//***************************************************************************** // // usb.c - Driver for the USB Interface. // // Copyright (c) 2007-2010 Texas Instruments Incorporated. All rights reserved. // Software License Agreement // // Texas Instruments (TI) is supplying this software for use solely and // exclusively on TI's microcontroller products. The software is owned by // TI and/or its suppliers, and is protected under applicable copyright // laws. You may not combine this software with "viral" open-source // software in order to form a larger program. // // THIS SOFTWARE IS PROVIDED "AS IS" AND WITH ALL FAULTS. // NO WARRANTIES, WHETHER EXPRESS, IMPLIED OR STATUTORY, INCLUDING, BUT // NOT LIMITED TO, IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR // A PARTICULAR PURPOSE APPLY TO THIS SOFTWARE. TI SHALL NOT, UNDER ANY // CIRCUMSTANCES, BE LIABLE FOR SPECIAL, INCIDENTAL, OR CONSEQUENTIAL // DAMAGES, FOR ANY REASON WHATSOEVER. // // This is part of revision 6459 of the Stellaris Peripheral Driver Library. // //***************************************************************************** //***************************************************************************** // //! \addtogroup usb_api //! @{ // //***************************************************************************** #include "inc/hw_ints.h" #include "inc/hw_memmap.h" #include "inc/hw_types.h" #include "inc/hw_usb.h" #include "driverlib/debug.h" #include "driverlib/interrupt.h" #include "driverlib/udma.h" #include "driverlib/usb.h" //***************************************************************************** // // Amount to shift the RX interrupt sources by in the flags used in the // interrupt calls. // //***************************************************************************** #ifndef DEPRECATED #define USB_INT_RX_SHIFT 8 #endif #define USB_INTEP_RX_SHIFT 16 //***************************************************************************** // // Amount to shift the status interrupt sources by in the flags used in the // interrupt calls. // //***************************************************************************** #ifndef DEPRECATED #define USB_INT_STATUS_SHIFT 24 #endif //***************************************************************************** // // Amount to shift the RX endpoint status sources by in the flags used in the // calls. // //***************************************************************************** #define USB_RX_EPSTATUS_SHIFT 16 //***************************************************************************** // // Converts from an endpoint specifier to the offset of the endpoint's // control/status registers. // //***************************************************************************** #define EP_OFFSET(Endpoint) (Endpoint - 0x10) //***************************************************************************** // // Sets one of the indexed registers. // // \param ulBase specifies the USB module base address. // \param ulEndpoint is the endpoint index to target for this write. // \param ulIndexedReg is the indexed register to write to. // \param ucValue is the value to write to the register. // // This function is used to access the indexed registers for each endpoint. // The only registers that are indexed are the FIFO configuration registers // which are not used after configuration. // // \return None. // //***************************************************************************** static void USBIndexWrite(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulIndexedReg, unsigned long ulValue, unsigned long ulSize) { unsigned long ulIndex; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == 0) || (ulEndpoint == 1) || (ulEndpoint == 2) || (ulEndpoint == 3)); ASSERT((ulSize == 1) || (ulSize == 2)); // // Save the old index in case it was in use. // ulIndex = HWREGB(ulBase + USB_O_EPIDX); // // Set the index. // HWREGB(ulBase + USB_O_EPIDX) = ulEndpoint; // // Determine the size of the register value. // if(ulSize == 1) { // // Set the value. // HWREGB(ulBase + ulIndexedReg) = ulValue; } else { // // Set the value. // HWREGH(ulBase + ulIndexedReg) = ulValue; } // // Restore the old index in case it was in use. // HWREGB(ulBase + USB_O_EPIDX) = ulIndex; } //***************************************************************************** // // Reads one of the indexed registers. // // \param ulBase specifies the USB module base address. // \param ulEndpoint is the endpoint index to target for this write. // \param ulIndexedReg is the indexed register to write to. // // This function is used internally to access the indexed registers for each // endpoint. The only registers that are indexed are the FIFO configuration // registers which are not used after configuration. // // \return The value in the register requested. // //***************************************************************************** static unsigned long USBIndexRead(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulIndexedReg, unsigned long ulSize) { unsigned char ulIndex; unsigned char ulValue; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == 0) || (ulEndpoint == 1) || (ulEndpoint == 2) || (ulEndpoint == 3)); ASSERT((ulSize == 1) || (ulSize == 2)); // // Save the old index in case it was in use. // ulIndex = HWREGB(ulBase + USB_O_EPIDX); // // Set the index. // HWREGB(ulBase + USB_O_EPIDX) = ulEndpoint; // // Determine the size of the register value. // if(ulSize == 1) { // // Get the value. // ulValue = HWREGB(ulBase + ulIndexedReg); } else { // // Get the value. // ulValue = HWREGH(ulBase + ulIndexedReg); } // // Restore the old index in case it was in use. // HWREGB(ulBase + USB_O_EPIDX) = ulIndex; // // Return the register's value. // return(ulValue); } //***************************************************************************** // //! Puts the USB bus in a suspended state. //! //! \param ulBase specifies the USB module base address. //! //! When used in host mode, this function will put the USB bus in the suspended //! state. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostSuspend(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Send the suspend signaling to the USB bus. // HWREGB(ulBase + USB_O_POWER) |= USB_POWER_SUSPEND; } //***************************************************************************** // //! Handles the USB bus reset condition. //! //! \param ulBase specifies the USB module base address. //! \param bStart specifies whether to start or stop signaling reset on the USB //! bus. //! //! When this function is called with the \e bStart parameter set to \b true, //! this function will cause the start of a reset condition on the USB bus. //! The caller should then delay at least 20ms before calling this function //! again with the \e bStart parameter set to \b false. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostReset(unsigned long ulBase, tBoolean bStart) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Send a reset signal to the bus. // if(bStart) { HWREGB(ulBase + USB_O_POWER) |= USB_POWER_RESET; } else { HWREGB(ulBase + USB_O_POWER) &= ~USB_POWER_RESET; } } //***************************************************************************** // //! Handles the USB bus resume condition. //! //! \param ulBase specifies the USB module base address. //! \param bStart specifies if the USB controller is entering or leaving the //! resume signaling state. //! //! When in device mode this function will bring the USB controller out of the //! suspend state. This call should first be made with the \e bStart parameter //! set to \b true to start resume signaling. The device application should //! then delay at least 10ms but not more than 15ms before calling this //! function with the \e bStart parameter set to \b false. //! //! When in host mode this function will signal devices to leave the suspend //! state. This call should first be made with the \e bStart parameter set to //! \b true to start resume signaling. The host application should then delay //! at least 20ms before calling this function with the \e bStart parameter set //! to \b false. This will cause the controller to complete the resume //! signaling on the USB bus. //! //! \return None. // //***************************************************************************** void USBHostResume(unsigned long ulBase, tBoolean bStart) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Send a resume signal to the bus. // if(bStart) { HWREGB(ulBase + USB_O_POWER) |= USB_POWER_RESUME; } else { HWREGB(ulBase + USB_O_POWER) &= ~USB_POWER_RESUME; } } //***************************************************************************** // //! Returns the current speed of the USB device connected. //! //! \param ulBase specifies the USB module base address. //! //! This function will return the current speed of the USB bus. //! //! \note This function should only be called in host mode. //! //! \return Returns either \b USB_LOW_SPEED, \b USB_FULL_SPEED, or //! \b USB_UNDEF_SPEED. // //***************************************************************************** unsigned long USBHostSpeedGet(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // If the Full Speed device bit is set, then this is a full speed device. // if(HWREGB(ulBase + USB_O_DEVCTL) & USB_DEVCTL_FSDEV) { return(USB_FULL_SPEED); } // // If the Low Speed device bit is set, then this is a low speed device. // if(HWREGB(ulBase + USB_O_DEVCTL) & USB_DEVCTL_LSDEV) { return(USB_LOW_SPEED); } // // The device speed is not known. // return(USB_UNDEF_SPEED); } //***************************************************************************** // //! Returns the status of the USB interrupts. //! //! \param ulBase specifies the USB module base address. //! //! This function will read the source of the interrupt for the USB controller. //! There are three groups of interrupt sources, IN Endpoints, OUT Endpoints, //! and general status changes. This call will return the current status for //! all of these interrupts. The bit values returned should be compared //! against the \b USB_HOST_IN, \b USB_HOST_OUT, \b USB_HOST_EP0, //! \b USB_DEV_IN, \b USB_DEV_OUT, and \b USB_DEV_EP0 values. //! //! \note This call will clear the source of all of the general status //! interrupts. //! //! \note WARNING: This API cannot be used on endpoint numbers greater than //! endpoint 3 so USBIntStatusControl() or USBIntStatusEndpoint() should be //! used instead. //! //! \return Returns the status of the sources for the USB controller's //! interrupt. // //***************************************************************************** #ifndef DEPRECATED unsigned long USBIntStatus(unsigned long ulBase) { unsigned long ulStatus; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Get the transmit interrupt status. // ulStatus = (HWREGB(ulBase + USB_O_TXIS)); // // Get the receive interrupt status, these bits go into the second byte of // the returned value. // ulStatus |= (HWREGB(ulBase + USB_O_RXIS) << USB_INT_RX_SHIFT); // // Get the general interrupt status, these bits go into the upper 8 bits // of the returned value. // ulStatus |= (HWREGB(ulBase + USB_O_IS) << USB_INT_STATUS_SHIFT); // // Add the power fault status. // if(HWREG(ulBase + USB_O_EPCISC) & USB_EPCISC_PF) { // // Indicate a power fault was detected. // ulStatus |= USB_INT_POWER_FAULT; // // Clear the power fault interrupt. // HWREGB(ulBase + USB_O_EPCISC) |= USB_EPCISC_PF; } if(HWREG(USB0_BASE + USB_O_IDVISC) & USB_IDVRIS_ID) { // // Indicate a id detection was detected. // ulStatus |= USB_INT_MODE_DETECT; // // Clear the id detection interrupt. // HWREG(USB0_BASE + USB_O_IDVISC) |= USB_IDVRIS_ID; } // // Return the combined interrupt status. // return(ulStatus); } #endif //***************************************************************************** // //! Disables the sources for USB interrupts. