menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"
    config BSP_USING_RS485_OR_RS232
        bool "Enable RS485/RS232 (uart4 be shared)"
        select BSP_USING_UART4
        default n
    config BSP_USING_ETH
        bool "Enable Ethernet Driver (spi2)"
        default n
        select PKG_USING_WIZNET
        select WIZNET_DEVICE_EXTERN_CONFIG
        select BSP_USING_SPI2
        if BSP_USING_ETH
            if WIZNET_DEVICE_EXTERN_CONFIG
                config WIZ_SPI_DEVICE
                    string
                    default "spi20"

                config WIZ_RST_PIN
                    int
                    default 56

                config WIZ_IRQ_PIN
                    int
                    default 57
            endif

            config EXTERNAL_PHY_ADDRESS
                hex
                default 0x00

        endif
    config BSP_USING_LORA
        bool "Enable LoRa Driver (spi1)"
        default n
        select PKG_USING_SX12XX
        select SX12XX_DEVICE_EXTERN_CONFIG
        select BSP_USING_SPI1
        if BSP_USING_LORA
            if SX12XX_DEVICE_EXTERN_CONFIG
            config SX12XX_SPI_DEVICE
                string "SPI device name"
                default "spi10"

            config SX12XX_RST_PIN
                int "Reset PIN number"
                default 7

            config SX12XX_DO0_PIN
                int "DO0 PIN number"
                default 103

            config SX12XX_DO1_PIN
                int "DO1 PIN number"
                default 104

            config SX12XX_DO2_PIN
                int "DO2 PIN number"
                default 105

            config SX12XX_DO3_PIN
                int "DO3 PIN number"
                default 106

            config SX12XX_DO4_PIN
                int "DO4 PIN number"
                default 107

            config SX12XX_DO5_PIN
                int "DO5 PIN number"
                default 108

            endif

        endif
endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART1
                bool "Enable UART1"
                default y

            config BSP_UART1_RX_USING_DMA
                bool "Enable UART1 RX DMA"
                depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                default n
            config BSP_USING_UART2
                bool "Enable UART2"
                default n

            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default n

            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART4
                bool "Enable UART4"
                default n

            config BSP_UART4_RX_USING_DMA
                bool "Enable UART4 RX DMA"
                depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
        endif
    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n
    menuconfig BSP_USING_I2C1
        bool "Enable I2C1 BUS (software simulation)"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN
        if BSP_USING_I2C1
            config BSP_I2C1_SCL_PIN
                int "i2c1 scl pin number"
                range 0 144
                default 22
            config BSP_I2C1_SDA_PIN
                int "I2C1 sda pin number"
                range 0 144
                default 23
        endif
    menuconfig BSP_USING_SPI
        bool "Enable SPI BUS"
        default n
        select RT_USING_SPI
        if BSP_USING_SPI
            config BSP_USING_SPI1
                bool "Enable SPI1 BUS"
                default n

            config BSP_SPI1_TX_USING_DMA
                bool "Enable SPI1 TX DMA"
                depends on BSP_USING_SPI1
                default n

            config BSP_SPI1_RX_USING_DMA
                bool "Enable SPI1 RX DMA"
                depends on BSP_USING_SPI1
                select BSP_SPI1_TX_USING_DMA
                default n

            config BSP_USING_SPI2
                bool "Enable SPI2 BUS"
                default n

            config BSP_SPI2_TX_USING_DMA
                bool "Enable SPI2 TX DMA"
                depends on BSP_USING_SPI2
                default n

            config BSP_SPI2_RX_USING_DMA
                bool "Enable SPI2 RX DMA"
                depends on BSP_USING_SPI2
                select BSP_SPI2_TX_USING_DMA
                default n

        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_ONCHIP_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default n
        if BSP_USING_ONCHIP_RTC
            choice
                prompt "Select clock source"
                default BSP_RTC_USING_LSE

                config BSP_RTC_USING_LSE
                    bool "RTC USING LSE"

                config BSP_RTC_USING_LSI
                    bool "RTC USING LSI"
            endchoice
        endif

    config BSP_USING_WDT
        bool "Enable Watchdog Timer"
        select RT_USING_WDT
        default n
    source "$BSP_DIR/../libraries/HAL_Drivers/drivers/Kconfig"

endmenu

menu "Board extended module Drivers"
    config BSP_USING_WIFI_OR_GPRS
        bool "Enable WIFI/GPRS (uart3 be shared)"
        select BSP_USING_UART3
        default n
endmenu

endmenu