/* * The Clear BSD License * Copyright (c) 2015, Freescale Semiconductor, Inc. * Copyright 2016-2017 NXP * All rights reserved. * * Redistribution and use in source and binary forms, with or without modification, * are permitted (subject to the limitations in the disclaimer below) provided * that the following conditions are met: * * o Redistributions of source code must retain the above copyright notice, this list * of conditions and the following disclaimer. * * o Redistributions in binary form must reproduce the above copyright notice, this * list of conditions and the following disclaimer in the documentation and/or * other materials provided with the distribution. * * o Neither the name of the copyright holder nor the names of its * contributors may be used to endorse or promote products derived from this * software without specific prior written permission. * * NO EXPRESS OR IMPLIED LICENSES TO ANY PARTY'S PATENT RIGHTS ARE GRANTED BY THIS LICENSE. * THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND * ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED * WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE * DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE LIABLE FOR * ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES * (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; * LOSS OF USE, DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON * ANY THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT * (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS * SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE. */ #ifndef _FSL_PWM_H_ #define _FSL_PWM_H_ #include "fsl_common.h" /*! * @addtogroup pwm_driver * @{ */ /******************************************************************************* * Definitions ******************************************************************************/ /*! @name Driver version */ /*@{*/ #define FSL_PWM_DRIVER_VERSION (MAKE_VERSION(2, 0, 0)) /*!< Version 2.0.0 */ /*@}*/ /*! Number of bits per submodule for software output control */ #define PWM_SUBMODULE_SWCONTROL_WIDTH 2 /*! @brief List of PWM submodules */ typedef enum _pwm_submodule { kPWM_Module_0 = 0U, /*!< Submodule 0 */ kPWM_Module_1, /*!< Submodule 1 */ kPWM_Module_2, /*!< Submodule 2 */ kPWM_Module_3 /*!< Submodule 3 */ } pwm_submodule_t; /*! @brief List of PWM channels in each module */ typedef enum _pwm_channels { kPWM_PwmB = 0U, kPWM_PwmA, kPWM_PwmX } pwm_channels_t; /*! @brief List of PWM value registers */ typedef enum _pwm_value_register { kPWM_ValueRegister_0 = 0U, /*!< PWM Value0 register */ kPWM_ValueRegister_1, /*!< PWM Value1 register */ kPWM_ValueRegister_2, /*!< PWM Value2 register */ kPWM_ValueRegister_3, /*!< PWM Value3 register */ kPWM_ValueRegister_4, /*!< PWM Value4 register */ kPWM_ValueRegister_5 /*!< PWM Value5 register */ } pwm_value_register_t; /*! @brief PWM clock source selection.*/ typedef enum _pwm_clock_source { kPWM_BusClock = 0U, /*!< The IPBus clock is used as the clock */ kPWM_ExternalClock, /*!< EXT_CLK is used as the clock */ kPWM_Submodule0Clock /*!< Clock of the submodule 0 (AUX_CLK) is used as the source clock */ } pwm_clock_source_t; /*! @brief PWM prescaler factor selection for clock source*/ typedef enum _pwm_clock_prescale { kPWM_Prescale_Divide_1 = 0U, /*!< PWM clock frequency = fclk/1 */ kPWM_Prescale_Divide_2, /*!< PWM clock frequency = fclk/2 */ kPWM_Prescale_Divide_4, /*!< PWM clock frequency = fclk/4 */ kPWM_Prescale_Divide_8, /*!< PWM clock frequency = fclk/8 */ kPWM_Prescale_Divide_16, /*!< PWM clock frequency = fclk/16 */ kPWM_Prescale_Divide_32, /*!< PWM clock frequency = fclk/32 */ kPWM_Prescale_Divide_64, /*!< PWM clock frequency = fclk/64 */ kPWM_Prescale_Divide_128 /*!