menu "Hardware Drivers Config" config SOC_AB32VG1 bool select PKG_USING_BLUETRUM_SDK default y menu "Onboard Peripheral Drivers" menuconfig BSP_USING_AUDIO bool "Enable Audio Device" select RT_USING_AUDIO default n if BSP_USING_AUDIO config BSP_USING_AUDIO_PLAY bool "Enable Audio Play" default y endif config BSP_USING_SDCARD bool "Enable SDCARD" select BSP_USING_SDIO default n if BSP_USING_SDCARD config SDIO_MAX_FREQ int "sdio max freq" range 0 24000000 default 24000000 endif endmenu menu "On-chip Peripheral Drivers" menuconfig BSP_USING_UART bool "Enable UART" if BSP_USING_UART config BSP_USING_UART0 bool "Enable UART0" select RT_USING_SERIAL default y if BSP_USING_UART0 config BSP_UART0_FIFO_SIZE int "BSP_UART0_FIFO_SIZE" range 5 255 default 10 endif config BSP_USING_UART1 bool "Enable UART1" select RT_USING_SERIAL default n if BSP_USING_UART1 config BSP_UART1_FIFO_SIZE int "BSP_UART1_FIFO_SIZE" range 5 255 default 10 endif config BSP_USING_UART2 bool "Enable UART2" select RT_USING_SERIAL default n if BSP_USING_UART2 config BSP_UART2_FIFO_SIZE int "BSP_UART2_FIFO_SIZE" range 5 255 default 10 endif endif config BSP_USING_SDIO bool "Enable SDIO" select RT_USING_SDIO select RT_USING_DFS select RT_USING_DFS_ELMFAT default n menuconfig BSP_USING_I2C1 bool "Enable I2C1 BUS (software simulation)" default n select RT_USING_I2C select RT_USING_I2C_BITOPS select RT_USING_PIN if BSP_USING_I2C1 comment "Notice: PE3 --> 16; PE2 --> 15" config BSP_I2C1_SCL_PIN int "I2C1 scl pin number" range 1 27 default 16 config BSP_I2C1_SDA_PIN int "I2C1 sda pin number" range 1 27 default 15 endif menuconfig BSP_USING_PWM bool "Enable PWM" default n select RT_USING_PWM if BSP_USING_PWM menuconfig BSP_USING_T3_PWM bool "Enable Timer3 PWM" default n if BSP_USING_T3_PWM config BSP_USING_T3_PWM0 bool "Enable Timer3 PWM0 (PB0)(Confict with SD card)" default n endif menuconfig BSP_USING_T4_PWM bool "Enable Timer4 PWM" default n if BSP_USING_T4_PWM config BSP_USING_T4_PWM1 bool "Enable Timer4 PWM1 (PA6)(Confit with uart0 rx)" default y endif menuconfig BSP_USING_T5_PWM bool "Enable Timer5 PWM" default y if BSP_USING_T5_PWM config BSP_USING_T5_PWM0 bool "Enable Timer5 PWM2 (PE1)" default y endif menuconfig BSP_USING_LPWM0 bool "Enable LPWM0" default n if BSP_USING_LPWM0 comment "G1, G2 and G3 are mutually exclusive" config BSP_USING_LPWM0_G1 bool "Enable LPWM0 G1 (PE4)" default y endif menuconfig BSP_USING_LPWM1 bool "Enable LPWM1" default n if BSP_USING_LPWM1 comment "G1, G2 and G3 are mutually exclusive" config BSP_USING_LPWM1_G3 bool "Enable LPWM1 G3 (PA1)" default y endif menuconfig BSP_USING_LPWM2 bool "Enable LPWM2" default n if BSP_USING_LPWM2 comment "G1, G2 and G3 are mutually exclusive" config BSP_USING_LPWM2_G2 bool "Enable LPWM2 G2 (PE0)" default y config BSP_USING_LPWM2_G3 bool "Enable LPWM2 G3 (PA2)" default n endif endif config BSP_USING_WDT bool "Enable Watchdog Timer" select RT_USING_WDT default n menuconfig BSP_USING_TIM bool "Enable timer" default n select RT_USING_HWTIMER if BSP_USING_TIM config BSP_USING_TIM1 bool "Enable TIM1" default y config BSP_USING_TIM2 bool "Enable TIM2" default n config BSP_USING_TIM3 bool "Enable TIM3" default n config BSP_USING_TIM4 bool "Enable TIM4" default n config BSP_USING_TIM5 bool "Enable TIM5" default n endif menuconfig BSP_USING_ONCHIP_RTC bool "Enable RTC" select RT_USING_RTC select RT_USING_LIBC default n if BSP_USING_ONCHIP_RTC config RTC_USING_INTERNAL_CLK bool "Using internal clock RTC" default y config RTC_USING_1S_INT bool "Using 1 second interrupt" depends on RT_USING_ALARM default n endif menuconfig BSP_USING_ADC bool "Enable ADC" default n select RT_USING_ADC if BSP_USING_ADC config BSP_USING_ADC0 bool "Enable ADC0" default y endif menuconfig BSP_USING_IRRX bool "Enable IRRX(HW or SW)" default n if BSP_USING_IRRX config BSP_USING_IRRX_HW bool "Enable hardware IRRX" default y config BSP_USING_IRRX_SW bool "Enable software IRRX" default n endif endmenu menu "Board extended module Drivers" endmenu endmenu