! - \b TIMER_CFG_A_ACT_CLRSETTO - clear CCP immediately and then set it on //! timeout of timer A. //! //! One of the following can be combined with the \b TIMER_CFG_* values to //! enable an action on timer B: //! //! - \b TIMER_CFG_B_ACT_TOINTD - masks the timeout interrupt of timer B. //! - \b TIMER_CFG_B_ACT_NONE - no additional action on timeout of timer B. //! - \b TIMER_CFG_B_ACT_TOGGLE - toggle CCP on timeout of timer B. //! - \b TIMER_CFG_B_ACT_SETTO - set CCP on timeout of timer B. //! - \b TIMER_CFG_B_ACT_CLRTO - clear CCP on timeout of timer B. //! - \b TIMER_CFG_B_ACT_SETTOGTO - set CCP immediately and then toggle it on //! timeout of timer B. //! - \b TIMER_CFG_B_ACT_CLRTOGTO - clear CCP immediately and then toggle it on //! timeout of timer B. //! - \b TIMER_CFG_B_ACT_SETCLRTO - set CCP immediately and then clear it on //! timeout of timer B. //! - \b TIMER_CFG_B_ACT_CLRSETTO - clear CCP immediately and then set it on //! timeout of timer B. //! //! Similarly, the second timer is configured by setting \e ui32Config to //! the result of a logical OR operation between one of the corresponding //! \b TIMER_CFG_B_* values and \e ui32Config. //! //! \return None. // //***************************************************************************** void TimerConfigure(uint32_t ui32Base, uint32_t ui32Config) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT(((ui32Config & 0xfff0ffff) == TIMER_CFG_ONE_SHOT) || ((ui32Config & 0xfff0ffff) == TIMER_CFG_ONE_SHOT_UP) || ((ui32Config & 0xfff0ffff) == TIMER_CFG_PERIODIC) || ((ui32Config & 0xfff0ffff) == TIMER_CFG_PERIODIC_UP) || ((ui32Config & 0xfff0ffff) == TIMER_CFG_RTC) || ((ui32Config & 0xff000000) == TIMER_CFG_SPLIT_PAIR)); ASSERT(((ui32Config & 0xff000000) != TIMER_CFG_SPLIT_PAIR) || ((((ui32Config & 0x000000ff) == TIMER_CFG_A_ONE_SHOT) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_ONE_SHOT_UP) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_PERIODIC) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_PERIODIC_UP) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_CAP_COUNT) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_CAP_COUNT_UP) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_CAP_TIME) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_CAP_TIME_UP) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_ONE_SHOT_PWM) || ((ui32Config & 0x000000ff) == TIMER_CFG_A_PWM)) && (((ui32Config & 0x0000ff00) == TIMER_CFG_B_ONE_SHOT) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_ONE_SHOT_UP) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_PERIODIC) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_PERIODIC_UP) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_CAP_COUNT) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_CAP_COUNT_UP) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_CAP_TIME) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_CAP_TIME_UP) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_ONE_SHOT_PWM) || ((ui32Config & 0x0000ff00) == TIMER_CFG_B_PWM)))); // // Disable the timers. // HWREG(ui32Base + TIMER_O_CTL) &= ~(TIMER_CTL_TAEN | TIMER_CTL_TBEN); // // Set the global timer configuration. // HWREG(ui32Base + TIMER_O_CFG) = ui32Config >> 24; // // Set the configuration of the A and B timers and set the TxPWMIE bit. // Note that the B timer configuration is ignored by the hardware in 32-bit // modes. // if(NEW_TIMER_CONFIGURATION) { HWREG(ui32Base + TIMER_O_TAMR) = (((ui32Config & 0x000f0000) >> 4) | (ui32Config & 0xff) | TIMER_TAMR_TAPWMIE); HWREG(ui32Base + TIMER_O_TBMR) = (((ui32Config & 0x00f00000) >> 8) | ((ui32Config >> 8) & 0xff) | TIMER_TBMR_TBPWMIE); } else { HWREG(ui32Base + TIMER_O_TAMR) = ((ui32Config & 0xff) | TIMER_TAMR_TAPWMIE); HWREG(ui32Base + TIMER_O_TBMR) = (((ui32Config >> 8) & 0xff) | TIMER_TBMR_TBPWMIE); } } //***************************************************************************** // //! Controls the output level. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to adjust; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param bInvert specifies the output level. //! //! This function configures the PWM output level for the specified timer. If //! the \e bInvert parameter is \b true, then the timer's output is made active //! low; otherwise, it is made active high. //! //! \return None. // //***************************************************************************** void TimerControlLevel(uint32_t ui32Base, uint32_t ui32Timer, bool bInvert) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Set the output levels as requested. // ui32Timer &= TIMER_CTL_TAPWML | TIMER_CTL_TBPWML; HWREG(ui32Base + TIMER_O_CTL) = (bInvert ? (HWREG(ui32Base + TIMER_O_CTL) | ui32Timer) : (HWREG(ui32Base + TIMER_O_CTL) & ~(ui32Timer))); } //***************************************************************************** // //! Enables or disables the ADC trigger output. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer to adjust; must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param bEnable specifies the desired ADC trigger state. //! //! This function controls the ADC trigger output for the specified timer. If //! the \e bEnable parameter is \b true, then the timer's ADC output trigger is //! enabled; otherwise it is disabled. //! //! \return None. // //***************************************************************************** void TimerControlTrigger(uint32_t ui32Base, uint32_t ui32Timer, bool bEnable) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // On newer devices the Timer time out ADC trigger enable must also // be set. // if(NEW_TIMER_CONFIGURATION) { uint32_t ui32Val; // // Determine which bits to set or clear in GPTMADCEV. // ui32Val = (TIMER_ADCEV_TATOADCEN | TIMER_ADCEV_TBTOADCEN); ui32Val &= ui32Timer; // // Write the GPTM ADC Event register to enable or disable the trigger // to the ADC. // HWREG(ui32Base + TIMER_O_ADCEV) = (bEnable ? (HWREG(ui32Base + TIMER_O_ADCEV) | ui32Val) : (HWREG(ui32Base + TIMER_O_ADCEV) & ~(ui32Val))); } // // Set the trigger output as requested. // Set the ADC trigger output as requested. // ui32Timer &= TIMER_CTL_TAOTE | TIMER_CTL_TBOTE; HWREG(ui32Base + TIMER_O_CTL) = (bEnable ? (HWREG(ui32Base + TIMER_O_CTL) | ui32Timer) : (HWREG(ui32Base + TIMER_O_CTL) & ~(ui32Timer))); } //***************************************************************************** // //! Controls the event type. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to be adjusted; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param ui32Event specifies the type of event; must be one of //! \b TIMER_EVENT_POS_EDGE, \b TIMER_EVENT_NEG_EDGE, or //! \b TIMER_EVENT_BOTH_EDGES. //! //! This function configures the signal edge(s) that triggers the timer when //! in capture mode. //! //! \return None. // //***************************************************************************** void TimerControlEvent(uint32_t ui32Base, uint32_t ui32Timer, uint32_t ui32Event) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Set the event type. // ui32Timer &= TIMER_CTL_TAEVENT_M | TIMER_CTL_TBEVENT_M; HWREG(ui32Base + TIMER_O_CTL) = ((HWREG(ui32Base + TIMER_O_CTL) & ~ui32Timer) | (ui32Event & ui32Timer)); } //***************************************************************************** // //! Controls the stall handling. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to be adjusted; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param bStall specifies the response to a stall signal. //! //! This function controls the stall response for the specified timer. If the //! \e bStall parameter is \b true, then the timer stops counting if the //! processor enters debug mode; otherwise the timer keeps running while in //! debug mode. //! //! \return None. // //***************************************************************************** void TimerControlStall(uint32_t ui32Base, uint32_t ui32Timer, bool bStall) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Set the stall mode. // ui32Timer &= TIMER_CTL_TASTALL | TIMER_CTL_TBSTALL; HWREG(ui32Base + TIMER_O_CTL) = (bStall ? (HWREG(ui32Base + TIMER_O_CTL) | ui32Timer) : (HWREG(ui32Base + TIMER_O_CTL) & ~(ui32Timer))); } //***************************************************************************** // //! Controls the wait on trigger handling. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to be adjusted; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param bWait specifies if the timer should wait for a trigger input. //! //! This function controls whether or not a timer waits for a trigger input to //! start counting. When enabled, the previous timer in the trigger chain must //! count to its timeout in order for this timer to start counting. Refer to //! the part's data sheet for a description of the trigger chain. //! //! \note This functionality is not available on all parts. This function //! should not be used for Timer 0A or Wide Timer 0A. //! //! \return None. // //***************************************************************************** void TimerControlWaitOnTrigger(uint32_t ui32Base, uint32_t ui32Timer, bool bWait) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Set the wait on trigger mode for timer A. // if((ui32Timer & TIMER_A) != 0) { if(bWait) { HWREG(ui32Base + TIMER_O_TAMR) |= TIMER_TAMR_TAWOT; } else { HWREG(ui32Base + TIMER_O_TAMR) &= ~(TIMER_TAMR_TAWOT); } } // // Set the wait on trigger mode for timer B. // if((ui32Timer & TIMER_B) != 0) { if(bWait) { HWREG(ui32Base + TIMER_O_TBMR) |= TIMER_TBMR_TBWOT; } else { HWREG(ui32Base + TIMER_O_TBMR) &= ~(TIMER_TBMR_TBWOT); } } } //***************************************************************************** // //! Enables RTC counting. //! //! \param ui32Base is the base address of the timer module. //! //! This function causes the timer to start counting when in RTC mode. If not //! configured for RTC mode, this function does nothing. //! //! \return None. // //***************************************************************************** void TimerRTCEnable(uint32_t ui32Base) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Enable RTC counting. // HWREG(ui32Base + TIMER_O_CTL) |= TIMER_CTL_RTCEN; } //***************************************************************************** // //! Disables RTC counting. //! //! \param ui32Base is the base address of the timer module. //! //! This function causes the timer to stop counting when in RTC mode. //! //! \return None. // //***************************************************************************** void TimerRTCDisable(uint32_t ui32Base) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Disable RTC counting. // HWREG(ui32Base + TIMER_O_CTL) &= ~(TIMER_CTL_RTCEN); } //***************************************************************************** // //! Sets the clock source for the specified timer module. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Source is the clock source for the timer module. //! //! This function sets the clock source for both timer A and timer B for the //! given timer module. The possible clock sources are the system clock //! (\b TIMER_CLOCK_SYSTEM) or the precision internal oscillator //! (\b TIMER_CLOCK_PIOSC). //! //! \note The ability to specify the timer clock source varies with the //! Tiva part in use. Please consult the data sheet for the part you are //! using to determine whether this support is available. //! //! \return None. // //***************************************************************************** void TimerClockSourceSet(uint32_t ui32Base, uint32_t ui32Source) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Source == TIMER_CLOCK_SYSTEM) || (ui32Source == TIMER_CLOCK_PIOSC)); // // Set the timer clock source. // HWREG(ui32Base + TIMER_O_CC) = ui32Source; } //***************************************************************************** // //! Returns the clock source for the specified timer module. //! //! \param ui32Base is the base address of the timer module. //! //! This function returns the clock source for the specified timer module. The //! possible clock sources are the system clock (\b TIMER_CLOCK_SYSTEM) or //! the precision internal oscillator (\b TIMER_CLOCK_PIOSC). //! //! \note The ability to specify the timer clock source varies with the //! Tiva part in use. Please consult the data sheet for the part you are //! using to determine whether this support is available. //! //! \return Returns either \b TIMER_CLOCK_SYSTEM or \b TIMER_CLOCK_PIOSC. // //***************************************************************************** uint32_t TimerClockSourceGet(uint32_t ui32Base) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Return the timer clock source. // return(HWREG(ui32Base + TIMER_O_CC)); } //***************************************************************************** // //! Sets the timer prescale value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to adjust; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param ui32Value is the timer prescale value which must be between 0 and //! 255 (inclusive) for 16/32-bit timers and between 0 and 65535 (inclusive) //! for 32/64-bit timers. //! //! This function configures the value of the input clock prescaler. The //! prescaler is only operational when in half-width mode and is used to extend //! the range of the half-width timer modes. The prescaler provides the least //! significant bits when counting down in periodic and one-shot modes; in all //! other modes, the prescaler provides the most significant bits. //! //! \note The availability of the prescaler varies with the Tiva part and //! timer mode in use. Please consult the datasheet for the part you are using //! to determine whether this support is available. //! //! \return None. // //***************************************************************************** void TimerPrescaleSet(uint32_t ui32Base, uint32_t ui32Timer, uint32_t ui32Value) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); ASSERT(ui32Value < 256); // // Set the timer A prescaler if requested. // if(ui32Timer & TIMER_A) { HWREG(ui32Base + TIMER_O_TAPR) = ui32Value; } // // Set the timer B prescaler if requested. // if(ui32Timer & TIMER_B) { HWREG(ui32Base + TIMER_O_TBPR) = ui32Value; } } //***************************************************************************** // //! Gets the timer prescale value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. //! //! This function gets the value of the input clock prescaler. The prescaler //! is only operational when in half-width mode and is used to extend the range //! of the half-width timer modes. The prescaler provides the least //! significant bits when counting down in periodic and one-shot modes; in all //! other modes, the prescaler provides the most significant bits. //! //! \note The availability of the prescaler varies with the Tiva part and //! timer mode in use. Please consult the datasheet for the part you are using //! to determine whether this support is available. //! //! \return The value of the timer prescaler. // //***************************************************************************** uint32_t TimerPrescaleGet(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Return the appropriate prescale value. // return((ui32Timer == TIMER_A) ? HWREG(ui32Base + TIMER_O_TAPR) : HWREG(ui32Base + TIMER_O_TBPR)); } //***************************************************************************** // //! Sets the timer prescale match value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to adjust; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. //! \param ui32Value is the timer prescale match value which must be between 0 //! and 255 (inclusive) for 16/32-bit timers and between 0 and 65535 //! (inclusive) for 32/64-bit timers. //! //! This function configures the value of the input clock prescaler match //! value. When in a half-width mode that uses the counter match and the //! prescaler, the prescale match effectively extends the range of the match. //! The prescaler provides the least significant bits when counting down in //! periodic and one-shot modes; in all other modes, the prescaler provides the //! most significant bits. //! //! \note The availability of the prescaler match varies with the Tiva //! part and timer mode in use. Please consult the datasheet for the part you //! are using to determine whether this support is available. //! //! \return None. // //***************************************************************************** void TimerPrescaleMatchSet(uint32_t ui32Base, uint32_t ui32Timer, uint32_t ui32Value) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); ASSERT(ui32Value < 256); // // Set the timer A prescale match if requested. // if(ui32Timer & TIMER_A) { HWREG(ui32Base + TIMER_O_TAPMR) = ui32Value; } // // Set the timer B prescale match if requested. // if(ui32Timer & TIMER_B) { HWREG(ui32Base + TIMER_O_TBPMR) = ui32Value; } } //***************************************************************************** // //! Gets the timer prescale match value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. //! //! This function gets the value of the input clock prescaler match value. //! When in a half-width mode that uses the counter match and prescaler, the //! prescale match effectively extends the range of the match. The prescaler //! provides the least significant bits when counting down in periodic and //! one-shot modes; in all other modes, the prescaler provides the most //! significant bits. //! //! \note The availability of the prescaler match varies with the Tiva //! part