< PWM clock frequency = fclk/128 */ } pwm_clock_prescale_t; /*! @brief Options that can trigger a PWM FORCE_OUT */ typedef enum _pwm_force_output_trigger { kPWM_Force_Local = 0U, /*!< The local force signal, CTRL2[FORCE], from the submodule is used to force updates */ kPWM_Force_Master, /*!< The master force signal from submodule 0 is used to force updates */ kPWM_Force_LocalReload, /*!< The local reload signal from this submodule is used to force updates without regard to the state of LDOK */ kPWM_Force_MasterReload, /*!< The master reload signal from submodule 0 is used to force updates if LDOK is set */ kPWM_Force_LocalSync, /*!< The local sync signal from this submodule is used to force updates */ kPWM_Force_MasterSync, /*!< The master sync signal from submodule0 is used to force updates */ kPWM_Force_External, /*!< The external force signal, EXT_FORCE, from outside the PWM module causes updates */ kPWM_Force_ExternalSync /*!< The external sync signal, EXT_SYNC, from outside the PWM module causes updates */ } pwm_force_output_trigger_t; /*! @brief PWM counter initialization options */ typedef enum _pwm_init_source { kPWM_Initialize_LocalSync = 0U, /*!< Local sync causes initialization */ kPWM_Initialize_MasterReload, /*!< Master reload from submodule 0 causes initialization */ kPWM_Initialize_MasterSync, /*!< Master sync from submodule 0 causes initialization */ kPWM_Initialize_ExtSync /*!< EXT_SYNC causes initialization */ } pwm_init_source_t; /*! @brief PWM load frequency selection */ typedef enum _pwm_load_frequency { kPWM_LoadEveryOportunity = 0U, /*!< Every PWM opportunity */ kPWM_LoadEvery2Oportunity, /*!< Every 2 PWM opportunities */ kPWM_LoadEvery3Oportunity, /*!< Every 3 PWM opportunities */ kPWM_LoadEvery4Oportunity, /*!< Every 4 PWM opportunities */ kPWM_LoadEvery5Oportunity, /*!< Every 5 PWM opportunities */ kPWM_LoadEvery6Oportunity, /*!< Every 6 PWM opportunities */ kPWM_LoadEvery7Oportunity, /*!< Every 7 PWM opportunities */ kPWM_LoadEvery8Oportunity, /*!< Every 8 PWM opportunities */ kPWM_LoadEvery9Oportunity, /*!< Every 9 PWM opportunities */ kPWM_LoadEvery10Oportunity, /*!< Every 10 PWM opportunities */ kPWM_LoadEvery11Oportunity, /*!< Every 11 PWM opportunities */ kPWM_LoadEvery12Oportunity, /*!< Every 12 PWM opportunities */ kPWM_LoadEvery13Oportunity, /*!< Every 13 PWM opportunities */ kPWM_LoadEvery14Oportunity, /*!< Every 14 PWM opportunities */ kPWM_LoadEvery15Oportunity, /*!< Every 15 PWM opportunities */ kPWM_LoadEvery16Oportunity /*!< Every 16 PWM opportunities */ } pwm_load_frequency_t; /*! @brief List of PWM fault selections */ typedef enum _pwm_fault_input { kPWM_Fault_0 = 0U, /*!< Fault 0 input pin */ kPWM_Fault_1, /*!< Fault 1 input pin */ kPWM_Fault_2, /*!< Fault 2 input pin */ kPWM_Fault_3 /*!< Fault 3 input pin */ } pwm_fault_input_t; /*! @brief PWM capture edge select */ typedef enum _pwm_input_capture_edge { kPWM_Disable = 0U, /*!< Disabled */ kPWM_FallingEdge, /*!< Capture on falling edge only */ kPWM_RisingEdge, /*!< Capture on rising edge only */ kPWM_RiseAndFallEdge /*!< Capture on rising or falling edge */ } pwm_input_capture_edge_t; /*! @brief PWM output options when a FORCE_OUT signal is asserted */ typedef enum _pwm_force_signal { kPWM_UsePwm = 0U, /*!< Generated PWM signal is used by the deadtime logic.*/ kPWM_InvertedPwm, /*!< Inverted PWM signal is used by the deadtime logic.*/ kPWM_SoftwareControl, /*!< Software controlled value is used by the deadtime logic. */ kPWM_UseExternal /*!< PWM_EXTA signal is used by the deadtime logic. */ } pwm_force_signal_t; /*! @brief Options available for the PWM A & B pair operation */ typedef enum _pwm_chnl_pair_operation { kPWM_Independent = 0U, /*!< PWM A & PWM B operate as 2 independent channels */ kPWM_ComplementaryPwmA, /*!