/*!
    \file  gd32f4xx_sdio.c
    \brief SDIO driver
*/

/*
    Copyright (C) 2016 GigaDevice

    2016-08-15, V1.0.0, firmware for GD32F4xx
*/

#include "gd32f4xx_sdio.h"

/*!
    \brief      deinitialize the SDIO
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_deinit(void)
{
    rcu_periph_reset_enable(RCU_SDIORST);
    rcu_periph_reset_disable(RCU_SDIORST);
}

/*!
    \brief      configure the SDIO clock
    \param[in]  clock_edge: SDIO_CLK clock edge
      \arg        SDIO_SDIOCLKEDGE_RISING: select the rising edge of the SDIOCLK to generate SDIO_CLK
      \arg        SDIO_SDIOCLKEDGE_FALLING: select the falling edge of the SDIOCLK to generate SDIO_CLK
    \param[in]  clock_bypass: clock bypass
      \arg        SDIO_CLOCKBYPASS_ENABLE: clock bypass
      \arg        SDIO_CLOCKBYPASS_DISABLE: no bypass
    \param[in]  clock_powersave: SDIO_CLK clock dynamic switch on/off for power saving
      \arg        SDIO_CLOCKPWRSAVE_ENABLE: SDIO_CLK closed when bus is idle
      \arg        SDIO_CLOCKPWRSAVE_DISABLE: SDIO_CLK clock is always on
    \param[in]  clock_division: clock division, less than 512
    \param[out] none
    \retval     none
*/
void sdio_clock_config(uint32_t clock_edge, uint32_t clock_bypass, uint32_t clock_powersave, uint16_t clock_division)
{
    uint32_t clock_config = 0U;
    clock_config = SDIO_CLKCTL;
    /* reset the CLKEDGE, CLKBYP, CLKPWRSAV, DIV */
    clock_config &= ~(SDIO_CLKCTL_CLKEDGE | SDIO_CLKCTL_CLKBYP | SDIO_CLKCTL_CLKPWRSAV | SDIO_CLKCTL_DIV8 | SDIO_CLKCTL_DIV);
    /* if the clock division is greater or equal to 256, set the DIV[8] */
    if(clock_division >= 256U){
        clock_config |= SDIO_CLKCTL_DIV8;
        clock_division -= 256U;
    }
    /* configure the SDIO_CLKCTL according to the parameters */
    clock_config |= (clock_edge | clock_bypass | clock_powersave | clock_division);
    SDIO_CLKCTL = clock_config;
}

/*!
    \brief      enable hardware clock control
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_hardware_clock_enable(void)
{
    SDIO_CLKCTL |= SDIO_CLKCTL_HWCLKEN;
}

/*!
    \brief      disable hardware clock control
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_hardware_clock_disable(void)
{
    SDIO_CLKCTL &= ~SDIO_CLKCTL_HWCLKEN;
}

/*!
    \brief      set different SDIO card bus mode
    \param[in]  bus_mode: SDIO card bus mode
      \arg        SDIO_BUSMODE_1BIT: 1-bit SDIO card bus mode
      \arg        SDIO_BUSMODE_4BIT: 4-bit SDIO card bus mode
      \arg        SDIO_BUSMODE_8BIT: 8-bit SDIO card bus mode
    \param[out] none
    \retval     none
*/
void sdio_bus_mode_set(uint32_t bus_mode)
{
    /* reset the SDIO card bus mode bits and set according to bus_mode */
    SDIO_CLKCTL &= ~SDIO_CLKCTL_BUSMODE;
    SDIO_CLKCTL |= bus_mode;
}

/*!
    \brief      set the SDIO power state
    \param[in]  power_state: SDIO power state
      \arg        SDIO_POWER_ON: SDIO power on
      \arg        SDIO_POWER_OFF: SDIO power off
    \param[out] none
    \retval     none
*/
void sdio_power_state_set(uint32_t power_state)
{
    SDIO_PWRCTL = power_state;
}

/* get the SDIO power state */
/*!
    \brief      get the SDIO power state
    \param[in]  none
    \param[out] none
    \retval     SDIO power state
      \arg        SDIO_POWER_ON: SDIO power on
      \arg        SDIO_POWER_OFF: SDIO power off
*/
uint32_t sdio_power_state_get(void)
{
    return SDIO_PWRCTL;
}

