menu "Hardware Drivers Config" menu "Onboard Peripheral Drivers" endmenu menu "On-chip Peripheral Drivers" config BSP_USING_GPIO bool "Enable GPIO" select RT_USING_PIN default y menuconfig BSP_USING_XINT bool "Enable external interrupt" default n if BSP_USING_XINT menuconfig BSP_USING_XINT1 bool "Enable XINT1" if BSP_USING_XINT1 config BSP_XINT1_PIN int "Interrupt pin" range 0 168 default 0 endif if !BSP_USING_XINT1 config BSP_XINT1_PIN int default -1 endif menuconfig BSP_USING_XINT2 bool "Enable XINT2" if BSP_USING_XINT2 config BSP_XINT2_PIN int "Interrupt pin" range 0 168 default 0 endif if !BSP_USING_XINT2 config BSP_XINT2_PIN int default -1 endif menuconfig BSP_USING_XINT3 bool "Enable XINT3" if BSP_USING_XINT3 config BSP_XINT3_PIN int "Interrupt pin" range 0 168 default 0 endif if !BSP_USING_XINT3 config BSP_XINT3_PIN int default -1 endif menuconfig BSP_USING_XINT4 bool "Enable XINT4" if BSP_USING_XINT4 config BSP_XINT4_PIN int "Interrupt pin" range 0 168 default 0 endif if !BSP_USING_XINT4 config BSP_XINT4_PIN int default -1 endif if !BSP_USING_XINT5 config BSP_XINT5_PIN int default -1 endif menuconfig BSP_USING_XINT5 bool "Enable XINT5" if BSP_USING_XINT5 config BSP_XINT5_PIN int "Interrupt pin" range 0 168 default 0 endif endif menuconfig BSP_USING_UART bool "Enable UART" default y select RT_USING_SERIAL if BSP_USING_UART config BSP_USING_UART1 bool "Enable UART1" default y endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_PWM1 bool "Enable ePWM1" default n if BSP_USING_PWM1 menu "Basic settings for PWM1" config BSP_PWM1_INIT_PERIOD int "Initial period for PWM1(ns)" default 10000 config BSP_PWM1_INIT_PULSE int "Initial pulse for PWM1(ns)" default 1000 endmenu menu "Advanced Settings for PWM1" menuconfig BSP_PWM1_PHASE_ENABLE bool "Enable phase" default n if BSP_PWM1_PHASE_ENABLE choice prompt "Select master or slave" default BSP_PWM1_MASTER config BSP_PWM1_MASTER bool "Master" config BSP_PWM1_SLAVE bool "Slave" endchoice if BSP_PWM1_MASTER config BSP_PWM1_PHASE int default 0 endif if BSP_PWM1_SLAVE config BSP_PWM1_PHASE int "Phase, 0~360" range 0 360 default 0 help the phase for PWM1 module endif endif menuconfig BSP_PWM1_IT_ENABLE bool "Enable interrupt service" default n if BSP_PWM1_IT_ENABLE choice prompt "Select interrupt time" default BSP_PWM1_INTSEL_ET_CTR_ZERO config BSP_PWM1_INTSEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM1_INTSEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM1_INTSEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM1_INTSEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM1_INTSEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM1_INTSEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM1_INTSEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM1_INTSEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM1_INTSEL int default 0 if BSP_PWM1_INTSEL_ET_DCAEVT1SOC default 1 if BSP_PWM1_INTSEL_ET_CTR_ZERO default 2 if BSP_PWM1_INTSEL_ET_CTR_PRD default 3 if BSP_PWM1_INTSEL_ET_CTR_PRDZERO default 4 if