[bsp][stm32]Add stm32l431-tencentos-tiny-EVB_MX+ remaining drivers

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/.config

@@ -491,6 +491,9 @@ CONFIG_RT_LIBC_TZ_DEFAULT_SEC=0
 # CMSIS: ARM Cortex-M Microcontroller Software Interface Standard
 #
 # CONFIG_PKG_USING_CMSIS_5 is not set
+# CONFIG_PKG_USING_CMSIS_CORE is not set
+# CONFIG_PKG_USING_CMSIS_DSP is not set
+# CONFIG_PKG_USING_CMSIS_NN is not set
 # CONFIG_PKG_USING_CMSIS_RTOS1 is not set
 # CONFIG_PKG_USING_CMSIS_RTOS2 is not set
 
@@ -562,6 +565,7 @@ CONFIG_RT_LIBC_TZ_DEFAULT_SEC=0
 #
 # STM32 HAL & SDK Drivers
 #
+# CONFIG_PKG_USING_STM32L4XX_HAL_DRIVER is not set
 # CONFIG_PKG_USING_STM32WB55_SDK is not set
 # CONFIG_PKG_USING_STM32_SDIO is not set
 # CONFIG_PKG_USING_BLUETRUM_SDK is not set
@@ -729,6 +733,7 @@ CONFIG_RT_LIBC_TZ_DEFAULT_SEC=0
 # CONFIG_PKG_USING_X9555 is not set
 # CONFIG_PKG_USING_SYSTEM_RUN_LED is not set
 # CONFIG_PKG_USING_BT_MX01 is not set
+# CONFIG_PKG_USING_RGPOWER is not set
 # CONFIG_PKG_USING_SPI_TOOLS is not set
 
 #
@@ -753,7 +758,6 @@ CONFIG_RT_LIBC_TZ_DEFAULT_SEC=0
 # CONFIG_PKG_USING_UKAL is not set
 # CONFIG_PKG_USING_DIGITALCTRL is not set
 # CONFIG_PKG_USING_KISSFFT is not set
-# CONFIG_PKG_USING_CMSIS_DSP is not set
 
 #
 # miscellaneous packages
@@ -1060,7 +1064,17 @@ CONFIG_SOC_STM32L431RC=y
 #
 CONFIG_BSP_USING_GPIO=y
 CONFIG_BSP_USING_UART=y
+# CONFIG_BSP_USING_UART1 is not set
 CONFIG_BSP_USING_UART2=y
+# CONFIG_BSP_USING_UART3 is not set
+# CONFIG_BSP_USING_LPUART1 is not set
+# CONFIG_BSP_USING_ADC is not set
+# CONFIG_BSP_USING_ONCHIP_RTC is not set
+# CONFIG_BSP_USING_DAC is not set
+# CONFIG_BSP_USING_SPI is not set
+# CONFIG_BSP_USING_QSPI_FLASH is not set
+# CONFIG_BSP_USING_SDCARD is not set
+# CONFIG_BSP_USING_I2C1 is not set
 # CONFIG_BSP_USING_CRC is not set
 # CONFIG_BSP_USING_RNG is not set
 # CONFIG_BSP_USING_UDID is not set

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/README.md

@@ -43,18 +43,17 @@ tiny 提供精简的 RTOS 内核，内核组件可裁剪可配置，可快速移
 | **板载外设**       | **支持情况**  | **备注**                                |
 |:---------------|:---------:|:--------------------------------------|
 | USB 转串口        |    支持     | 默认Finsh串口输出端，连接至UART2                 |
-| SPI Flash      |   暂不支持    |                                       |
+| QSPI Flash      |   支持    |                                       |
-| 以太网            |   暂不支持    |                                       |
+| SD卡            |   支持    |                                       |
-| SD卡            |   暂不支持    |                                       |
-| CAN            |   暂不支持    |                                       |
 | **片上外设**       | **支持情况**  | **备注**                                |
 | GPIO           |    支持     | PA0, PA1... PK15 ---> PIN: 0, 1...176 |
 | UART           |    支持     | LPUART1/UART2/x                       |
-| SPI            |   暂不支持    | SPI1/x/x                              |
+| SPI            |   支持    | SPI1/3                              |
-| I2C            |   暂不支持    | 软件 I2C                                |
+| I2C            |   支持    | 软件 I2C                                |
-| SDIO           |   暂不支持    | 即将支持                                  |
+| SDIO           |   支持    |                                   |
-| RTC            |   暂不支持    | 即将支持                                  |
+| RTC            |   支持    |    LSE                               |
-| PWM            |   暂不支持    | 即将支持                                  |
+|ADC|支持|ADC1,(E53 LAN Interface)
+|DAC |支持|DAC1,(E53 LAN Interface)
 | **扩展模块**       | **支持情况**  | **备注**                                |
 | GPS模块          |   暂不支持    | 即将支持                                  |
 | BC35-G模块       |   暂不支持    | 即将支持                                  |
@@ -106,7 +105,7 @@ msh >
 
 ### 进阶使用
 
-此 BSP 默认只开启了 GPIO 和 串口1 的功能，如果需使用 SD 卡、Flash 等更多高级功能，需要利用 ENV 工具对BSP 进行配置，步骤如下：
+此 BSP 默认只开启了 GPIO 和 UART2 的功能，如果需使用 SD 卡、Flash 等更多高级功能，需要利用 ENV 工具对BSP 进行配置，步骤如下：
 
 1. 在 bsp 下打开 env 工具。
 

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/applications/main.c

@@ -12,6 +12,8 @@
 #include <rtdevice.h>
 #include <board.h>
 
+
+
 /* defined the LED0 pin: PC13 */
 #define LED0_PIN    GET_PIN(C, 13)
 

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/CubeMX_Config/Core/Inc/stm32l4xx_hal_conf.h

@@ -36,14 +36,14 @@ extern "C" {
   * @brief This is the list of modules to be used in the HAL driver
   */
 #define HAL_MODULE_ENABLED
-/*#define HAL_ADC_MODULE_ENABLED   */
+#define HAL_ADC_MODULE_ENABLED
 /*#define HAL_CRYP_MODULE_ENABLED   */
 /*#define HAL_CAN_MODULE_ENABLED   */
 /*#define HAL_COMP_MODULE_ENABLED   */
 /*#define HAL_I2C_MODULE_ENABLED   */
 /*#define HAL_CRC_MODULE_ENABLED   */
 /*#define HAL_CRYP_MODULE_ENABLED   */
-/*#define HAL_DAC_MODULE_ENABLED   */
+#define HAL_DAC_MODULE_ENABLED
 /*#define HAL_DCMI_MODULE_ENABLED   */
 /*#define HAL_DMA2D_MODULE_ENABLED   */
 /*#define HAL_DFSDM_MODULE_ENABLED   */
@@ -67,14 +67,14 @@ extern "C" {
 /*#define HAL_PCD_MODULE_ENABLED   */
 /*#define HAL_PKA_MODULE_ENABLED   */
 /*#define HAL_QSPI_MODULE_ENABLED   */
-/*#define HAL_QSPI_MODULE_ENABLED   */
+#define HAL_QSPI_MODULE_ENABLED
 /*#define HAL_RNG_MODULE_ENABLED   */
-/*#define HAL_RTC_MODULE_ENABLED   */
+#define HAL_RTC_MODULE_ENABLED
 /*#define HAL_SAI_MODULE_ENABLED   */
-/*#define HAL_SD_MODULE_ENABLED   */
+#define HAL_SD_MODULE_ENABLED
 /*#define HAL_SMBUS_MODULE_ENABLED   */
 /*#define HAL_SMARTCARD_MODULE_ENABLED   */
-/*#define HAL_SPI_MODULE_ENABLED   */
+#define HAL_SPI_MODULE_ENABLED
 /*#define HAL_SRAM_MODULE_ENABLED   */
 /*#define HAL_SWPMI_MODULE_ENABLED   */
 /*#define HAL_TIM_MODULE_ENABLED   */
@@ -255,21 +255,15 @@ extern "C" {
   */
 
