/****************************************************************************** * @file uart.h * @version V3.00 * $Revision: 36 $ * $Date: 15/08/11 10:26a $ * @brief M451 series UART driver header file * * @note * Copyright (C) 2013~2015 Nuvoton Technology Corp. All rights reserved. *****************************************************************************/ #ifndef __UART_H__ #define __UART_H__ #ifdef __cplusplus extern "C" { #endif /** @addtogroup Standard_Driver Standard Driver @{ */ /** @addtogroup UART_Driver UART Driver @{ */ /** @addtogroup UART_EXPORTED_CONSTANTS UART Exported Constants @{ */ /*---------------------------------------------------------------------------------------------------------*/ /* UART FIFO size constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART0_FIFO_SIZE 16 /*!< UART0 supports separated receive/transmit 16/16 bytes entry FIFO */ #define UART1_FIFO_SIZE 16 /*!< UART1 supports separated receive/transmit 16/16 bytes entry FIFO */ #define UART2_FIFO_SIZE 16 /*!< UART2 supports separated receive/transmit 16/16 bytes entry FIFO */ #define UART3_FIFO_SIZE 16 /*!< UART3 supports separated receive/transmit 16/16 bytes entry FIFO */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_FIFO constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_FIFO_RFITL_1BYTE (0x0 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 1 byte */ #define UART_FIFO_RFITL_4BYTES (0x1 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 4 bytes */ #define UART_FIFO_RFITL_8BYTES (0x2 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 8 bytes */ #define UART_FIFO_RFITL_14BYTES (0x3 << UART_FIFO_RFITL_Pos) /*!< UART_FIFO setting to set RX FIFO Trigger Level to 14 bytes */ #define UART_FIFO_RTSTRGLV_1BYTE (0x0 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 1 byte */ #define UART_FIFO_RTSTRGLV_4BYTES (0x1 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 4 bytes */ #define UART_FIFO_RTSTRGLV_8BYTES (0x2 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 8 bytes */ #define UART_FIFO_RTSTRGLV_14BYTES (0x3 << UART_FIFO_RTSTRGLV_Pos) /*!< UART_FIFO setting to set RTS Trigger Level to 14 bytes */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_LINE constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_WORD_LEN_5 (0) /*!< UART_LINE setting to set UART word length to 5 bits */ #define UART_WORD_LEN_6 (1) /*!< UART_LINE setting to set UART word length to 6 bits */ #define UART_WORD_LEN_7 (2) /*!< UART_LINE setting to set UART word length to 7 bits */ #define UART_WORD_LEN_8 (3) /*!< UART_LINE setting to set UART word length to 8 bits */ #define UART_PARITY_NONE (0x0 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to set UART as no parity */ #define UART_PARITY_ODD (0x1 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to set UART as odd parity */ #define UART_PARITY_EVEN (0x3 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to set UART as even parity */ #define UART_PARITY_MARK (0x5 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to keep parity bit as '1' */ #define UART_PARITY_SPACE (0x7 << UART_LINE_PBE_Pos) /*!< UART_LINE setting to keep parity bit as '0' */ #define UART_STOP_BIT_1 (0x0 << UART_LINE_NSB_Pos) /*!< UART_LINE setting for one stop bit */ #define UART_STOP_BIT_1_5 (0x1 << UART_LINE_NSB_Pos) /*!