/*!
    \brief      enable SDIO_CLK clock output
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_clock_enable(void)
{
    SDIO_CLKCTL |= SDIO_CLKCTL_CLKEN;
}

/*!
    \brief      disable SDIO_CLK clock output
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_clock_disable(void)
{
    SDIO_CLKCTL &= ~SDIO_CLKCTL_CLKEN;
}

/*!
    \brief      configure the command and response
    \param[in]  cmd_index: command index, refer to the related specifications
    \param[in]  cmd_argument: command argument, refer to the related specifications
    \param[in]  response_type: response type
      \arg        SDIO_RESPONSETYPE_NO: no response
      \arg        SDIO_RESPONSETYPE_SHORT: short response
      \arg        SDIO_RESPONSETYPE_LONG: long response
    \param[out] none
    \retval     none
*/
void sdio_command_response_config(uint32_t cmd_index, uint32_t cmd_argument, uint32_t response_type)
{
    uint32_t cmd_config = 0U;
    /* reset the command index, command argument and response type */
    SDIO_CMDAGMT &= ~SDIO_CMDAGMT_CMDAGMT;
    SDIO_CMDAGMT = cmd_argument;
    cmd_config = SDIO_CMDCTL;
    cmd_config &= ~(SDIO_CMDCTL_CMDIDX | SDIO_CMDCTL_CMDRESP);
    /* configure SDIO_CMDCTL and SDIO_CMDAGMT according to the parameters */
    cmd_config |= (cmd_index | response_type);
    SDIO_CMDCTL = cmd_config;
}

/*!
    \brief      set the command state machine wait type
    \param[in]  wait_type: wait type
      \arg        SDIO_WAITTYPE_NO: not wait interrupt
      \arg        SDIO_WAITTYPE_INTERRUPT: wait interrupt
      \arg        SDIO_WAITTYPE_DATAEND: wait the end of data transfer
    \param[out] none
    \retval     none
*/
void sdio_wait_type_set(uint32_t wait_type)
{
    /* reset INTWAIT and WAITDEND */
    SDIO_CMDCTL &= ~(SDIO_CMDCTL_INTWAIT | SDIO_CMDCTL_WAITDEND);
    /* set the wait type according to wait_type */
    SDIO_CMDCTL |= wait_type;
}

/*!
    \brief      enable the CSM(command state machine)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_csm_enable(void)
{
    SDIO_CMDCTL |= SDIO_CMDCTL_CSMEN;
}

/*!
    \brief      disable the CSM(command state machine)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_csm_disable(void)
{
    SDIO_CMDCTL &= ~SDIO_CMDCTL_CSMEN;
}

/*!
    \brief      get the last response command index
    \param[in]  none
    \param[out] none
    \retval     last response command index
*/
uint8_t sdio_command_index_get(void)
{
    return (uint8_t)SDIO_RSPCMDIDX;
}

/*!
    \brief      get the response for the last received command
    \param[in]  sdio_responsex: SDIO response
      \arg       SDIO_RESPONSE0: card response[31:0]/card response[127:96]
      \arg       SDIO_RESPONSE1: card response[95:64]
      \arg       SDIO_RESPONSE2: card response[63:32]
      \arg       SDIO_RESPONSE3: card response[31:1], plus bit 0
    \param[out] none
    \retval     response for the last received command
*/
uint32_t sdio_response_get(uint32_t sdio_responsex)
{
    uint32_t resp_content = 0U;
    switch(sdio_responsex){
    case SDIO_RESPONSE0:
        resp_content = SDIO_RESP0;
        break;
    case SDIO_RESPONSE1:
        resp_content = SDIO_RESP1;
        break;
    case SDIO_RESPONSE2:
        resp_content = SDIO_RESP2;
        break;
    case SDIO_RESPONSE3:
        resp_content = SDIO_RESP3;
        break;
    default:
        break;
    }
    return resp_content;
}