 #ifdef HAL_RCC_MODULE_ENABLED
-
   #include "stm32l4xx_hal_rcc.h"
-
 #endif /* HAL_RCC_MODULE_ENABLED */
 
 #ifdef HAL_GPIO_MODULE_ENABLED
-
   #include "stm32l4xx_hal_gpio.h"
-
 #endif /* HAL_GPIO_MODULE_ENABLED */
 
 #ifdef HAL_DMA_MODULE_ENABLED
-
   #include "stm32l4xx_hal_dma.h"
-
 #endif /* HAL_DMA_MODULE_ENABLED */
 
 #ifdef HAL_DFSDM_MODULE_ENABLED
@@ -277,9 +271,7 @@ extern "C" {
 #endif /* HAL_DFSDM_MODULE_ENABLED */
 
 #ifdef HAL_CORTEX_MODULE_ENABLED
-
   #include "stm32l4xx_hal_cortex.h"
-
 #endif /* HAL_CORTEX_MODULE_ENABLED */
 
 #ifdef HAL_ADC_MODULE_ENABLED
@@ -323,9 +315,7 @@ extern "C" {
 #endif /* HAL_DSI_MODULE_ENABLED */
 
 #ifdef HAL_EXTI_MODULE_ENABLED
-
   #include "stm32l4xx_hal_exti.h"
-
 #endif /* HAL_EXTI_MODULE_ENABLED */
 
 #ifdef HAL_GFXMMU_MODULE_ENABLED
@@ -337,9 +327,7 @@ extern "C" {
 #endif /* HAL_FIREWALL_MODULE_ENABLED */
 
 #ifdef HAL_FLASH_MODULE_ENABLED
-
   #include "stm32l4xx_hal_flash.h"
-
 #endif /* HAL_FLASH_MODULE_ENABLED */
 
 #ifdef HAL_HASH_MODULE_ENABLED
@@ -407,9 +395,7 @@ extern "C" {
 #endif /* HAL_PSSI_MODULE_ENABLED */
 
 #ifdef HAL_PWR_MODULE_ENABLED
-
   #include "stm32l4xx_hal_pwr.h"
-
 #endif /* HAL_PWR_MODULE_ENABLED */
 
 #ifdef HAL_QSPI_MODULE_ENABLED
@@ -461,9 +447,7 @@ extern "C" {
 #endif /* HAL_TSC_MODULE_ENABLED */
 
 #ifdef HAL_UART_MODULE_ENABLED
-
   #include "stm32l4xx_hal_uart.h"
-
 #endif /* HAL_UART_MODULE_ENABLED */
 
 #ifdef HAL_USART_MODULE_ENABLED

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/CubeMX_Config/Core/Inc/stm32l4xx_it.h

@@ -47,21 +47,13 @@ extern "C" {
 
 /* Exported functions prototypes ---------------------------------------------*/
 void NMI_Handler(void);
-
 void HardFault_Handler(void);
-
 void MemManage_Handler(void);
-
 void BusFault_Handler(void);
-
 void UsageFault_Handler(void);
-
 void SVC_Handler(void);
-
 void DebugMon_Handler(void);
-
 void PendSV_Handler(void);
-
 void SysTick_Handler(void);
 /* USER CODE BEGIN EFP */
 

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/CubeMX_Config/Core/Src/stm32l4xx_hal_msp.c

@@ -20,7 +20,6 @@
 
 /* Includes ------------------------------------------------------------------*/
 #include "main.h"
-
 /* USER CODE BEGIN Includes */
 #include "drv_common.h"
 /* USER CODE END Includes */
@@ -61,7 +60,9 @@
 /**
   * Initializes the Global MSP.
   */
-void HAL_MspInit(void) {
+void HAL_MspInit(void)
+{
+
   /* USER CODE BEGIN MspInit 0 */
 
   /* USER CODE END MspInit 0 */
@@ -76,16 +77,216 @@ void HAL_MspInit(void) {
   /* USER CODE END MspInit 1 */
 }
 