BSP_PWM1_INTSEL_ET_CTRU_CMPA default 5 if BSP_PWM1_INTSEL_ET_CTRD_CMPA default 6 if BSP_PWM1_INTSEL_ET_CTRU_CMPB default 7 if BSP_PWM1_INTSEL_ET_CTRD_CMPB choice prompt "Interrupt generation time" default BSP_PWM1_INT_ET_1ST config BSP_PWM1_INT_ET_DISABLE bool "disable PWM interrupt" config BSP_PWM1_INT_ET_1ST bool "generate interrupt at the first time" config BSP_PWM1_INT_ET_2ND bool "generate interrupt at the second time" config BSP_PWM1_INT_ET_3RD bool "generate interrupt at the third time" endchoice config BSP_PWM1_INTPRD int default 0 if BSP_PWM1_INT_ET_DISABLE default 1 if BSP_PWM1_INT_ET_1ST default 2 if BSP_PWM1_INT_ET_2ND default 3 if BSP_PWM1_INT_ET_3RD endif choice prompt "HSP Clock division" default BSP_PWM1_HSPCLKDIV1 config BSP_PWM1_HSPCLKDIV1 bool "Clock Divided by 1" config BSP_PWM1_HSPCLKDIV2 bool "Clock Divided by 2" config BSP_PWM1_HSPCLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM1_HSPCLKDIV int default 0 if BSP_PWM1_HSPCLKDIV1 default 1 if BSP_PWM1_HSPCLKDIV2 default 2 if BSP_PWM1_HSPCLKDIV4 choice prompt "Clock division" default BSP_PWM1_CLKDIV1 config BSP_PWM1_CLKDIV1 bool "Clock Divided by 1" config BSP_PWM1_CLKDIV2 bool "Clock Divided by 2" config BSP_PWM1_CLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM1_CLKDIV int default 0 if BSP_PWM1_CLKDIV1 default 1 if BSP_PWM1_CLKDIV2 default 2 if BSP_PWM1_CLKDIV4 choice default BSP_PWM1_CTR_MODE_UPDOWN prompt "Select counter mode" config BSP_PWM1_CTR_MODE_UPDOWN bool "Up-down mode" config BSP_PWM1_CTR_MODE_UP bool "Up mode" config BSP_PWM1_CTR_MODE_DOWN bool "Down mode" config BSP_PWM1_CTR_FREEZE bool "Freezing Counter" endchoice config BSP_PWM1_CTRMODE int default 0 if BSP_PWM1_CTR_MODE_UP default 1 if BSP_PWM1_CTR_MODE_DOWN default 2 if BSP_PWM1_CTR_MODE_UPDOWN default 3 if BSP_PWM1_CTR_FREEZE choice prompt "Register load mode" config BSP_PWM1_CC_CTR_ZERO bool "Load when counter == 0" config BSP_PWM1_CC_CTR_PRD bool "Load when counter == prd" config BSP_PWM1_CC_CTR_ZERO_PRD bool "load when counter ==0 or counter == prd" config BSP_PWM1_CC_LD_DISABLE bool "disable load" endchoice config BSP_PWM1_LOADAMODE int default 0 if BSP_PWM1_CC_CTR_ZERO default 1 if BSP_PWM1_CC_CTR_PRD default 2 if BSP_PWM1_CC_CTR_ZERO_PRD default 3 if BSP_PWM1_CC_LD_DISABLE config BSP_PWM1_DB int "Dead time(ns)" default 100 range 0 100000 menuconfig BSP_PWM1_ADC_TRIGGER bool "Enable ADC trigger from PWM1" if BSP_PWM1_ADC_TRIGGER choice prompt "Select soc triggering time" default BSP_PWM1_SOCASEL_ET_CTR_ZERO config BSP_PWM1_SOCASEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM1_SOCASEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM1_SOCASEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM1_SOCASEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM1_SOCASEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM1_SOCASEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM1_SOCASEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM1_SOCASEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM1_SOCASEL int default 0 