/*!
    \brief      configure the data timeout, data length and data block size
    \param[in]  data_timeout: data timeout period in card bus clock periods
    \param[in]  data_length: number of data bytes to be transferred
    \param[in]  data_blocksize: size of data block for block transfer
      \arg        SDIO_DATABLOCKSIZE_1BYTE: block size = 1 byte
      \arg        SDIO_DATABLOCKSIZE_2BYTES: block size = 2 bytes
      \arg        SDIO_DATABLOCKSIZE_4BYTES: block size = 4 bytes
      \arg        SDIO_DATABLOCKSIZE_8BYTES: block size = 8 bytes
      \arg        SDIO_DATABLOCKSIZE_16BYTES: block size = 16 bytes
      \arg        SDIO_DATABLOCKSIZE_32BYTES: block size = 32 bytes
      \arg        SDIO_DATABLOCKSIZE_64BYTES: block size = 64 bytes
      \arg        SDIO_DATABLOCKSIZE_128BYTES: block size = 128 bytes
      \arg        SDIO_DATABLOCKSIZE_256BYTES: block size = 256 bytes
      \arg        SDIO_DATABLOCKSIZE_512BYTES: block size = 512 bytes
      \arg        SDIO_DATABLOCKSIZE_1024BYTES: block size = 1024 bytes
      \arg        SDIO_DATABLOCKSIZE_2048BYTES: block size = 2048 bytes
      \arg        SDIO_DATABLOCKSIZE_4096BYTES: block size = 4096 bytes
      \arg        SDIO_DATABLOCKSIZE_8192BYTES: block size = 8192 bytes
      \arg        SDIO_DATABLOCKSIZE_16384BYTES: block size = 16384 bytes
    \param[out] none
    \retval     none
*/
void sdio_data_config(uint32_t data_timeout, uint32_t data_length, uint32_t data_blocksize)
{
    /* reset data timeout, data length and data block size */
    SDIO_DATATO &= ~SDIO_DATATO_DATATO;
    SDIO_DATALEN &= ~SDIO_DATALEN_DATALEN;
    SDIO_DATACTL &= ~SDIO_DATACTL_BLKSZ;
    /* configure the related parameters of data */
    SDIO_DATATO = data_timeout;
    SDIO_DATALEN = data_length;
    SDIO_DATACTL |= data_blocksize;
}

/*!
    \brief      configure the data transfer mode and direction
    \param[in]  transfer_mode: mode of data transfer
      \arg       SDIO_TRANSMODE_BLOCK: block transfer
      \arg       SDIO_TRANSMODE_STREAM: stream transfer or SDIO multibyte transfer
    \param[in]  transfer_direction: data transfer direction, read or write
      \arg       SDIO_TRANSDIRECTION_TOCARD: write data to card
      \arg       SDIO_TRANSDIRECTION_TOSDIO: read data from card
    \param[out] none
    \retval     none
*/
void sdio_data_transfer_config(uint32_t transfer_mode, uint32_t transfer_direction)
{
    uint32_t data_trans = 0U;
    /* reset the data transfer mode, transfer direction and set according to the parameters */
    data_trans = SDIO_DATACTL;
    data_trans &= ~(SDIO_DATACTL_TRANSMOD | SDIO_DATACTL_DATADIR);
    data_trans |= (transfer_mode | transfer_direction);
    SDIO_DATACTL = data_trans;
}

/*!
    \brief      enable the DSM(data state machine) for data transfer
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_dsm_enable(void)
{
    SDIO_DATACTL |= SDIO_DATACTL_DATAEN;
}

/*!
    \brief      disable the DSM(data state machine)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_dsm_disable(void)
{
    SDIO_DATACTL &= ~SDIO_DATACTL_DATAEN;
}

/*!
    \brief      write data(one word) to the transmit FIFO
    \param[in]  data: 32-bit data write to card
    \param[out] none
    \retval     none
*/
void sdio_data_write(uint32_t data)
{
    SDIO_FIFO = data;
}

/*!
    \brief      read data(one word) from the receive FIFO
    \param[in]  none
    \param[out] none
    \retval     received data
*/
uint32_t sdio_data_read(void)
{
    return SDIO_FIFO;
}