+/**
+* @brief ADC MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hadc: ADC handle pointer
+* @retval None
+*/
+void HAL_ADC_MspInit(ADC_HandleTypeDef* hadc)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hadc->Instance==ADC1)
+  {
+  /* USER CODE BEGIN ADC1_MspInit 0 */
+
+  /* USER CODE END ADC1_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_ADC_CLK_ENABLE();
+
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    /**ADC1 GPIO Configuration
+    PC2     ------> ADC1_IN3
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_2;
+    GPIO_InitStruct.Mode = GPIO_MODE_ANALOG_ADC_CONTROL;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN ADC1_MspInit 1 */
+
+  /* USER CODE END ADC1_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief ADC MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hadc: ADC handle pointer
+* @retval None
+*/
+void HAL_ADC_MspDeInit(ADC_HandleTypeDef* hadc)
+{
+  if(hadc->Instance==ADC1)
+  {
+  /* USER CODE BEGIN ADC1_MspDeInit 0 */
+
+  /* USER CODE END ADC1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_ADC_CLK_DISABLE();
+
+    /**ADC1 GPIO Configuration
+    PC2     ------> ADC1_IN3
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_2);
+
+  /* USER CODE BEGIN ADC1_MspDeInit 1 */
+
+  /* USER CODE END ADC1_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief DAC MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hdac: DAC handle pointer
+* @retval None
+*/
+void HAL_DAC_MspInit(DAC_HandleTypeDef* hdac)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hdac->Instance==DAC1)
+  {
+  /* USER CODE BEGIN DAC1_MspInit 0 */
+
+  /* USER CODE END DAC1_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_DAC1_CLK_ENABLE();
+
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    /**DAC1 GPIO Configuration
+    PA4     ------> DAC1_OUT1
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_4;
+    GPIO_InitStruct.Mode = GPIO_MODE_ANALOG;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN DAC1_MspInit 1 */
+
+  /* USER CODE END DAC1_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief DAC MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hdac: DAC handle pointer
+* @retval None
+*/
+void HAL_DAC_MspDeInit(DAC_HandleTypeDef* hdac)
+{
+  if(hdac->Instance==DAC1)
+  {
+  /* USER CODE BEGIN DAC1_MspDeInit 0 */
+
+  /* USER CODE END DAC1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_DAC1_CLK_DISABLE();
+
+    /**DAC1 GPIO Configuration
+    PA4     ------> DAC1_OUT1
+    */
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_4);
+
+  /* USER CODE BEGIN DAC1_MspDeInit 1 */
+
+  /* USER CODE END DAC1_MspDeInit 1 */
+  }
+
+}
+
 /**
 * @brief UART MSP Initialization
 * This function configures the hardware resources used in this example
 * @param huart: UART handle pointer
 * @retval None
 */
-void HAL_UART_MspInit(UART_HandleTypeDef *huart) {
+void HAL_UART_MspInit(UART_HandleTypeDef* huart)
+{
   GPIO_InitTypeDef GPIO_InitStruct = {0};
   RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
-    if (huart->Instance == USART2) {
+  if(huart->Instance==LPUART1)
+  {
+  /* USER CODE BEGIN LPUART1_MspInit 0 */
+
+  /* USER CODE END LPUART1_MspInit 0 */
+
+  /** Initializes the peripherals clock
+  */
+    PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_LPUART1;
+    PeriphClkInit.Lpuart1ClockSelection = RCC_LPUART1CLKSOURCE_PCLK1;
+    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+    {
+      Error_Handler();
+    }
+
+    /* Peripheral clock enable */
+    __HAL_RCC_LPUART1_CLK_ENABLE();
+
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    /**LPUART1 GPIO Configuration
+    PC1     ------> LPUART1_TX
+    PB10     ------> LPUART1_RX
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_1;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF8_LPUART1;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_10;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF8_LPUART1;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN LPUART1_MspInit 1 */
+
+  /* USER CODE END LPUART1_MspInit 1 */
+  }
+  else if(huart->Instance==USART1)
+  {
+  /* USER CODE BEGIN USART1_MspInit 0 */
+
+  /* USER CODE END USART1_MspInit 0 */
+
+  /** Initializes the peripherals clock
+  */
+    PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART1;
+    PeriphClkInit.Usart1ClockSelection = RCC_USART1CLKSOURCE_PCLK2;
+    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+    {
+      Error_Handler();
+    }
+
+    /* Peripheral clock enable */
+    __HAL_RCC_USART1_CLK_ENABLE();
+
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    /**USART1 GPIO Configuration
+    PA9     ------> USART1_TX
+    PA10     ------> USART1_RX
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_9|GPIO_PIN_10;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF7_USART1;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN USART1_MspInit 1 */
+
+  /* USER CODE END USART1_MspInit 1 */
+  }
+  else if(huart->Instance==USART2)
+  {
   /* USER CODE BEGIN USART2_MspInit 0 */
 
   /* USER CODE END USART2_MspInit 0 */
@@ -94,7 +295,8 @@ void HAL_UART_MspInit(UART_HandleTypeDef *huart) {
   */
     PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART2;
     PeriphClkInit.Usart2ClockSelection = RCC_USART2CLKSOURCE_PCLK1;
-        if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) {
+    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+    {
       Error_Handler();
     }
 
@@ -104,19 +306,60 @@ void HAL_UART_MspInit(UART_HandleTypeDef *huart) {
     __HAL_RCC_GPIOA_CLK_ENABLE();
     /**USART2 GPIO Configuration
     PA2     ------> USART2_TX
-        PA3     ------> USART2_RX
+    PA15 (JTDI)     ------> USART2_RX
     */
-        GPIO_InitStruct.Pin = GPIO_PIN_2 | GPIO_PIN_3;
+    GPIO_InitStruct.Pin = GPIO_PIN_2;
     GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
     GPIO_InitStruct.Pull = GPIO_NOPULL;
     GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
     GPIO_InitStruct.Alternate = GPIO_AF7_USART2;
     HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
 
+    GPIO_InitStruct.Pin = GPIO_PIN_15;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF3_USART2;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
   /* USER CODE BEGIN USART2_MspInit 1 */
 
   /* USER CODE END USART2_MspInit 1 */
   }
+  else if(huart->Instance==USART3)
+  {
+  /* USER CODE BEGIN USART3_MspInit 0 */
+
+  /* USER CODE END USART3_MspInit 0 */
+
+  /** Initializes the peripherals clock
+  */
+    PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_USART3;
+    PeriphClkInit.Usart3ClockSelection = RCC_USART3CLKSOURCE_PCLK1;
+    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+    {
+      Error_Handler();
+    }
+
+    /* Peripheral clock enable */
+    __HAL_RCC_USART3_CLK_ENABLE();
+
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    /**USART3 GPIO Configuration
+    PC4     ------> USART3_TX
+    PC5     ------> USART3_RX
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_4|GPIO_PIN_5;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF7_USART3;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN USART3_MspInit 1 */
+
+  /* USER CODE END USART3_MspInit 1 */
+  }
 
 }
 
@@ -126,8 +369,48 @@ void HAL_UART_MspInit(UART_HandleTypeDef *huart) {
 * @param huart: UART handle pointer
 * @retval None
 */
-void HAL_UART_MspDeInit(UART_HandleTypeDef *huart) {
+void HAL_UART_MspDeInit(UART_HandleTypeDef* huart)
-    if (huart->Instance == USART2) {
+{
+  if(huart->Instance==LPUART1)
+  {
+  /* USER CODE BEGIN LPUART1_MspDeInit 0 */
+
+  /* USER CODE END LPUART1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_LPUART1_CLK_DISABLE();
+
+    /**LPUART1 GPIO Configuration
+    PC1     ------> LPUART1_TX
+    PB10     ------> LPUART1_RX
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_1);
+
+    HAL_GPIO_DeInit(GPIOB, GPIO_PIN_10);
+
+  /* USER CODE BEGIN LPUART1_MspDeInit 1 */
+
+  /* USER CODE END LPUART1_MspDeInit 1 */
+  }
+  else if(huart->Instance==USART1)
+  {
+  /* USER CODE BEGIN USART1_MspDeInit 0 */
+
+  /* USER CODE END USART1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_USART1_CLK_DISABLE();
+
+    /**USART1 GPIO Configuration
+    PA9     ------> USART1_TX
+    PA10     ------> USART1_RX
+    */
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_9|GPIO_PIN_10);
+
+  /* USER CODE BEGIN USART1_MspDeInit 1 */
+
+  /* USER CODE END USART1_MspDeInit 1 */
+  }
+  else if(huart->Instance==USART2)
+  {
   /* USER CODE BEGIN USART2_MspDeInit 0 */
 
   /* USER CODE END USART2_MspDeInit 0 */
@@ -136,14 +419,364 @@ void HAL_UART_MspDeInit(UART_HandleTypeDef *huart) {
 
     /**USART2 GPIO Configuration
     PA2     ------> USART2_TX
-        PA3     ------> USART2_RX
+    PA15 (JTDI)     ------> USART2_RX
     */
-        HAL_GPIO_DeInit(GPIOA, GPIO_PIN_2 | GPIO_PIN_3);
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_2|GPIO_PIN_15);
 
