menu "Hardware Drivers Config" config SOC_STM32F103ZE bool select SOC_SERIES_STM32F1 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" config BSP_USING_RS485_OR_RS232 bool "Enable RS485/RS232 (uart4 be shared)" select BSP_USING_UART4 default n config BSP_USING_ETH bool "Enable Ethernet Driver (spi2)" default n select PKG_USING_WIZNET select WIZNET_DEVICE_EXTERN_CONFIG select BSP_USING_SPI2 if BSP_USING_ETH if WIZNET_DEVICE_EXTERN_CONFIG config WIZ_SPI_DEVICE string default "spi20" config WIZ_RST_PIN int default 56 config WIZ_IRQ_PIN int default 57 endif config EXTERNAL_PHY_ADDRESS hex default 0x00 endif config BSP_USING_LORA bool "Enable LoRa Driver (spi1)" default n select PKG_USING_SX12XX select SX12XX_DEVICE_EXTERN_CONFIG select BSP_USING_SPI1 if BSP_USING_LORA if SX12XX_DEVICE_EXTERN_CONFIG config SX12XX_SPI_DEVICE string "SPI device name" default "spi10" config SX12XX_RST_PIN int "Reset PIN number" default 7 config SX12XX_DO0_PIN int "DO0 PIN number" default 103 config SX12XX_DO1_PIN int "DO1 PIN number" default 104 config SX12XX_DO2_PIN int "DO2 PIN number" default 105 config SX12XX_DO3_PIN int "DO3 PIN number" default 106 config SX12XX_DO4_PIN int "DO4 PIN number" default 107 config SX12XX_DO5_PIN int "DO5 PIN number" default 108 endif endif endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default y config BSP_UART1_RX_USING_DMA bool "Enable UART1 RX DMA" depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA default n config BSP_USING_UART2 bool "Enable UART2" default n config BSP_UART2_RX_USING_DMA bool "Enable UART2 RX DMA" depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA default n config BSP_USING_UART3 bool "Enable UART3" default n config BSP_UART3_RX_USING_DMA bool "Enable UART3 RX DMA" depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA default n config BSP_USING_UART4 bool "Enable UART4" default n config BSP_UART4_RX_USING_DMA bool "Enable UART4 RX DMA" depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA endif config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 config BSP_I2C1_SCL_PIN int "i2c1 scl pin number" range 0 144 default 22 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 0 144 default 23 endif menuconfig BSP_USING_SPI bool "Enable SPI BUS" default n select RT_USING_SPI if BSP_USING_SPI config BSP_USING_SPI1 bool "Enable SPI1 BUS" default n config BSP_SPI1_TX_USING_DMA bool "Enable SPI1 TX DMA" depends on BSP_USING_SPI1 default n config BSP_SPI1_RX_USING_DMA bool "Enable SPI1 RX DMA" depends on BSP_USING_SPI1 select BSP_SPI1_TX_USING_DMA default n config BSP_USING_SPI2 bool "Enable SPI2 BUS" default n config BSP_SPI2_TX_USING_DMA bool "Enable SPI2 TX DMA" depends on BSP_USING_SPI2 default n config BSP_SPI2_RX_USING_DMA bool "Enable SPI2 RX DMA" depends on BSP_USING_SPI2 select BSP_SPI2_TX_USING_DMA default n endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n source "../libraries/HAL_Drivers/Kconfig" endmenu menu "Board extended module Drivers" config BSP_USING_WIFI_OR_GPRS bool "Enable WIFI/GPRS (uart3 be shared)" select BSP_USING_UART3 default n endmenu endmenu