< UART_LINE setting for 1.5 stop bit when 5-bit word length */ #define UART_STOP_BIT_2 (0x1 << UART_LINE_NSB_Pos) /*!< UART_LINE setting for two stop bit when 6, 7, 8-bit word length */ /*---------------------------------------------------------------------------------------------------------*/ /* UART RTS ACTIVE LEVEL constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_RTS_IS_LOW_LEV_ACTIVE (0x1 << UART_MODEM_RTSACTLV_Pos) /*!< Set RTS is Low Level Active */ #define UART_RTS_IS_HIGH_LEV_ACTIVE (0x0 << UART_MODEM_RTSACTLV_Pos) /*!< Set RTS is High Level Active */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_IRDA constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_IRDA_TXEN (0x1 << UART_IRDA_TXEN_Pos) /*!< Set IrDA function Tx mode */ #define UART_IRDA_RXEN (0x0 << UART_IRDA_TXEN_Pos) /*!< Set IrDA function Rx mode */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_FUNCSEL constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_FUNCSEL_UART (0x0 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set UART Function (Default) */ #define UART_FUNCSEL_LIN (0x1 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set LIN Function */ #define UART_FUNCSEL_IrDA (0x2 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set IrDA Function */ #define UART_FUNCSEL_RS485 (0x3 << UART_FUNCSEL_FUNCSEL_Pos) /*!< UART_FUNCSEL setting to set RS485 Function */ /*---------------------------------------------------------------------------------------------------------*/ /* UART_LINCTL constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_LINCTL_BRKFL(x) (((x)-1) << UART_LINCTL_BRKFL_Pos) /*!< UART_LINCTL setting to set LIN Break Field Length, x = 10 ~ 15, default value is 12 */ #define UART_LINCTL_BSL(x) (((x)-1) << UART_LINCTL_BSL_Pos) /*!< UART_LINCTL setting to set LIN Break/Sync Delimiter Length, x = 1 ~ 4 */ #define UART_LINCTL_HSEL_BREAK (0x0UL << UART_LINCTL_HSEL_Pos) /*!< UART_LINCTL setting to set LIN Header Select to break field */ #define UART_LINCTL_HSEL_BREAK_SYNC (0x1UL << UART_LINCTL_HSEL_Pos) /*!< UART_LINCTL setting to set LIN Header Select to break field and sync field */ #define UART_LINCTL_HSEL_BREAK_SYNC_ID (0x2UL << UART_LINCTL_HSEL_Pos) /*!< UART_LINCTL setting to set LIN Header Select to break field, sync field and ID field*/ #define UART_LINCTL_PID(x) ((x) << UART_LINCTL_PID_Pos) /*!< UART_LINCTL setting to set LIN PID value */ /*---------------------------------------------------------------------------------------------------------*/ /* UART BAUDRATE MODE constants definitions */ /*---------------------------------------------------------------------------------------------------------*/ #define UART_BAUD_MODE0 (0) /*!< Set UART Baudrate Mode is Mode0 */ #define UART_BAUD_MODE2 (UART_BAUD_BAUDM1_Msk | UART_BAUD_BAUDM0_Msk) /*!< Set UART Baudrate Mode is Mode2 */ /*@}*/ /* end of group UART_EXPORTED_CONSTANTS */ /** @addtogroup UART_EXPORTED_FUNCTIONS UART Exported Functions @{ */ /** * @brief Calculate UART baudrate mode0 divider * * @param[in] u32SrcFreq UART clock frequency * @param[in] u32BaudRate Baudrate of UART module * * @return UART baudrate mode0 divider * * @details This macro calculate UART baudrate mode0 divider. */ #define UART_BAUD_MODE0_DIVIDER(u32SrcFreq, u32BaudRate) ((((u32SrcFreq) + ((u32BaudRate)*8)) / (u32BaudRate) >> 4)-2) /** * @brief Calculate