/*!
    \brief      get the number of remaining data bytes to be transferred to card
    \param[in]  none
    \param[out] none
    \retval     number of remaining data bytes to be transferred
*/
uint32_t sdio_data_counter_get(void)
{
    return SDIO_DATACNT;
}

/*!
    \brief      get the number of words remaining to be written or read from FIFO
    \param[in]  none
    \param[out] none
    \retval     remaining number of words
*/
uint32_t sdio_fifo_counter_get(void)
{
    return SDIO_FIFOCNT;
}

/*!
    \brief      enable the DMA request for SDIO
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_dma_enable(void)
{
    SDIO_DATACTL |= SDIO_DATACTL_DMAEN;
}

/*!
    \brief      disable the DMA request for SDIO
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_dma_disable(void)
{
    SDIO_DATACTL &= ~SDIO_DATACTL_DMAEN;
}

/*!
    \brief      get the flags state of SDIO
    \param[in]  flag: flags state of SDIO
      \arg        SDIO_FLAG_CCRCERR: command response received (CRC check failed) flag
      \arg        SDIO_FLAG_DTCRCERR: data block sent/received (CRC check failed) flag
      \arg        SDIO_FLAG_CMDTMOUT: command response timeout flag
      \arg        SDIO_FLAG_DTTMOUT: data timeout flag
      \arg        SDIO_FLAG_TXURE: transmit FIFO underrun error occurs flag
      \arg        SDIO_FLAG_RXORE: received FIFO overrun error occurs flag
      \arg        SDIO_FLAG_CMDRECV: command response received (CRC check passed) flag
      \arg        SDIO_FLAG_CMDSEND: command sent (no response required) flag
      \arg        SDIO_FLAG_DTEND: data end (data counter, SDIO_DATACNT, is zero) flag
      \arg        SDIO_FLAG_STBITE: start bit error in the bus flag
      \arg        SDIO_FLAG_DTBLKEND: data block sent/received (CRC check passed) flag
      \arg        SDIO_FLAG_CMDRUN: command transmission in progress flag
      \arg        SDIO_FLAG_TXRUN: data transmission in progress flag
      \arg        SDIO_FLAG_RXRUN: data reception in progress flag
      \arg        SDIO_FLAG_TFH: transmit FIFO is half empty flag: at least 8 words can be written into the FIFO
      \arg        SDIO_FLAG_RFH: receive FIFO is half full flag: at least 8 words can be read in the FIFO
      \arg        SDIO_FLAG_TFF: transmit FIFO is full flag
      \arg        SDIO_FLAG_RFF: receive FIFO is full flag
      \arg        SDIO_FLAG_TFE: transmit FIFO is empty flag
      \arg        SDIO_FLAG_RFE: receive FIFO is empty flag
      \arg        SDIO_FLAG_TXDTVAL: data is valid in transmit FIFO flag
      \arg        SDIO_FLAG_RXDTVAL: data is valid in receive FIFO flag
      \arg        SDIO_FLAG_SDIOINT: SD I/O interrupt received flag
      \arg        SDIO_FLAG_ATAEND: CE-ATA command completion signal received (only for CMD61) flag
    \param[out] none
    \retval     FlagStatus: SET or RESET
*/
FlagStatus sdio_flag_get(uint32_t flag)
{
    FlagStatus temp_flag = RESET;
    if(RESET != (SDIO_STAT & flag)){
        temp_flag = SET;
    }
    return temp_flag;
}

/*!
    \brief      clear the pending flags of SDIO
    \param[in]  flag: flags state of SDIO
      \arg        SDIO_FLAG_CCRCERR: command response received (CRC check failed) flag
      \arg        SDIO_FLAG_DTCRCERR: data block sent/received (CRC check failed) flag
      \arg        SDIO_FLAG_CMDTMOUT: command response timeout flag
      \arg        SDIO_FLAG_DTTMOUT: data timeout flag
      \arg        SDIO_FLAG_TXURE: transmit FIFO underrun error occurs flag
      \arg        SDIO_FLAG_RXORE: received FIFO overrun error occurs flag
      \arg        SDIO_FLAG_CMDRECV: command response received (CRC check passed) flag
      \arg        SDIO_FLAG_CMDSEND: command sent (no response required) flag
      \arg        SDIO_FLAG_DTEND: data end (data counter, SDIO_DATACNT, is zero) flag
      \arg        SDIO_FLAG_STBITE: start bit error in the bus flag
      \arg        SDIO_FLAG_DTBLKEND: data block sent/received (CRC check passed) flag
      \arg        SDIO_FLAG_SDIOINT: SD I/O interrupt received flag
      \arg        SDIO_FLAG_ATAEND: CE-ATA command completion signal received (only for CMD61) flag
    \param[out] none
    \retval     none
*/
void sdio_flag_clear(uint32_t flag)
{
    SDIO_INTC = flag;
}

