menu "Hardware Drivers Config" config SOC_STM32F469NI bool select SOC_SERIES_STM32F4 select RT_USING_COMPONENTS_INIT select RT_USING_USER_MAIN default y menu "Onboard Peripheral Drivers" config BSP_USING_LVGL bool "Enable LVGL for LCD" select BSP_USING_LCD_OTM8009A select PKG_USING_LVGL select BSP_USING_TOUCH default n if BSP_USING_LVGL config BSP_USING_LVGL_DEMO bool "Enable LVGL demo" select PKG_USING_LV_MUSIC_DEMO default n endif config BSP_USING_ARDUINO bool "Support Arduino" select PKG_USING_RTDUINO select BSP_USING_STLINK_TO_USART select BSP_USING_GPIO select BSP_USING_ADC select BSP_USING_ADC1 select BSP_USING_PWM select BSP_USING_PWM2 select BSP_USING_PWM2_CH2 select BSP_USING_PWM2_CH3 select BSP_USING_PWM3 select BSP_USING_PWM3_CH1 select BSP_USING_PWM3_CH2 select BSP_USING_PWM12 select BSP_USING_PWM12_CH1 select BSP_USING_PWM12_CH2 select BSP_USING_I2C select BSP_USING_I2C1 imply RTDUINO_USING_SERVO imply RTDUINO_USING_WIRE imply RTDUINO_USING_ADAFRUIT imply RTDUINO_USING_MSTIMER2 default n config BSP_USING_SDRAM bool "Enable SDRAM" select BSP_USING_FMC default n config BSP_USING_QSPI_FLASH bool "Enable QSPI FLASH (N25Q128A qspi1)" select BSP_USING_QSPI select RT_USING_SFUD select RT_SFUD_USING_QSPI select RT_USING_FAL select FAL_USING_SFUD_PORT default n config BSP_MOUNT_QSPI_WITH_LFS bool "Mount QSPI flash to / with little fs" depends on BSP_USING_QSPI_FLASH select PKG_USING_LITTLEFS select RT_USING_MTD_NOR select RT_USING_DFS default y config BSP_USING_SDCARD bool "Enable SDCARD (sdio)" select BSP_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT select RT_USING_PIN default n config SDIO_MAX_FREQ int "sdio max freq" range 0 24000000 depends on BSP_USING_SDCARD default 24000000 config BSP_USING_TOUCH bool "Enable touch screen" select BSP_USING_I2C1 select PKG_USING_TOUCH_DRIVERS choice prompt "Touch IC type" depends on BSP_USING_TOUCH default BSP_USING_TOUCH_FT6X36 config BSP_USING_TOUCH_FT6206 bool "FT6206" select PKG_USING_FT6206 config BSP_USING_TOUCH_FT6X36 bool "FT6x36" select PKG_USING_FT6236 endchoice config BSP_USING_LCD_MIPI bool default n config BSP_USING_LCD_OTM8009A bool "Enable LCD OTM8009A" select BSP_USING_SDRAM select BSP_USING_LTDC select BSP_USING_LCD_MIPI default n endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM2 bool "Enable timer2 output PWM" default n if BSP_USING_PWM2 config BSP_USING_PWM2_CH2 bool "Enable PWM2 channel2" default n endif if BSP_USING_PWM2 config BSP_USING_PWM2_CH3 bool "Enable PWM2 channel3" default n endif menuconfig BSP_USING_PWM3 bool "Enable timer3 output PWM" default n if BSP_USING_PWM3 config BSP_USING_PWM3_CH1 bool "Enable PWM3 channel1" default n endif if BSP_USING_PWM3 config BSP_USING_PWM3_CH2 bool "Enable PWM3 channel2" default n endif menuconfig BSP_USING_PWM12 bool "Enable timer12 output PWM" default n if BSP_USING_PWM12 config BSP_USING_PWM12_CH1 bool "Enable PWM12 channel1" default n endif if BSP_USING_PWM12 config BSP_USING_PWM12_CH2 bool "Enable PWM12 channel2" default n endif endif menuconfig BSP_USING_UART bool "Enable UART" select RT_USING_SERIAL default y if BSP_USING_UART config BSP_USING_UART3 bool "Enable UART3" default y config BSP_UART3_RX_USING_DMA bool "Enable UART3 RX DMA" depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA default n endif menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN default n if BSP_USING_I2C1 comment "Notice: PB8 --> 24; PB9 --> 25" config BSP_I2C1_SCL_PIN int "I2C1 scl pin number" range 1 176 default 24 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 1 176 default 25 endif menuconfig BSP_USING_SPI bool "Enable SPI BUS" select RT_USING_SPI default n if BSP_USING_SPI config BSP_USING_SPI3 bool "Enable SPI3 BUS" default n config BSP_SPI3_TX_USING_DMA bool "Enable SPI3 TX DMA" depends on BSP_USING_SPI3 default n config BSP_SPI3_RX_USING_DMA bool "Enable SPI3 RX DMA" depends on BSP_USING_SPI3 select BSP_SPI3_TX_USING_DMA default n endif config BSP_USING_QSPI bool "Enable QSPI BUS" select RT_USING_QSPI select RT_USING_SPI default n config BSP_USING_ON_CHIP_FLASH bool "Enable on-chip FLASH" default n config BSP_USING_FMC bool "Enable FMC" default n config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n config BSP_USING_USBD bool "Enable OTGFS as USB device" select RT_USING_USB_DEVICE default n config BSP_USING_LTDC bool "Enable LTDC" default n source "../libraries/HAL_Drivers/Kconfig" endmenu menu "Board extended module Drivers" endmenu endmenu