UART baudrate mode2 divider * * @param[in] u32SrcFreq UART clock frequency * @param[in] u32BaudRate Baudrate of UART module * * @return UART baudrate mode2 divider * * @details This macro calculate UART baudrate mode2 divider. */ #define UART_BAUD_MODE2_DIVIDER(u32SrcFreq, u32BaudRate) ((((u32SrcFreq) + ((u32BaudRate)/2)) / (u32BaudRate))-2) /** * @brief Write UART data * * @param[in] uart The pointer of the specified UART module * @param[in] u8Data Data byte to transmit. * * @return None * * @details This macro write Data to Tx data register. */ #define UART_WRITE(uart, u8Data) ((uart)->DAT = (u8Data)) /** * @brief Read UART data * * @param[in] uart The pointer of the specified UART module * * @return The oldest data byte in RX FIFO. * * @details This macro read Rx data register. */ #define UART_READ(uart) ((uart)->DAT) /** * @brief Get Tx empty * * @param[in] uart The pointer of the specified UART module * * @retval 0 Tx FIFO is not empty * @retval >=1 Tx FIFO is empty * * @details This macro get Transmitter FIFO empty register value. */ #define UART_GET_TX_EMPTY(uart) ((uart)->FIFOSTS & UART_FIFOSTS_TXEMPTY_Msk) /** * @brief Get Rx empty * * @param[in] uart The pointer of the specified UART module * * @retval 0 Rx FIFO is not empty * @retval >=1 Rx FIFO is empty * * @details This macro get Receiver FIFO empty register value. */ #define UART_GET_RX_EMPTY(uart) ((uart)->FIFOSTS & UART_FIFOSTS_RXEMPTY_Msk) /** * @brief Check specified uart port transmission is over. * * @param[in] uart The pointer of the specified UART module * * @retval 0 Tx transmission is not over * @retval 1 Tx transmission is over * * @details This macro return Transmitter Empty Flag register bit value. * It indicates if specified uart port transmission is over nor not. */ #define UART_IS_TX_EMPTY(uart) (((uart)->FIFOSTS & UART_FIFOSTS_TXEMPTYF_Msk) >> UART_FIFOSTS_TXEMPTYF_Pos) /** * @brief Wait specified uart port transmission is over * * @param[in] uart The pointer of the specified UART module * * @return None * * @details This macro wait specified uart port transmission is over. */ #define UART_WAIT_TX_EMPTY(uart) while(!((((uart)->FIFOSTS) & UART_FIFOSTS_TXEMPTYF_Msk) >> UART_FIFOSTS_TXEMPTYF_Pos)) /** * @brief Check RX is ready or not * * @param[in] uart The pointer of the specified UART module * * @retval 0 The number of bytes in the RX FIFO is less than the RFITL * @retval 1 The number of bytes in the RX FIFO equals or larger than RFITL * * @details This macro check receive data available interrupt flag is set or not. */ #define UART_IS_RX_READY(uart) (((uart)->INTSTS & UART_INTSTS_RDAIF_Msk)>>UART_INTSTS_RDAIF_Pos) /** * @brief Check TX FIFO is full or not * * @param[in] uart The pointer of the specified UART module * * @retval 1 TX FIFO is full * @retval 0 TX FIFO is not full * * @details This macro check TX FIFO is full or not. */ #define UART_IS_TX_FULL(uart) (((uart)->FIFOSTS & UART_FIFOSTS_TXFULL_Msk)>>UART_FIFOSTS_TXFULL_Pos) /** * @brief Check RX FIFO is full or not * * @param[in] uart The pointer of the specified UART module * * @retval 1 RX FIFO is full * @retval 0 RX FIFO is not full * * @details This macro check RX FIFO is full or not. */ #define UART_IS_RX_FULL(uart) (((uart)->FIFOSTS & UART_FIFOSTS_RXFULL_Msk)>>UART_FIFOSTS_RXFULL_Pos) /** * @brief Get Tx full register value * * @param[in] uart