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies which interrupts to disable. //! //! This function will disable the USB controller from generating the //! interrupts indicated by the \e ulFlags parameter. There are three groups //! of interrupt sources, IN Endpoints, OUT Endpoints, and general status //! changes, specified by \b USB_INT_HOST_IN, \b USB_INT_HOST_OUT, //! \b USB_INT_DEV_IN, \b USB_INT_DEV_OUT, and \b USB_INT_STATUS. If //! \b USB_INT_ALL is specified then all interrupts will be disabled. //! //! \note WARNING: This API cannot be used on endpoint numbers greater than //! endpoint 3 so USBIntDisableControl() or USBIntDisableEndpoint() should be //! used instead. //! //! \return None. // //***************************************************************************** #ifndef DEPRECATED void USBIntDisable(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulFlags & ~(USB_INT_ALL)) == 0); // // If any transmit interrupts were disabled then write the transmit // interrupt settings out to the hardware. // if(ulFlags & (USB_INT_HOST_OUT | USB_INT_DEV_IN | USB_INT_EP0)) { HWREGH(ulBase + USB_O_TXIE) &= ~(ulFlags & (USB_INT_HOST_OUT | USB_INT_DEV_IN | USB_INT_EP0)); } // // If any receive interrupts were disabled then write the receive interrupt // settings out to the hardware. // if(ulFlags & (USB_INT_HOST_IN | USB_INT_DEV_OUT)) { HWREGH(ulBase + USB_O_RXIE) &= ~((ulFlags & (USB_INT_HOST_IN | USB_INT_DEV_OUT)) >> USB_INT_RX_SHIFT); } // // If any general interrupts were disabled then write the general interrupt // settings out to the hardware. // if(ulFlags & USB_INT_STATUS) { HWREGB(ulBase + USB_O_IE) &= ~((ulFlags & USB_INT_STATUS) >> USB_INT_STATUS_SHIFT); } // // Disable the power fault interrupt. // if(ulFlags & USB_INT_POWER_FAULT) { HWREG(ulBase + USB_O_EPCIM) = 0; } // // Disable the ID pin detect interrupt. // if(ulFlags & USB_INT_MODE_DETECT) { HWREG(USB0_BASE + USB_O_IDVIM) = 0; } } #endif //***************************************************************************** // //! Enables the sources for USB interrupts. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies which interrupts to enable. //! //! This function will enable the USB controller's ability to generate the //! interrupts indicated by the \e ulFlags parameter. There are three //! groups of interrupt sources, IN Endpoints, OUT Endpoints, and //! general status changes, specified by \b USB_INT_HOST_IN, //! \b USB_INT_HOST_OUT, \b USB_INT_DEV_IN, \b USB_INT_DEV_OUT, and //! \b USB_STATUS. If \b USB_INT_ALL is specified then all interrupts will be //! enabled. //! //! \note A call must be made to enable the interrupt in the main interrupt //! controller to receive interrupts. The USBIntRegister() API performs this //! controller level interrupt enable. However if static interrupt handlers //! are used then then a call to IntEnable() must be made in order to allow any //! USB interrupts to occur. //! //! \note WARNING: This API cannot be used on endpoint numbers greater than //! endpoint 3 so USBIntEnableControl() or USBIntEnableEndpoint() should be //! used instead. //! //! \return None. // //***************************************************************************** #ifndef DEPRECATED void USBIntEnable(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulFlags & (~USB_INT_ALL)) == 0); // // If any transmit interrupts were enabled then write the transmit // interrupt settings out to the hardware. // if(ulFlags & (USB_INT_HOST_OUT | USB_INT_DEV_IN | USB_INT_EP0)) { HWREGH(ulBase + USB_O_TXIE) |= ulFlags & (USB_INT_HOST_OUT | USB_INT_DEV_IN | USB_INT_EP0); } // // If any receive interrupts were enabled then write the receive interrupt // settings out to the hardware. // if(ulFlags & (USB_INT_HOST_IN | USB_INT_DEV_OUT)) { HWREGH(ulBase + USB_O_RXIE) |= ((ulFlags & (USB_INT_HOST_IN | USB_INT_DEV_OUT)) >> USB_INT_RX_SHIFT); } // // If any general interrupts were enabled then write the general interrupt // settings out to the hardware. // if(ulFlags & USB_INT_STATUS) { HWREGB(ulBase + USB_O_IE) |= (ulFlags & USB_INT_STATUS) >> USB_INT_STATUS_SHIFT; } // // Enable the power fault interrupt. // if(ulFlags & USB_INT_POWER_FAULT) { HWREG(ulBase + USB_O_EPCIM) = USB_EPCIM_PF; } // // Enable the ID pin detect interrupt. // if(ulFlags & USB_INT_MODE_DETECT) { HWREG(USB0_BASE + USB_O_IDVIM) = USB_IDVIM_ID; } } #endif //***************************************************************************** // //! Disable control interrupts on a given USB controller. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies which control interrupts to disable. //! //! This function will disable the control interrupts for the USB controller //! specified by the \e ulBase parameter. The \e ulFlags parameter specifies //! which control interrupts to disable. The flags passed in the \e ulFlags //! parameters should be the definitions that start with \b USB_INTCTRL_* and //! not any other \b USB_INT flags. //! //! \return None. // //***************************************************************************** void USBIntDisableControl(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulFlags & ~(USB_INTCTRL_ALL)) == 0); // // If any general interrupts were disabled then write the general interrupt // settings out to the hardware. // if(ulFlags & USB_INTCTRL_STATUS) { HWREGB(ulBase + USB_O_IE) &= ~(ulFlags & USB_INTCTRL_STATUS); } // // Disable the power fault interrupt. // if(ulFlags & USB_INTCTRL_POWER_FAULT) { HWREG(ulBase + USB_O_EPCIM) = 0; } // // Disable the ID pin detect interrupt. // if(ulFlags & USB_INTCTRL_MODE_DETECT) { HWREG(USB0_BASE + USB_O_IDVIM) = 0; } } //***************************************************************************** // //! Enable control interrupts on a given USB controller. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies which control interrupts to enable. //! //! This function will enable the control interrupts for the USB controller //! specified by the \e ulBase parameter. The \e ulFlags parameter specifies //! which control interrupts to enable. The flags passed in the \e ulFlags //! parameters should be the definitions that start with \b USB_INTCTRL_* and //! not any other \b USB_INT flags. //! //! \return None. // //***************************************************************************** void USBIntEnableControl(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulFlags & (~USB_INTCTRL_ALL)) == 0); // // If any general interrupts were enabled then write the general interrupt // settings out to the hardware. // if(ulFlags & USB_INTCTRL_STATUS) { HWREGB(ulBase + USB_O_IE) |= ulFlags; } // // Enable the power fault interrupt. // if(ulFlags & USB_INTCTRL_POWER_FAULT) { HWREG(ulBase + USB_O_EPCIM) = USB_EPCIM_PF; } // // Enable the ID pin detect interrupt. // if(ulFlags & USB_INTCTRL_MODE_DETECT) { HWREG(USB0_BASE + USB_O_IDVIM) = USB_IDVIM_ID; } } //***************************************************************************** // //! Returns the control interrupt status on a given USB controller. //! //! \param ulBase specifies the USB module base address. //! //! This function will read control interrupt status for a USB controller. //! This call will return the current status for control interrupts only, the //! endpoint interrupt status is retrieved by calling USBIntStatusEndpoint(). //! The bit values returned should be compared against the \b USB_INTCTRL_* //! values. //! //! The following are the meanings of all \b USB_INCTRL_ flags and the modes //! for which they are valid. These values apply to any calls to //! USBIntStatusControl(), USBIntEnableControl(), and USBIntDisableConrol(). //! Some of these flags are only valid in the following modes as indicated in //! the parenthesis: Host, Device, and OTG. //! //! - \b USB_INTCTRL_ALL - A full mask of all control interrupt sources. //! - \b USB_INTCTRL_VBUS_ERR - A VBUS error has occurred (Host Only). //! - \b USB_INTCTRL_SESSION - Session Start Detected on A-side of cable //! (OTG Only). //! - \b USB_INTCTRL_SESSION_END - Session End Detected (Device Only) //! - \b USB_INTCTRL_DISCONNECT - Device Disconnect Detected (Host Only) //! - \b USB_INTCTRL_CONNECT - Device Connect Detected (Host Only) //! - \b USB_INTCTRL_SOF - Start of Frame Detected. //! - \b USB_INTCTRL_BABBLE - USB controller detected a device signaling past //! the end of a frame. (Host Only) //! - \b USB_INTCTRL_RESET - Reset signaling detected by device. (Device Only) //! - \b USB_INTCTRL_RESUME - Resume signaling detected. //! - \b USB_INTCTRL_SUSPEND - Suspend signaling detected by device (Device //! Only) //! - \b USB_INTCTRL_MODE_DETECT - OTG cable mode detection has completed //! (OTG Only) //! - \b USB_INTCTRL_POWER_FAULT - Power Fault detected. (Host Only) //! //! \note This call will clear the source of all of the control status //! interrupts. //! //! \return Returns the status of the control interrupts for a USB controller. // //***************************************************************************** unsigned long USBIntStatusControl(unsigned long ulBase) { unsigned long ulStatus; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Get the general interrupt status, these bits go into the upper 8 bits // of the returned value. // ulStatus = HWREGB(ulBase + USB_O_IS); // // Add the power fault status. // if(HWREG(ulBase + USB_O_EPCISC) & USB_EPCISC_PF) { // // Indicate a power fault was detected. // ulStatus |= USB_INTCTRL_POWER_FAULT; // // Clear the power fault interrupt. // HWREGB(ulBase + USB_O_EPCISC) |= USB_EPCISC_PF; } if(HWREG(USB0_BASE + USB_O_IDVISC) & USB_IDVRIS_ID) { // // Indicate a id detection was detected. // ulStatus |= USB_INTCTRL_MODE_DETECT; // // Clear the id detection interrupt. // HWREG(USB0_BASE + USB_O_IDVISC) |= USB_IDVRIS_ID; } // // Return the combined interrupt status. // return(ulStatus); } //***************************************************************************** // //! Disable endpoint interrupts on a given USB controller. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies which endpoint interrupts to disable. //! //! This function will disable endpoint interrupts for the USB controller //! specified by the \e ulBase parameter. The \e ulFlags parameter specifies //! which endpoint interrupts to disable. The flags passed in the \e ulFlags //! parameters should be the definitions that start with \b USB_INTEP_* and not //! any other \b USB_INT flags. //! //! \return None. // //***************************************************************************** void USBIntDisableEndpoint(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // If any transmit interrupts were disabled then write the transmit // interrupt settings out to the hardware. // HWREGH(ulBase + USB_O_TXIE) &= ~(ulFlags & (USB_INTEP_HOST_OUT | USB_INTEP_DEV_IN | USB_INTEP_0)); // // If any receive interrupts were disabled then write the receive interrupt // settings out to the hardware. // HWREGH(ulBase + USB_O_RXIE) &= ~((ulFlags & (USB_INTEP_HOST_IN | USB_INTEP_DEV_OUT)) >> USB_INTEP_RX_SHIFT); } //***************************************************************************** // //! Enable endpoint interrupts on a given USB controller. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies which endpoint interrupts to enable. //! //! This function will enable endpoint interrupts for the USB controller //! specified by the \e ulBase parameter. The \e ulFlags parameter specifies //! which endpoint interrupts to enable. The flags passed in the \e ulFlags //! parameters should be the definitions that start with \b USB_INTEP_* and not //! any other \b USB_INT flags. //! //! \return None. // //***************************************************************************** void USBIntEnableEndpoint(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Enable any transmit endpoint interrupts. // HWREGH(ulBase + USB_O_TXIE) |= ulFlags & (USB_INTEP_HOST_OUT | USB_INTEP_DEV_IN | USB_INTEP_0); // // Enable any receive endpoint interrupts. // HWREGH(ulBase + USB_O_RXIE) |= ((ulFlags & (USB_INTEP_HOST_IN | USB_INTEP_DEV_OUT)) >> USB_INTEP_RX_SHIFT); } //***************************************************************************** // //! Returns the endpoint interrupt status on a given USB controller. //! //! \param ulBase specifies the USB module base address. //! //! This function will read endpoint interrupt status for a USB controller. //! This call will return the current status for endpoint interrupts only, the //! control interrupt status is retrieved by calling USBIntStatusControl(). //! The bit values returned should be compared against the \b USB_INTEP_* //! values. These are grouped into classes for \b USB_INTEP_HOST_* and //! \b USB_INTEP_DEV_* values to handle both host and device modes with all //! endpoints. //! //! \note This call will clear the source of all of the endpoint interrupts. //! //! \return Returns the status of the endpoint interrupts for a USB controller. // //***************************************************************************** unsigned long USBIntStatusEndpoint(unsigned long ulBase) { unsigned long ulStatus; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Get the transmit interrupt status. // ulStatus = HWREGH(ulBase + USB_O_TXIS); ulStatus |= (HWREGH(ulBase + USB_O_RXIS) << USB_INTEP_RX_SHIFT); // // Return the combined interrupt status. // return(ulStatus); } //***************************************************************************** // //! Registers an interrupt handler for the USB controller. //! //! \param ulBase specifies the USB module base address. //! \param pfnHandler is a pointer to the function to be called when a USB //! interrupt occurs. //! //! This sets the handler to be called when a USB interrupt occurs. This will //! also enable the global USB interrupt in the interrupt controller. The //! specific desired USB interrupts must be enabled via a separate call to //! USBIntEnable(). It is the interrupt handler's responsibility to clear the //! interrupt sources via a calls to USBIntStatusControl() and //! USBIntStatusEndpoint(). //! //! \sa IntRegister() for important information about registering interrupt //! handlers. //! //! \return None. // //***************************************************************************** void USBIntRegister(unsigned long ulBase, void(*pfnHandler)(void)) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Register the interrupt handler. // IntRegister(INT_USB0, pfnHandler); // // Enable the USB interrupt. // IntEnable(INT_USB0); } //***************************************************************************** // //! Unregisters an interrupt handler for the USB controller. //! //! \param ulBase specifies the USB module base address. //! //! This function unregister the interrupt handler. This function will also //! disable the USB interrupt in the interrupt controller. //! //! \sa IntRegister() for important information about registering or //! unregistering interrupt handlers. //! //! \return None. // //***************************************************************************** void USBIntUnregister(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Unregister the interrupt handler. // IntUnregister(INT_USB0); // // Disable the CAN interrupt. // IntDisable(INT_USB0); } //***************************************************************************** // //! Returns the current status of an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! //! This function will return the status of a given endpoint. If any of these //! status bits need to be cleared, then these these values must be cleared by //! calling the USBDevEndpointStatusClear() or USBHostEndpointStatusClear() //! functions. //! //! The following are the status flags for host mode: //! //! - \b USB_HOST_IN_PID_ERROR - PID error on the given endpoint. //! - \b USB_HOST_IN_NOT_COMP - The device failed to respond to an IN request. //! - \b USB_HOST_IN_STALL - A stall was received on an IN endpoint. //! - \b USB_HOST_IN_DATA_ERROR - There was a CRC or bit-stuff error on an IN //! endpoint in Isochronous mode. //! - \b USB_HOST_IN_NAK_TO - NAKs received on this IN endpoint for more than //! the specified timeout period. //! - \b USB_HOST_IN_ERROR - Failed to communicate with a device using this IN //! endpoint. //! - \b USB_HOST_IN_FIFO_FULL - This IN endpoint's FIFO is full. //! - \b USB_HOST_IN_PKTRDY - Data packet ready on this IN endpoint. //! - \b USB_HOST_OUT_NAK_TO - NAKs received on this OUT endpoint for more than //! the specified timeout period. //! - \b USB_HOST_OUT_NOT_COMP - The device failed to respond to an OUT //! request. //! - \b USB_HOST_OUT_STALL - A stall was received on this OUT endpoint. //! - \b USB_HOST_OUT_ERROR - Failed to communicate with a device using this //! OUT endpoint. //! - \b USB_HOST_OUT_FIFO_NE - This endpoint's OUT FIFO is not empty. //! - \b USB_HOST_OUT_PKTPEND - The data transfer on this OUT endpoint has not //! completed. //! - \b USB_HOST_EP0_NAK_TO - NAKs received on endpoint zero for more than the //! specified timeout period. //! - \b USB_HOST_EP0_ERROR - The device failed to respond to a request on //! endpoint zero. //! - \b USB_HOST_EP0_IN_STALL - A stall was received on endpoint zero for an //! IN transaction. //! - \b USB_HOST_EP0_IN_PKTRDY - Data packet ready on endpoint zero for an IN //! transaction. //! //! The following are the status flags for device mode: //! //! - \b USB_DEV_OUT_SENT_STALL - A stall was sent on this OUT endpoint. //! - \b USB_DEV_OUT_DATA_ERROR - There was a CRC or bit-stuff error on an OUT //! endpoint. //! - \b USB_DEV_OUT_OVERRUN - An OUT packet was not loaded due to a full FIFO. //! - \b USB_DEV_OUT_FIFO_FULL - The OUT endpoint's FIFO is full. //! - \b USB_DEV_OUT_PKTRDY - There is a data packet ready in the OUT //! endpoint's FIFO. //! - \b USB_DEV_IN_NOT_COMP - A larger packet was split up, more data to come. //! - \b USB_DEV_IN_SENT_STALL - A stall was sent on this IN endpoint. //! - \b USB_DEV_IN_UNDERRUN - Data was requested on the IN endpoint and no //! data was ready. //! - \b USB_DEV_IN_FIFO_NE - The IN endpoint's FIFO is not empty. //! - \b USB_DEV_IN_PKTPEND - The data transfer on this IN endpoint has not //! completed. //! - \b USB_DEV_EP0_SETUP_END - A control transaction ended before Data End //! condition was sent. //! - \b USB_DEV_EP0_SENT_STALL - A stall was sent on endpoint zero. //! - \b USB_DEV_EP0_IN_PKTPEND - The data transfer on endpoint zero has not //! completed. //! - \b USB_DEV_EP0_OUT_PKTRDY - There is a data packet ready in endpoint //! zero's OUT FIFO. //! //! \return The current status flags for the endpoint depending on mode. // //***************************************************************************** unsigned long USBEndpointStatus(unsigned long ulBase, unsigned long ulEndpoint) { unsigned long ulStatus; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Get the TX portion of the endpoint status. // ulStatus = HWREGH(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRL1); // // Get the RX portion of the endpoint status. // ulStatus |= ((HWREGH(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRL1)) << USB_RX_EPSTATUS_SHIFT); // // Return the endpoint status. // return(ulStatus); } //***************************************************************************** // //! Clears the status bits in this endpoint in host mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags are the status bits that will be cleared. //! //! This function will clear the status of any bits that are passed in the //! \e ulFlags parameter. The \e ulFlags parameter can take the value returned //! from the USBEndpointStatus() call. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostEndpointStatusClear(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Clear the specified flags for the endpoint. // if(ulEndpoint == USB_EP_0) { HWREGB(ulBase + USB_O_CSRL0) &= ~ulFlags; } else { HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~ulFlags; HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~(ulFlags >> USB_RX_EPSTATUS_SHIFT); } } //***************************************************************************** // //! Clears the status bits in this endpoint in device mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags are the status bits that will be cleared. //! //! This function will clear the status of any bits that are passed in the //! \e ulFlags parameter. The \e ulFlags parameter can take the value returned //! from the USBEndpointStatus() call. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevEndpointStatusClear(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // If this is endpoint 0 then the bits have different meaning and map into // the TX memory location. // if(ulEndpoint == USB_EP_0) { // // Set the Serviced RxPktRdy bit to clear the RxPktRdy. // if(ulFlags & USB_DEV_EP0_OUT_PKTRDY) { HWREGB(ulBase + USB_O_CSRL0) |= USB_CSRL0_RXRDYC; } // // Set the serviced Setup End bit to clear the SetupEnd status. // if(ulFlags & USB_DEV_EP0_SETUP_END) { HWREGB(ulBase + USB_O_CSRL0) |= USB_CSRL0_SETENDC; } // // Clear the Sent Stall status flag. // if(ulFlags & USB_DEV_EP0_SENT_STALL) { HWREGB(ulBase + USB_O_CSRL0) &= ~(USB_DEV_EP0_SENT_STALL); } } else { // // Clear out any TX flags that were passed in. Only // USB_DEV_TX_SENT_STALL and USB_DEV_TX_UNDERRUN should be cleared. // HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~(ulFlags & (USB_DEV_TX_SENT_STALL | USB_DEV_TX_UNDERRUN)); // // Clear out valid RX flags that were passed in. Only // USB_DEV_RX_SENT_STALL, USB_DEV_RX_DATA_ERROR, and USB_DEV_RX_OVERRUN // should be cleared. // HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~((ulFlags & (USB_DEV_RX_SENT_STALL | USB_DEV_RX_DATA_ERROR | USB_DEV_RX_OVERRUN)) >> USB_RX_EPSTATUS_SHIFT); } } //***************************************************************************** // //! Sets the value data toggle on an endpoint in host mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint specifies the endpoint to reset the data toggle. //! \param bDataToggle specifies whether to set the state to DATA0 or DATA1. //! \param ulFlags specifies whether to set the IN or OUT endpoint. //! //! This function is used to force the state of the data toggle in host mode. //! If the value passed in the \e bDataToggle parameter is \b false, then the //! data toggle will be set to the DATA0 state, and if it is \b true it will be //! set to the DATA1 state. The \e ulFlags parameter can be \b USB_EP_HOST_IN //! or \b USB_EP_HOST_OUT to access the desired portion of this endpoint. The //! \e ulFlags parameter is ignored for endpoint zero. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostEndpointDataToggle(unsigned long ulBase, unsigned long ulEndpoint, tBoolean bDataToggle, unsigned long ulFlags) { unsigned long ulDataToggle; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // The data toggle defaults to DATA0. // ulDataToggle = 0; // // See if the data toggle should be set to DATA1. // if(bDataToggle) { // // Select the data toggle bit based on the endpoint. // if(ulEndpoint == USB_EP_0) { ulDataToggle = USB_CSRH0_DT; } else if(ulFlags == USB_EP_HOST_IN) { ulDataToggle = USB_RXCSRH1_DT; } else { ulDataToggle = USB_TXCSRH1_DT; } } // // Set the data toggle based on the endpoint. // if(ulEndpoint == USB_EP_0) { // // Set the write enable and the bit value for endpoint zero. // HWREGB(ulBase + USB_O_CSRH0) = ((HWREGB(ulBase + USB_O_CSRH0) & ~(USB_CSRH0_DTWE | USB_CSRH0_DT)) | (ulDataToggle | USB_CSRH0_DTWE)); } else if(ulFlags == USB_EP_HOST_IN) { // // Set the Write enable and the bit value for an IN endpoint. // HWREGB(ulBase + USB_O_RXCSRH1 + EP_OFFSET(ulEndpoint)) = ((HWREGB(ulBase + USB_O_RXCSRH1 + EP_OFFSET(ulEndpoint)) & ~(USB_RXCSRH1_DTWE | USB_RXCSRH1_DT)) | (ulDataToggle | USB_RXCSRH1_DTWE)); } else { // // Set the Write enable and the bit value for an OUT endpoint. // HWREGB(ulBase + USB_O_TXCSRH1 + EP_OFFSET(ulEndpoint)) = ((HWREGB(ulBase + USB_O_TXCSRH1 + EP_OFFSET(ulEndpoint)) & ~(USB_TXCSRH1_DTWE | USB_TXCSRH1_DT)) | (ulDataToggle | USB_TXCSRH1_DTWE)); } } //***************************************************************************** // //! Sets the Data toggle on an endpoint to zero. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint specifies the endpoint to reset the data toggle. //! \param ulFlags specifies whether to access the IN or OUT endpoint. //! //! This function will cause the controller to clear the data toggle for an //! endpoint. This call is not valid for endpoint zero and can be made with //! host or device controllers. //! //! The \e ulFlags parameter should be one of \b USB_EP_HOST_OUT, //! \b USB_EP_HOST_IN, \b USB_EP_DEV_OUT, or \b USB_EP_DEV_IN. //! //! \return None. // //***************************************************************************** void USBEndpointDataToggleClear(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the transmit or receive data toggle should be cleared. // if(ulFlags & (USB_EP_HOST_OUT | USB_EP_DEV_IN)) { HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_TXCSRL1_CLRDT; } else { HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_RXCSRL1_CLRDT; } } //***************************************************************************** // //! Stalls the specified endpoint in device mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint specifies the endpoint to stall. //! \param ulFlags specifies whether to stall the IN or OUT endpoint. //! //! This function will cause to endpoint number passed in to go into a stall //! condition. If the \e ulFlags parameter is \b USB_EP_DEV_IN then the stall //! will be issued on the IN portion of this endpoint. If the \e ulFlags //! parameter is \b USB_EP_DEV_OUT then the stall will be issued on the OUT //! portion of this endpoint. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevEndpointStall(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulFlags & ~(USB_EP_DEV_IN | USB_EP_DEV_OUT)) == 0) ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Determine how to stall this endpoint. // if(ulEndpoint == USB_EP_0) { // // Perform a stall on endpoint zero. // HWREGB(ulBase + USB_O_CSRL0) |= (USB_CSRL0_STALL | USB_CSRL0_RXRDYC); } else if(ulFlags == USB_EP_DEV_IN) { // // Perform a stall on an IN endpoint. // HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_TXCSRL1_STALL; } else { // // Perform a stall on an OUT endpoint. // HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_RXCSRL1_STALL; } } //***************************************************************************** // //! Clears the stall condition on the specified endpoint in device mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint specifies which endpoint to remove the stall condition. //! \param ulFlags specifies whether to remove the stall condition from the IN //! or the OUT portion of this endpoint. //! //! This function will cause the endpoint number passed in to exit the stall //! condition. If the \e ulFlags parameter is \b USB_EP_DEV_IN then the stall //! will be cleared on the IN portion of this endpoint. If the \e ulFlags //! parameter is \b USB_EP_DEV_OUT then the stall will be cleared on the OUT //! portion of this endpoint. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevEndpointStallClear(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); ASSERT((ulFlags & ~(USB_EP_DEV_IN | USB_EP_DEV_OUT)) == 0) // // Determine how to clear the stall on this endpoint. // if(ulEndpoint == USB_EP_0) { // // Clear the stall on endpoint zero. // HWREGB(ulBase + USB_O_CSRL0) &= ~USB_CSRL0_STALLED; } else if(ulFlags == USB_EP_DEV_IN) { // // Clear the stall on an IN endpoint. // HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~(USB_TXCSRL1_STALL | USB_TXCSRL1_STALLED); // // Reset the data toggle. // HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_TXCSRL1_CLRDT; } else { // // Clear the stall on an OUT endpoint. // HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~(USB_RXCSRL1_STALL | USB_RXCSRL1_STALLED); // // Reset the data toggle. // HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_RXCSRL1_CLRDT; } } //***************************************************************************** // //! Connects the USB controller to the bus in device mode. //! //! \param ulBase specifies the USB module base address. //! //! This function will cause the soft connect feature of the USB controller to //! be enabled. Call USBDisconnect() to remove the USB device from the bus. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevConnect(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Enable connection to the USB bus. // HWREGB(ulBase + USB_O_POWER) |= USB_POWER_SOFTCONN; } //***************************************************************************** // //! Removes the USB controller from the bus in device mode. //! //! \param ulBase specifies the USB module base address. //! //! This function will cause the soft connect feature of the USB controller to //! remove the device from the USB bus. A call to USBDevConnect() is needed to //! reconnect to the bus. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevDisconnect(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Disable connection to the USB bus. // HWREGB(ulBase + USB_O_POWER) &= (~USB_POWER_SOFTCONN); } //***************************************************************************** // //! Sets the address in device mode. //! //! \param ulBase specifies the USB module base address. //! \param ulAddress is the address to use for a device. //! //! This function will set the device address on the USB bus. This address was //! likely received via a SET ADDRESS command from the host controller. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevAddrSet(unsigned long ulBase, unsigned long ulAddress) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Set the function address in the correct location. // HWREGB(ulBase + USB_O_FADDR) = (unsigned char)ulAddress; } //***************************************************************************** // //! Returns the current device address in device mode. //! //! \param ulBase specifies the USB module base address. //! //! This function will return the current device address. This address was set //! by a call to USBDevAddrSet(). //! //! \note This function should only be called in device mode. //! //! \return The current device address. // //***************************************************************************** unsigned long USBDevAddrGet(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Return the function address. // return(HWREGB(ulBase + USB_O_FADDR)); } //***************************************************************************** // //! Sets the base configuration for a host endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulMaxPayload is the maximum payload for this endpoint. //! \param ulNAKPollInterval is the either the NAK timeout limit or the polling //! interval depending on the type of endpoint. //! \param ulTargetEndpoint is the endpoint that the host endpoint is //! targeting. //! \param ulFlags are used to configure other endpoint settings. //! //! This function will set the basic configuration for the transmit or receive //! portion of an endpoint in host mode. The \e ulFlags parameter determines //! some of the configuration while the other parameters provide the rest. The //! \e ulFlags parameter determines whether this is an IN endpoint //! (USB_EP_HOST_IN or USB_EP_DEV_IN) or an OUT endpoint (USB_EP_HOST_OUT or //! USB_EP_DEV_OUT), whether this is a Full speed endpoint (USB_EP_SPEED_FULL) //! or a Low speed endpoint (USB_EP_SPEED_LOW). //! //! The \b USB_EP_MODE_ flags control the type of the endpoint. //! - \b USB_EP_MODE_CTRL is a control endpoint. //! - \b USB_EP_MODE_ISOC is an isochronous endpoint. //! - \b USB_EP_MODE_BULK is a bulk endpoint. //! - \b USB_EP_MODE_INT is an interrupt endpoint. //! //! The \e ulNAKPollInterval parameter has different meanings based on the //! \b USB_EP_MODE value and whether or not this call is being made for //! endpoint zero or another endpoint. For endpoint zero or any Bulk //! endpoints, this value always indicates the number of frames to allow a //! device to NAK before considering it a timeout. If this endpoint is an //! isochronous or interrupt endpoint, this value is the polling interval for //! this endpoint. //! //! For interrupt endpoints the polling interval is simply the number of //! frames between polling an interrupt endpoint. For isochronous endpoints //! this value represents a polling interval of 2 ^ (\e ulNAKPollInterval - 1) //! frames. When used as a NAK timeout, the \e ulNAKPollInterval value //! specifies 2 ^ (\e ulNAKPollInterval - 1) frames before issuing a time out. //! There are two special time out values that can be specified when setting //! the \e ulNAKPollInterval value. The first is \b MAX_NAK_LIMIT which is the //! maximum value that can be passed in this variable. The other is //! \b DISABLE_NAK_LIMIT which indicates that there should be no limit on the //! number of NAKs. //! //! The \b USB_EP_DMA_MODE_ flags enables the type of DMA used to access the //! endpoint's data FIFOs. The choice of the DMA mode depends on how the DMA //! controller is configured and how it is being used. See the ``Using USB //! with the uDMA Controller'' section for more information on DMA //! configuration. //! //! When configuring the OUT portion of an endpoint, the \b USB_EP_AUTO_SET bit //! is specified to cause the transmission of data on the USB bus to start //! as soon as the number of bytes specified by \e ulMaxPayload have been //! written into the OUT FIFO for this endpoint. //! //! When configuring the IN portion of an endpoint, the \b USB_EP_AUTO_REQUEST //! bit can be specified to trigger the request for more data once the FIFO has //! been drained enough to fit \e ulMaxPayload bytes. The \b USB_EP_AUTO_CLEAR //! bit can be used to clear the data packet ready flag automatically once the //! data has been read from the FIFO. If this is not used, this flag must be //! manually cleared via a call to USBDevEndpointStatusClear() or //! USBHostEndpointStatusClear(). //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostEndpointConfig(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulMaxPayload, unsigned long ulNAKPollInterval, unsigned long ulTargetEndpoint, unsigned long ulFlags) { unsigned long ulRegister; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); ASSERT(ulNAKPollInterval <= MAX_NAK_LIMIT); // // Endpoint zero is configured differently than the other endpoints, so see // if this is endpoint zero. // if(ulEndpoint == USB_EP_0) { // // Set the NAK timeout. // HWREGB(ulBase + USB_O_NAKLMT) = ulNAKPollInterval; // // Set the transfer type information. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TYPE0) = ((ulFlags & USB_EP_SPEED_FULL) ? USB_TYPE0_SPEED_FULL : USB_TYPE0_SPEED_LOW); } else { // // Start with the target endpoint. // ulRegister = ulTargetEndpoint; // // Set the speed for the device using this endpoint. // if(ulFlags & USB_EP_SPEED_FULL) { ulRegister |= USB_TXTYPE1_SPEED_FULL; } else { ulRegister |= USB_TXTYPE1_SPEED_LOW; } // // Set the protocol for the device using this endpoint. // switch(ulFlags & USB_EP_MODE_MASK) { // // The bulk protocol is being used. // case USB_EP_MODE_BULK: { ulRegister |= USB_TXTYPE1_PROTO_BULK; break; } // // The isochronous protocol is being used. // case USB_EP_MODE_ISOC: { ulRegister |= USB_TXTYPE1_PROTO_ISOC; break; } // // The interrupt protocol is being used. // case USB_EP_MODE_INT: { ulRegister |= USB_TXTYPE1_PROTO_INT; break; } // // The control protocol is being used. // case USB_EP_MODE_CTRL: { ulRegister |= USB_TXTYPE1_PROTO_CTRL; break; } } // // See if the transmit or receive endpoint is being configured. // if(ulFlags & USB_EP_HOST_OUT) { // // Set the transfer type information. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXTYPE1) = ulRegister; // // Set the NAK timeout or polling interval. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXINTERVAL1) = ulNAKPollInterval; // // Set the Maximum Payload per transaction. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXMAXP1) = ulMaxPayload; // // Set the transmit control value to zero. // ulRegister = 0; // // Allow auto setting of TxPktRdy when max packet size has been // loaded into the FIFO. // if(ulFlags & USB_EP_AUTO_SET) { ulRegister |= USB_TXCSRH1_AUTOSET; } // // Configure the DMA Mode. // if(ulFlags & USB_EP_DMA_MODE_1) { ulRegister |= USB_TXCSRH1_DMAEN | USB_TXCSRH1_DMAMOD; } else if(ulFlags & USB_EP_DMA_MODE_0) { ulRegister |= USB_TXCSRH1_DMAEN; } // // Write out the transmit control value. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRH1) = (unsigned char)ulRegister; } else { // // Set the transfer type information. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXTYPE1) = ulRegister; // // Set the NAK timeout or polling interval. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXINTERVAL1) = ulNAKPollInterval; // // Set the receive control value to zero. // ulRegister = 0; // // Allow auto clearing of RxPktRdy when packet of size max packet // has been unloaded from the FIFO. // if(ulFlags & USB_EP_AUTO_CLEAR) { ulRegister |= USB_RXCSRH1_AUTOCL; } // // Configure the DMA Mode. // if(ulFlags & USB_EP_DMA_MODE_1) { ulRegister |= USB_RXCSRH1_DMAEN | USB_RXCSRH1_DMAMOD; } else if(ulFlags & USB_EP_DMA_MODE_0) { ulRegister |= USB_RXCSRH1_DMAEN; } // // Write out the receive control value. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRH1) = (unsigned char)ulRegister; } } } //***************************************************************************** // //! Sets the configuration for an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulMaxPacketSize is the maximum packet size for this endpoint. //! \param ulFlags are used to configure other endpoint settings. //! //! This function will set the basic configuration for an endpoint in device //! mode. Endpoint zero does not have a dynamic configuration, so this //! function should not be called for endpoint zero. The \e ulFlags parameter //! determines some of the configuration while the other parameters provide the //! rest. //! //! The \b USB_EP_MODE_ flags define what the type is for the given endpoint. //! //! - \b USB_EP_MODE_CTRL is a control endpoint. //! - \b USB_EP_MODE_ISOC is an isochronous endpoint. //! - \b USB_EP_MODE_BULK is a bulk endpoint. //! - \b USB_EP_MODE_INT is an interrupt endpoint. //! //! The \b USB_EP_DMA_MODE_ flags determines the type of DMA access to the //! endpoint data FIFOs. The choice of the DMA mode depends on how the DMA //! controller is configured and how it is being used. See the ``Using USB //! with the uDMA Controller'' section for more information on DMA //! configuration. //! //! When configuring an IN endpoint, the \b USB_EP_AUTO_SET bit can be //! specified to cause the automatic transmission of data on the USB bus as //! soon as \e ulMaxPacketSize bytes of data are written into the FIFO for //! this endpoint. This is commonly used with DMA as no interaction is //! required to start the transmission of data. //! //! When configuring an OUT endpoint, the \b USB_EP_AUTO_REQUEST bit is //! specified to trigger the request for more data once the FIFO has been //! drained enough to receive \e ulMaxPacketSize more bytes of data. Also for //! OUT endpoints, the \b USB_EP_AUTO_CLEAR bit can be used to clear the data //! packet ready flag automatically once the data has been read from the FIFO. //! If this is not used, this flag must be manually cleared via a call to //! USBDevEndpointStatusClear(). Both of these settings can be used to remove //! the need for extra calls when using the controller in DMA mode. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevEndpointConfigSet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulMaxPacketSize, unsigned long ulFlags) { unsigned long ulRegister; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Determine if a transmit or receive endpoint is being configured. // if(ulFlags & USB_EP_DEV_IN) { // // Set the maximum packet size. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXMAXP1) = ulMaxPacketSize; // // The transmit control value is zero unless options are enabled. // ulRegister = 0; // // Allow auto setting of TxPktRdy when max packet size has been loaded // into the FIFO. // if(ulFlags & USB_EP_AUTO_SET) { ulRegister |= USB_TXCSRH1_AUTOSET; } // // Configure the DMA mode. // if(ulFlags & USB_EP_DMA_MODE_1) { ulRegister |= USB_TXCSRH1_DMAEN | USB_TXCSRH1_DMAMOD; } else if(ulFlags & USB_EP_DMA_MODE_0) { ulRegister |= USB_TXCSRH1_DMAEN; } // // Enable isochronous mode if requested. // if((ulFlags & USB_EP_MODE_MASK) == USB_EP_MODE_ISOC) { ulRegister |= USB_TXCSRH1_ISO; } // // Write the transmit control value. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRH1) = (unsigned char)ulRegister; // // Reset the Data toggle to zero. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRL1) = USB_TXCSRL1_CLRDT; } else { // // Set the MaxPacketSize. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXMAXP1) = ulMaxPacketSize; // // The receive control value is zero unless options are enabled. // ulRegister = 0; // // Allow auto clearing of RxPktRdy when packet of size max packet // has been unloaded from the FIFO. // if(ulFlags & USB_EP_AUTO_CLEAR) { ulRegister = USB_RXCSRH1_AUTOCL; } // // Configure the DMA mode. // if(ulFlags & USB_EP_DMA_MODE_1) { ulRegister |= USB_RXCSRH1_DMAEN | USB_RXCSRH1_DMAMOD; } else if(ulFlags & USB_EP_DMA_MODE_0) { ulRegister |= USB_RXCSRH1_DMAEN; } // // Enable isochronous mode if requested. // if((ulFlags & USB_EP_MODE_MASK) == USB_EP_MODE_ISOC) { ulRegister |= USB_RXCSRH1_ISO; } // // Write the receive control value. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRH1) = (unsigned char)ulRegister; // // Reset the Data toggle to zero. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRL1) = USB_RXCSRL1_CLRDT; } } //***************************************************************************** // //! Gets the current configuration for an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param pulMaxPacketSize is a pointer which will be written with the //! maximum packet size for this endpoint. //! \param pulFlags is a pointer which will be written with the current //! endpoint settings. On entry to the function, this pointer must contain //! either \b USB_EP_DEV_IN or \b USB_EP_DEV_OUT to indicate whether the IN or //! OUT endpoint is to be queried. //! //! This function will return the basic configuration for an endpoint in device //! mode. The values returned in \e *pulMaxPacketSize and \e *pulFlags are //! equivalent to the \e ulMaxPacketSize and \e ulFlags previously passed to //! USBDevEndpointConfigSet() for this endpoint. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevEndpointConfigGet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long *pulMaxPacketSize, unsigned long *pulFlags) { unsigned long ulRegister; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT(pulMaxPacketSize && pulFlags); ASSERT((ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Determine if a transmit or receive endpoint is being queried. // if(*pulFlags & USB_EP_DEV_IN) { // // Clear the flags other than the direction bit. // *pulFlags = USB_EP_DEV_IN; // // Get the maximum packet size. // *pulMaxPacketSize = (unsigned long)HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXMAXP1); // // Get the current transmit control register value. // ulRegister = (unsigned long)HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRH1); // // Are we allowing auto setting of TxPktRdy when max packet size has // been loaded into the FIFO? // if(ulRegister & USB_TXCSRH1_AUTOSET) { *pulFlags |= USB_EP_AUTO_SET; } // // Get the DMA mode. // if(ulRegister & USB_TXCSRH1_DMAEN) { if(ulRegister & USB_TXCSRH1_DMAMOD) { *pulFlags |= USB_EP_DMA_MODE_1; } else { *pulFlags |= USB_EP_DMA_MODE_0; } } // // Are we in isochronous mode? // if(ulRegister & USB_TXCSRH1_ISO) { *pulFlags |= USB_EP_MODE_ISOC; } else { // // The hardware doesn't differentiate between bulk, interrupt // and control mode for the endpoint so we just set something // that isn't isochronous. This ensures that anyone modifying // the returned flags in preparation for a call to // USBDevEndpointConfigSet will not see an unexpected mode change. // If they decode the returned mode, however, they may be in for // a surprise. // *pulFlags |= USB_EP_MODE_BULK; } } else { // // Clear the flags other than the direction bit. // *pulFlags = USB_EP_DEV_OUT; // // Get the MaxPacketSize. // *pulMaxPacketSize = (unsigned long)HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXMAXP1); // // Get the current receive control register value. // ulRegister = (unsigned long)HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRH1); // // Are we allowing auto clearing of RxPktRdy when packet of size max // packet has been unloaded from the FIFO? // if(ulRegister & USB_RXCSRH1_AUTOCL) { *pulFlags |= USB_EP_AUTO_CLEAR; } // // Get the DMA mode. // if(ulRegister & USB_RXCSRH1_DMAEN) { if(ulRegister & USB_RXCSRH1_DMAMOD) { *pulFlags |= USB_EP_DMA_MODE_1; } else { *pulFlags |= USB_EP_DMA_MODE_0; } } // // Are we in isochronous mode? // if(ulRegister & USB_RXCSRH1_ISO) { *pulFlags |= USB_EP_MODE_ISOC; } else { // // The hardware doesn't differentiate between bulk, interrupt // and control mode for the endpoint so we just set something // that isn't isochronous. This ensures that anyone modifying // the returned flags in preparation for a call to // USBDevEndpointConfigSet will not see an unexpected mode change. // If they decode the returned mode, however, they may be in for // a surprise. // *pulFlags |= USB_EP_MODE_BULK; } } } //***************************************************************************** // //! Sets the FIFO configuration for an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFIFOAddress is the starting address for the FIFO. //! \param ulFIFOSize is the size of the FIFO in bytes. //! \param ulFlags specifies what information to set in the FIFO configuration. //! //! This function will set the starting FIFO RAM address and size of the FIFO //! for a given endpoint. Endpoint zero does not have a dynamically //! configurable FIFO so this function should not be called for endpoint zero. //! The \e ulFIFOSize parameter should be one of the values in the //! \b USB_FIFO_SZ_ values. If the endpoint is going to use double buffering //! it should use the values with the \b _DB at the end of the value. For //! example, use \b USB_FIFO_SZ_16_DB to configure an endpoint to have a 16 //! byte double buffered FIFO. If a double buffered FIFO is used, then the //! actual size of the FIFO will be twice the size indicated by the //! \e ulFIFOSize parameter. This means that the \b USB_FIFO_SZ_16_DB value //! will use 32 bytes of the USB controller's FIFO memory. //! //! The \e ulFIFOAddress value should be a multiple of 8 bytes and directly //! indicates the starting address in the USB controller's FIFO RAM. For //! example, a value of 64 indicates that the FIFO should start 64 bytes into //! the USB controller's FIFO memory. The \e ulFlags value specifies whether //! the endpoint's OUT or IN FIFO should be configured. If in host mode, use //! \b USB_EP_HOST_OUT or \b USB_EP_HOST_IN, and if in device mode use //! \b USB_EP_DEV_OUT or \b USB_EP_DEV_IN. //! //! \return None. // //***************************************************************************** void USBFIFOConfigSet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFIFOAddress, unsigned long ulFIFOSize, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the transmit or receive FIFO is being configured. // if(ulFlags & (USB_EP_HOST_OUT | USB_EP_DEV_IN)) { // // Set the transmit FIFO location and size for this endpoint. // USBIndexWrite(ulBase, ulEndpoint >> 4, USB_O_TXFIFOSZ, ulFIFOSize, 