< PWM A & PWM B are complementary channels, PWM A generates the signal */ kPWM_ComplementaryPwmB /*!< PWM A & PWM B are complementary channels, PWM B generates the signal */ } pwm_chnl_pair_operation_t; /*! @brief Options available on how to load the buffered-registers with new values */ typedef enum _pwm_register_reload { kPWM_ReloadImmediate = 0U, /*!< Buffered-registers get loaded with new values as soon as LDOK bit is set */ kPWM_ReloadPwmHalfCycle, /*!< Registers loaded on a PWM half cycle */ kPWM_ReloadPwmFullCycle, /*!< Registers loaded on a PWM full cycle */ kPWM_ReloadPwmHalfAndFullCycle /*!< Registers loaded on a PWM half & full cycle */ } pwm_register_reload_t; /*! @brief Options available on how to re-enable the PWM output when recovering from a fault */ typedef enum _pwm_fault_recovery_mode { kPWM_NoRecovery = 0U, /*!< PWM output will stay inactive */ kPWM_RecoverHalfCycle, /*!< PWM output re-enabled at the first half cycle */ kPWM_RecoverFullCycle, /*!< PWM output re-enabled at the first full cycle */ kPWM_RecoverHalfAndFullCycle /*!< PWM output re-enabled at the first half or full cycle */ } pwm_fault_recovery_mode_t; /*! @brief List of PWM interrupt options */ typedef enum _pwm_interrupt_enable { kPWM_CompareVal0InterruptEnable = (1U << 0), /*!< PWM VAL0 compare interrupt */ kPWM_CompareVal1InterruptEnable = (1U << 1), /*!< PWM VAL1 compare interrupt */ kPWM_CompareVal2InterruptEnable = (1U << 2), /*!< PWM VAL2 compare interrupt */ kPWM_CompareVal3InterruptEnable = (1U << 3), /*!< PWM VAL3 compare interrupt */ kPWM_CompareVal4InterruptEnable = (1U << 4), /*!< PWM VAL4 compare interrupt */ kPWM_CompareVal5InterruptEnable = (1U << 5), /*!< PWM VAL5 compare interrupt */ kPWM_CaptureX0InterruptEnable = (1U << 6), /*!< PWM capture X0 interrupt */ kPWM_CaptureX1InterruptEnable = (1U << 7), /*!< PWM capture X1 interrupt */ kPWM_CaptureB0InterruptEnable = (1U << 8), /*!< PWM capture B0 interrupt */ kPWM_CaptureB1InterruptEnable = (1U << 9), /*!< PWM capture B1 interrupt */ kPWM_CaptureA0InterruptEnable = (1U << 10), /*!< PWM capture A0 interrupt */ kPWM_CaptureA1InterruptEnable = (1U << 11), /*!< PWM capture A1 interrupt */ kPWM_ReloadInterruptEnable = (1U << 12), /*!< PWM reload interrupt */ kPWM_ReloadErrorInterruptEnable = (1U << 13), /*!< PWM reload error interrupt */ kPWM_Fault0InterruptEnable = (1U << 16), /*!< PWM fault 0 interrupt */ kPWM_Fault1InterruptEnable = (1U << 17), /*!< PWM fault 1 interrupt */ kPWM_Fault2InterruptEnable = (1U << 18), /*!< PWM fault 2 interrupt */ kPWM_Fault3InterruptEnable = (1U << 19) /*!< PWM fault 3 interrupt */ } pwm_interrupt_enable_t; /*! @brief List of PWM status flags */ typedef enum _pwm_status_flags { kPWM_CompareVal0Flag = (1U << 0), /*!< PWM VAL0 compare flag */ kPWM_CompareVal1Flag = (1U << 1), /*!< PWM VAL1 compare flag */ kPWM_CompareVal2Flag = (1U << 2), /*!< PWM VAL2 compare flag */ kPWM_CompareVal3Flag = (1U << 3), /*!< PWM VAL3 compare flag */ kPWM_CompareVal4Flag = (1U << 4), /*!< PWM VAL4 compare flag */ kPWM_CompareVal5Flag = (1U << 5), /*!< PWM VAL5 compare flag */ kPWM_CaptureX0Flag = (1U << 6), /*!< PWM capture X0 flag */ kPWM_CaptureX1Flag = (1U << 7), /*!< PWM capture X1 flag */ kPWM_CaptureB0Flag = (1U << 8), /*!< PWM capture B0 flag */ kPWM_CaptureB1Flag = (1U << 9), /*!< PWM capture B1 flag */ kPWM_CaptureA0Flag = (1U << 10), /*!< PWM capture A0 flag */ kPWM_CaptureA1Flag = (1U << 11), /*!< PWM capture A1 flag */ kPWM_ReloadFlag = (1U << 12), /*!< PWM reload flag */ kPWM_ReloadErrorFlag = (1U << 13), /*!< PWM reload error flag */ kPWM_RegUpdatedFlag = (1U << 14), /*!< PWM registers updated flag */ kPWM_Fault0Flag = (1U << 16), /*!< PWM fault 0 flag */ kPWM_Fault1Flag = (1U << 17), /*!< PWM fault 1 flag */ kPWM_Fault2Flag = (1U << 18), /*!< PWM fault 2 flag */ kPWM_Fault3Flag = (1U << 19) /*!