menu "Hardware Drivers Config"

menu "Onboard Peripheral Drivers"

    config BSP_USING_STLINK_TO_USART
        bool "Enable STLINK TO USART (uart3)"
        select BSP_USING_UART
        select BSP_USING_UART3
        default y

    config BSP_USING_ARDUINO
        bool "Compatible with Arduino Ecosystem (RTduino)"
        select PKG_USING_RTDUINO
        select BSP_USING_STLINK_TO_USART
        select BSP_USING_GPIO
        select BSP_USING_ADC
        select BSP_USING_ADC1
        select BSP_USING_PWM
        select BSP_USING_PWM14
        select BSP_USING_PWM4
        select BSP_USING_PWM1
        select BSP_USING_PWM1_CH3
        select BSP_USING_PWM1_CH2
        select BSP_USING_PWM1_CH1
        select BSP_USING_PWM4_CH4
        select BSP_USING_PWM4_CH3
        select BSP_USING_PWM14_CH1
        select BSP_USING_I2C
        select BSP_USING_I2C1
        imply RTDUINO_USING_SERVO
        imply RTDUINO_USING_WIRE
        default n

endmenu

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        bool "Enable UART"
        default y
        select RT_USING_SERIAL
        if BSP_USING_UART
            config BSP_USING_UART2
                bool "Enable UART2"
                default y
            config BSP_UART2_RX_USING_DMA
                bool "Enable UART2 RX DMA"
                depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                default n

            config BSP_USING_UART3
                bool "Enable UART3"
                default y
            config BSP_UART3_RX_USING_DMA
                bool "Enable UART3 RX DMA"
                depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                default n
        endif

    menuconfig BSP_USING_ADC
        bool "Enable ADC"
        default n
        select RT_USING_ADC
        if BSP_USING_ADC
            config BSP_USING_ADC1
                bool "Enable ADC1"
                default n
        endif

    menuconfig BSP_USING_PWM
        bool "Enable PWM"
        default n
        select RT_USING_PWM

        if BSP_USING_PWM
            menuconfig BSP_USING_PWM1
                bool "Enable timer1 output PWM"
                default n
                if BSP_USING_PWM1
                    config BSP_USING_PWM1_CH1
                        bool "Enable PWM1 channel1"
                        default n

                    config BSP_USING_PWM1_CH2
                        bool "Enable PWM1 channel2"
                        default n

                    config BSP_USING_PWM1_CH3
                        bool "Enable PWM1 channel3"
                        default n
                endif

            menuconfig BSP_USING_PWM4
                bool "Enable timer4 output PWM"
                default n
                if BSP_USING_PWM4
                    config BSP_USING_PWM4_CH3
                        bool "Enable PWM3 channel3"
                        default n

                    config BSP_USING_PWM4_CH4
                        bool "Enable PWM4 channel4"
                        default n
                endif

            menuconfig BSP_USING_PWM14
                bool "Enable timer14 output PWM"
                default n
                if BSP_USING_PWM14
                    config BSP_USING_PWM14_CH1
                        bool "Enable PWM14 channel1"
                        default n
                endif
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C BUS"
        default n
        select RT_USING_I2C
        select RT_USING_I2C_BITOPS
        select RT_USING_PIN

        if BSP_USING_I2C
            config BSP_USING_I2C1
                bool "Enable I2C1 Bus (User I2C)"
                default n
                if BSP_USING_I2C1
                    comment "Notice: PB9 --> 25; PB8 --> 24"
                    config BSP_I2C1_SCL_PIN
                        int "i2c1 SCL pin number"
                        range 1 176
                        default 24
                    config BSP_I2C1_SDA_PIN
                        int "i2c1 SDA pin number"
                        range 1 176
                        default 25
                endif
        endif

    config BSP_USING_ON_CHIP_FLASH
        bool "Enable on-chip FLASH"
        default n

    config BSP_USING_USBD
        bool "Enable OTGFS as USB device"
        select RT_USING_USB_DEVICE
        select BSP_USBD_TYPE_FS
        default n

endmenu

menu "Board extended module Drivers"

endmenu

endmenu