menu "Hardware Drivers Config" config SOC_STM32F103ZE bool select SOC_SERIES_STM32F1 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" config BSP_USING_USB_TO_USART bool "Enable USB TO USART (uart1)" select BSP_USING_UART select BSP_USING_UART1 default y config BSP_USING_RS485_OR_RS232 bool "Enable RS485/RS232 (uart2 be shared)" select BSP_USING_UART2 default n config BSP_USING_SPI_FLASH bool "Enable SPI FLASH (W25Q64 spi1)" select BSP_USING_SPI select BSP_USING_SPI1 select RT_USING_SFUD select RT_SFUD_USING_SFDP default n config BSP_USING_NAND1 bool "Enable NAND1" select RT_USING_NAND1 select RT_USING_MTD_NAND select PKG_USING_LPM default n config BSP_USING_RGB bool "Enable RGB LED (timer3 channel2 - 4)" select RT_USING_PWM select BSP_USING_PWM select BSP_USING_PWM3 select BSP_USING_PWM3_CH2 select BSP_USING_PWM3_CH3 select BSP_USING_PWM3_CH4 default n config BSP_USING_POT bool "Enable potentiometer" select BSP_USING_ADC select BSP_USING_ADC1 default n config BSP_USING_EEPROM bool "Enable I2C EEPROM (i2c1)" select BSP_USING_I2C1 default n config BSP_USING_ETH bool "Enable Ethernet Driver (spi2)" default n select PKG_USING_WIZNET select WIZNET_DEVICE_EXTERN_CONFIG select BSP_USING_SPI2 if BSP_USING_ETH if WIZNET_DEVICE_EXTERN_CONFIG config WIZ_SPI_DEVICE string default "spi20" config WIZ_RST_PIN int default 111 config WIZ_IRQ_PIN int default 104 endif config EXTERNAL_PHY_ADDRESS hex default 0x00 endif config BSP_USING_SDCARD bool "Enable SDCARD (sdio)" select BSP_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT default n endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default y config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_USING_UART2 bool "Enable UART2" default n config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_USING_UART3 bool "Enable UART3" default n config BSP_UART3_RX_USING_DMA bool "Enable UART3 RX DMA" depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA default n endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 BUS" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI2 bool "Enable SPI2 BUS" default n config BSP_SPI2_TX_USING_DMA bool "Enable SPI2 TX DMA" depends on BSP_USING_SPI2 default n config BSP_SPI2_RX_USING_DMA bool "Enable SPI2 RX DMA" depends on BSP_USING_SPI2 select BSP_SPI2_TX_USING_DMA default n config BSP_USING_SPI3 bool "Enable SPI3 BUS" default n config BSP_SPI3_TX_USING_DMA bool "Enable SPI3 TX DMA" depends on BSP_USING_SPI3 default n config BSP_SPI3_RX_USING_DMA bool "Enable SPI3 RX DMA" depends on BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA default n endif menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 config BSP_I2C1_SCL_PIN int "i2c1 scl pin number" range 0 175 default 22 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 0 175 default 23 endif menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM2 bool "Enable TIM2" default n config BSP_USING_TIM3 bool "Enable TIM3" default n config BSP_USING_TIM4 bool "Enable TIM4" default n config BSP_USING_TIM5 bool "Enable TIM5" default n endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM3 bool "Enable timer3 output PWM" default n if BSP_USING_PWM3 config BSP_USING_PWM3_CH2 bool "Enable PWM3 channel2" default n config BSP_USING_PWM3_CH3 bool "Enable PWM3 channel3" default n config BSP_USING_PWM3_CH4 bool "Enable PWM3 channel4" default n endif endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n menuconfig BSP_USING_CAN bool "Enable CAN" default n select RT_USING_CAN if BSP_USING_CAN config BSP_USING_CAN1 bool "using CAN1" default n endif config BSP_USING_USBD bool "Enable USB device" select RT_USING_USB_DEVICE default n if BSP_USING_USBD config BSP_USB_CONNECT_PIN int "USB connect pin" default 67 config BSP_USB_PULL_UP_STATUS int "USB PULL UP STATUS" default 0 endif source "../libraries/HAL_Drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu