menu "Hardware Drivers Config"

config SOC_LPC55S6X
    bool 
    select SOC_LPC55S6X_SERIES
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_DMA
        bool "Enable DMA"
        select RT_USING_DMA
        default n
    
    config BSP_USING_PIN
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_UART
        config BSP_USING_UART
            bool "Enable UART"
            select RT_USING_UART
            default y
            
            if BSP_USING_UART
                config BSP_USING_UART0
                    bool "Enable Flexcomm0 as UART"
                    default y
                    if BSP_USING_UART0
                        choice
                            prompt "Select UART0 badurate"
                            default HW_UART0_BAUDRATE_115200

                            config HW_UART0_BAUDRATE_9600
                                bool "Badurate 9600"

                            config HW_UART0_BAUDRATE_115200
                                bool "Badurate 115200"
                        endchoice
                    endif

                config BSP_USING_UART2
                    bool "Enable Flexcomm2 as UART"
                    default n
                    if BSP_USING_UART2
                        choice
                            prompt "Select UART2 badurate"
                            default HW_UART2_BAUDRATE_115200

                            config HW_UART2_BAUDRATE_9600
                                bool "Badurate 9600"

                            config HW_UART2_BAUDRATE_115200
                                bool "Badurate 115200"   
                        endchoice
                    endif 
            endif


    menuconfig BSP_USING_I2C
        config BSP_USING_I2C
            bool "Enable I2C"
            select RT_USING_I2C
            default y

            if BSP_USING_I2C
                config BSP_USING_I2C1
                    bool "Enable Flexcomm1 I2C"
                    default y
                    if BSP_USING_I2C1
                        choice
                            prompt "Select I2C1 badurate"
                            default HW_I2C1_BAUDRATE_100kHZ

                            config HW_I2C1_BAUDRATE_100kHZ
                                bool "Badurate 100kHZ"

                            config HW_I2C1_BAUDRATE_400kHZ
                                bool "Badurate 400kHZ"
                        endchoice
                    endif

                config BSP_USING_I2C4
                    bool "Enable Flexcomm4 I2C"
                    default y
                    if BSP_USING_I2C4
                        choice
                            prompt "Select I2C4 badurate"
                            default HW_I2C4_BAUDRATE_100kHZ

                            config HW_I2C4_BAUDRATE_100kHZ
                                bool "Badurate 100kHZ"

                            config HW_I2C4_BAUDRATE_400kHZ
                                bool "Badurate 400kHZ"
                        endchoice
                    endif
            endif

    menuconfig BSP_USING_SPI
        config BSP_USING_SPI
            bool "Enable SPI"
            select RT_USING_SPI
            default y
            
            if BSP_USING_SPI
                config BSP_USING_SPI3
                    bool "Enable Flexcomm3 as SPI"
                    default n

                config BSP_USING_SPI8
                    bool "Enable Flexcomm8 as High Speed SPI"
                    default y
            endif

    menuconfig BSP_USING_ADC
        config BSP_USING_ADC
            bool "Enable ADC Channel"
            select RT_USING_ADC
            default y
            
            if BSP_USING_ADC
                config BSP_USING_ADC0_CH0
                    bool "Enable ADC0 Channel0"
                    default y

                config BSP_USING_ADC0_CH1
                    bool "Enable ADC0 Channel1"
                    default n
            endif

    config BSP_USING_SDIO
        bool "Enable SDIO SD Card Interface"
        select RT_USING_SDIO
        default y

    config BSP_USING_RTC
        bool "Enable RTC"
        select RT_USING_RTC
        default y

    config BSP_USING_WDT
        bool "Enable WatchDog"
        select RT_USING_WDT
        default n

    menuconfig BSP_USING_HWTIMER
        config BSP_USING_HWTIMER
            bool "Enable Timer"
            select RT_USING_HWTIMER
            default y

            if BSP_USING_HWTIMER
                config BSP_USING_CTIMER0
                    bool "Enable CIMER0"
                    default y

                config BSP_USING_CTIMER1
                    bool "Enable CIMER1"
                    default n

                config BSP_USING_CTIMER3
                    bool "Enable CIMER3"
                    default n

                config BSP_USING_CTIMER4
                    bool "Enable CIMER4"
                    default n
            endif

    menuconfig BSP_USING_PWM
        config BSP_USING_PWM
            bool "Enable PWM"
            select RT_USING_PWM
            default y

            if BSP_USING_PWM
                config BSP_USING_CTIMER2_MAT0
                    bool "Enable CIMER2 Match0 as PWM output"
                    default y

                config BSP_USING_CTIMER2_MAT1
                    bool "Enable CIMER2 Match1 as PWM output"
                    default n

                config BSP_USING_CTIMER2_MAT2
                    bool "Enable CIMER2 Match2 as PWM output"
                    default n
            endif
endmenu

menu "Onboard Peripheral Drivers"
    config BSP_USING_LED
        bool "Enable RGB LED"
        select RT_USING_LED
        default y

    config BSP_USING_KEY
        bool "Enable Button "
        select RT_USING_KEY
        default y

    config BSP_USING_MMA8562
        bool "Enable MMA8562"
        select BSP_USING_I2C4
        default y
        if BSP_USING_MMA8562
            config BSP_USING_MMA8562I2C
                string "the device name for 3-Axis Sensor"
                default "i2c4"
        endif

endmenu

menu "Board extended module Drivers"

endmenu

endmenu