   /* USER CODE BEGIN USART2_MspDeInit 1 */
 
   /* USER CODE END USART2_MspDeInit 1 */
   }
+  else if(huart->Instance==USART3)
+  {
+  /* USER CODE BEGIN USART3_MspDeInit 0 */
+
+  /* USER CODE END USART3_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_USART3_CLK_DISABLE();
+
+    /**USART3 GPIO Configuration
+    PC4     ------> USART3_TX
+    PC5     ------> USART3_RX
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_4|GPIO_PIN_5);
+
+  /* USER CODE BEGIN USART3_MspDeInit 1 */
+
+  /* USER CODE END USART3_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief QSPI MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hqspi: QSPI handle pointer
+* @retval None
+*/
+void HAL_QSPI_MspInit(QSPI_HandleTypeDef* hqspi)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hqspi->Instance==QUADSPI)
+  {
+  /* USER CODE BEGIN QUADSPI_MspInit 0 */
+
+  /* USER CODE END QUADSPI_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_QSPI_CLK_ENABLE();
+
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    /**QUADSPI GPIO Configuration
+    PA3     ------> QUADSPI_CLK
+    PB0     ------> QUADSPI_BK1_IO1
+    PB1     ------> QUADSPI_BK1_IO0
+    PB11     ------> QUADSPI_BK1_NCS
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_3;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF10_QUADSPI;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_11;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF10_QUADSPI;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN QUADSPI_MspInit 1 */
+
+  /* USER CODE END QUADSPI_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief QSPI MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hqspi: QSPI handle pointer
+* @retval None
+*/
+void HAL_QSPI_MspDeInit(QSPI_HandleTypeDef* hqspi)
+{
+  if(hqspi->Instance==QUADSPI)
+  {
+  /* USER CODE BEGIN QUADSPI_MspDeInit 0 */
+
+  /* USER CODE END QUADSPI_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_QSPI_CLK_DISABLE();
+
+    /**QUADSPI GPIO Configuration
+    PA3     ------> QUADSPI_CLK
+    PB0     ------> QUADSPI_BK1_IO1
+    PB1     ------> QUADSPI_BK1_IO0
+    PB11     ------> QUADSPI_BK1_NCS
+    */
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_3);
+
+    HAL_GPIO_DeInit(GPIOB, GPIO_PIN_0|GPIO_PIN_1|GPIO_PIN_11);
+
+  /* USER CODE BEGIN QUADSPI_MspDeInit 1 */
+
+  /* USER CODE END QUADSPI_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief RTC MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hrtc: RTC handle pointer
+* @retval None
+*/
+void HAL_RTC_MspInit(RTC_HandleTypeDef* hrtc)
+{
+  RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+  if(hrtc->Instance==RTC)
+  {
+  /* USER CODE BEGIN RTC_MspInit 0 */
+
+  /* USER CODE END RTC_MspInit 0 */
+
+  /** Initializes the peripherals clock
+  */
+    PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_RTC;
+    PeriphClkInit.RTCClockSelection = RCC_RTCCLKSOURCE_LSE;
+    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK)
+    {
+      Error_Handler();
+    }
+
+    /* Peripheral clock enable */
+    __HAL_RCC_RTC_ENABLE();
+  /* USER CODE BEGIN RTC_MspInit 1 */
+
+  /* USER CODE END RTC_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief RTC MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hrtc: RTC handle pointer
+* @retval None
+*/
+void HAL_RTC_MspDeInit(RTC_HandleTypeDef* hrtc)
+{
+  if(hrtc->Instance==RTC)
+  {
+  /* USER CODE BEGIN RTC_MspDeInit 0 */
+
+  /* USER CODE END RTC_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_RTC_DISABLE();
+  /* USER CODE BEGIN RTC_MspDeInit 1 */
+
+  /* USER CODE END RTC_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief SD MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hsd: SD handle pointer
+* @retval None
+*/
+void HAL_SD_MspInit(SD_HandleTypeDef* hsd)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hsd->Instance==SDMMC1)
+  {
+  /* USER CODE BEGIN SDMMC1_MspInit 0 */
+
+  /* USER CODE END SDMMC1_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_SDMMC1_CLK_ENABLE();
+
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    __HAL_RCC_GPIOD_CLK_ENABLE();
+    /**SDMMC1 GPIO Configuration
+    PC8     ------> SDMMC1_D0
+    PC12     ------> SDMMC1_CK
+    PD2     ------> SDMMC1_CMD
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_8|GPIO_PIN_12;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF12_SDMMC1;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_2;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF12_SDMMC1;
+    HAL_GPIO_Init(GPIOD, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN SDMMC1_MspInit 1 */
+
+  /* USER CODE END SDMMC1_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief SD MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hsd: SD handle pointer
+* @retval None
+*/
+void HAL_SD_MspDeInit(SD_HandleTypeDef* hsd)
+{
+  if(hsd->Instance==SDMMC1)
+  {
+  /* USER CODE BEGIN SDMMC1_MspDeInit 0 */
+
+  /* USER CODE END SDMMC1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SDMMC1_CLK_DISABLE();
+
+    /**SDMMC1 GPIO Configuration
+    PC8     ------> SDMMC1_D0
+    PC12     ------> SDMMC1_CK
+    PD2     ------> SDMMC1_CMD
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_8|GPIO_PIN_12);
+
+    HAL_GPIO_DeInit(GPIOD, GPIO_PIN_2);
+
+  /* USER CODE BEGIN SDMMC1_MspDeInit 1 */
+
+  /* USER CODE END SDMMC1_MspDeInit 1 */
+  }
+
+}
+
+/**
+* @brief SPI MSP Initialization
+* This function configures the hardware resources used in this example
+* @param hspi: SPI handle pointer
+* @retval None
+*/
+void HAL_SPI_MspInit(SPI_HandleTypeDef* hspi)
+{
+  GPIO_InitTypeDef GPIO_InitStruct = {0};
+  if(hspi->Instance==SPI1)
+  {
+  /* USER CODE BEGIN SPI1_MspInit 0 */
+
+  /* USER CODE END SPI1_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_SPI1_CLK_ENABLE();
+
+    __HAL_RCC_GPIOA_CLK_ENABLE();
+    /**SPI1 GPIO Configuration
+    PA1     ------> SPI1_SCK
+    PA6     ------> SPI1_MISO
+    PA12     ------> SPI1_MOSI
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_1|GPIO_PIN_6|GPIO_PIN_12;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF5_SPI1;
+    HAL_GPIO_Init(GPIOA, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN SPI1_MspInit 1 */
+
+  /* USER CODE END SPI1_MspInit 1 */
+  }
+  else if(hspi->Instance==SPI3)
+  {
+  /* USER CODE BEGIN SPI3_MspInit 0 */
+
+  /* USER CODE END SPI3_MspInit 0 */
+    /* Peripheral clock enable */
+    __HAL_RCC_SPI3_CLK_ENABLE();
+
+    __HAL_RCC_GPIOC_CLK_ENABLE();
+    __HAL_RCC_GPIOB_CLK_ENABLE();
+    /**SPI3 GPIO Configuration
+    PC10     ------> SPI3_SCK
+    PC11     ------> SPI3_MISO
+    PB5     ------> SPI3_MOSI
+    */
+    GPIO_InitStruct.Pin = GPIO_PIN_10|GPIO_PIN_11;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF6_SPI3;
+    HAL_GPIO_Init(GPIOC, &GPIO_InitStruct);
+
+    GPIO_InitStruct.Pin = GPIO_PIN_5;
+    GPIO_InitStruct.Mode = GPIO_MODE_AF_PP;
+    GPIO_InitStruct.Pull = GPIO_NOPULL;
+    GPIO_InitStruct.Speed = GPIO_SPEED_FREQ_VERY_HIGH;
+    GPIO_InitStruct.Alternate = GPIO_AF6_SPI3;
+    HAL_GPIO_Init(GPIOB, &GPIO_InitStruct);
+
+  /* USER CODE BEGIN SPI3_MspInit 1 */
+
+  /* USER CODE END SPI3_MspInit 1 */
+  }
+
+}
+
+/**
+* @brief SPI MSP De-Initialization
+* This function freeze the hardware resources used in this example
+* @param hspi: SPI handle pointer
+* @retval None
+*/
+void HAL_SPI_MspDeInit(SPI_HandleTypeDef* hspi)
+{
+  if(hspi->Instance==SPI1)
+  {
+  /* USER CODE BEGIN SPI1_MspDeInit 0 */
+
+  /* USER CODE END SPI1_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SPI1_CLK_DISABLE();
+
+    /**SPI1 GPIO Configuration
+    PA1     ------> SPI1_SCK
+    PA6     ------> SPI1_MISO
+    PA12     ------> SPI1_MOSI
+    */
+    HAL_GPIO_DeInit(GPIOA, GPIO_PIN_1|GPIO_PIN_6|GPIO_PIN_12);
+
+  /* USER CODE BEGIN SPI1_MspDeInit 1 */
+
+  /* USER CODE END SPI1_MspDeInit 1 */
+  }
+  else if(hspi->Instance==SPI3)
+  {
+  /* USER CODE BEGIN SPI3_MspDeInit 0 */
+
+  /* USER CODE END SPI3_MspDeInit 0 */
+    /* Peripheral clock disable */
+    __HAL_RCC_SPI3_CLK_DISABLE();
+
+    /**SPI3 GPIO Configuration
+    PC10     ------> SPI3_SCK
+    PC11     ------> SPI3_MISO
+    PB5     ------> SPI3_MOSI
+    */
+    HAL_GPIO_DeInit(GPIOC, GPIO_PIN_10|GPIO_PIN_11);
+
+    HAL_GPIO_DeInit(GPIOB, GPIO_PIN_5);
+
+  /* USER CODE BEGIN SPI3_MspDeInit 1 */
+
+  /* USER CODE END SPI3_MspDeInit 1 */
+  }
 