and timer mode in use. Please consult the datasheet for the part you //! are using to determine whether this support is available. //! //! \return The value of the timer prescale match. // //***************************************************************************** uint32_t TimerPrescaleMatchGet(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Return the appropriate prescale match value. // return((ui32Timer == TIMER_A) ? HWREG(ui32Base + TIMER_O_TAPMR) : HWREG(ui32Base + TIMER_O_TBPMR)); } //***************************************************************************** // //! Sets the timer load value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to adjust; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. Only \b TIMER_A should be used //! when the timer is configured for full-width operation. //! \param ui32Value is the load value. //! //! This function configures the timer load value; if the timer is running then //! the value is immediately loaded into the timer. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers and for half-width modes of 32/64-bit timers. Use //! TimerLoadSet64() for full-width modes of 32/64-bit timers. //! //! \return None. // //***************************************************************************** void TimerLoadSet(uint32_t ui32Base, uint32_t ui32Timer, uint32_t ui32Value) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Set the timer A load value if requested. // if(ui32Timer & TIMER_A) { HWREG(ui32Base + TIMER_O_TAILR) = ui32Value; } // // Set the timer B load value if requested. // if(ui32Timer & TIMER_B) { HWREG(ui32Base + TIMER_O_TBILR) = ui32Value; } } //***************************************************************************** // //! Gets the timer load value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for full-width operation. //! //! This function gets the currently programmed interval load value for the //! specified timer. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers and for half-width modes of 32/64-bit timers. Use //! TimerLoadGet64() for full-width modes of 32/64-bit timers. //! //! \return Returns the load value for the timer. // //***************************************************************************** uint32_t TimerLoadGet(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B)); // // Return the appropriate load value. // return((ui32Timer == TIMER_A) ? HWREG(ui32Base + TIMER_O_TAILR) : HWREG(ui32Base + TIMER_O_TBILR)); } //***************************************************************************** // //! Sets the timer load value for a 64-bit timer. //! //! \param ui32Base is the base address of the timer module. //! \param ui64Value is the load value. //! //! This function configures the timer load value for a 64-bit timer; if the //! timer is running, then the value is immediately loaded into the timer. //! //! \return None. // //***************************************************************************** void TimerLoadSet64(uint32_t ui32Base, uint64_t ui64Value) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Set the timer load value. The upper 32-bits must be written before the // lower 32-bits in order to adhere to the hardware interlocks on the // 64-bit value. // HWREG(ui32Base + TIMER_O_TBILR) = ui64Value >> 32; HWREG(ui32Base + TIMER_O_TAILR) = ui64Value & 0xffffffff; } //***************************************************************************** // //! Gets the timer load value for a 64-bit timer. //! //! \param ui32Base is the base address of the timer module. //! //! This function gets the currently programmed interval load value for the //! specified 64-bit timer. //! //! \return Returns the load value for the timer. // //***************************************************************************** uint64_t TimerLoadGet64(uint32_t ui32Base) { uint32_t ui32High1, ui32High2, ui32Low; // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Read the 64-bit load value. A read of the low 32-bits is performed // between two reads of the upper 32-bits; if the upper 32-bit values match // then the 64-bit value is consistent. If they do not match, then the // read is performed again until they do match (it should never execute the // loop body more than twice). // do { ui32High1 = HWREG(ui32Base + TIMER_O_TBILR); ui32Low = HWREG(ui32Base + TIMER_O_TAILR); ui32High2 = HWREG(ui32Base + TIMER_O_TBILR); } while(ui32High1 != ui32High2); // // Return the load value. // return(((uint64_t)ui32High1 << 32) | (uint64_t)ui32Low); } //***************************************************************************** // //! Gets the current timer value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for full-width operation. //! //! This function reads the current value of the specified timer. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers and for half-width modes of 32/64-bit timers. Use //! TimerValueGet64() for full-width modes of 32/64-bit timers. //! //! \return Returns the current value of the timer. // //***************************************************************************** uint32_t TimerValueGet(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B)); // // Return the appropriate timer value. // return((ui32Timer == TIMER_A) ? HWREG(ui32Base + TIMER_O_TAR) : HWREG(ui32Base + TIMER_O_TBR)); } //***************************************************************************** // //! Gets the current 64-bit timer value. //! //! \param ui32Base is the base address of the timer module. //! //! This function reads the current value of the specified timer. //! //! \return Returns the current value of the timer. // //***************************************************************************** uint64_t TimerValueGet64(uint32_t ui32Base) { uint32_t ui32High1, ui32High2, ui32Low; // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Read the 