if BSP_PWM1_SOCASEL_ET_DCAEVT1SOC default 1 if BSP_PWM1_SOCASEL_ET_CTR_ZERO default 2 if BSP_PWM1_SOCASEL_ET_CTR_PRD default 3 if BSP_PWM1_SOCASEL_ET_CTR_PRDZERO default 4 if BSP_PWM1_SOCASEL_ET_CTRU_CMPA default 5 if BSP_PWM1_SOCASEL_ET_CTRD_CMPA default 6 if BSP_PWM1_SOCASEL_ET_CTRU_CMPB default 7 if BSP_PWM1_SOCASEL_ET_CTRD_CMPB choice prompt "SOCA generation time" default BSP_PWM1_SOCA_ET_1ST config BSP_PWM1_SOCA_ET_DISABLE bool "disable soc generation" config BSP_PWM1_SOCA_ET_1ST bool "generate soc at the first time" config BSP_PWM1_SOCA_ET_2ND bool "generate soc at the second time" config BSP_PWM1_SOCA_ET_3RD bool "generate soc at the third time" endchoice config BSP_PWM1_SOCAPRD int default 0 if BSP_PWM1_SOCA_ET_DISABLE default 1 if BSP_PWM1_SOCA_ET_1ST default 2 if BSP_PWM1_SOCA_ET_2ND default 3 if BSP_PWM1_SOCA_ET_3RD endif endmenu endif menuconfig BSP_USING_PWM2 bool "Enable ePWM2" default n if BSP_USING_PWM2 menu "Basic settings for PWM2" config BSP_PWM2_INIT_PERIOD int "Initial period for PWM2(ns)" default 10000 config BSP_PWM2_INIT_PULSE int "Initial pulse for PWM2(ns)" default 1000 endmenu menu "Advanced Settings for PWM2" menuconfig BSP_PWM2_PHASE_ENABLE bool "Enable phase" default n if BSP_PWM2_PHASE_ENABLE choice prompt "Select master or slave" default BSP_PWM2_SLAVE config BSP_PWM2_MASTER bool "Master" config BSP_PWM2_SLAVE bool "Slave" endchoice if BSP_PWM2_MASTER config BSP_PWM2_PHASE int default 0 endif if BSP_PWM2_SLAVE config BSP_PWM2_PHASE int "Phase, 0~360" range 0 360 default 0 help the phase for PWM2 module endif endif menuconfig BSP_PWM2_IT_ENABLE bool "Enable interrupt service" default n if BSP_PWM2_IT_ENABLE choice prompt "Select interrupt time" default BSP_PWM2_INTSEL_ET_CTR_ZERO config BSP_PWM2_INTSEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM2_INTSEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM2_INTSEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM2_INTSEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM2_INTSEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM2_INTSEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM2_INTSEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM2_INTSEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM2_INTSEL int default 0 if BSP_PWM2_INTSEL_ET_DCAEVT1SOC default 1 if BSP_PWM2_INTSEL_ET_CTR_ZERO default 2 if BSP_PWM2_INTSEL_ET_CTR_PRD default 3 if BSP_PWM2_INTSEL_ET_CTR_PRDZERO default 4 if BSP_PWM2_INTSEL_ET_CTRU_CMPA default 5 if BSP_PWM2_INTSEL_ET_CTRD_CMPA default 6 if BSP_PWM2_INTSEL_ET_CTRU_CMPB default 7 if BSP_PWM2_INTSEL_ET_CTRD_CMPB choice prompt "Interrupt generation time" default BSP_PWM2_INT_ET_1ST config BSP_PWM2_INT_ET_DISABLE bool "disable PWM interrupt" config BSP_PWM2_INT_ET_1ST bool "generate interrupt at the first time" config BSP_PWM2_INT_ET_2ND bool "generate interrupt at the second time" config BSP_PWM2_INT_ET_3RD bool "generate interrupt at the third time" endchoice config BSP_PWM2_INTPRD int default 0 if BSP_PWM2_INT_ET_DISABLE default 1 if BSP_PWM2_INT_ET_1ST default 2 if BSP_PWM2_INT_ET_2ND default 3 if BSP_PWM2_INT_ET_3RD endif choice prompt "HSP Clock division" default BSP_PWM2_HSPCLKDIV1 config BSP_PWM2_HSPCLKDIV1 bool "Clock Divided by 1" config BSP_PWM2_HSPCLKDIV2 bool "Clock Divided by 2" config BSP_PWM2_HSPCLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM2_HSPCLKDIV int default 0 if BSP_PWM2_HSPCLKDIV1 default 1 if BSP_PWM2_HSPCLKDIV2 default 2 if BSP_PWM2_HSPCLKDIV4 choice prompt "Clock division" default BSP_PWM2_CLKDIV1 config BSP_PWM2_CLKDIV1 bool "Clock Divided by 1" config BSP_PWM2_CLKDIV2 bool "Clock Divided by 2" config BSP_PWM2_CLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM2_CLKDIV int default 0 if BSP_PWM2_CLKDIV1 default 1 if BSP_PWM2_CLKDIV2 default 2 if BSP_PWM2_CLKDIV4 choice default BSP_PWM2_CTR_MODE_UPDOWN prompt "Select counter mode" config BSP_PWM2_CTR_MODE_UPDOWN bool "Up-down mode" config BSP_PWM2_CTR_MODE_UP bool "Up mode" config BSP_PWM2_CTR_MODE_DOWN bool "Down mode" config BSP_PWM2_CTR_FREEZE bool "Freezing Counter" endchoice config BSP_PWM2_CTRMODE int default 0 if BSP_PWM2_CTR_MODE_UP default 1 if BSP_PWM2_CTR_MODE_DOWN default 2 if BSP_PWM2_CTR_MODE_UPDOWN default 3 if BSP_PWM2_CTR_FREEZE choice prompt "Register load mode" config BSP_PWM2_CC_CTR_ZERO bool "Load when counter == 0" config BSP_PWM2_CC_CTR_PRD bool "Load when counter == prd" config BSP_PWM2_CC_CTR_ZERO_PRD bool "load when counter ==0 or counter == prd" config BSP_PWM2_CC_LD_DISABLE bool "disable load" endchoice config BSP_PWM2_LOADAMODE int default 0 if BSP_PWM2_CC_CTR_ZERO default 1 if BSP_PWM2_CC_CTR_PRD default 2 if BSP_PWM2_CC_CTR_ZERO_PRD default 3 if BSP_PWM2_CC_LD_DISABLE config BSP_PWM2_DB int "Dead time(ns)" default 100 range 0 100000 menuconfig BSP_PWM2_ADC_TRIGGER bool "Enable ADC trigger from PWM2" if BSP_PWM2_ADC_TRIGGER choice prompt "Select soc triggering time" default BSP_PWM2_SOCASEL_ET_CTR_ZERO config BSP_PWM2_SOCASEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM2_SOCASEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM2_SOCASEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM2_SOCASEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM2_SOCASEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM2_SOCASEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM2_SOCASEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM2_SOCASEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM2_SOCASEL int default 0 if BSP_PWM2_SOCASEL_ET_DCAEVT1SOC default 1 if BSP_PWM2_SOCASEL_ET_CTR_ZERO default 2 if BSP_PWM2_SOCASEL_ET_CTR_PRD default 3 if BSP_PWM2_SOCASEL_ET_CTR_PRDZERO default 4 if BSP_PWM2_SOCASEL_ET_CTRU_CMPA default 5 if BSP_PWM2_SOCASEL_ET_CTRD_CMPA default 6 if BSP_PWM2_SOCASEL_ET_CTRU_CMPB default 7 if BSP_PWM2_SOCASEL_ET_CTRD_CMPB choice prompt "SOCA generation time" default BSP_PWM2_SOCA_ET_1ST config BSP_PWM2_SOCA_ET_DISABLE bool "disable soc generation" config BSP_PWM2_SOCA_ET_1ST bool "generate soc at the first time" config BSP_PWM2_SOCA_ET_2ND bool "generate soc at the