 }
 

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/CubeMX_Config/Core/Src/stm32l4xx_it.c

@@ -66,7 +66,8 @@
 /**
   * @brief This function handles Non maskable interrupt.
   */
-void NMI_Handler(void) {
+void NMI_Handler(void)
+{
   /* USER CODE BEGIN NonMaskableInt_IRQn 0 */
 
   /* USER CODE END NonMaskableInt_IRQn 0 */
@@ -79,11 +80,13 @@ void NMI_Handler(void) {
 /**
   * @brief This function handles Hard fault interrupt.
   */
-void HardFault_Handler(void) {
+void HardFault_Handler(void)
+{
   /* USER CODE BEGIN HardFault_IRQn 0 */
 
   /* USER CODE END HardFault_IRQn 0 */
-    while (1) {
+  while (1)
+  {
     /* USER CODE BEGIN W1_HardFault_IRQn 0 */
     /* USER CODE END W1_HardFault_IRQn 0 */
   }
@@ -92,11 +95,13 @@ void HardFault_Handler(void) {
 /**
   * @brief This function handles Memory management fault.
   */
-void MemManage_Handler(void) {
+void MemManage_Handler(void)
+{
   /* USER CODE BEGIN MemoryManagement_IRQn 0 */
 
   /* USER CODE END MemoryManagement_IRQn 0 */
-    while (1) {
+  while (1)
+  {
     /* USER CODE BEGIN W1_MemoryManagement_IRQn 0 */
     /* USER CODE END W1_MemoryManagement_IRQn 0 */
   }
@@ -105,11 +110,13 @@ void MemManage_Handler(void) {
 /**
   * @brief This function handles Prefetch fault, memory access fault.
   */
-void BusFault_Handler(void) {
+void BusFault_Handler(void)
+{
   /* USER CODE BEGIN BusFault_IRQn 0 */
 
   /* USER CODE END BusFault_IRQn 0 */
-    while (1) {
+  while (1)
+  {
     /* USER CODE BEGIN W1_BusFault_IRQn 0 */
     /* USER CODE END W1_BusFault_IRQn 0 */
   }
@@ -118,11 +125,13 @@ void BusFault_Handler(void) {
 /**
   * @brief This function handles Undefined instruction or illegal state.
   */
-void UsageFault_Handler(void) {
+void UsageFault_Handler(void)
+{
   /* USER CODE BEGIN UsageFault_IRQn 0 */
 
   /* USER CODE END UsageFault_IRQn 0 */
-    while (1) {
+  while (1)
+  {
     /* USER CODE BEGIN W1_UsageFault_IRQn 0 */
     /* USER CODE END W1_UsageFault_IRQn 0 */
   }
@@ -131,7 +140,8 @@ void UsageFault_Handler(void) {
 /**
   * @brief This function handles System service call via SWI instruction.
   */
-void SVC_Handler(void) {
+void SVC_Handler(void)
+{
   /* USER CODE BEGIN SVCall_IRQn 0 */
 
   /* USER CODE END SVCall_IRQn 0 */
@@ -143,7 +153,8 @@ void SVC_Handler(void) {
 /**
   * @brief This function handles Debug monitor.
   */
-void DebugMon_Handler(void) {
+void DebugMon_Handler(void)
+{
   /* USER CODE BEGIN DebugMonitor_IRQn 0 */
 
   /* USER CODE END DebugMonitor_IRQn 0 */
@@ -155,7 +166,8 @@ void DebugMon_Handler(void) {
 /**
   * @brief This function handles Pendable request for system service.
   */
-void PendSV_Handler(void) {
+void PendSV_Handler(void)
+{
   /* USER CODE BEGIN PendSV_IRQn 0 */
 
   /* USER CODE END PendSV_IRQn 0 */
@@ -167,7 +179,8 @@ void PendSV_Handler(void) {
 /**
   * @brief This function handles System tick timer.
   */
-void SysTick_Handler(void) {
+void SysTick_Handler(void)
+{
   /* USER CODE BEGIN SysTick_IRQn 0 */
 
   /* USER CODE END SysTick_IRQn 0 */

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/CubeMX_Config/CubeMX_Config.ioc