64-bit timer value. A read of the low 32-bits is performed // between two reads of the upper 32-bits; if the upper 32-bit values match // then the 64-bit value is consistent. If they do not match, then the // read is performed again until they do match (it should never execute the // loop body more than twice). // do { ui32High1 = HWREG(ui32Base + TIMER_O_TBR); ui32Low = HWREG(ui32Base + TIMER_O_TAR); ui32High2 = HWREG(ui32Base + TIMER_O_TBR); } while(ui32High1 != ui32High2); // // Return the timer value. // return(((uint64_t)ui32High1 << 32) | (uint64_t)ui32Low); } //***************************************************************************** // //! Sets the timer match value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s) to adjust; must be one of //! \b TIMER_A, \b TIMER_B, or \b TIMER_BOTH. Only \b TIMER_A should be used //! when the timer is configured for full-width operation. //! \param ui32Value is the match value. //! //! This function configures the match value for a timer. This value is used //! in capture count mode to determine when to interrupt the processor and in //! PWM mode to determine the duty cycle of the output signal. On some //! Tiva devices, match interrupts can also be generated in periodic and //! one-shot modes. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers and for half-width modes of 32/64-bit timers. Use //! TimerMatchSet64() for full-width modes of 32/64-bit timers. //! //! \return None. // //***************************************************************************** void TimerMatchSet(uint32_t ui32Base, uint32_t ui32Timer, uint32_t ui32Value) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Set the timer A match value if requested. // if(ui32Timer & TIMER_A) { HWREG(ui32Base + TIMER_O_TAMATCHR) = ui32Value; } // // Set the timer B match value if requested. // if(ui32Timer & TIMER_B) { HWREG(ui32Base + TIMER_O_TBMATCHR) = ui32Value; } } //***************************************************************************** // //! Gets the timer match value. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer; must be one of \b TIMER_A or //! \b TIMER_B. Only \b TIMER_A should be used when the timer is configured //! for full-width operation. //! //! This function gets the match value for the specified timer. //! //! \note This function can be used for both full- and half-width modes of //! 16/32-bit timers and for half-width modes of 32/64-bit timers. Use //! TimerMatchGet64() for full-width modes of 32/64-bit timers. //! //! \return Returns the match value for the timer. // //***************************************************************************** uint32_t TimerMatchGet(uint32_t ui32Base, uint32_t ui32Timer) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B)); // // Return the appropriate match value. // return((ui32Timer == TIMER_A) ? HWREG(ui32Base + TIMER_O_TAMATCHR) : HWREG(ui32Base + TIMER_O_TBMATCHR)); } //***************************************************************************** // //! Sets the timer match value for a 64-bit timer. //! //! \param ui32Base is the base address of the timer module. //! \param ui64Value is the match value. //! //! This function configures the match value for a timer. This value is used //! in capture count mode to determine when to interrupt the processor and in //! PWM mode to determine the duty cycle of the output signal. //! //! \return None. // //***************************************************************************** void TimerMatchSet64(uint32_t ui32Base, uint64_t ui64Value) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Set the timer match value. The upper 32-bits must be written before the // lower 32-bits in order to adhere to the hardware interlocks on the // 64-bit value. // HWREG(ui32Base + TIMER_O_TBMATCHR) = ui64Value >> 32; HWREG(ui32Base + TIMER_O_TAMATCHR) = ui64Value & 0xffffffff; } //***************************************************************************** // //! Gets the timer match value for a 64-bit timer. //! //! \param ui32Base is the base address of the timer module. //! //! This function gets the match value for the specified timer. //! //! \return Returns the match value for the timer. // //***************************************************************************** uint64_t TimerMatchGet64(uint32_t ui32Base) { uint32_t ui32High1, ui32High2, ui32Low; // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Read the 64-bit match value. A read of the low 32-bits is performed // between two reads of the upper 32-bits; if the upper 32-bit values match // then the 64-bit value is consistent. If they do not match, then the // read is performed again until they do match (it should never execute the // loop body more than twice). // do { ui32High1 = HWREG(ui32Base + TIMER_O_TBMATCHR); ui32Low = HWREG(ui32Base + TIMER_O_TAMATCHR); ui32High2 = HWREG(ui32Base + TIMER_O_TBMATCHR); } while(ui32High1 != ui32High2); // // Return the match value. // return(((uint64_t)ui32High1 << 32) | (uint64_t)ui32Low); } //***************************************************************************** // //! Registers an interrupt handler for the timer interrupt. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s); must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param pfnHandler is a pointer to the function to be called when the timer //! interrupt occurs. //! //! This function registers the handler to be called when a timer interrupt //! occurs. In addition, this function enables the global interrupt in the //! interrupt controller; specific timer interrupts must be enabled via //! TimerIntEnable(). It is the interrupt handler's responsibility to clear //! the interrupt source via TimerIntClear(). //! //! \sa IntRegister() for important information about registering interrupt //! handlers. //! //! \return None. // //***************************************************************************** void TimerIntRegister(uint32_t ui32Base, uint32_t ui32Timer, void (*pfnHandler)(void)) { uint32_t ui32Int; // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Get the interrupt number for this timer module. // ui32Int = _TimerIntNumberGet(ui32Base, ui32Timer); ASSERT(ui32Int != 0); // // Register the interrupt handler. // IntRegister(ui32Int, pfnHandler); // // Enable the interrupt. // IntEnable(ui32Int); } //***************************************************************************** // //! Unregisters an interrupt handler for the timer interrupt. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s); must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! //! This function unregisters the handler to be called when a timer interrupt //! occurs. This function also masks off the interrupt in the interrupt //! controller so that the interrupt handler is no longer called. //! //! \sa IntRegister() for important information about registering interrupt //! handlers. //! //! \return None. // //***************************************************************************** void TimerIntUnregister(uint32_t ui32Base, uint32_t ui32Timer) { uint32_t ui32Int; // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); ASSERT((ui32Timer == TIMER_A) || (ui32Timer == TIMER_B) || (ui32Timer == TIMER_BOTH)); // // Get the interrupt number for this timer module. // ui32Int = _TimerIntNumberGet(ui32Base, ui32Timer); // // Disable the interrupt. // IntDisable(ui32Int); // // Unregister the interrupt handler. // IntUnregister(ui32Int); } //***************************************************************************** // //! Enables individual timer interrupt sources. //! //! \param ui32Base is the base address of the timer module. //! \param ui32IntFlags is the bit mask of the interrupt sources to be enabled. //! //! This function enables the indicated timer interrupt sources. Only the //! sources that are enabled can be reflected to the processor interrupt; //! disabled sources have no effect on the processor. //! //! The \e ui32IntFlags parameter must be the logical OR of any combination of //! the following: //! //! - \b TIMER_TIMB_DMA - Timer B uDMA complete //! - \b TIMER_TIMA_DMA - Timer A uDMA complete //! - \b TIMER_CAPB_EVENT - Capture B event interrupt //! - \b TIMER_CAPB_MATCH - Capture B match interrupt //! - \b TIMER_TIMB_MATCH - Timer B match interrupt //! - \b TIMER_TIMB_TIMEOUT - Timer B timeout interrupt //! - \b TIMER_RTC_MATCH - RTC interrupt mask //! - \b TIMER_CAPA_EVENT - Capture A event interrupt //! - \b TIMER_CAPA_MATCH - Capture A match interrupt //! - \b TIMER_TIMA_MATCH - Timer A match interrupt //! - \b TIMER_TIMA_TIMEOUT - Timer A timeout interrupt //! //! \return None. // //***************************************************************************** void TimerIntEnable(uint32_t ui32Base, uint32_t ui32IntFlags) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Enable the specified interrupts. // HWREG(ui32Base + TIMER_O_IMR) |= ui32IntFlags; } //***************************************************************************** // //! Disables individual timer interrupt sources. //! //! \param ui32Base is the base address of the timer module. //! \param ui32IntFlags is the bit mask of the interrupt sources to be //! disabled. //! //! This function disables the indicated timer interrupt sources. Only the //! sources that are enabled can be reflected to the processor interrupt; //! disabled sources have no effect on the processor. //! //! The \e ui32IntFlags parameter has the same definition as the //! \e ui32IntFlags parameter to TimerIntEnable(). //! //! \return None. // //***************************************************************************** void TimerIntDisable(uint32_t ui32Base, uint32_t ui32IntFlags) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Disable the specified interrupts. // HWREG(ui32Base + TIMER_O_IMR) &= ~(ui32IntFlags); } //***************************************************************************** // //! Gets the current interrupt status. //! //! \param ui32Base is the base address of the timer module. //! \param bMasked is false if the raw interrupt status is required and true if //! the masked interrupt status is required. //! //! This function returns the interrupt status for the timer module. Either //! the raw interrupt status or the status of interrupts that are allowed to //! reflect to the processor can be returned. //! //! \return The current interrupt status, enumerated as a bit field of //! values described in TimerIntEnable(). // //***************************************************************************** uint32_t TimerIntStatus(uint32_t ui32Base, bool bMasked) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Return either the interrupt status or the raw interrupt status as // requested. // return(bMasked ? HWREG(ui32Base + TIMER_O_MIS) : HWREG(ui32Base + TIMER_O_RIS)); } //***************************************************************************** // //! Clears timer interrupt sources. //! //! \param ui32Base is the base address of the timer module. //! \param ui32IntFlags is a bit mask of the interrupt sources to be cleared. //! //! The specified timer interrupt sources are cleared, so that they no longer //! assert. This function must be called in the interrupt handler to keep the //! interrupt from being triggered again immediately upon exit. //! //! The \e ui32IntFlags parameter has the same definition as the //! \e ui32IntFlags parameter to TimerIntEnable(). //! //! \note Because there is a write buffer in the Cortex-M processor, it may //! take several clock cycles before the interrupt source is actually cleared. //! Therefore, it is recommended that the interrupt source be cleared early in //! the interrupt handler (as opposed to the very last action) to avoid //! returning from the interrupt handler before the interrupt source is //! actually cleared. Failure to do so may result in the interrupt handler //! being immediately reentered (because the interrupt controller still sees //! the interrupt source asserted). //! //! \return None. // //***************************************************************************** void TimerIntClear(uint32_t ui32Base, uint32_t ui32IntFlags) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Clear the requested interrupt sources. // HWREG(ui32Base + TIMER_O_ICR) = ui32IntFlags; } //***************************************************************************** // //! Synchronizes the counters in a set of timers. //! //! \param ui32Base is the base address of the timer module. This parameter //! must be the base address of Timer0 (in other words, \b TIMER0_BASE). //! \param ui32Timers is the set of timers to synchronize. //! //! This function synchronizes the counters in a specified set of timers. //! When a timer is running in half-width mode, each half can be included or //! excluded in the synchronization event. When a timer is running in //! full-width mode, only the A timer can be synchronized (specifying the B //! timer has no effect). //! //! The \e ui32Timers parameter is the logical OR of any of the following //! defines: //! //! - \b TIMER_0A_SYNC //! - \b TIMER_0B_SYNC //! - \b TIMER_1A_SYNC //! - \b TIMER_1B_SYNC //! - \b TIMER_2A_SYNC //! - \b TIMER_2B_SYNC //! - \b TIMER_3A_SYNC //! - \b TIMER_3B_SYNC //! - \b TIMER_4A_SYNC //! - \b TIMER_4B_SYNC //! - \b TIMER_5A_SYNC //! - \b TIMER_5B_SYNC //! - \b WTIMER_0A_SYNC //! - \b WTIMER_0B_SYNC //! - \b WTIMER_1A_SYNC //! - \b WTIMER_1B_SYNC //! - \b WTIMER_2A_SYNC //! - \b WTIMER_2B_SYNC //! - \b WTIMER_3A_SYNC //! - \b WTIMER_3B_SYNC //! - \b WTIMER_4A_SYNC //! - \b WTIMER_4B_SYNC //! - \b WTIMER_5A_SYNC //! - \b WTIMER_5B_SYNC //! //! \note This functionality is not available on all parts. //! //! \return None. // //***************************************************************************** void TimerSynchronize(uint32_t ui32Base, uint32_t ui32Timers) { // // Check the arguments. // ASSERT(ui32Base == TIMER0_BASE); // // Synchronize the specified timers. // HWREG(ui32Base + TIMER_O_SYNC) = ui32Timers; } //***************************************************************************** // //! Enables the events that can cause an ADC trigger event. //! //! \param ui32Base is the base address of the timer module. //! \param ui32ADCEvent is a bit mask of the events that can cause an ADC //! trigger event. //! //! This function enables the timer events that can cause an ADC trigger event. //! The ADC trigger events are specified in the \e ui32ADCEvent parameter by //! passing in the logical OR of any of the following values: //! //! - \b TIMER_ADC_MODEMATCH_B - Enables the mode match ADC trigger for timer //! B. //! - \b TIMER_ADC_CAPEVENT_B - Enables the capture event ADC trigger for //! timer B. //! - \b TIMER_ADC_CAPMATCH_B - Enables the capture match ADC trigger for //! timer B. //! - \b TIMER_ADC_TIMEOUT_B - Enables the timeout ADC trigger for timer B. //! - \b TIMER_ADC_MODEMATCH_A - Enables the mode match ADC trigger for timer //! A. //! - \b TIMER_ADC_RTC_A - Enables the RTC ADC trigger for timer A. //! - \b TIMER_ADC_CAPEVENT_A - Enables the capture event ADC trigger for //! timer A. //! - \b TIMER_ADC_CAPMATCH_A - Enables the capture match ADC trigger for //! timer A. //! - \b TIMER_ADC_TIMEOUT_A - Enables the timeout ADC trigger for timer A. //! //! \note The ability to specify ADC event triggers varies with the Tiva //! part in use. Please consult the data sheet for the part you are //! using to determine whether this support is available. //! //! \return None. // //***************************************************************************** void TimerADCEventSet(uint32_t ui32Base, uint32_t ui32ADCEvent) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Set the ADC triggers. // HWREG(ui32Base + TIMER_O_ADCEV) = ui32ADCEvent; } //***************************************************************************** // //! Returns the events that can cause an ADC trigger event. //! //! \param ui32Base is the base address of the timer module. //! //! This function returns the timer events that can cause an ADC trigger event. //! The ADC trigger events are the logical OR of any of the following values: //! //! - \b TIMER_ADC_MODEMATCH_B - The mode match ADC trigger for timer B is //! enabled. //! - \b TIMER_ADC_CAPEVENT_B - The capture event ADC trigger for timer B is //! enabled. //! - \b TIMER_ADC_CAPMATCH_B - The capture match ADC trigger for timer B is //! enabled. //! - \b TIMER_ADC_TIMEOUT_B - The timeout ADC trigger for timer B is enabled. //! - \b TIMER_ADC_MODEMATCH_A - The mode match ADC trigger for timer A is //! enabled. //! - \b TIMER_ADC_RTC_A - The RTC ADC trigger for timer A is enabled. //! - \b TIMER_ADC_CAPEVENT_A - The capture event ADC trigger for timer A is //! enabled. //! - \b TIMER_ADC_CAPMATCH_A - The capture match ADC trigger for timer A is //! enabled. //! - \b TIMER_ADC_TIMEOUT_A - The timeout ADC trigger for timer A is enabled. //! //! \note The ability to specify ADC event triggers varies with the Tiva //! part in use. Please consult the data sheet for the part you are //! using to determine whether this support is available. //! //! \return The timer events that trigger the ADC. // //***************************************************************************** uint32_t TimerADCEventGet(uint32_t ui32Base) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Return the current ADC triggers. // return(HWREG(ui32Base + TIMER_O_ADCEV)); } //***************************************************************************** // //! Enables the events that can trigger a uDMA