second time" config BSP_PWM2_SOCA_ET_3RD bool "generate soc at the third time" endchoice config BSP_PWM2_SOCAPRD int default 0 if BSP_PWM2_SOCA_ET_DISABLE default 1 if BSP_PWM2_SOCA_ET_1ST default 2 if BSP_PWM2_SOCA_ET_2ND default 3 if BSP_PWM2_SOCA_ET_3RD endif endmenu endif menuconfig BSP_USING_PWM3 bool "Enable ePWM3" default n if BSP_USING_PWM3 menu "Basic settings for PWM3" config BSP_PWM3_INIT_PERIOD int "Initial period for PWM3(ns)" default 10000 config BSP_PWM3_INIT_PULSE int "Initial pulse for PWM3(ns)" default 1000 endmenu menu "Advanced Settings for PWM3" menuconfig BSP_PWM3_PHASE_ENABLE bool "Enable phase" default n if BSP_PWM3_PHASE_ENABLE choice prompt "Select master or slave" default BSP_PWM3_SLAVE config BSP_PWM3_MASTER bool "Master" config BSP_PWM3_SLAVE bool "Slave" endchoice if BSP_PWM3_MASTER config BSP_PWM3_PHASE int default 0 endif if BSP_PWM3_SLAVE config BSP_PWM3_PHASE int "Phase, 0~360" range 0 360 default 0 help the phase for PWM3 module endif endif menuconfig BSP_PWM3_IT_ENABLE bool "Enable interrupt service" default n if BSP_PWM3_IT_ENABLE choice prompt "Select interrupt time" default BSP_PWM3_INTSEL_ET_CTR_ZERO config BSP_PWM3_INTSEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM3_INTSEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM3_INTSEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM3_INTSEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM3_INTSEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM3_INTSEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM3_INTSEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM3_INTSEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM3_INTSEL int default 0 if BSP_PWM3_INTSEL_ET_DCAEVT1SOC default 1 if BSP_PWM3_INTSEL_ET_CTR_ZERO default 2 if BSP_PWM3_INTSEL_ET_CTR_PRD default 3 if BSP_PWM3_INTSEL_ET_CTR_PRDZERO default 4 if BSP_PWM3_INTSEL_ET_CTRU_CMPA default 5 if BSP_PWM3_INTSEL_ET_CTRD_CMPA default 6 if BSP_PWM3_INTSEL_ET_CTRU_CMPB default 7 if BSP_PWM3_INTSEL_ET_CTRD_CMPB choice prompt "Interrupt generation time" default BSP_PWM3_INT_ET_1ST config BSP_PWM3_INT_ET_DISABLE bool "disable PWM interrupt" config BSP_PWM3_INT_ET_1ST bool "generate interrupt at the first time" config BSP_PWM3_INT_ET_2ND bool "generate interrupt at the second time" config BSP_PWM3_INT_ET_3RD bool "generate interrupt at the third time" endchoice config BSP_PWM3_INTPRD int default 0 if BSP_PWM3_INT_ET_DISABLE default 1 if BSP_PWM3_INT_ET_1ST default 2 if BSP_PWM3_INT_ET_2ND default 3 if BSP_PWM3_INT_ET_3RD endif choice prompt "HSP Clock division" default BSP_PWM3_HSPCLKDIV1 config BSP_PWM3_HSPCLKDIV1 bool "Clock Divided by 1" config BSP_PWM3_HSPCLKDIV2 bool "Clock Divided by 2" config BSP_PWM3_HSPCLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM3_HSPCLKDIV int default 0 if BSP_PWM3_HSPCLKDIV1 default 1 if BSP_PWM3_HSPCLKDIV2 default 2 if BSP_PWM3_HSPCLKDIV4 choice prompt "Clock division" default BSP_PWM3_CLKDIV1 config BSP_PWM3_CLKDIV1 bool "Clock Divided by 1" config BSP_PWM3_CLKDIV2 bool "Clock