@@ -1,4 +1,12 @@
 #MicroXplorer Configuration settings - do not modify
+ADC1.Channel-0\#ChannelRegularConversion=ADC_CHANNEL_3
+ADC1.CommonPathInternal=null|null|null|null
+ADC1.IPParameters=Rank-0\#ChannelRegularConversion,master,Channel-0\#ChannelRegularConversion,SamplingTime-0\#ChannelRegularConversion,OffsetNumber-0\#ChannelRegularConversion,NbrOfConversionFlag,CommonPathInternal
+ADC1.NbrOfConversionFlag=1
+ADC1.OffsetNumber-0\#ChannelRegularConversion=ADC_OFFSET_NONE
+ADC1.Rank-0\#ChannelRegularConversion=1
+ADC1.SamplingTime-0\#ChannelRegularConversion=ADC_SAMPLETIME_2CYCLES_5
+ADC1.master=1
 CAD.formats=
 CAD.pinconfig=
 CAD.provider=
@@ -7,27 +15,61 @@ GPIO.groupedBy=
 KeepUserPlacement=false
 Mcu.CPN=STM32L431RCT6
 Mcu.Family=STM32L4
-Mcu.IP0=NVIC
+Mcu.IP0=ADC1
-Mcu.IP1=RCC
+Mcu.IP1=DAC1
-Mcu.IP2=SYS
+Mcu.IP10=SYS
-Mcu.IP3=USART2
+Mcu.IP11=USART1
-Mcu.IPNb=4
+Mcu.IP12=USART2
+Mcu.IP13=USART3
+Mcu.IP2=LPUART1
+Mcu.IP3=NVIC
+Mcu.IP4=QUADSPI
+Mcu.IP5=RCC
+Mcu.IP6=RTC
+Mcu.IP7=SDMMC1
+Mcu.IP8=SPI1
+Mcu.IP9=SPI3
+Mcu.IPNb=14
 Mcu.Name=STM32L431R(B-C)Tx
 Mcu.Package=LQFP64
 Mcu.Pin0=PC13
-Mcu.Pin1=PH0-OSC_IN (PH0)
+Mcu.Pin1=PC14-OSC32_IN (PC14)
-Mcu.Pin2=PH1-OSC_OUT (PH1)
+Mcu.Pin10=PA4
-Mcu.Pin3=PA2
+Mcu.Pin11=PA6
-Mcu.Pin4=PA3
+Mcu.Pin12=PC4
-Mcu.Pin5=PA13 (JTMS-SWDIO)
+Mcu.Pin13=PC5
-Mcu.Pin6=PA14 (JTCK-SWCLK)
+Mcu.Pin14=PB0
-Mcu.Pin7=VP_SYS_VS_Systick
+Mcu.Pin15=PB1
-Mcu.PinsNb=8
+Mcu.Pin16=PB10
+Mcu.Pin17=PB11
+Mcu.Pin18=PC8
+Mcu.Pin19=PA9
+Mcu.Pin2=PC15-OSC32_OUT (PC15)
+Mcu.Pin20=PA10
+Mcu.Pin21=PA12
+Mcu.Pin22=PA13 (JTMS-SWDIO)
+Mcu.Pin23=PA14 (JTCK-SWCLK)
+Mcu.Pin24=PA15 (JTDI)
+Mcu.Pin25=PC10
+Mcu.Pin26=PC11
+Mcu.Pin27=PC12
+Mcu.Pin28=PD2
+Mcu.Pin29=PB5
+Mcu.Pin3=PH0-OSC_IN (PH0)
+Mcu.Pin30=VP_RTC_VS_RTC_Activate
+Mcu.Pin31=VP_SYS_VS_Systick
+Mcu.Pin4=PH1-OSC_OUT (PH1)
+Mcu.Pin5=PC1
+Mcu.Pin6=PC2
+Mcu.Pin7=PA1
+Mcu.Pin8=PA2
+Mcu.Pin9=PA3
+Mcu.PinsNb=32
 Mcu.ThirdPartyNb=0
 Mcu.UserConstants=
 Mcu.UserName=STM32L431RCTx
-MxCube.Version=6.9.2
+MxCube.Version=6.11.0
-MxDb.Version=DB.6.0.92
+MxDb.Version=DB.6.0.110
 NVIC.BusFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
 NVIC.DebugMonitor_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
 NVIC.ForceEnableDMAVector=true
@@ -39,16 +81,61 @@ NVIC.PriorityGroup=NVIC_PRIORITYGROUP_4
 NVIC.SVCall_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
 NVIC.SysTick_IRQn=true\:15\:0\:false\:false\:true\:false\:true\:false
 NVIC.UsageFault_IRQn=true\:0\:0\:false\:false\:true\:false\:false\:false
+PA1.Mode=Full_Duplex_Master
+PA1.Signal=SPI1_SCK
+PA10.Mode=Asynchronous
+PA10.Signal=USART1_RX
+PA12.Locked=true
+PA12.Mode=Full_Duplex_Master
+PA12.Signal=SPI1_MOSI
 PA13\ (JTMS-SWDIO).Mode=Serial_Wire
 PA13\ (JTMS-SWDIO).Signal=SYS_JTMS-SWDIO
 PA14\ (JTCK-SWCLK).Mode=Serial_Wire
 PA14\ (JTCK-SWCLK).Signal=SYS_JTCK-SWCLK
+PA15\ (JTDI).Mode=Asynchronous
+PA15\ (JTDI).Signal=USART2_RX
 PA2.Mode=Asynchronous
 PA2.Signal=USART2_TX
-PA3.Mode=Asynchronous
+PA3.Mode=Single Bank 1 2IOs
-PA3.Signal=USART2_RX
+PA3.Signal=QUADSPI_CLK
+PA4.Signal=COMP_DAC11_group
+PA6.Mode=Full_Duplex_Master
+PA6.Signal=SPI1_MISO
+PA9.Mode=Asynchronous
+PA9.Signal=USART1_TX
+PB0.Mode=Single Bank 1 2IOs
+PB0.Signal=QUADSPI_BK1_IO1
+PB1.Mode=Single Bank 1 2IOs
+PB1.Signal=QUADSPI_BK1_IO0
+PB10.Mode=Asynchronous
+PB10.Signal=LPUART1_RX
+PB11.Mode=Single Bank 1 2IOs
+PB11.Signal=QUADSPI_BK1_NCS
+PB5.Mode=Full_Duplex_Master
+PB5.Signal=SPI3_MOSI
+PC1.Mode=Asynchronous
+PC1.Signal=LPUART1_TX
+PC10.Mode=Full_Duplex_Master
+PC10.Signal=SPI3_SCK
+PC11.Mode=Full_Duplex_Master
+PC11.Signal=SPI3_MISO
+PC12.Mode=SD_1_bit
+PC12.Signal=SDMMC1_CK
 PC13.Locked=true
 PC13.Signal=GPIO_Output
+PC14-OSC32_IN\ (PC14).Mode=LSE-External-Oscillator
+PC14-OSC32_IN\ (PC14).Signal=RCC_OSC32_IN
+PC15-OSC32_OUT\ (PC15).Mode=LSE-External-Oscillator
+PC15-OSC32_OUT\ (PC15).Signal=RCC_OSC32_OUT
+PC2.Signal=ADCx_IN3
+PC4.Mode=Asynchronous
+PC4.Signal=USART3_TX
+PC5.Mode=Asynchronous
+PC5.Signal=USART3_RX
+PC8.Mode=SD_1_bit
+PC8.Signal=SDMMC1_D0
+PD2.Mode=SD_1_bit
+PD2.Signal=SDMMC1_CMD
 PH0-OSC_IN\ (PH0).Mode=HSE-External-Oscillator
 PH0-OSC_IN\ (PH0).Signal=RCC_OSC_IN
 PH1-OSC_OUT\ (PH1).Mode=HSE-External-Oscillator
@@ -72,7 +159,7 @@ ProjectManager.LastFirmware=true
 ProjectManager.LibraryCopy=0