request. //! //! \param ui32Base is the base address of the timer module. //! \param ui32DMAEvent is a bit mask of the events that can trigger uDMA. //! //! This function enables the timer events that can trigger the start of a uDMA //! sequence. The uDMA trigger events are specified in the \e ui32DMAEvent //! parameter by passing in the logical OR of the following values: //! //! - \b TIMER_DMA_MODEMATCH_B - The mode match uDMA trigger for timer B is //! enabled. //! - \b TIMER_DMA_CAPEVENT_B - The capture event uDMA trigger for timer B is //! enabled. //! - \b TIMER_DMA_CAPMATCH_B - The capture match uDMA trigger for timer B is //! enabled. //! - \b TIMER_DMA_TIMEOUT_B - The timeout uDMA trigger for timer B is enabled. //! - \b TIMER_DMA_MODEMATCH_A - The mode match uDMA trigger for timer A is //! enabled. //! - \b TIMER_DMA_RTC_A - The RTC uDMA trigger for timer A is enabled. //! - \b TIMER_DMA_CAPEVENT_A - The capture event uDMA trigger for timer A is //! enabled. //! - \b TIMER_DMA_CAPMATCH_A - The capture match uDMA trigger for timer A is //! enabled. //! - \b TIMER_DMA_TIMEOUT_A - The timeout uDMA trigger for timer A is enabled. //! //! \note The ability to specify uDMA event triggers varies with the Tiva //! part in use. Please consult the data sheet for the part you are //! using to determine whether this support is available. //! //! \return None. // //***************************************************************************** void TimerDMAEventSet(uint32_t ui32Base, uint32_t ui32DMAEvent) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Set the uDMA triggers. // HWREG(ui32Base + TIMER_O_DMAEV) = ui32DMAEvent; } //***************************************************************************** // //! Returns the events that can trigger a uDMA request. //! //! \param ui32Base is the base address of the timer module. //! //! This function returns the timer events that can trigger the start of a uDMA //! sequence. The uDMA trigger events are the logical OR of the following //! values: //! //! - \b TIMER_DMA_MODEMATCH_B - Enables the mode match uDMA trigger for timer //! B. //! - \b TIMER_DMA_CAPEVENT_B - Enables the capture event uDMA trigger for //! timer B. //! - \b TIMER_DMA_CAPMATCH_B - Enables the capture match uDMA trigger for //! timer B. //! - \b TIMER_DMA_TIMEOUT_B - Enables the timeout uDMA trigger for timer B. //! - \b TIMER_DMA_MODEMATCH_A - Enables the mode match uDMA trigger for timer //! A. //! - \b TIMER_DMA_RTC_A - Enables the RTC uDMA trigger for timer A. //! - \b TIMER_DMA_CAPEVENT_A - Enables the capture event uDMA trigger for //! timer A. //! - \b TIMER_DMA_CAPMATCH_A - Enables the capture match uDMA trigger for //! timer A. //! - \b TIMER_DMA_TIMEOUT_A - Enables the timeout uDMA trigger for timer A. //! //! \note The ability to specify uDMA event triggers varies with the Tiva //! part in use. Please consult the data sheet for the part you are //! using to determine whether this support is available. //! //! \return The timer events that trigger the uDMA. // //***************************************************************************** uint32_t TimerDMAEventGet(uint32_t ui32Base) { // // Check the arguments. // ASSERT(_TimerBaseValid(ui32Base)); // // Return the current uDMA triggers. // return(HWREG(ui32Base + TIMER_O_DMAEV)); } //***************************************************************************** // //! This function configures the update of timer load and match settings. //! //! \param ui32Base is the base address of the timer module. //! \param ui32Timer specifies the timer(s); must be one of \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH. //! \param ui32Config is a combination of the updates methods for the timers //! specified in the \e ui32Timer parameter. //! //! This function configures how the timer updates the timer load and match //! values for the timers. The \e ui32Timer values can be \b TIMER_A, //! \b TIMER_B, or \b TIMER_BOTH to apply the settings in \e ui32Config to //! either timer or both timers. If the timer is not split then the \b TIMER_A //! should be used. The \e ui32Config values affects when the TimerLoadSet() //! and TimerLoadSet64() values take effect. //! //! - \b TIMER_UP_LOAD_IMMEDIATE is the default mode that causes the //! TimerLoadSet() or TimerLoadSet64() to update the timer counter immediately. //! - \b TIMER_UP_LOAD_TIMEOUT causes the TimerLoadSet() or TimerLoadSet64() to //! update the timer when it counts down to zero. //! //! Similarly the \e ui32Config value affects when the TimerMatchSet() and //! TimerMatchSet64() values take effect. //! //! - \b TIMER_UP_MATCH_IMMEDIATE is the default mode that causes the //! TimerMatchSet() or TimerMatchSet64() to update the timer match value //! immediately. //! - \b TIMER_UP_MATCH_TIMEOUT causes the TimerMatchSet() or TimerMatchSet64() //! to update the timer match value when it counts down to zero. //! //! \note These settings have no effect if the timer is not in count down mode //! and are mostly useful when operating in PWM mode to allow for synchronous //! update of timer match and load values. //! //! \return None. // //***************************************************************************** void TimerUpdateMode(uint32_t ui32Base, uint32_t ui32Timer, uint32_t ui32Config) { uint32_t ui32Value; if((ui32Timer & TIMER_A) == TIMER_A) { ui32Value = HWREG(ui32Base + TIMER_O_TAMR) & ~(0x00000500); ui32Value |= ui32Config; HWREG(ui32Base + TIMER_O_TAMR) = ui32Value; } if((ui32Timer & TIMER_B) == TIMER_B) { ui32Value = HWREG(ui32Base + TIMER_O_TBMR) & ~(0x00000500); ui32Value |= ui32Config; HWREG(ui32Base + TIMER_O_TBMR) = ui32Value; } } //***************************************************************************** // // Close the Doxygen group. //! @} // //*****************************************************************************