Divided by 2" config BSP_PWM3_CLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM3_CLKDIV int default 0 if BSP_PWM3_CLKDIV1 default 1 if BSP_PWM3_CLKDIV2 default 2 if BSP_PWM3_CLKDIV4 choice default BSP_PWM3_CTR_MODE_UPDOWN prompt "Select counter mode" config BSP_PWM3_CTR_MODE_UPDOWN bool "Up-down mode" config BSP_PWM3_CTR_MODE_UP bool "Up mode" config BSP_PWM3_CTR_MODE_DOWN bool "Down mode" config BSP_PWM3_CTR_FREEZE bool "Freezing Counter" endchoice config BSP_PWM3_CTRMODE int default 0 if BSP_PWM3_CTR_MODE_UP default 1 if BSP_PWM3_CTR_MODE_DOWN default 2 if BSP_PWM3_CTR_MODE_UPDOWN default 3 if BSP_PWM3_CTR_FREEZE choice prompt "Register load mode" config BSP_PWM3_CC_CTR_ZERO bool "Load when counter == 0" config BSP_PWM3_CC_CTR_PRD bool "Load when counter == prd" config BSP_PWM3_CC_CTR_ZERO_PRD bool "load when counter ==0 or counter == prd" config BSP_PWM3_CC_LD_DISABLE bool "disable load" endchoice config BSP_PWM3_LOADAMODE int default 0 if BSP_PWM3_CC_CTR_ZERO default 1 if BSP_PWM3_CC_CTR_PRD default 2 if BSP_PWM3_CC_CTR_ZERO_PRD default 3 if BSP_PWM3_CC_LD_DISABLE config BSP_PWM3_DB int "Dead time(ns)" default 100 range 0 100000 menuconfig BSP_PWM3_ADC_TRIGGER bool "Enable ADC trigger from PWM3" if BSP_PWM3_ADC_TRIGGER choice prompt "Select soc triggering time" default BSP_PWM3_SOCASEL_ET_CTR_ZERO config BSP_PWM3_SOCASEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM3_SOCASEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM3_SOCASEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM3_SOCASEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM3_SOCASEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM3_SOCASEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM3_SOCASEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM3_SOCASEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM3_SOCASEL int default 0 if BSP_PWM3_SOCASEL_ET_DCAEVT1SOC default 1 if BSP_PWM3_SOCASEL_ET_CTR_ZERO default 2 if BSP_PWM3_SOCASEL_ET_CTR_PRD default 3 if BSP_PWM3_SOCASEL_ET_CTR_PRDZERO default 4 if BSP_PWM3_SOCASEL_ET_CTRU_CMPA default 5 if BSP_PWM3_SOCASEL_ET_CTRD_CMPA default 6 if BSP_PWM3_SOCASEL_ET_CTRU_CMPB default 7 if BSP_PWM3_SOCASEL_ET_CTRD_CMPB choice prompt "SOCA generation time" default BSP_PWM3_SOCA_ET_1ST config BSP_PWM3_SOCA_ET_DISABLE bool "disable soc generation" config BSP_PWM3_SOCA_ET_1ST bool "generate soc at the first time" config BSP_PWM3_SOCA_ET_2ND bool "generate soc at the second time" config BSP_PWM3_SOCA_ET_3RD bool "generate soc at the third time" endchoice config BSP_PWM3_SOCAPRD int default 0 if BSP_PWM3_SOCA_ET_DISABLE default 1 if BSP_PWM3_SOCA_ET_1ST default 2 if BSP_PWM3_SOCA_ET_2ND default 3 if BSP_PWM3_SOCA_ET_3RD endif endmenu endif menuconfig BSP_USING_PWM4 bool "Enable ePWM4" default n if BSP_USING_PWM4 menu "Basic settings for PWM4" config BSP_PWM4_INIT_PERIOD int "Initial period for PWM4(ns)" default 10000 config BSP_PWM4_INIT_PULSE int "Initial pulse for PWM4(ns)" default 1000 endmenu menu "Advanced Settings for PWM4" menuconfig