< PWM fault 3 flag */ } pwm_status_flags_t; /*! @brief PWM operation mode */ typedef enum _pwm_mode { kPWM_SignedCenterAligned = 0U, /*!< Signed center-aligned */ kPWM_CenterAligned, /*!< Unsigned cente-aligned */ kPWM_SignedEdgeAligned, /*!< Signed edge-aligned */ kPWM_EdgeAligned /*!< Unsigned edge-aligned */ } pwm_mode_t; /*! @brief PWM output pulse mode, high-true or low-true */ typedef enum _pwm_level_select { kPWM_HighTrue = 0U, /*!< High level represents "on" or "active" state */ kPWM_LowTrue /*!< Low level represents "on" or "active" state */ } pwm_level_select_t; /*! @brief PWM reload source select */ typedef enum _pwm_reload_source_select { kPWM_LocalReload = 0U, /*!< The local reload signal is used to reload registers */ kPWM_MasterReload /*!< The master reload signal (from submodule 0) is used to reload */ } pwm_reload_source_select_t; /*! @brief PWM fault clearing options */ typedef enum _pwm_fault_clear { kPWM_Automatic = 0U, /*!< Automatic fault clearing */ kPWM_ManualNormal, /*!< Manual fault clearing with no fault safety mode */ kPWM_ManualSafety /*!< Manual fault clearing with fault safety mode */ } pwm_fault_clear_t; /*! @brief Options for submodule master control operation */ typedef enum _pwm_module_control { kPWM_Control_Module_0 = (1U << 0), /*!< Control submodule 0's start/stop,buffer reload operation */ kPWM_Control_Module_1 = (1U << 1), /*!< Control submodule 1's start/stop,buffer reload operation */ kPWM_Control_Module_2 = (1U << 2), /*!< Control submodule 2's start/stop,buffer reload operation */ kPWM_Control_Module_3 = (1U << 3) /*!< Control submodule 3's start/stop,buffer reload operation */ } pwm_module_control_t; /*! @brief Structure for the user to define the PWM signal characteristics */ typedef struct _pwm_signal_param { pwm_channels_t pwmChannel; /*!< PWM channel being configured; PWM A or PWM B */ uint8_t dutyCyclePercent; /*!< PWM pulse width, value should be between 0 to 100 0=inactive signal(0% duty cycle)... 100=always active signal (100% duty cycle)*/ pwm_level_select_t level; /*!< PWM output active level select */ uint16_t deadtimeValue; /*!< The deadtime value; only used if channel pair is operating in complementary mode */ } pwm_signal_param_t; /*! * @brief PWM config structure * * This structure holds the configuration settings for the PWM peripheral. To initialize this * structure to reasonable defaults, call the PWM_GetDefaultConfig() function and pass a * pointer to your config structure instance. * * The config struct can be made const so it resides in flash */ typedef struct _pwm_config { bool enableDebugMode; /*!< true: PWM continues to run in debug mode; false: PWM is paused in debug mode */ bool enableWait; /*!< true: PWM continues to run in WAIT mode; false: PWM is paused in WAIT mode */ uint8_t faultFilterCount; /*!< Fault filter count */ uint8_t faultFilterPeriod; /*!< Fault filter period;value of 0 will bypass the filter */ pwm_init_source_t initializationControl; /*!< Option to initialize the counter */ pwm_clock_source_t clockSource; /*!< Clock source for the counter */ pwm_clock_prescale_t prescale; /*!< Pre-scaler to divide down the clock */ pwm_chnl_pair_operation_t pairOperation; /*!< Channel pair in indepedent or complementary mode */ pwm_register_reload_t reloadLogic; /*!< PWM Reload logic setup */ pwm_reload_source_select_t reloadSelect; /*!< Reload source select */ pwm_load_frequency_t reloadFrequency; /*!< Specifies when to reload, used when user's choice is not immediate reload */ pwm_force_output_trigger_t forceTrigger; /*!< Specify which signal will trigger a FORCE_OUT */ } pwm_config_t; /*! @brief Structure is used to hold the parameters to configure a PWM fault */ typedef struct _pwm_fault_param { pwm_fault_clear_t faultClearingMode; /*!