 ProjectManager.MainLocation=Core/Src
 ProjectManager.NoMain=false
-ProjectManager.PreviousToolchain=
+ProjectManager.PreviousToolchain=STM32CubeIDE
 ProjectManager.ProjectBuild=false
 ProjectManager.ProjectFileName=CubeMX_Config.ioc
 ProjectManager.ProjectName=CubeMX_Config
@@ -84,7 +171,9 @@ ProjectManager.ToolChainLocation=
 ProjectManager.UAScriptAfterPath=
 ProjectManager.UAScriptBeforePath=
 ProjectManager.UnderRoot=false
-ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_USART2_UART_Init-USART2-false-HAL-true
+ProjectManager.functionlistsort=1-SystemClock_Config-RCC-false-HAL-false,2-MX_GPIO_Init-GPIO-false-HAL-true,3-MX_USART2_UART_Init-USART2-false-HAL-true,4-MX_ADC1_Init-ADC1-false-HAL-true,5-MX_DAC1_Init-DAC1-false-HAL-true,6-MX_LPUART1_UART_Init-LPUART1-false-HAL-true,7-MX_USART1_UART_Init-USART1-false-HAL-true,8-MX_USART3_UART_Init-USART3-false-HAL-true,9-MX_QUADSPI_Init-QUADSPI-false-HAL-true,10-MX_SDMMC1_SD_Init-SDMMC1-false-HAL-true,11-MX_SPI1_Init-SPI1-false-HAL-true,12-MX_SPI3_Init-SPI3-false-HAL-true,13-MX_RTC_Init-RTC-false-HAL-true
+QUADSPI.FlashSize=7
+QUADSPI.IPParameters=FlashSize
 RCC.ADCFreq_Value=32000000
 RCC.AHBFreq_Value=80000000
 RCC.APB1Freq_Value=80000000
@@ -101,12 +190,11 @@ RCC.HSI_VALUE=16000000
 RCC.I2C1Freq_Value=80000000
 RCC.I2C2Freq_Value=80000000
 RCC.I2C3Freq_Value=80000000
-RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,CortexFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI48_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSE_VALUE,LSI_VALUE,MCO1PinFreq_Value,MSI_VALUE,PLLN,PLLPoutputFreq_Value,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PLLSAI1PoutputFreq_Value,PLLSAI1QoutputFreq_Value,PLLSAI1RoutputFreq_Value,PLLSourceVirtual,PWRFreq_Value,RNGFreq_Value,SAI1Freq_Value,SDMMCFreq_Value,SWPMI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAI1OutputFreq_Value
+RCC.IPParameters=ADCFreq_Value,AHBFreq_Value,APB1Freq_Value,APB1TimFreq_Value,APB2Freq_Value,APB2TimFreq_Value,CortexFreq_Value,FCLKCortexFreq_Value,FamilyName,HCLKFreq_Value,HSE_VALUE,HSI48_VALUE,HSI_VALUE,I2C1Freq_Value,I2C2Freq_Value,I2C3Freq_Value,LPTIM1Freq_Value,LPTIM2Freq_Value,LPUART1Freq_Value,LSCOPinFreq_Value,LSI_VALUE,MCO1PinFreq_Value,MSI_VALUE,PLLN,PLLPoutputFreq_Value,PLLQoutputFreq_Value,PLLRCLKFreq_Value,PLLSAI1PoutputFreq_Value,PLLSAI1QoutputFreq_Value,PLLSAI1RoutputFreq_Value,PLLSourceVirtual,PWRFreq_Value,RNGFreq_Value,RTCClockSelection,RTCFreq_Value,SAI1Freq_Value,SDMMCFreq_Value,SWPMI1Freq_Value,SYSCLKFreq_VALUE,SYSCLKSource,USART1Freq_Value,USART2Freq_Value,USART3Freq_Value,VCOInputFreq_Value,VCOOutputFreq_Value,VCOSAI1OutputFreq_Value
 RCC.LPTIM1Freq_Value=80000000
 RCC.LPTIM2Freq_Value=80000000
 RCC.LPUART1Freq_Value=80000000
 RCC.LSCOPinFreq_Value=32000
-RCC.LSE_VALUE=32768
 RCC.LSI_VALUE=32000
 RCC.MCO1PinFreq_Value=80000000
 RCC.MSI_VALUE=4000000
@@ -120,6 +208,8 @@ RCC.PLLSAI1RoutputFreq_Value=32000000
 RCC.PLLSourceVirtual=RCC_PLLSOURCE_HSE
 RCC.PWRFreq_Value=80000000
 RCC.RNGFreq_Value=32000000
+RCC.RTCClockSelection=RCC_RTCCLKSOURCE_LSE
+RCC.RTCFreq_Value=32768
 RCC.SAI1Freq_Value=9142857.142857144
 RCC.SDMMCFreq_Value=32000000
 RCC.SWPMI1Freq_Value=80000000
@@ -131,8 +221,28 @@ RCC.USART3Freq_Value=80000000
 RCC.VCOInputFreq_Value=8000000
 RCC.VCOOutputFreq_Value=160000000
 RCC.VCOSAI1OutputFreq_Value=64000000
+SH.ADCx_IN3.0=ADC1_IN3,IN3-Single-Ended
+SH.ADCx_IN3.ConfNb=1
+SH.COMP_DAC11_group.0=DAC1_OUT1,DAC_OUT1
+SH.COMP_DAC11_group.ConfNb=1
+SPI1.CalculateBaudRate=40.0 MBits/s
+SPI1.Direction=SPI_DIRECTION_2LINES
+SPI1.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
+SPI1.Mode=SPI_MODE_MASTER
+SPI1.VirtualType=VM_MASTER
+SPI3.CalculateBaudRate=40.0 MBits/s
+SPI3.Direction=SPI_DIRECTION_2LINES
+SPI3.IPParameters=VirtualType,Mode,Direction,CalculateBaudRate
+SPI3.Mode=SPI_MODE_MASTER
+SPI3.VirtualType=VM_MASTER
+USART1.IPParameters=VirtualMode-Asynchronous
+USART1.VirtualMode-Asynchronous=VM_ASYNC
 USART2.IPParameters=VirtualMode-Asynchronous
 USART2.VirtualMode-Asynchronous=VM_ASYNC
+USART3.IPParameters=VirtualMode-Asynchronous
+USART3.VirtualMode-Asynchronous=VM_ASYNC
+VP_RTC_VS_RTC_Activate.Mode=RTC_Enabled
+VP_RTC_VS_RTC_Activate.Signal=RTC_VS_RTC_Activate
 VP_SYS_VS_Systick.Mode=SysTick
 VP_SYS_VS_Systick.Signal=SYS_VS_Systick
 board=custom