1); USBIndexWrite(ulBase, ulEndpoint >> 4, USB_O_TXFIFOADD, ulFIFOAddress >> 3, 2); } else { // // Set the receive FIFO location and size for this endpoint. // USBIndexWrite(ulBase, ulEndpoint >> 4, USB_O_RXFIFOSZ, ulFIFOSize, 1); USBIndexWrite(ulBase, ulEndpoint >> 4, USB_O_RXFIFOADD, ulFIFOAddress >> 3, 2); } } //***************************************************************************** // //! Returns the FIFO configuration for an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param pulFIFOAddress is the starting address for the FIFO. //! \param pulFIFOSize is the size of the FIFO in bytes. //! \param ulFlags specifies what information to retrieve from the FIFO //! configuration. //! //! This function will return the starting address and size of the FIFO for a //! given endpoint. Endpoint zero does not have a dynamically configurable //! FIFO so this function should not be called for endpoint zero. The //! \e ulFlags parameter specifies whether the endpoint's OUT or IN FIFO should //! be read. If in host mode, the \e ulFlags parameter should be //! \b USB_EP_HOST_OUT or \b USB_EP_HOST_IN, and if in device mode the //! \e ulFlags parameter should be either \b USB_EP_DEV_OUT or //! \b USB_EP_DEV_IN. //! //! \return None. // //***************************************************************************** void USBFIFOConfigGet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long *pulFIFOAddress, unsigned long *pulFIFOSize, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the transmit or receive FIFO is being configured. // if(ulFlags & (USB_EP_HOST_OUT | USB_EP_DEV_IN)) { // // Get the transmit FIFO location and size for this endpoint. // *pulFIFOAddress = (USBIndexRead(ulBase, ulEndpoint >> 4, (unsigned long)USB_O_TXFIFOADD, 2)) << 3; *pulFIFOSize = USBIndexRead(ulBase, ulEndpoint >> 4, (unsigned long)USB_O_TXFIFOSZ, 1); } else { // // Get the receive FIFO location and size for this endpoint. // *pulFIFOAddress = (USBIndexRead(ulBase, ulEndpoint >> 4, (unsigned long)USB_O_RXFIFOADD, 2)) << 3; *pulFIFOSize = USBIndexRead(ulBase, ulEndpoint >> 4, (unsigned long)USB_O_RXFIFOSZ, 1); } } //***************************************************************************** // //! Enable DMA on a given endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags specifies which direction and what mode to use when enabling //! DMA. //! //! This function will enable DMA on a given endpoint and set the mode according //! to the values in the \e ulFlags parameter. The \e ulFlags parameter should //! have \b USB_EP_DEV_IN or \b USB_EP_DEV_OUT set. //! //! \return None. // //***************************************************************************** void USBEndpointDMAEnable(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // See if the transmit DMA is being enabled. // if(ulFlags & USB_EP_DEV_IN) { // // Enable DMA on the transmit end point. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRH1) |= USB_TXCSRH1_DMAEN; } else { // // Enable DMA on the receive end point. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRH1) |= USB_RXCSRH1_DMAEN; } } //***************************************************************************** // //! Disable DMA on a given endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags specifies which direction to disable. //! //! This function will disable DMA on a given end point to allow non-DMA //! USB transactions to generate interrupts normally. The ulFlags should be //! \b USB_EP_DEV_IN or \b USB_EP_DEV_OUT all other bits are ignored. //! //! \return None. // //***************************************************************************** void USBEndpointDMADisable(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // If this was a request to disable DMA on the IN portion of the end point // then handle it. // if(ulFlags & USB_EP_DEV_IN) { // // Just disable DMA leave the mode setting. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_TXCSRH1) &= ~USB_TXCSRH1_DMAEN; } else { // // Just disable DMA leave the mode setting. // HWREGB(ulBase + EP_OFFSET(ulEndpoint) + USB_O_RXCSRH1) &= ~USB_RXCSRH1_DMAEN; } } //***************************************************************************** // //! Determine the number of bytes of data available in a given endpoint's FIFO. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! //! This function will return the number of bytes of data currently available //! in the FIFO for the given receive (OUT) endpoint. It may be used prior to //! calling USBEndpointDataGet() to determine the size of buffer required to //! hold the newly-received packet. //! //! \return This call will return the number of bytes available in a given //! endpoint FIFO. // //***************************************************************************** unsigned long USBEndpointDataAvail(unsigned long ulBase, unsigned long ulEndpoint) { unsigned long ulRegister; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Get the address of the receive status register to use, based on the // endpoint. // if(ulEndpoint == USB_EP_0) { ulRegister = USB_O_CSRL0; } else { ulRegister = USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint); } // // Is there a packet ready in the FIFO? // if((HWREGH(ulBase + ulRegister) & USB_CSRL0_RXRDY) == 0) { return(0); } // // Return the byte count in the FIFO. // return(HWREGH(ulBase + USB_O_COUNT0 + ulEndpoint)); } //***************************************************************************** // //! Retrieves data from the given endpoint's FIFO. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param pucData is a pointer to the data area used to return the data from //! the FIFO. //! \param pulSize is initially the size of the buffer passed into this call //! via the \e pucData parameter. It will be set to the amount of data //! returned in the buffer. //! //! This function will return the data from the FIFO for the given endpoint. //! The \e pulSize parameter should indicate the size of the buffer passed in //! the \e pulData parameter. The data in the \e pulSize parameter will be //! changed to match the amount of data returned in the \e pucData parameter. //! If a zero byte packet was received this call will not return a error but //! will instead just return a zero in the \e pulSize parameter. The only //! error case occurs when there is no data packet available. //! //! \return This call will return 0, or -1 if no packet was received. // //***************************************************************************** long USBEndpointDataGet(unsigned long ulBase, unsigned long ulEndpoint, unsigned char *pucData, unsigned long *pulSize) { unsigned long ulRegister, ulByteCount, ulFIFO; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Get the address of the receive status register to use, based on the // endpoint. // if(ulEndpoint == USB_EP_0) { ulRegister = USB_O_CSRL0; } else { ulRegister = USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint); } // // Don't allow reading of data if the RxPktRdy bit is not set. // if((HWREGH(ulBase + ulRegister) & USB_CSRL0_RXRDY) == 0) { // // Can't read the data because none is available. // *pulSize = 0; // // Return a failure since there is no data to read. // return(-1); } // // Get the byte count in the FIFO. // ulByteCount = HWREGH(ulBase + USB_O_COUNT0 + ulEndpoint); // // Determine how many bytes we will actually copy. // ulByteCount = (ulByteCount < *pulSize) ? ulByteCount : *pulSize; // // Return the number of bytes we are going to read. // *pulSize = ulByteCount; // // Calculate the FIFO address. // ulFIFO = ulBase + USB_O_FIFO0 + (ulEndpoint >> 2); // // Read the data out of the FIFO. // for(; ulByteCount > 0; ulByteCount--) { // // Read a byte at a time from the FIFO. // *pucData++ = HWREGB(ulFIFO); } // // Success. // return(0); } //***************************************************************************** // //! Acknowledge that data was read from the given endpoint's FIFO in device //! mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param bIsLastPacket indicates if this is the last packet. //! //! This function acknowledges that the data was read from the endpoint's FIFO. //! The \e bIsLastPacket parameter is set to a \b true value if this is the //! last in a series of data packets on endpoint zero. The \e bIsLastPacket //! parameter is not used for endpoints other than endpoint zero. This call //! can be used if processing is required between reading the data and //! acknowledging that the data has been read. //! //! \note This function should only be called in device mode. //! //! \return None. // //***************************************************************************** void USBDevEndpointDataAck(unsigned long ulBase, unsigned long ulEndpoint, tBoolean bIsLastPacket) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Determine which endpoint is being acked. // if(ulEndpoint == USB_EP_0) { // // Clear RxPktRdy, and optionally DataEnd, on endpoint zero. // HWREGB(ulBase + USB_O_CSRL0) = USB_CSRL0_RXRDYC | (bIsLastPacket ? USB_CSRL0_DATAEND : 0); } else { // // Clear RxPktRdy on all other endpoints. // HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~(USB_RXCSRL1_RXRDY); } } //***************************************************************************** // //! Acknowledge that data was read from the given endpoint's FIFO in host //! mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! //! This function acknowledges that the data was read from the endpoint's FIFO. //! This call is used if processing is required between reading the data and //! acknowledging that the data has been read. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostEndpointDataAck(unsigned long ulBase, unsigned long ulEndpoint) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Clear RxPktRdy. // if(ulEndpoint == USB_EP_0) { HWREGB(ulBase + USB_O_CSRL0) &= ~USB_CSRL0_RXRDY; } else { HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) &= ~(USB_RXCSRL1_RXRDY); } } //***************************************************************************** // //! Puts data into the given endpoint's FIFO. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param pucData is a pointer to the data area used as the source for the //! data to put into the FIFO. //! \param ulSize is the amount of data to put into the FIFO. //! //! This function will put the data from the \e pucData parameter into the FIFO //! for this endpoint. If a packet is already pending for transmission then //! this call will not put any of the data into the FIFO and will return -1. //! Care should be taken to not write more data than can fit into the FIFO //! allocated by the call to USBFIFOConfig(). //! //! \return This call will return 0 on success, or -1 to indicate that the FIFO //! is in use and cannot be written. // //***************************************************************************** long USBEndpointDataPut(unsigned long ulBase, unsigned long ulEndpoint, unsigned char *pucData, unsigned long ulSize) { unsigned long ulFIFO; unsigned char ucTxPktRdy; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Get the bit position of TxPktRdy based on the endpoint. // if(ulEndpoint == USB_EP_0) { ucTxPktRdy = USB_CSRL0_TXRDY; } else { ucTxPktRdy = USB_TXCSRL1_TXRDY; } // // Don't allow transmit of data if the TxPktRdy bit is already set. // if(HWREGB(ulBase + USB_O_CSRL0 + ulEndpoint) & ucTxPktRdy) { return(-1); } // // Calculate the FIFO address. // ulFIFO = ulBase + USB_O_FIFO0 + (ulEndpoint >> 2); // // Write the data to the FIFO. // for(; ulSize > 0; ulSize--) { HWREGB(ulFIFO) = *pucData++; } // // Success. // return(0); } //***************************************************************************** // //! Starts the transfer of data from an endpoint's FIFO. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulTransType is set to indicate what type of data is being sent. //! //! This function will start the transfer of data from the FIFO for a given //! endpoint. This is necessary if the \b USB_EP_AUTO_SET bit was not enabled //! for the endpoint. Setting the \e ulTransType parameter will allow the //! appropriate signaling on the USB bus for the type of transaction being //! requested. The \e ulTransType parameter should be one of the following: //! //! - USB_TRANS_OUT for OUT transaction on any endpoint in host mode. //! - USB_TRANS_IN for IN transaction on any endpoint in device mode. //! - USB_TRANS_IN_LAST for the last IN transactions on endpoint zero in a //! sequence of IN transactions. //! - USB_TRANS_SETUP for setup transactions on endpoint zero. //! - USB_TRANS_STATUS for status results on endpoint zero. //! //! \return This call will return 0 on success, or -1 if a transmission is //! already in progress. // //***************************************************************************** long USBEndpointDataSend(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulTransType) { unsigned long ulTxPktRdy; // // CHeck the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Get the bit position of TxPktRdy based on the endpoint. // if(ulEndpoint == USB_EP_0) { ulTxPktRdy = ulTransType & 0xff; } else { ulTxPktRdy = (ulTransType >> 8) & 0xff; } // // Don't allow transmit of data if the TxPktRdy bit is already set. // if(HWREGB(ulBase + USB_O_CSRL0 + ulEndpoint) & USB_CSRL0_TXRDY) { return(-1); } // // Set TxPktRdy in order to send the data. // HWREGB(ulBase + USB_O_CSRL0 + ulEndpoint) = ulTxPktRdy; // // Success. // return(0); } //***************************************************************************** // //! Forces a flush of an endpoint's FIFO. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags specifies if the IN or OUT endpoint should be accessed. //! //! This function will force the controller to flush out the data in the FIFO. //! The function can be called with either host or device controllers and //! requires the \e ulFlags parameter be one of \b USB_EP_HOST_OUT, //! \b USB_EP_HOST_IN, \b USB_EP_DEV_OUT, or \b USB_EP_DEV_IN. //! //! \return None. // //***************************************************************************** void USBFIFOFlush(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Endpoint zero has a different register set for FIFO flushing. // if(ulEndpoint == USB_EP_0) { // // Nothing in the FIFO if neither of these bits are set. // if((HWREGB(ulBase + USB_O_CSRL0) & (USB_CSRL0_RXRDY | USB_CSRL0_TXRDY)) != 0) { // // Hit the Flush FIFO bit. // HWREGB(ulBase + USB_O_CSRH0) = USB_CSRH0_FLUSH; } } else { // // Only reset the IN or OUT FIFO. // if(ulFlags & (USB_EP_HOST_OUT | USB_EP_DEV_IN)) { // // Make sure the FIFO is not empty. // if(HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) & USB_TXCSRL1_TXRDY) { // // Hit the Flush FIFO bit. // HWREGB(ulBase + USB_O_TXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_TXCSRL1_FLUSH; } } else { // // Make sure that the FIFO is not empty. // if(HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) & USB_RXCSRL1_RXRDY) { // // Hit the Flush FIFO bit. // HWREGB(ulBase + USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint)) |= USB_RXCSRL1_FLUSH; } } } } //***************************************************************************** // //! Schedules a request for an IN transaction on an endpoint in host mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! //! This function will schedule a request for an IN transaction. When the USB //! device being communicated with responds the data, the data can be retrieved //! by calling USBEndpointDataGet() or via a DMA transfer. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostRequestIN(unsigned long ulBase, unsigned long ulEndpoint) { unsigned long ulRegister; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // Endpoint zero uses a different offset than the other endpoints. // if(ulEndpoint == USB_EP_0) { ulRegister = USB_O_CSRL0; } else { ulRegister = USB_O_RXCSRL1 + EP_OFFSET(ulEndpoint); } // // Set the request for an IN transaction. // HWREGB(ulBase + ulRegister) = USB_RXCSRL1_REQPKT; } //***************************************************************************** // //! Issues a request for a status IN transaction on endpoint zero. //! //! \param ulBase specifies the USB module base address. //! //! This function is used to cause a request for an status IN transaction from //! a device on endpoint zero. This function can only be used with endpoint //! zero as that is the only control endpoint that supports this ability. This //! is used to complete the last phase of a control transaction to a device and //! an interrupt will be signaled when the status packet has been received. //! //! \return None. // //***************************************************************************** void USBHostRequestStatus(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Set the request for a status IN transaction. // HWREGB(ulBase + USB_O_CSRL0) = USB_CSRL0_REQPKT | USB_CSRL0_STATUS; } //***************************************************************************** // //! Sets the functional address for the device that is connected to an //! endpoint in host mode. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulAddr is the functional address for the controller to use for this //! endpoint. //! \param ulFlags determines if this is an IN or an OUT endpoint. //! //! This function will set the functional address for a device that is using //! this endpoint for communication. This \e ulAddr parameter is the address //! of the target device that this endpoint will be used to communicate with. //! The \e ulFlags parameter indicates if the IN or OUT endpoint should be set. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostAddrSet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulAddr, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the transmit or receive address should be set. // if(ulFlags & USB_EP_HOST_OUT) { // // Set the transmit address. // HWREGB(ulBase + USB_O_TXFUNCADDR0 + (ulEndpoint >> 1)) = ulAddr; } else { // // Set the receive address. // HWREGB(ulBase + USB_O_TXFUNCADDR0 + 4 + (ulEndpoint >> 1)) = ulAddr; } } //***************************************************************************** // //! Gets the current functional device address for an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags determines if this is an IN or an OUT endpoint. //! //! This function returns the current functional address that an endpoint is //! using to communicate with a device. The \e ulFlags parameter determines if //! the IN or OUT endpoint's device address is returned. //! //! \note This function should only be called in host mode. //! //! \return Returns the current function address being used by an endpoint. // //***************************************************************************** unsigned long USBHostAddrGet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the transmit or receive address should be returned. // if(ulFlags & USB_EP_HOST_OUT) { // // Return this endpoint's transmit address. // return(HWREGB(ulBase + USB_O_TXFUNCADDR0 + (ulEndpoint >> 1))); } else { // // Return this endpoint's receive address. // return(HWREGB(ulBase + USB_O_TXFUNCADDR0 + 4 + (ulEndpoint >> 1))); } } //***************************************************************************** // //! Set the hub address for the device that is connected to an endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulAddr is the hub address for the device using this endpoint. //! \param ulFlags determines if this is an IN or an OUT endpoint. //! //! This function will set the hub address for a device that is using this //! endpoint for communication. The \e ulFlags parameter determines if the //! device address for the IN or the OUT endpoint is set by this call. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostHubAddrSet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulAddr, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the hub transmit or receive address is being set. // if(ulFlags & USB_EP_HOST_OUT) { // // Set the hub transmit address for this endpoint. // HWREGB(ulBase + USB_O_TXHUBADDR0 + (ulEndpoint >> 1)) = ulAddr; } else { // // Set the hub receive address for this endpoint. // HWREGB(ulBase + USB_O_TXHUBADDR0 + 4 + (ulEndpoint >> 1)) = ulAddr; } } //***************************************************************************** // //! Get the current device hub address for this endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint is the endpoint to access. //! \param ulFlags determines if this is an IN or an OUT endpoint. //! //! This function will return the current hub address that an endpoint is using //! to communicate with a device. The \e ulFlags parameter determines if the //! device address for the IN or OUT endpoint is returned. //! //! \note This function should only be called in host mode. //! //! \return This function returns the current hub address being used by an //! endpoint. // //***************************************************************************** unsigned long USBHostHubAddrGet(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_0) || (ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); // // See if the hub transmit or receive address should be returned. // if(ulFlags & USB_EP_HOST_OUT) { // // Return the hub transmit address for this endpoint. // return(HWREGB(ulBase + USB_O_TXHUBADDR0 + (ulEndpoint >> 1))); } else { // // Return the hub receive address for this endpoint. // return(HWREGB(ulBase + USB_O_TXHUBADDR0 + 4 + (ulEndpoint >> 1))); } } //***************************************************************************** // //! Sets the configuration for USB power fault. //! //! \param ulBase specifies the USB module base address. //! \param ulFlags specifies the configuration of the power fault. //! //! This function controls how the USB controller uses its external power //! control pins(USBnPFTL and USBnEPEN). The flags specify the power //! fault level sensitivity, the power fault action, and the power enable level //! and source. //! //! One of the following can be selected as the power fault level //! sensitivity: //! //! - \b USB_HOST_PWRFLT_LOW - An external power fault is indicated by the pin //! being driven low. //! - \b USB_HOST_PWRFLT_HIGH - An external power fault is indicated by the pin //! being driven high. //! //! One of the following can be selected as the power fault action: //! //! - \b USB_HOST_PWRFLT_EP_NONE - No automatic action when power fault //! detected. //! - \b USB_HOST_PWRFLT_EP_TRI - Automatically Tri-state the USBnEPEN pin on a //! power fault. //! - \b USB_HOST_PWRFLT_EP_LOW - Automatically drive USBnEPEN pin low on a //! power fault. //! - \b USB_HOST_PWRFLT_EP_HIGH - Automatically drive USBnEPEN pin high on a //! power fault. //! //! One of the following can be selected as the power enable level and source: //! //! - \b USB_HOST_PWREN_MAN_LOW - USBEPEN is driven low by the USB controller //! when USBHostPwrEnable() is called. //! - \b USB_HOST_PWREN_MAN_HIGH - USBEPEN is driven high by the USB controller //! when USBHostPwrEnable() is called. //! - \b USB_HOST_PWREN_AUTOLOW - USBEPEN is driven low by the USB controller //! automatically if USBOTGSessionRequest() has //! enabled a session. //! - \b USB_HOST_PWREN_AUTOHIGH - USBEPEN is driven high by the USB controller //! automatically if USBOTGSessionRequest() has //! enabled a session. //! //! On devices that support the VBUS glitch filter, the //! \b USB_HOST_PWREN_FILTER can be added to ignore small short drops in VBUS //! level caused by high power consumption. This is mainly used to avoid //! causing VBUS errors caused by devices with high in-rush current. //! //! \note The following values have been deprecated and should no longer be //! used. //! - \b USB_HOST_PWREN_LOW - Automatically drive USBnEPEN low when power is //! enabled. //! - \b USB_HOST_PWREN_HIGH - Automatically drive USBnEPEN high when power is //! enabled. //! - \b USB_HOST_PWREN_VBLOW - Automatically drive USBnEPEN low when power is //! enabled. //! - \b USB_HOST_PWREN_VBHIGH - Automatically drive USBnEPEN high when power is //! enabled. //! //! \note This function should only be called on microcontrollers that support //! host mode or OTG operation. //! //! \return None. // //***************************************************************************** void USBHostPwrConfig(unsigned long ulBase, unsigned long ulFlags) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulFlags & ~(USB_EPC_PFLTACT_M | USB_EPC_PFLTAEN | USB_EPC_PFLTSEN_HIGH | USB_EPC_EPEN_M)) == 0); // // If requested, enable VBUS droop detection on parts that support this // feature. // HWREG(ulBase + USB_O_VDC) = ulFlags >> 16; // // Set the power fault configuration as specified. This will not change // whether fault detection is enabled or not. // HWREGH(ulBase + USB_O_EPC) = (ulFlags | (HWREGH(ulBase + USB_O_EPC) & ~(USB_EPC_PFLTACT_M | USB_EPC_PFLTAEN | USB_EPC_PFLTSEN_HIGH | USB_EPC_EPEN_M))); } //***************************************************************************** // //! Enables power fault detection. //! //! \param ulBase specifies the USB module base address. //! //! This function enables power fault detection in the USB controller. If the //! USBPFLT pin is not in use this function should not be used. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostPwrFaultEnable(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Enable power fault input. // HWREGH(ulBase + USB_O_EPC) |= USB_EPC_PFLTEN; } //***************************************************************************** // //! Disables power fault detection. //! //! \param ulBase specifies the USB module base address. //! //! This function disables power fault detection in the USB controller. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostPwrFaultDisable(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Enable power fault input. // HWREGH(ulBase + USB_O_EPC) &= ~USB_EPC_PFLTEN; } //***************************************************************************** // //! Enables the external power pin. //! //! \param ulBase specifies the USB module base address. //! //! This function enables the USBEPEN signal to enable an external power supply //! in host mode operation. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostPwrEnable(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Enable the external power supply enable signal. // HWREGH(ulBase + USB_O_EPC) |= USB_EPC_EPENDE; } //***************************************************************************** // //! Disables the external power pin. //! //! \param ulBase specifies the USB module base address. //! //! This function disables the USBEPEN signal to disable an external power //! supply in host mode operation. //! //! \note This function should only be called in host mode. //! //! \return None. // //***************************************************************************** void USBHostPwrDisable(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Disable the external power supply enable signal. // HWREGH(ulBase + USB_O_EPC) &= ~USB_EPC_EPENDE; } //***************************************************************************** // //! Get the current frame number. //! //! \param ulBase specifies the USB module base address. //! //! This function returns the last frame number received. //! //! \return The last frame number received. // //***************************************************************************** unsigned long USBFrameNumberGet(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Return the most recent frame number. // return(HWREGH(ulBase + USB_O_FRAME)); } //***************************************************************************** // //! Starts or ends a session. //! //! \param ulBase specifies the USB module base address. //! \param bStart specifies if this call starts or ends a session. //! //! This function is used in OTG mode to start a session request or end a //! session. If the \e bStart parameter is set to \b true, then this function //! start a session and if it is \b false it will end a session. //! //! \return None. // //***************************************************************************** void USBOTGSessionRequest(unsigned long ulBase, tBoolean bStart) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Start or end the session as directed. // if(bStart) { HWREGB(ulBase + USB_O_DEVCTL) |= USB_DEVCTL_SESSION; } else { HWREGB(ulBase + USB_O_DEVCTL) &= ~USB_DEVCTL_SESSION; } } //***************************************************************************** // //! Returns the absolute FIFO address for a given endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint specifies which endpoint's FIFO address to return. //! //! This function returns the actual physical address of the FIFO. This is //! needed when the USB is going to be used with the uDMA controller and the //! source or destination address needs to be set to the physical FIFO address //! for a given endpoint. //! //! \return None. // //***************************************************************************** unsigned long USBFIFOAddrGet(unsigned long ulBase, unsigned long ulEndpoint) { // // Return the FIFO address for this endpoint. // return(ulBase + USB_O_FIFO0 + (ulEndpoint >> 2)); } //***************************************************************************** // //! Returns the current operating mode of the controller. //! //! \param ulBase specifies the USB module base address. //! //! This function returns the current operating mode on USB controllers with //! OTG or Dual mode functionality. //! //! For OTG controllers: //! //! The function will return on of the following values on OTG controllers: //! \b USB_OTG_MODE_ASIDE_HOST, \b USB_OTG_MODE_ASIDE_DEV, //! \b USB_OTG_MODE_BSIDE_HOST, \b USB_OTG_MODE_BSIDE_DEV, //! \b USB_OTG_MODE_NONE. //! //! \b USB_OTG_MODE_ASIDE_HOST indicates that the controller is in host mode //! on the A-side of the cable. //! //! \b USB_OTG_MODE_ASIDE_DEV indicates that the controller is in device mode //! on the A-side of the cable. //! //! \b USB_OTG_MODE_BSIDE_HOST indicates that the controller is in host mode //! on the B-side of the cable. //! //! \b USB_OTG_MODE_BSIDE_DEV indicates that the controller is in device mode //! on the B-side of the cable. If and OTG session request is started with no //! cable in place this is the default mode for the controller. //! //! \b USB_OTG_MODE_NONE indicates that the controller is not attempting to //! determine its role in the system. //! //! For Dual Mode controllers: //! //! The function will return on of the following values: //! \b USB_DUAL_MODE_HOST, \b USB_DUAL_MODE_DEVICE, or //! \b USB_DUAL_MODE_NONE. //! //! \b USB_DUAL_MODE_HOST indicates that the controller is acting as a host. //! //! \b USB_DUAL_MODE_DEVICE indicates that the controller acting as a device. //! //! \b USB_DUAL_MODE_NONE indicates that the controller is not active as //! either a host or device. //! //! \return Returns \b USB_OTG_MODE_ASIDE_HOST, \b USB_OTG_MODE_ASIDE_DEV, //! \b USB_OTG_MODE_BSIDE_HOST, \b USB_OTG_MODE_BSIDE_DEV, //! \b USB_OTG_MODE_NONE, \b USB_DUAL_MODE_HOST, \b USB_DUAL_MODE_DEVICE, or //! \b USB_DUAL_MODE_NONE. // //***************************************************************************** unsigned long USBModeGet(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Checks the current mode in the USB_O_DEVCTL and returns the current // mode. // // USB_OTG_MODE_ASIDE_HOST: USB_DEVCTL_HOST | USB_DEVCTL_SESSION // USB_OTG_MODE_ASIDE_DEV: USB_DEVCTL_SESSION // USB_OTG_MODE_BSIDE_HOST: USB_DEVCTL_DEV | USB_DEVCTL_SESSION | // USB_DEVCTL_HOST // USB_OTG_MODE_BSIDE_DEV: USB_DEVCTL_DEV | USB_DEVCTL_SESSION // USB_OTG_MODE_NONE: USB_DEVCTL_DEV // return(HWREGB(ulBase + USB_O_DEVCTL) & (USB_DEVCTL_DEV | USB_DEVCTL_HOST | USB_DEVCTL_SESSION | USB_DEVCTL_VBUS_M)); } //***************************************************************************** // //! Sets the DMA channel to use for a given endpoint. //! //! \param ulBase specifies the USB module base address. //! \param ulEndpoint specifies which endpoint's FIFO address to return. //! \param ulChannel specifies which DMA channel to use for which endpoint. //! //! This function is used to configure which DMA channel to use with a given //! endpoint. Receive DMA channels can only be used with receive endpoints //! and transmit DMA channels can only be used with transmit endpoints. This //! allows the 3 receive and 3 transmit DMA channels to be mapped to any //! endpoint other than 0. The values that should be passed into the \e //! ulChannel value are the UDMA_CHANNEL_USBEP* values defined in udma.h. //! //! \note This function only has an effect on microcontrollers that have the //! ability to change the DMA channel for an endpoint. Calling this function //! on other devices will have no effect. //! //! \return None. //! //***************************************************************************** void USBEndpointDMAChannel(unsigned long ulBase, unsigned long ulEndpoint, unsigned long ulChannel) { unsigned long ulMask; // // Check the arguments. // ASSERT(ulBase == USB0_BASE); ASSERT((ulEndpoint == USB_EP_1) || (ulEndpoint == USB_EP_2) || (ulEndpoint == USB_EP_3) || (ulEndpoint == USB_EP_4) || (ulEndpoint == USB_EP_5) || (ulEndpoint == USB_EP_6) || (ulEndpoint == USB_EP_7) || (ulEndpoint == USB_EP_8) || (ulEndpoint == USB_EP_9) || (ulEndpoint == USB_EP_10) || (ulEndpoint == USB_EP_11) || (ulEndpoint == USB_EP_12) || (ulEndpoint == USB_EP_13) || (ulEndpoint == USB_EP_14) || (ulEndpoint == USB_EP_15)); ASSERT(ulChannel <= UDMA_CHANNEL_USBEP3TX); // // The input select mask needs to be shifted into the correct position // based on the channel. // ulMask = 0xf << (ulChannel * 4); // // Clear out the current selection for the channel. // ulMask = HWREG(ulBase + USB_O_DMASEL) & (~ulMask); // // The input select is now shifted into the correct position based on the // channel. // ulMask |= (USB_EP_TO_INDEX(ulEndpoint)) << (ulChannel * 4); // // Write the value out to the register. // HWREG(ulBase + USB_O_DMASEL) = ulMask; } //***************************************************************************** // //! Change the mode of the USB controller to host. //! //! \param ulBase specifies the USB module base address. //! //! This function changes the mode of the USB controller to host mode. This //! is only valid on microcontrollers that have the host and device //! capabilities and not the OTG capabilities. //! //! \return None. // //***************************************************************************** void USBHostMode(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Force mode in OTG parts that support forcing USB controller mode. // This bit is not writable in USB controllers that do not support // forcing the mode. Not setting the USB_GPCS_DEVMOD bit makes this a // force of host mode. // HWREGB(ulBase + USB_O_GPCS) = USB_GPCS_DEVMODOTG; } //***************************************************************************** // //! Change the mode of the USB controller to device. //! //! \param ulBase specifies the USB module base address. //! //! This function changes the mode of the USB controller to device mode. This //! is only valid on microcontrollers that have the host and device //! capabilities and not the OTG capabilities. //! //! \return None. // //***************************************************************************** void USBDevMode(unsigned long ulBase) { // // Check the arguments. // ASSERT(ulBase == USB0_BASE); // // Set the USB controller mode to device. // HWREGB(ulBase + USB_O_GPCS) = USB_GPCS_DEVMODOTG | USB_GPCS_DEVMOD; } //***************************************************************************** // // Close the Doxygen group. //! @} // //*****************************************************************************