The pointer of the specified UART module * * @retval 0 Tx FIFO is not full. * @retval >=1 Tx FIFO is full. * * @details This macro get Tx full register value. */ #define UART_GET_TX_FULL(uart) ((uart)->FIFOSTS & UART_FIFOSTS_TXFULL_Msk) /** * @brief Get Rx full register value * * @param[in] uart The pointer of the specified UART module * * @retval 0 Rx FIFO is not full. * @retval >=1 Rx FIFO is full. * * @details This macro get Rx full register value. */ #define UART_GET_RX_FULL(uart) ((uart)->FIFOSTS & UART_FIFOSTS_RXFULL_Msk) /** * @brief Enable specified UART interrupt * * @param[in] uart The pointer of the specified UART module * @param[in] u32eIntSel Interrupt type select * - \ref UART_INTEN_ABRIEN_Msk : Auto baud rate interrupt * - \ref UART_INTEN_WKCTSIEN_Msk : CTS wakeup interrupt * - \ref UART_INTEN_WKDATIEN_Msk : Data wakeup interrupt * - \ref UART_INTEN_LINIEN_Msk : Lin bus interrupt * - \ref UART_INTEN_BUFERRIEN_Msk : Buffer Error interrupt * - \ref UART_INTEN_RXTOIEN_Msk : Rx time-out interrupt * - \ref UART_INTEN_MODEMIEN_Msk : Modem interrupt * - \ref UART_INTEN_RLSIEN_Msk : Rx Line status interrupt * - \ref UART_INTEN_THREIEN_Msk : Tx empty interrupt * - \ref UART_INTEN_RDAIEN_Msk : Rx ready interrupt * * @return None * * @details This macro enable specified UART interrupt. */ #define UART_ENABLE_INT(uart, u32eIntSel) ((uart)->INTEN |= (u32eIntSel)) /** * @brief Disable specified UART interrupt * * @param[in] uart The pointer of the specified UART module * @param[in] u32eIntSel Interrupt type select * - \ref UART_INTEN_ABRIEN_Msk : Auto baud rate interrupt * - \ref UART_INTEN_WKCTSIEN_Msk : CTS wakeup interrupt * - \ref UART_INTEN_WKDATIEN_Msk : Data wakeup interrupt * - \ref UART_INTEN_LINIEN_Msk : Lin bus interrupt * - \ref UART_INTEN_BUFERRIEN_Msk : Buffer Error interrupt * - \ref UART_INTEN_RXTOIEN_Msk : Rx time-out interrupt * - \ref UART_INTEN_MODEMIEN_Msk : Modem status interrupt * - \ref UART_INTEN_RLSIEN_Msk : Receive Line status interrupt * - \ref UART_INTEN_THREIEN_Msk : Tx empty interrupt * - \ref UART_INTEN_RDAIEN_Msk : Rx ready interrupt * * @return None * * @details This macro enable specified UART interrupt. */ #define UART_DISABLE_INT(uart, u32eIntSel) ((uart)->INTEN &= ~ (u32eIntSel)) /** * @brief Get specified interrupt flag/status * * @param[in] uart The pointer of the specified UART module * @param[in] u32eIntTypeFlag Interrupt Type Flag, should be * - \ref UART_INTSTS_HWBUFEINT_Msk : In DMA Mode, Buffer Error Interrupt Indicator * - \ref UART_INTSTS_HWTOINT_Msk : In DMA Mode, Time-out Interrupt Indicator * - \ref UART_INTSTS_HWMODINT_Msk : In DMA Mode, MODEM Status Interrupt Indicator * - \ref UART_INTSTS_HWRLSINT_Msk : In DMA Mode, Receive Line Status Interrupt Indicator * - \ref UART_INTSTS_HWBUFEIF_Msk : In DMA Mode, Buffer Error Interrupt Flag * - \ref UART_INTSTS_HWTOIF_Msk : In DMA Mode, Time-out Interrupt Flag * - \ref UART_INTSTS_HWMODIF_Msk : In DMA Mode, MODEM Interrupt Flag * - \ref UART_INTSTS_HWRLSIF_Msk : In DMA Mode, Receive Line Status Flag * - \ref UART_INTSTS_LININT_Msk : LIN Bus Interrupt Indicator * - \ref UART_INTSTS_BUFERRINT_Msk : Buffer Error Interrupt Indicator * - \ref UART_INTSTS_RXTOINT_Msk : Time-out Interrupt Indicator * - \ref UART_INTSTS_MODEMINT_Msk : Modem Status Interrupt Indicator * - \ref UART_INTSTS_RLSINT_Msk : Receive Line Status Interrupt Indicator * - \ref UART_INTSTS_THREINT_Msk : Transmit Holding Register Empty Interrupt Indicator * - \ref UART_INTSTS_RDAINT_Msk : Receive Data Available Interrupt Indicator * - \ref UART_INTSTS_LINIF_Msk : LIN Bus Flag * - \ref UART_INTSTS_BUFERRIF_Msk : Buffer Error Interrupt Flag * - \ref UART_INTSTS_RXTOIF_Msk : Rx Time-out Interrupt Flag * - \ref UART_INTSTS_MODEMIF_Msk : Modem Interrupt Flag * - \ref UART_INTSTS_RLSIF_Msk : Receive Line Status Interrupt Flag * - \ref UART_INTSTS_THREIF_Msk : Tx Empty Interrupt Flag * - \ref UART_INTSTS_RDAIF_Msk : Rx Ready Interrupt Flag * * @retval 0 The specified interrupt is not happened. * 1 The specified interrupt is happened. * * @details This macro get specified interrupt flag or interrupt indicator status. */ #define UART_GET_INT_FLAG(uart,u32eIntTypeFlag) (((uart)->INTSTS & (u32eIntTypeFlag))?1:0) /** * @brief Set RTS pin to low * * @param[in] uart The pointer of the specified UART module * * @return None * * @details This macro set RTS pin to low. */ __STATIC_INLINE void UART_CLEAR_RTS(UART_T* uart) { uart->MODEM |= UART_MODEM_RTSACTLV_Msk; uart->MODEM &= ~UART_MODEM_RTS_Msk; } /** * @brief Set RTS pin to high * * @param[in] uart The pointer of the specified UART module * * @return None * * @details This macro set RTS pin to high. */ __STATIC_INLINE void UART_SET_RTS(UART_T* uart) { uart->MODEM |= UART_MODEM_RTSACTLV_Msk | UART_MODEM_RTS_Msk; } /** * @brief Clear RS-485 Address Byte Detection Flag * * @param[in] uart The pointer of the specified UART module * * @return None * * @details This macro clear RS-485 address byte detection flag. */ #define UART_RS485_CLEAR_ADDR_FLAG(uart) ((uart)->FIFOSTS = UART_FIFOSTS_ADDRDETF_Msk) /** * @brief Get RS-485 Address Byte Detection Flag * * @param[in] uart The pointer of the specified UART module * * @retval 0 Receiver detects a data that is not an address bit. * @retval 1 Receiver detects a data that is an address bit. * * @details This macro get RS-485 address byte detection flag. */ #define UART_RS485_GET_ADDR_FLAG(uart) (((uart)->FIFOSTS & UART_FIFOSTS_ADDRDETF_Msk) >> UART_FIFOSTS_ADDRDETF_Pos) void UART_ClearIntFlag(UART_T* uart , uint32_t u32InterruptFlag); void UART_Close(UART_T* uart); void UART_DisableFlowCtrl(UART_T* uart); void UART_DisableInt(UART_T* uart, uint32_t u32InterruptFlag); void UART_EnableFlowCtrl(UART_T* uart); void UART_EnableInt(UART_T* uart, uint32_t u32InterruptFlag); void UART_Open(UART_T* uart, uint32_t u32baudrate); uint32_t UART_Read(UART_T* uart, uint8_t *pu8RxBuf, uint32_t u32ReadBytes); void UART_SetLine_Config(UART_T* uart, uint32_t u32baudrate, uint32_t u32data_width, uint32_t u32parity, uint32_t u32stop_bits); void UART_SetTimeoutCnt(UART_T* uart, uint32_t u32TOC); void UART_SelectIrDAMode(UART_T* uart, uint32_t u32Buadrate, uint32_t u32Direction); void UART_SelectRS485Mode(UART_T* uart, uint32_t u32Mode, uint32_t u32Addr); void UART_SelectLINMode(UART_T* uart, uint32_t u32Mode, uint32_t u32BreakLength); uint32_t UART_Write(UART_T* uart, uint8_t *pu8TxBuf, uint32_t u32WriteBytes); /*@}*/ /* end of group UART_EXPORTED_FUNCTIONS */ /*@}*/ /* end of group UART_Driver */ /*@}*/ /* end of group Standard_Driver */ #ifdef __cplusplus } #endif #endif //__UART_H__ /*** (C) COPYRIGHT 2013~2015 Nuvoton Technology Corp. ***/