/*!
    \brief      enable the SDIO interrupt
    \param[in]  int_flag: interrupt flags state of SDIO
      \arg        SDIO_INT_CCRCERR: SDIO CCRCERR interrupt
      \arg        SDIO_INT_DTCRCERR: SDIO DTCRCERR interrupt
      \arg        SDIO_INT_CMDTMOUT: SDIO CMDTMOUT interrupt
      \arg        SDIO_INT_DTTMOUT: SDIO DTTMOUT interrupt
      \arg        SDIO_INT_TXURE: SDIO TXURE interrupt
      \arg        SDIO_INT_RXORE: SDIO RXORE interrupt
      \arg        SDIO_INT_CMDRECV: SDIO CMDRECV interrupt
      \arg        SDIO_INT_CMDSEND: SDIO CMDSEND interrupt
      \arg        SDIO_INT_DTEND: SDIO DTEND interrupt
      \arg        SDIO_INT_STBITE: SDIO STBITE interrupt
      \arg        SDIO_INT_DTBLKEND: SDIO DTBLKEND interrupt
      \arg        SDIO_INT_CMDRUN: SDIO CMDRUN interrupt
      \arg        SDIO_INT_TXRUN: SDIO TXRUN interrupt
      \arg        SDIO_INT_RXRUN: SDIO RXRUN interrupt
      \arg        SDIO_INT_TFH: SDIO TFH interrupt
      \arg        SDIO_INT_RFH: SDIO RFH interrupt
      \arg        SDIO_INT_TFF: SDIO TFF interrupt
      \arg        SDIO_INT_RFF: SDIO RFF interrupt
      \arg        SDIO_INT_TFE: SDIO TFE interrupt
      \arg        SDIO_INT_RFE: SDIO RFE interrupt
      \arg        SDIO_INT_TXDTVAL: SDIO TXDTVAL interrupt
      \arg        SDIO_INT_RXDTVAL: SDIO RXDTVAL interrupt
      \arg        SDIO_INT_SDIOINT: SDIO SDIOINT interrupt
      \arg        SDIO_INT_ATAEND: SDIO ATAEND interrupt
    \param[out] none
    \retval     none
*/
void sdio_interrupt_enable(uint32_t int_flag)
{
    SDIO_INTEN |= int_flag;
}

/*!
    \brief      disable the SDIO interrupt
    \param[in]  int_flag: interrupt flags state of SDIO
      \arg        SDIO_INT_CCRCERR: SDIO CCRCERR interrupt
      \arg        SDIO_INT_DTCRCERR: SDIO DTCRCERR interrupt
      \arg        SDIO_INT_CMDTMOUT: SDIO CMDTMOUT interrupt
      \arg        SDIO_INT_DTTMOUT: SDIO DTTMOUT interrupt
      \arg        SDIO_INT_TXURE: SDIO TXURE interrupt
      \arg        SDIO_INT_RXORE: SDIO RXORE interrupt
      \arg        SDIO_INT_CMDRECV: SDIO CMDRECV interrupt
      \arg        SDIO_INT_CMDSEND: SDIO CMDSEND interrupt
      \arg        SDIO_INT_DTEND: SDIO DTEND interrupt
      \arg        SDIO_INT_STBITE: SDIO STBITE interrupt
      \arg        SDIO_INT_DTBLKEND: SDIO DTBLKEND interrupt
      \arg        SDIO_INT_CMDRUN: SDIO CMDRUN interrupt
      \arg        SDIO_INT_TXRUN: SDIO TXRUN interrupt
      \arg        SDIO_INT_RXRUN: SDIO RXRUN interrupt
      \arg        SDIO_INT_TFH: SDIO TFH interrupt
      \arg        SDIO_INT_RFH: SDIO RFH interrupt
      \arg        SDIO_INT_TFF: SDIO TFF interrupt
      \arg        SDIO_INT_RFF: SDIO RFF interrupt
      \arg        SDIO_INT_TFE: SDIO TFE interrupt
      \arg        SDIO_INT_RFE: SDIO RFE interrupt
      \arg        SDIO_INT_TXDTVAL: SDIO TXDTVAL interrupt
      \arg        SDIO_INT_RXDTVAL: SDIO RXDTVAL interrupt
      \arg        SDIO_INT_SDIOINT: SDIO SDIOINT interrupt
      \arg        SDIO_INT_ATAEND: SDIO ATAEND interrupt
    \param[out] none
    \retval     none
*/
void sdio_interrupt_disable(uint32_t int_flag)
{
    SDIO_INTEN &= ~int_flag;
}

