menu "Hardware Drivers Config"

config BSP_USING_HYPERFLASH
    bool
    default n

config SOC_MIMXRT1052DVL6B
    bool
    select SOC_MIMXRT1050_SERIES
    select BSP_USING_HYPERFLASH
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_DMA
        bool "Enable DMA"
        default n
        
    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_LPUART
        bool "Enable UART"
        select RT_USING_SERIAL
        default y
        
        if BSP_USING_LPUART
            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default y

                config BSP_LPUART1_RX_USING_DMA
                    bool "Enable LPUART1 RX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_RX_DMA_CHANNEL
                        depends on BSP_LPUART1_RX_USING_DMA
                        int "Set LPUART1 RX DMA channel (0-32)"
                        default 0

                config BSP_LPUART1_TX_USING_DMA
                    bool "Enable LPUART1 TX DMA"
                    depends on BSP_USING_LPUART1
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART1_TX_DMA_CHANNEL
                        depends on BSP_LPUART1_TX_USING_DMA
                        int "Set LPUART1 TX DMA channel (0-32)"
                        default 1

            config BSP_USING_LPUART3
                bool "Enable LPUART3"
                default n

                config BSP_LPUART3_RX_USING_DMA
                    bool "Enable LPUART3 RX DMA"
                    depends on BSP_USING_LPUART3
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART3_RX_DMA_CHANNEL
                        depends on BSP_LPUART3_RX_USING_DMA
                        int "Set LPUART3 RX DMA channel (0-32)"
                        default 0

                config BSP_LPUART3_TX_USING_DMA
                    bool "Enable LPUART3 TX DMA"
                    depends on BSP_USING_LPUART3
                    select BSP_USING_DMA
                    select RT_SERIAL_USING_DMA
                    default n

                    config BSP_LPUART3_TX_DMA_CHANNEL
                        depends on BSP_LPUART3_TX_USING_DMA
                        int "Set LPUART3 TX DMA channel (0-32)"
                        default 1
        endif

endmenu

menu "Onboard Peripheral Drivers"

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n

    menuconfig BSP_USING_ETH
	bool "Enable Ethernet"
	select RT_USING_NETDEV
	default n
    

	if BSP_USING_ETH
		config BSP_USING_PHY
            select RT_USING_PHY
			bool "Enable ethernet phy"
			default y

	    if BSP_USING_PHY
            config PHY_DEVICE_ADDRESS
                int "Specify address of phy device"
                default 2

            config PHY_USING_KSZ8081
                bool "i.MX RT1064EVK uses ksz8081 phy"
                default y

            if PHY_USING_KSZ8081
                config PHY_RESET_PORT
                    int "indicate port of reset"
                    default 1

                config PHY_RESET_PIN
                    int "indicate pin of reset"
                    default 9
                
                config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
                    bool "Enable the PHY ksz8081 RMII50M mode"
                    depends on PHY_USING_KSZ8081
                    default y
            endif

        endif
	endif
endmenu

menu "Board extended module Drivers"

endmenu

endmenu