menu "Hardware Drivers Config"

config SOC_STM32F103ZE
    bool
    select SOC_SERIES_STM32F1
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "Onboard Peripheral Drivers"

    config BSP_USING_USB_TO_USART
        bool "Enable USB TO USART (uart1)"
        select BSP_USING_UART
        select BSP_USING_UART1
        default y

    config BSP_USING_EEPROM
        bool "Enable I2C EEPROM (i2c1)"
        select BSP_USING_I2C1
        default n

    config BSP_USING_SPI_FLASH
        bool "Enable SPI FLASH (W25Q16 spi2)"
	select BSP_USING_SPI
        select BSP_USING_SPI2
        select RT_USING_SFUD
        select RT_SFUD_USING_SFDP
        default n

    config BSP_USING_POT
        bool "Enable potentiometer"
        select BSP_USING_ADC
        select BSP_USING_ADC1
        default n 

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n
                
            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n  
        endif    

    menuconfig BSP_USING_TIM
        bool "Enable timer"
        default n
        select RT_USING_HWTIMER
        if BSP_USING_TIM
            config BSP_USING_TIM2
                bool "Enable TIM2"
                default n

            config BSP_USING_TIM3
                bool "Enable TIM3"
                default n

            config BSP_USING_TIM4
                bool "Enable TIM4"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable pwm"
        default n
        select RT_USING_PWM
        if BSP_USING_PWM
        menuconfig BSP_USING_PWM3
            bool "Enable timer3 output pwm"
            default n
            if BSP_USING_PWM3
                config BSP_USING_PWM3_CH1
                    bool "Enable PWM3 channel1"
                    default n

                config BSP_USING_PWM3_CH2
                    bool "Enable PWM3 channel2"
                    default n
            endif
        endif
	
    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n
                        
            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n  
                        
            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n
                        
            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n
        endif

    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 63
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 63
                default 23
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n 

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        select RT_USING_LIBC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n

    menuconfig BSP_USING_PULSE_ENCODER
        bool "Enable Pulse Encoder"
        default n
        select RT_USING_PULSE_ENCODER
        if BSP_USING_PULSE_ENCODER
            config BSP_USING_PULSE_ENCODER3
                bool "Enable Pulse Encoder3"
                default n

        endif

 source "../libraries/HAL_Drivers/Kconfig"
    
endmenu

menu "Board extended module Drivers"

endmenu

endmenu