/*!
    \brief      get the interrupt flags state of SDIO
    \param[in]  int_flag: interrupt flags state of SDIO
      \arg        SDIO_INT_CCRCERR: SDIO CCRCERR interrupt
      \arg        SDIO_INT_DTCRCERR: SDIO DTCRCERR interrupt
      \arg        SDIO_INT_CMDTMOUT: SDIO CMDTMOUT interrupt
      \arg        SDIO_INT_DTTMOUT: SDIO DTTMOUT interrupt
      \arg        SDIO_INT_TXURE: SDIO TXURE interrupt
      \arg        SDIO_INT_RXORE: SDIO RXORE interrupt
      \arg        SDIO_INT_CMDRECV: SDIO CMDRECV interrupt
      \arg        SDIO_INT_CMDSEND: SDIO CMDSEND interrupt
      \arg        SDIO_INT_DTEND: SDIO DTEND interrupt
      \arg        SDIO_INT_STBITE: SDIO STBITE interrupt
      \arg        SDIO_INT_DTBLKEND: SDIO DTBLKEND interrupt
      \arg        SDIO_INT_CMDRUN: SDIO CMDRUN interrupt
      \arg        SDIO_INT_TXRUN: SDIO TXRUN interrupt
      \arg        SDIO_INT_RXRUN: SDIO RXRUN interrupt
      \arg        SDIO_INT_TFH: SDIO TFH interrupt
      \arg        SDIO_INT_RFH: SDIO RFH interrupt
      \arg        SDIO_INT_TFF: SDIO TFF interrupt
      \arg        SDIO_INT_RFF: SDIO RFF interrupt
      \arg        SDIO_INT_TFE: SDIO TFE interrupt
      \arg        SDIO_INT_RFE: SDIO RFE interrupt
      \arg        SDIO_INT_TXDTVAL: SDIO TXDTVAL interrupt
      \arg        SDIO_INT_RXDTVAL: SDIO RXDTVAL interrupt
      \arg        SDIO_INT_SDIOINT: SDIO SDIOINT interrupt
      \arg        SDIO_INT_ATAEND: SDIO ATAEND interrupt
    \param[out] none
    \retval     FlagStatus: SET or RESET
*/
FlagStatus sdio_interrupt_flag_get(uint32_t int_flag)
{
    FlagStatus temp_flag = RESET;
    if(RESET != (SDIO_STAT & int_flag)){
        temp_flag = SET;
    }
    return temp_flag;
}

/*!
    \brief      clear the interrupt pending flags of SDIO
    \param[in]  int_flag: interrupt flags state of SDIO
      \arg        SDIO_INT_CCRCERR: command response received (CRC check failed) flag
      \arg        SDIO_INT_DTCRCERR: data block sent/received (CRC check failed) flag
      \arg        SDIO_INT_CMDTMOUT: command response timeout flag
      \arg        SDIO_INT_DTTMOUT: data timeout flag
      \arg        SDIO_INT_TXURE: transmit FIFO underrun error occurs flag
      \arg        SDIO_INT_RXORE: received FIFO overrun error occurs flag
      \arg        SDIO_INT_CMDRECV: command response received (CRC check passed) flag
      \arg        SDIO_INT_CMDSEND: command sent (no response required) flag
      \arg        SDIO_INT_DTEND: data end (data counter, SDIO_DATACNT, is zero) flag
      \arg        SDIO_INT_STBITE: start bit error in the bus flag
      \arg        SDIO_INT_DTBLKEND: data block sent/received (CRC check passed) flag
      \arg        SDIO_INT_SDIOINT: SD I/O interrupt received flag
      \arg        SDIO_INT_ATAEND: CE-ATA command completion signal received (only for CMD61) flag
    \param[out] none
    \retval     none
*/
void sdio_interrupt_flag_clear(uint32_t int_flag)
{
    SDIO_INTC = int_flag;
}