BSP_PWM4_PHASE_ENABLE bool "Enable phase" default n if BSP_PWM4_PHASE_ENABLE choice prompt "Select master or slave" default BSP_PWM4_SLAVE config BSP_PWM4_MASTER bool "Master" config BSP_PWM4_SLAVE bool "Slave" endchoice if BSP_PWM4_MASTER config BSP_PWM4_PHASE int default 0 endif if BSP_PWM4_SLAVE config BSP_PWM4_PHASE int "Phase, 0~360" range 0 360 default 0 help the phase for PWM4 module endif endif menuconfig BSP_PWM4_IT_ENABLE bool "Enable interrupt service" default n if BSP_PWM4_IT_ENABLE choice prompt "Select interrupt time" default BSP_PWM4_INTSEL_ET_CTR_ZERO config BSP_PWM4_INTSEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM4_INTSEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM4_INTSEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM4_INTSEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM4_INTSEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM4_INTSEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM4_INTSEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM4_INTSEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM4_INTSEL int default 0 if BSP_PWM4_INTSEL_ET_DCAEVT1SOC default 1 if BSP_PWM4_INTSEL_ET_CTR_ZERO default 2 if BSP_PWM4_INTSEL_ET_CTR_PRD default 3 if BSP_PWM4_INTSEL_ET_CTR_PRDZERO default 4 if BSP_PWM4_INTSEL_ET_CTRU_CMPA default 5 if BSP_PWM4_INTSEL_ET_CTRD_CMPA default 6 if BSP_PWM4_INTSEL_ET_CTRU_CMPB default 7 if BSP_PWM4_INTSEL_ET_CTRD_CMPB choice prompt "Interrupt generation time" default BSP_PWM4_INT_ET_1ST config BSP_PWM4_INT_ET_DISABLE bool "disable PWM interrupt" config BSP_PWM4_INT_ET_1ST bool "generate interrupt at the first time" config BSP_PWM4_INT_ET_2ND bool "generate interrupt at the second time" config BSP_PWM4_INT_ET_3RD bool "generate interrupt at the third time" endchoice config BSP_PWM4_INTPRD int default 0 if BSP_PWM4_INT_ET_DISABLE default 1 if BSP_PWM4_INT_ET_1ST default 2 if BSP_PWM4_INT_ET_2ND default 3 if BSP_PWM4_INT_ET_3RD endif choice prompt "HSP Clock division" default BSP_PWM4_HSPCLKDIV1 config BSP_PWM4_HSPCLKDIV1 bool "Clock Divided by 1" config BSP_PWM4_HSPCLKDIV2 bool "Clock Divided by 2" config BSP_PWM4_HSPCLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM4_HSPCLKDIV int default 0 if BSP_PWM4_HSPCLKDIV1 default 1 if BSP_PWM4_HSPCLKDIV2 default 2 if BSP_PWM4_HSPCLKDIV4 choice prompt "Clock division" default BSP_PWM4_CLKDIV1 config BSP_PWM4_CLKDIV1 bool "Clock Divided by 1" config BSP_PWM4_CLKDIV2 bool "Clock Divided by 2" config BSP_PWM4_CLKDIV4 bool "Clock Divided by 4" endchoice config BSP_PWM4_CLKDIV int default 0 if BSP_PWM4_CLKDIV1 default 1 if BSP_PWM4_CLKDIV2 default 2 if BSP_PWM4_CLKDIV4 choice default BSP_PWM4_CTR_MODE_UPDOWN prompt "Select counter mode" config BSP_PWM4_CTR_MODE_UPDOWN bool "Up-down mode" config BSP_PWM4_CTR_MODE_UP bool "Up mode" config BSP_PWM4_CTR_MODE_DOWN bool "Down mode" config BSP_PWM4_CTR_FREEZE bool "Freezing Counter" endchoice config BSP_PWM4_CTRMODE int default 0 if BSP_PWM4_CTR_MODE_UP default 1 if BSP_PWM4_CTR_MODE_DOWN default 2 if