/**************************************************************************//** * * @copyright (C) 2020 Nuvoton Technology Corp. All rights reserved. * * SPDX-License-Identifier: Apache-2.0 * * Change Logs: * Date Author Notes * 2021-9-27 Wayne First version * ******************************************************************************/ #include #if defined(BSP_USING_SCUART) #include "NuMicro.h" #include #include #include /* Private definition * ---------------------------------------------------------------*/ #define LOG_TAG "drv.scuart" #define DBG_ENABLE #define DBG_SECTION_NAME "drv.scuart" #define DBG_LEVEL DBG_ERROR #define DBG_COLOR #include enum { SCUART_START = -1, #if defined(BSP_USING_SCUART0) SCUART0_IDX, #endif #if defined(BSP_USING_SCUART1) SCUART1_IDX, #endif SCUART_CNT }; /* Private typedef * --------------------------------------------------------------*/ struct nu_scuart { rt_serial_t dev; char *name; SC_T *base; IRQn_Type irqn; uint32_t rstidx; uint32_t modid; }; typedef struct nu_scuart *nu_scuart_t; /* Private functions * ------------------------------------------------------------*/ static rt_err_t nu_scuart_configure(struct rt_serial_device *serial, struct serial_configure *cfg); static rt_err_t nu_scuart_control(struct rt_serial_device *serial, int cmd, void *arg); static int nu_scuart_send(struct rt_serial_device *serial, char c); static int nu_scuart_receive(struct rt_serial_device *serial); static void nu_scuart_isr(int vector, void *param); static const struct rt_uart_ops nu_scuart_ops = { .configure = nu_scuart_configure, .control = nu_scuart_control, .putc = nu_scuart_send, .getc = nu_scuart_receive, .dma_transmit = RT_NULL /* not support DMA mode */ }; static const struct serial_configure nu_scuart_default_config = RT_SERIAL_CONFIG_DEFAULT; static struct nu_scuart nu_scuart_arr[] = { #if defined(BSP_USING_SCUART0) { .name = "scuart0", .base = SC0, .irqn = SC0_IRQn, .rstidx = SC0_RST, .modid = SC0_MODULE, }, #endif #if defined(BSP_USING_SCUART1) { .name = "scuart1", .base = SC1, .irqn = SC1_IRQn, .rstidx = SC1_RST, .modid = SC1_MODULE, }, #endif }; /* scuart nu_scuart */ /** * All SCUART interrupt service routine */ static void nu_scuart_isr(int vector, void *param) { nu_scuart_t psNuSCUart = (nu_scuart_t)param; /* Handle RX event */ if (SCUART_GET_INT_FLAG(psNuSCUart->base, SC_INTSTS_RXTOIF_Msk) || SCUART_GET_INT_FLAG(psNuSCUart->base, SC_INTSTS_RDAIF_Msk)) { rt_hw_serial_isr(&psNuSCUart->dev, RT_SERIAL_EVENT_RX_IND); // RDA is the only interrupt enabled in this driver, this status bit // automatically cleared after Rx FIFO empty. So no need to clear interrupt // status here. SCUART_CLR_INT_FLAG(psNuSCUart->base, SC_INTSTS_RXTOIF_Msk); } } /** * Configure scuart port */ static rt_err_t nu_scuart_configure(struct rt_serial_device *serial, struct serial_configure *cfg) { rt_err_t ret = RT_EOK; uint32_t scuart_word_len = 0; uint32_t scuart_stop_bit = 0; uint32_t scuart_parity = 0; nu_scuart_t psNuSCUart = (nu_scuart_t)serial; RT_ASSERT(psNuSCUart); /* Check baud rate */ RT_ASSERT(cfg->baud_rate); /* Check word len */ switch (cfg->data_bits) { case DATA_BITS_5: scuart_word_len = SCUART_CHAR_LEN_5; break; case DATA_BITS_6: scuart_word_len = SCUART_CHAR_LEN_6; break; case DATA_BITS_7: scuart_word_len = SCUART_CHAR_LEN_7; break; case DATA_BITS_8: scuart_word_len = SCUART_CHAR_LEN_8; break; default: LOG_E("Unsupported data length"); ret = -RT_EINVAL; goto exit_nu_scuart_configure; } /* Check stop bit */ switch (cfg->stop_bits) { case STOP_BITS_1: scuart_stop_bit = SCUART_STOP_BIT_1; break; case STOP_BITS_2: scuart_stop_bit = SCUART_STOP_BIT_2; break; default: LOG_E("Unsupported stop bit"); ret = -RT_EINVAL; goto exit_nu_scuart_configure; } /* Check parity */ switch (cfg->parity) { case PARITY_NONE: scuart_parity = SCUART_PARITY_NONE; break; case PARITY_ODD: scuart_parity = SCUART_PARITY_ODD; break; case PARITY_EVEN: scuart_parity = SCUART_PARITY_EVEN; break; default: LOG_E("Unsupported parity"); ret = -RT_EINVAL; goto exit_nu_scuart_configure; } nu_sys_ip_reset(psNuSCUart->rstidx); /* Open SCUART and set SCUART baud rate */ SCUART_Open(psNuSCUart->base, cfg->baud_rate); /* Set line configuration. */ SCUART_SetLineConfig(psNuSCUart->base, 0, scuart_word_len, scuart_parity, scuart_stop_bit); /* Enable interrupt. */ rt_hw_interrupt_umask(psNuSCUart->irqn); exit_nu_scuart_configure: if (ret != RT_EOK) SCUART_Close(psNuSCUart->base); return -(ret); } /** * SCUART interrupt control */ static rt_err_t nu_scuart_control(struct rt_serial_device *serial, int cmd, void *arg) { rt_err_t result = RT_EOK; rt_uint32_t flag; rt_ubase_t ctrl_arg = (rt_ubase_t)arg; nu_scuart_t psNuSCUart = (nu_scuart_t)serial; RT_ASSERT(psNuSCUart); switch (cmd) { case RT_DEVICE_CTRL_CLR_INT: if (ctrl_arg == RT_DEVICE_FLAG_INT_RX) /* Disable INT-RX */ { flag = SC_INTEN_RDAIEN_Msk | SC_INTEN_RXTOIEN_Msk; SCUART_DISABLE_INT(psNuSCUart->base, flag); } break; case RT_DEVICE_CTRL_SET_INT: if (ctrl_arg == RT_DEVICE_FLAG_INT_RX) /* Enable INT-RX */ { flag = SC_INTEN_RDAIEN_Msk | SC_INTEN_RXTOIEN_Msk; SCUART_ENABLE_INT(psNuSCUart->base, flag); } break; case RT_DEVICE_CTRL_CLOSE: /* Disable interrupt. */ rt_hw_interrupt_mask(psNuSCUart->irqn); /* Close SCUART port */ SCUART_Close(psNuSCUart->base); break; default: result = -RT_EINVAL; break; } return result; } /** * SCUART put char */ static int nu_scuart_send(struct rt_serial_device *serial, char c) { nu_scuart_t psNuSCUart = (nu_scuart_t)serial; RT_ASSERT(psNuSCUart); /* Waiting if TX-FIFO is full. */ while (SCUART_IS_TX_FULL(psNuSCUart->base)) ; /* Put char into TX-FIFO */ SCUART_WRITE(psNuSCUart->base, c); return 1; } /** * SCUART get char */ static int nu_scuart_receive(struct rt_serial_device *serial) { nu_scuart_t psNuSCUart = (nu_scuart_t)serial; RT_ASSERT(psNuSCUart); /* Return failure if RX-FIFO is empty. */ if (SCUART_GET_RX_EMPTY(psNuSCUart->base)) { return -1; } /* Get char from RX-FIFO */ return SCUART_READ(psNuSCUart->base); } /** * Hardware SCUART Initialization */ static int rt_hw_scuart_init(void) { int i; rt_uint32_t flag; rt_err_t ret = RT_EOK; for (i = (SCUART_START + 1); i < SCUART_CNT; i++) { flag = RT_DEVICE_FLAG_RDWR | RT_DEVICE_FLAG_INT_RX; nu_scuart_arr[i].dev.ops = &nu_scuart_ops; nu_scuart_arr[i].dev.config = nu_scuart_default_config; SYS_ResetModule(nu_scuart_arr[i].rstidx); rt_hw_interrupt_install(nu_scuart_arr[i].irqn, nu_scuart_isr, &nu_scuart_arr[i], nu_scuart_arr[i].name); ret = rt_hw_serial_register(&nu_scuart_arr[i].dev, nu_scuart_arr[i].name, flag, NULL); RT_ASSERT(ret == RT_EOK); } return (int)ret; } INIT_DEVICE_EXPORT(rt_hw_scuart_init); #endif //#if defined(BSP_USING_SCUART)