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/Kconfig

@@ -23,16 +23,107 @@ menu "On-chip Peripheral Drivers"
         default y
         select RT_USING_SERIAL
         if BSP_USING_UART
+             config BSP_USING_UART1
+                bool "Enable UART1(External Debug)"
+                default n
+
             config BSP_USING_UART2
-                bool "Enable UART2"
+                bool "Enable UART2(CH340)"
                 default y
 
+             config BSP_USING_UART3
+                bool "Enable UART3(E53)"
+                default n
+
+            config BSP_USING_LPUART1
+                bool "Enable LPUART1(WAN AT UART)"
+                default n
             config BSP_UART1_RX_USING_DMA
-                bool "Enable UART2 RX DMA"
+                bool "Enable UART1 RX DMA"
                 depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                 default n
         endif
     
+    menuconfig BSP_USING_ADC
+        bool "Enable ADC"
+        default n
+        select RT_USING_ADC
+        if BSP_USING_ADC
+            config BSP_USING_ADC1
+                bool "Enable ADC1(E53 LAN Interface)"
+                default n
+        endif
+
+    menuconfig BSP_USING_ONCHIP_RTC
+        bool "Enable RTC"
+        select RT_USING_RTC
+        default n
+        if BSP_USING_ONCHIP_RTC
+            choice
+                prompt "Select clock source"
+                default BSP_RTC_USING_LSE
+
+                config BSP_RTC_USING_LSE
+                    bool "RTC USING LSE"
+
+                config BSP_RTC_USING_LSI
+                    bool "RTC USING LSI"
+            endchoice
+        endif
+
+    menuconfig BSP_USING_DAC
+        bool "Enable DAC"
+        default n
+        select RT_USING_DAC
+        if BSP_USING_DAC
+            config BSP_USING_DAC1
+                bool "Enable DAC1(E53 LAN Interface)"
+                default n
+        endif
+
+    menuconfig BSP_USING_SPI
+        bool "Enable SPI BUS"
+        default n
+        select RT_USING_SPI
+        if BSP_USING_SPI
+            config BSP_USING_SPI1
+                bool "Enable SPI1 BUS(E53 LAN Interface)"
+                default n
+
+            config BSP_USING_SPI3
+                bool "Enable SPI3 BUS(WAN Interface)"
+                default n
+        endif
+    
+    config BSP_USING_QSPI_FLASH
+        bool "Enable QSPI FLASH (NAND Flash 8MB)"
+        select BSP_USING_QSPI
+        select RT_USING_SFUD
+        select RT_SFUD_USING_SFDP
+        default n 
+
+    config BSP_USING_SDCARD
+        bool "Enable SDCARD (sdio)"
+        select BSP_USING_SDIO
+        default n
+    
+    menuconfig BSP_USING_I2C1
+        bool "Enable I2C1 BUS (software simulation)"
+        default n
+        select RT_USING_I2C
+        select RT_USING_I2C_BITOPS
+        select RT_USING_PIN
+        if BSP_USING_I2C1
+            config BSP_I2C1_SCL_PIN
+                int "i2c1 scl pin number"
+                range 1 216
+                default 22
+            config BSP_I2C1_SDA_PIN
+                int "I2C1 sda pin number"
+                range 1 216
+                default 25
+        endif
+
     source "../libraries/HAL_Drivers/drivers/Kconfig"
 
 endmenu

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/board.c

@@ -5,7 +5,7 @@
  *
  * Change Logs:
  * Date              Author         Notes
- * 2018-11-06     SummerGift   first version
+ * 2024-3-19     RuiXuan Zhang   first version
  */
 
 #include "board.h"
@@ -14,23 +14,27 @@
   * @brief System Clock Configuration
   * @retval None
   */
-void SystemClock_Config(void)
+void SystemClock_Config(void) {
-{
     RCC_OscInitTypeDef RCC_OscInitStruct = {0};
     RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};
 
     /** Configure the main internal regulator output voltage
     */
-  if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1) != HAL_OK)
+    if (HAL_PWREx_ControlVoltageScaling(PWR_REGULATOR_VOLTAGE_SCALE1) != HAL_OK) {
-  {
         Error_Handler();
     }
 
+    /** Configure LSE Drive Capability
+    */
+    HAL_PWR_EnableBkUpAccess();
+    __HAL_RCC_LSEDRIVE_CONFIG(RCC_LSEDRIVE_LOW);
+
     /** Initializes the RCC Oscillators according to the specified parameters
     * in the RCC_OscInitTypeDef structure.
     */
-  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;
+    RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE | RCC_OSCILLATORTYPE_LSE;
     RCC_OscInitStruct.HSEState = RCC_HSE_ON;
+    RCC_OscInitStruct.LSEState = RCC_LSE_ON;
     RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;
     RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;
     RCC_OscInitStruct.PLL.PLLM = 1;
@@ -38,8 +42,7 @@ void SystemClock_Config(void)
     RCC_OscInitStruct.PLL.PLLP = RCC_PLLP_DIV7;
     RCC_OscInitStruct.PLL.PLLQ = RCC_PLLQ_DIV2;
     RCC_OscInitStruct.PLL.PLLR = RCC_PLLR_DIV2;
-  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)
+    if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK) {
-  {
         Error_Handler();
     }
 
@@ -52,8 +55,31 @@ void SystemClock_Config(void)
     RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV1;
     RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;
 
-  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK)
+    if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_4) != HAL_OK) {
-  {
+        Error_Handler();
+    }
+}
+
+/**
+  * @brief Peripherals Common Clock Configuration
+  * @retval None
+  */
+void PeriphCommonClock_Config(void) {
+    RCC_PeriphCLKInitTypeDef PeriphClkInit = {0};
+
+    /** Initializes the peripherals clock
+    */
+    PeriphClkInit.PeriphClockSelection = RCC_PERIPHCLK_SDMMC1 | RCC_PERIPHCLK_ADC;
+    PeriphClkInit.AdcClockSelection = RCC_ADCCLKSOURCE_PLLSAI1;
+    PeriphClkInit.Sdmmc1ClockSelection = RCC_SDMMC1CLKSOURCE_PLLSAI1;
+    PeriphClkInit.PLLSAI1.PLLSAI1Source = RCC_PLLSOURCE_HSE;
+    PeriphClkInit.PLLSAI1.PLLSAI1M = 1;
+    PeriphClkInit.PLLSAI1.PLLSAI1N = 8;
+    PeriphClkInit.PLLSAI1.PLLSAI1P = RCC_PLLP_DIV7;
+    PeriphClkInit.PLLSAI1.PLLSAI1Q = RCC_PLLQ_DIV2;
+    PeriphClkInit.PLLSAI1.PLLSAI1R = RCC_PLLR_DIV2;
+    PeriphClkInit.PLLSAI1.PLLSAI1ClockOut = RCC_PLLSAI1_48M2CLK | RCC_PLLSAI1_ADC1CLK;
+    if (HAL_RCCEx_PeriphCLKConfig(&PeriphClkInit) != HAL_OK) {
         Error_Handler();
     }
 }

bsp/stm32/stm32l431-tencentos-tiny-EVB_MX+/board/board.h

@@ -44,6 +44,8 @@ extern int __bss_end;
 
 void SystemClock_Config(void);
 
+void PeriphCommonClock_Config(void);
+
 #ifdef __cplusplus
 }
 #endif