/*!
    \brief      enable the read wait mode(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_readwait_enable(void)
{
    SDIO_DATACTL |= SDIO_DATACTL_RWEN;
}

/*!
    \brief      disable the read wait mode(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_readwait_disable(void)
{
    SDIO_DATACTL &= ~SDIO_DATACTL_RWEN;
}

/*!
    \brief      enable the function that stop the read wait process(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_stop_readwait_enable(void)
{
    SDIO_DATACTL |= SDIO_DATACTL_RWSTOP;
}

/*!
    \brief      disable the function that stop the read wait process(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_stop_readwait_disable(void)
{
    SDIO_DATACTL &= ~SDIO_DATACTL_RWSTOP;
}

/*!
    \brief      set the read wait type(SD I/O only)
    \param[in]  readwait_type: SD I/O read wait type
      \arg        SDIO_READWAITTYPE_CLK: read wait control by stopping SDIO_CLK
      \arg        SDIO_READWAITTYPE_DAT2: read wait control using SDIO_DAT[2]
    \param[out] none
    \retval     none
*/
void sdio_readwait_type_set(uint32_t readwait_type)
{
    if(SDIO_READWAITTYPE_CLK == readwait_type){
        SDIO_DATACTL |= SDIO_DATACTL_RWTYPE;
    }else{
        SDIO_DATACTL &= ~SDIO_DATACTL_RWTYPE;
    }
}

/*!
    \brief      enable the SD I/O mode specific operation(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_operation_enable(void)
{
    SDIO_DATACTL |= SDIO_DATACTL_IOEN;
}

/*!
    \brief      disable the SD I/O mode specific operation(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_operation_disable(void)
{
    SDIO_DATACTL &= ~SDIO_DATACTL_IOEN;
}

/*!
    \brief      enable the SD I/O suspend operation(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_suspend_enable(void)
{
    SDIO_CMDCTL |= SDIO_CMDCTL_SUSPEND;
}

/*!
    \brief      disable the SD I/O suspend operation(SD I/O only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_suspend_disable(void)
{
    SDIO_CMDCTL &= ~SDIO_CMDCTL_SUSPEND;
}

/*!
    \brief      enable the CE-ATA command(CE-ATA only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_ceata_command_enable(void)
{
    SDIO_CMDCTL |= SDIO_CMDCTL_ATAEN;
}

/*!
    \brief      disable the CE-ATA command(CE-ATA only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_ceata_command_disable(void)
{
    SDIO_CMDCTL &= ~SDIO_CMDCTL_ATAEN;
}

/*!
    \brief      enable the CE-ATA interrupt(CE-ATA only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_ceata_interrupt_enable(void)
{
    SDIO_CMDCTL &= ~SDIO_CMDCTL_NINTEN;
}

/*!
    \brief      disable the CE-ATA interrupt(CE-ATA only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_ceata_interrupt_disable(void)
{
    SDIO_CMDCTL |= SDIO_CMDCTL_NINTEN;
}

/*!
    \brief      enable the CE-ATA command completion signal(CE-ATA only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_ceata_command_completion_enable(void)
{
    SDIO_CMDCTL |= SDIO_CMDCTL_ENCMDC;
}

/*!
    \brief      disable the CE-ATA command completion signal(CE-ATA only)
    \param[in]  none
    \param[out] none
    \retval     none
*/
void sdio_ceata_command_completion_disable(void)
{
    SDIO_CMDCTL &= ~SDIO_CMDCTL_ENCMDC;
}