< Fault clearing mode to use */ bool faultLevel; /*!< true: Logic 1 indicates fault; false: Logic 0 indicates fault */ bool enableCombinationalPath; /*!< true: Combinational Path from fault input is enabled; false: No combination path is available */ pwm_fault_recovery_mode_t recoverMode; /*!< Specify when to re-enable the PWM output */ } pwm_fault_param_t; /*! * @brief Structure is used to hold parameters to configure the capture capability of a signal pin */ typedef struct _pwm_input_capture_param { bool captureInputSel; /*!< true: Use the edge counter signal as source false: Use the raw input signal from the pin as source */ uint8_t edgeCompareValue; /*!< Compare value, used only if edge counter is used as source */ pwm_input_capture_edge_t edge0; /*!< Specify which edge causes a capture for input circuitry 0 */ pwm_input_capture_edge_t edge1; /*!< Specify which edge causes a capture for input circuitry 1 */ bool enableOneShotCapture; /*!< true: Use one-shot capture mode; false: Use free-running capture mode */ uint8_t fifoWatermark; /*!< Watermark level for capture FIFO. The capture flags in the status register will set if the word count in the FIFO is greater than this watermark level */ } pwm_input_capture_param_t; /******************************************************************************* * API ******************************************************************************/ #if defined(__cplusplus) extern "C" { #endif /*! * @name Initialization and deinitialization * @{ */ /*! * @brief Ungates the PWM submodule clock and configures the peripheral for basic operation. * * @note This API should be called at the beginning of the application using the PWM driver. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param config Pointer to user's PWM config structure. * * @return kStatus_Success means success; else failed. */ status_t PWM_Init(PWM_Type *base, pwm_submodule_t subModule, const pwm_config_t *config); /*! * @brief Gate the PWM submodule clock * * @param base PWM peripheral base address * @param subModule PWM submodule to deinitialize */ void PWM_Deinit(PWM_Type *base, pwm_submodule_t subModule); /*! * @brief Fill in the PWM config struct with the default settings * * The default values are: * @code * config->enableDebugMode = false; * config->enableWait = false; * config->reloadSelect = kPWM_LocalReload; * config->faultFilterCount = 0; * config->faultFilterPeriod = 0; * config->clockSource = kPWM_BusClock; * config->prescale = kPWM_Prescale_Divide_1; * config->initializationControl = kPWM_Initialize_LocalSync; * config->forceTrigger = kPWM_Force_Local; * config->reloadFrequency = kPWM_LoadEveryOportunity; * config->reloadLogic = kPWM_ReloadImmediate; * config->pairOperation = kPWM_Independent; * @endcode * @param config Pointer to user's PWM config structure. */ void PWM_GetDefaultConfig(pwm_config_t *config); /*! @}*/ /*! * @name Module PWM output * @{ */ /*! * @brief Sets up the PWM signals for a PWM submodule. * * The function initializes the submodule according to the parameters passed in by the user. The function * also sets up the value compare registers to match the PWM signal requirements. * If the dead time insertion logic is enabled, the pulse period is reduced by the * dead time period specified by the user. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param chnlParams Array of PWM channel parameters to configure the channel(s) * @param numOfChnls Number of channels to configure, this should be the size of the array passed in. * Array size should not be more than 2 as each submodule has 2 pins to output PWM * @param mode PWM operation mode, options available in enumeration ::pwm_mode_t * @param pwmFreq_Hz PWM signal frequency in Hz * @param srcClock_Hz PWM main counter clock in Hz. * * @return Returns kStatusFail if there was error setting up the signal; kStatusSuccess otherwise */ status_t PWM_SetupPwm(PWM_Type *base, pwm_submodule_t subModule, const pwm_signal_param_t *chnlParams, uint8_t numOfChnls, pwm_mode_t mode, uint32_t pwmFreq_Hz, uint32_t srcClock_Hz); /*! * @brief Updates the PWM signal's dutycycle. * * The function updates the PWM dutycyle to the new value that is passed in. * If the dead time insertion logic is enabled then the pulse period is reduced by the * dead time period specified by the user. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param pwmSignal Signal (PWM A or PWM B) to update * @param currPwmMode The current PWM mode set during PWM setup * @param dutyCyclePercent New PWM pulse width, value should be between 0 to 100 * 0=inactive signal(0% duty cycle)... * 100=active signal (100% duty cycle) */ void PWM_UpdatePwmDutycycle(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmSignal, pwm_mode_t currPwmMode, uint8_t dutyCyclePercent); /*! @}*/ /*! * @brief Sets up the PWM input capture * * Each PWM submodule has 3 pins that can be configured for use as input capture pins. This function * sets up the capture parameters for each pin and enables the pin for input capture operation. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param pwmChannel Channel in the submodule to setup * @param inputCaptureParams Parameters passed in to set up the input pin */ void PWM_SetupInputCapture(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, const pwm_input_capture_param_t *inputCaptureParams); /*! * @brief Sets up the PWM fault protection. * * PWM has 4 fault inputs. * * @param base PWM peripheral base address * @param faultNum PWM fault to configure. * @param faultParams Pointer to the PWM fault config structure */ void PWM_SetupFaults(PWM_Type *base, pwm_fault_input_t faultNum, const pwm_fault_param_t *faultParams); /*! * @brief Selects the signal to output on a PWM pin when a FORCE_OUT signal is asserted. * * The user specifies which channel to configure by supplying the submodule number and whether * to modify PWM A or PWM B within that submodule. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param pwmChannel Channel to configure * @param mode Signal to output when a FORCE_OUT is triggered */ void PWM_SetupForceSignal(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, pwm_force_signal_t mode); /*! * @name Interrupts Interface * @{ */ /*! * @brief Enables the selected PWM interrupts * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param mask The interrupts to enable. This is a logical OR of members of the * enumeration ::pwm_interrupt_enable_t */ void PWM_EnableInterrupts(PWM_Type *base, pwm_submodule_t subModule, uint32_t mask); /*! * @brief Disables the selected PWM interrupts * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param mask The interrupts to enable. This is a logical OR of members of the * enumeration ::pwm_interrupt_enable_t */ void PWM_DisableInterrupts(PWM_Type *base, pwm_submodule_t subModule, uint32_t mask); /*! * @brief Gets the enabled PWM interrupts * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * * @return The enabled interrupts. This is the logical OR of members of the * enumeration ::pwm_interrupt_enable_t */ uint32_t PWM_GetEnabledInterrupts(PWM_Type *base, pwm_submodule_t subModule); /*! @}*/ /*! * @name Status Interface * @{ */ /*! * @brief Gets the PWM status flags * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * * @return The status flags. This is the logical OR of members of the * enumeration ::pwm_status_flags_t */ uint32_t PWM_GetStatusFlags(PWM_Type *base, pwm_submodule_t subModule); /*! * @brief Clears the PWM status flags * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param