[imxrt1170] update enet (#6244)

Co-authored-by: xinyi.gao <xinyi.gao@nxp.com>

bsp/imxrt/imxrt1052-nxp-evk/board/Kconfig

@@ -116,6 +116,7 @@ menu "Onboard Peripheral Drivers"
     menuconfig BSP_USING_ETH
 	bool "Enable Ethernet"
 	select RT_USING_NETDEV
+	select RT_USING_LWIP
 	default n
     
 

bsp/imxrt/imxrt1170-nxp-evk/board/Kconfig

@@ -17,7 +17,7 @@ menu "On-chip Peripheral Drivers"
     config BSP_USING_DMA
         bool "Enable DMA"
         default n
-        
+
     config BSP_USING_GPIO
         bool "Enable GPIO"
         select RT_USING_PIN
@@ -27,7 +27,7 @@ menu "On-chip Peripheral Drivers"
         bool "Enable UART"
         select RT_USING_SERIAL
         default y
-        
+
         if BSP_USING_LPUART
             config BSP_USING_LPUART1
                 bool "Enable LPUART1"
@@ -93,6 +93,46 @@ menu "Onboard Peripheral Drivers"
         bool "Enable SDRAM"
         default n
 
+    menuconfig BSP_USING_ETH
+    bool "Enable Ethernet"
+    select RT_USING_NETDEV
+    select RT_USING_LWIP
+    default n
+
+
+    if BSP_USING_ETH
+        config BSP_USING_PHY
+            select RT_USING_PHY
+            bool "Enable ethernet phy"
+            default y
+
+        if BSP_USING_PHY
+            config PHY_DEVICE_ADDRESS
+                int "Specify address of phy device"
+                default 2
+
+            config PHY_USING_KSZ8081
+                bool "i.MX RT1064EVK uses ksz8081 phy"
+                default y
+
+            if PHY_USING_KSZ8081
+                config PHY_RESET_PORT
+                    int "indicate port of reset"
+                    default 6
+
+                config PHY_RESET_PIN
+                    int "indicate pin of reset"
+                    default 12
+
+                config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
+                    bool "Enable the PHY ksz8081 RMII50M mode"
+                    depends on PHY_USING_KSZ8081
+                    default y
+            endif
+
+        endif
+    endif
+
 endmenu
 
 menu "Board extended module Drivers"

bsp/imxrt/libraries/MIMXRT1170/MIMXRT1176/MIMXRT1176_cm7_features.h

@@ -340,9 +340,9 @@
 /* @brief Support Interrupt Coalesce */
 #define FSL_FEATURE_ENET_HAS_INTERRUPT_COALESCE (1)
 /* @brief Queue Size. */
-#define FSL_FEATURE_ENET_QUEUE (3)
+#define FSL_FEATURE_ENET_QUEUE (1)
 /* @brief Has AVB Support. */
-#define FSL_FEATURE_ENET_HAS_AVB (1)
+#define FSL_FEATURE_ENET_HAS_AVB (0)
 /* @brief Has Timer Pulse Width control. */
 #define FSL_FEATURE_ENET_HAS_TIMER_PWCONTROL (1)
 /* @brief Has Extend MDIO Support. */

bsp/imxrt/libraries/MIMXRT1170/SConscript

@@ -2,7 +2,7 @@ Import('rtconfig')
 from building import *
 
 cwd = GetCurrentDir()
-path = [cwd + '/CMSIS/Include',cwd + '/MIMXRT1176', cwd + '/MIMXRT1176/drivers']
+path = [cwd + '/CMSIS/Include',cwd + '/MIMXRT1176', cwd + '/MIMXRT1176/drivers', cwd + '/MIMXRT1176/drivers/cm7']
 src = Split('''
             MIMXRT1176/drivers/fsl_anatop_ai.c
             MIMXRT1176/system_MIMXRT1176_cm7.c