BSP_PWM4_CTR_MODE_UPDOWN default 3 if BSP_PWM4_CTR_FREEZE choice prompt "Register load mode" config BSP_PWM4_CC_CTR_ZERO bool "Load when counter == 0" config BSP_PWM4_CC_CTR_PRD bool "Load when counter == prd" config BSP_PWM4_CC_CTR_ZERO_PRD bool "load when counter ==0 or counter == prd" config BSP_PWM4_CC_LD_DISABLE bool "disable load" endchoice config BSP_PWM4_LOADAMODE int default 0 if BSP_PWM4_CC_CTR_ZERO default 1 if BSP_PWM4_CC_CTR_PRD default 2 if BSP_PWM4_CC_CTR_ZERO_PRD default 3 if BSP_PWM4_CC_LD_DISABLE config BSP_PWM4_DB int "Dead time(ns)" default 100 range 0 100000 menuconfig BSP_PWM4_ADC_TRIGGER bool "Enable ADC trigger from PWM4" if BSP_PWM4_ADC_TRIGGER choice prompt "Select soc triggering time" default BSP_PWM4_SOCASEL_ET_CTR_ZERO config BSP_PWM4_SOCASEL_ET_DCAEVT1SOC bool "DCAEVT1SOC" config BSP_PWM4_SOCASEL_ET_CTR_ZERO bool "ctr == zero" config BSP_PWM4_SOCASEL_ET_CTR_PRD bool "ctr == prd" config BSP_PWM4_SOCASEL_ET_CTR_PRDZERO bool "ctr == prd or ctr == zero" config BSP_PWM4_SOCASEL_ET_CTRU_CMPA bool "ctr == compa when counting up" config BSP_PWM4_SOCASEL_ET_CTRD_CMPA bool "ctr == compa when counting down" config BSP_PWM4_SOCASEL_ET_CTRU_CMPB bool "ctr == compb when counting up" config BSP_PWM4_SOCASEL_ET_CTRD_CMPB bool "ctr == compb when counting down" endchoice config BSP_PWM4_SOCASEL int default 0 if BSP_PWM4_SOCASEL_ET_DCAEVT1SOC default 1 if BSP_PWM4_SOCASEL_ET_CTR_ZERO default 2 if BSP_PWM4_SOCASEL_ET_CTR_PRD default 3 if BSP_PWM4_SOCASEL_ET_CTR_PRDZERO default 4 if BSP_PWM4_SOCASEL_ET_CTRU_CMPA default 5 if BSP_PWM4_SOCASEL_ET_CTRD_CMPA default 6 if BSP_PWM4_SOCASEL_ET_CTRU_CMPB default 7 if BSP_PWM4_SOCASEL_ET_CTRD_CMPB choice prompt "SOCA generation time" default BSP_PWM4_SOCA_ET_1ST config BSP_PWM4_SOCA_ET_DISABLE bool "disable soc generation" config BSP_PWM4_SOCA_ET_1ST bool "generate soc at the first time" config BSP_PWM4_SOCA_ET_2ND bool "generate soc at the second time" config BSP_PWM4_SOCA_ET_3RD bool "generate soc at the third time" endchoice config BSP_PWM4_SOCAPRD int default 0 if BSP_PWM4_SOCA_ET_DISABLE default 1 if BSP_PWM4_SOCA_ET_1ST default 2 if BSP_PWM4_SOCA_ET_2ND default 3 if BSP_PWM4_SOCA_ET_3RD endif endmenu endif endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC1 bool "Enable ADC1" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC default n if BSP_USING_ONCHIP_RTC choice prompt "Select clock source" default BSP_RTC_USING_LSE config BSP_RTC_USING_LSE bool "RTC USING LSE" config BSP_RTC_USING_LSI bool "RTC USING LSI" endchoice endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS default n menuconfig BSP_USING_CAN bool "Enable CAN" default n select RT_USING_CAN if BSP_USING_CAN config BSP_USING_CAN1 bool "using CAN1" default n endif config BSP_USING_USBD bool "Enable USB device" select RT_USING_USB_DEVICE default n if BSP_USING_USBD config BSP_USB_CONNECT_PIN int "USB connect pin" default 67 config BSP_USB_PULL_UP_STATUS int "USB PULL UP STATUS" default 0 endif endmenu menu "Board extended module Drivers" endmenu endmenu