mask The status flags to clear. This is a logical OR of members of the * enumeration ::pwm_status_flags_t */ void PWM_ClearStatusFlags(PWM_Type *base, pwm_submodule_t subModule, uint32_t mask); /*! @}*/ /*! * @name Timer Start and Stop * @{ */ /*! * @brief Starts the PWM counter for a single or multiple submodules. * * Sets the Run bit which enables the clocks to the PWM submodule. This function can start multiple * submodules at the same time. * * @param base PWM peripheral base address * @param subModulesToStart PWM submodules to start. This is a logical OR of members of the * enumeration ::pwm_module_control_t */ static inline void PWM_StartTimer(PWM_Type *base, uint8_t subModulesToStart) { base->MCTRL |= PWM_MCTRL_RUN(subModulesToStart); } /*! * @brief Stops the PWM counter for a single or multiple submodules. * * Clears the Run bit which resets the submodule's counter. This function can stop multiple * submodules at the same time. * * @param base PWM peripheral base address * @param subModulesToStop PWM submodules to stop. This is a logical OR of members of the * enumeration ::pwm_module_control_t */ static inline void PWM_StopTimer(PWM_Type *base, uint8_t subModulesToStop) { base->MCTRL &= ~(PWM_MCTRL_RUN(subModulesToStop)); } /*! @}*/ /*! * @brief Enables or disables the PWM output trigger. * * This function allows the user to enable or disable the PWM trigger. The PWM has 2 triggers. Trigger 0 * is activated when the counter matches VAL 0, VAL 2, or VAL 4 register. Trigger 1 is activated * when the counter matches VAL 1, VAL 3, or VAL 5 register. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param valueRegister Value register that will activate the trigger * @param activate true: Enable the trigger; false: Disable the trigger */ static inline void PWM_OutputTriggerEnable(PWM_Type *base, pwm_submodule_t subModule, pwm_value_register_t valueRegister, bool activate) { if (activate) { base->SM[subModule].TCTRL |= (1U << valueRegister); } else { base->SM[subModule].TCTRL &= ~(1U << valueRegister); } } /*! * @brief Sets the software control output for a pin to high or low. * * The user specifies which channel to modify by supplying the submodule number and whether * to modify PWM A or PWM B within that submodule. * * @param base PWM peripheral base address * @param subModule PWM submodule to configure * @param pwmChannel Channel to configure * @param value true: Supply a logic 1, false: Supply a logic 0. */ static inline void PWM_SetupSwCtrlOut(PWM_Type *base, pwm_submodule_t subModule, pwm_channels_t pwmChannel, bool value) { if (value) { base->SWCOUT |= (1U << ((subModule * PWM_SUBMODULE_SWCONTROL_WIDTH) + pwmChannel)); } else { base->SWCOUT &= ~(1U << ((subModule * PWM_SUBMODULE_SWCONTROL_WIDTH) + pwmChannel)); } } /*! * @brief Sets or clears the PWM LDOK bit on a single or multiple submodules * * Set LDOK bit to load buffered values into CTRL[PRSC] and the INIT, FRACVAL and VAL registers. The * values are loaded immediately if kPWM_ReloadImmediate option was choosen during config. Else the * values are loaded at the next PWM reload point. * This function can issue the load command to multiple submodules at the same time. * * @param base PWM peripheral base address * @param subModulesToUpdate PWM submodules to update with buffered values. This is a logical OR of * members of the enumeration ::pwm_module_control_t * @param value true: Set LDOK bit for the submodule list; false: Clear LDOK bit */ static inline void PWM_SetPwmLdok(PWM_Type *base, uint8_t subModulesToUpdate, bool value) { if (value) { base->MCTRL |= PWM_MCTRL_LDOK(subModulesToUpdate); } else { base->MCTRL |= PWM_MCTRL_CLDOK(subModulesToUpdate); } } #if defined(__cplusplus) } #endif /*! @}*/ #endif /* _FSL_PWM_H_ */