rt-thread/bsp/renesas/ra6m4-iot/board/Kconfig

menu "Hardware Drivers Config"

    config SOC_R7FA6M4AF
        bool
        select SOC_SERIES_R7FA6M4
        select RT_USING_COMPONENTS_INIT
        select RT_USING_USER_MAIN
        default y

    menu "Onboard Peripheral Drivers"

    endmenu

    menu "On-chip Peripheral Drivers"

        source "../libraries/HAL_Drivers/Kconfig"

        menuconfig BSP_USING_UART
            bool "Enable UART"
            default y
            select RT_USING_SERIAL
            select RT_USING_SERIAL_V2
            if BSP_USING_UART

                menuconfig BSP_USING_UART0
                    bool "Enable UART0"
                    default n
                    if BSP_USING_UART0
                        config BSP_UART0_RX_USING_DMA
                            bool "Enable UART0 RX DMA"
                            depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART0_TX_USING_DMA
                            bool "Enable UART0 TX DMA"
                            depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART0_RX_BUFSIZE
                            int "Set UART0 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART0_TX_BUFSIZE
                            int "Set UART0 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART1
                    bool "Enable UART1"
                    default n
                    if BSP_USING_UART1
                        config BSP_UART1_RX_USING_DMA
                            bool "Enable UART1 RX DMA"
                            depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART1_TX_USING_DMA
                            bool "Enable UART1 TX DMA"
                            depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART1_RX_BUFSIZE
                            int "Set UART1 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART1_TX_BUFSIZE
                            int "Set UART1 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART2
                    bool "Enable UART2"
                    default n
                    if BSP_USING_UART2
                        config BSP_UART2_RX_USING_DMA
                            bool "Enable UART2 RX DMA"
                            depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART2_TX_USING_DMA
                            bool "Enable UART2 TX DMA"
                            depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART2_RX_BUFSIZE
                            int "Set UART2 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART2_TX_BUFSIZE
                            int "Set UART2 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART3
                    bool "Enable UART3"
                    default n
                    if BSP_USING_UART3
                        config BSP_UART3_RX_USING_DMA
                            bool "Enable UART3 RX DMA"
                            depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART3_TX_USING_DMA
                            bool "Enable UART3 TX DMA"
                            depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART3_RX_BUFSIZE
                            int "Set UART3 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART3_TX_BUFSIZE
                            int "Set UART3 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART4
                    bool "Enable UART4"
                    default n
                    if BSP_USING_UART4
                        config BSP_UART4_RX_USING_DMA
                            bool "Enable UART4 RX DMA"
                            depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART4_TX_USING_DMA
                            bool "Enable UART4 TX DMA"
                            depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART4_RX_BUFSIZE
                            int "Set UART4 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART4_TX_BUFSIZE
                            int "Set UART4 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART5
                    bool "Enable UART5"
                    default n
                    if BSP_USING_UART5
                        config BSP_UART5_RX_USING_DMA
                            bool "Enable UART5 RX DMA"
                            depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART5_TX_USING_DMA
                            bool "Enable UART5 TX DMA"
                            depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART5_RX_BUFSIZE
                            int "Set UART5 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART5_TX_BUFSIZE
                            int "Set UART5 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART6
                    bool "Enable UART6"
                    default n
                    if BSP_USING_UART6
                        config BSP_UART6_RX_USING_DMA
                            bool "Enable UART6 RX DMA"
                            depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART6_TX_USING_DMA
                            bool "Enable UART6 TX DMA"
                            depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART6_RX_BUFSIZE
                            int "Set UART6 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART6_TX_BUFSIZE
                            int "Set UART6 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART7
                    bool "Enable UART7"
                    default n
                    if BSP_USING_UART7
                        config BSP_UART7_RX_USING_DMA
                            bool "Enable UART7 RX DMA"
                            depends on BSP_USING_UART7 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART7_TX_USING_DMA
                            bool "Enable UART7 TX DMA"
                            depends on BSP_USING_UART7 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART7_RX_BUFSIZE
                            int "Set UART7 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART7_TX_BUFSIZE
                            int "Set UART7 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART8
                    bool "Enable UART8"
                    default n
                    if BSP_USING_UART8
                        config BSP_UART8_RX_USING_DMA
                            bool "Enable UART8 RX DMA"
                            depends on BSP_USING_UART8 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART8_TX_USING_DMA
                            bool "Enable UART8 TX DMA"
                            depends on BSP_USING_UART8 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART8_RX_BUFSIZE
                            int "Set UART8 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART8_TX_BUFSIZE
                            int "Set UART8 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif

                menuconfig BSP_USING_UART9
                    bool "Enable UART9"
                    default n
                    if BSP_USING_UART9
                        config BSP_UART9_RX_USING_DMA
                            bool "Enable UART9 RX DMA"
                            depends on BSP_USING_UART9 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART9_TX_USING_DMA
                            bool "Enable UART9 TX DMA"
                            depends on BSP_USING_UART9 && RT_SERIAL_USING_DMA
                            default n

                        config BSP_UART9_RX_BUFSIZE
                            int "Set UART9 RX buffer size"
                            range 64 65535
                            depends on RT_USING_SERIAL_V2
                            default 256

                        config BSP_UART9_TX_BUFSIZE
                            int "Set UART9 TX buffer size"
                            range 0 65535
                            depends on RT_USING_SERIAL_V2
                            default 0
                    endif
            endif

        menuconfig BSP_USING_I2C
            bool "Enable I2C BUS"
            default n
            select RT_USING_I2C
            select RT_USING_I2C_BITOPS
            select RT_USING_PIN
            if BSP_USING_I2C
                config BSP_USING_HW_I2C
                    bool "Enable Hardware I2C BUS"
                    default n
                if BSP_USING_HW_I2C
                    config BSP_USING_HW_I2C1
                        bool "Enable Hardware I2C1 BUS"
                        default n
                endif
                if !BSP_USING_HW_I2C
                    menuconfig BSP_USING_I2C1
                        bool "Enable I2C1 BUS (software simulation)"
                        default y
                        if BSP_USING_I2C1
                            config BSP_I2C1_SCL_PIN
                                hex "i2c1 scl pin number"
                                range 0x0000 0x0B0F
                                default 0x050C
                            config BSP_I2C1_SDA_PIN
                                hex "I2C1 sda pin number"
                                range 0x0000 0x0B0F
                                default 0x050B
                        endif
                endif
            endif

        menuconfig BSP_USING_SPI
            bool "Enable SPI BUS"
            default n
            select RT_USING_SPI
            if BSP_USING_SPI
                config BSP_SPI_USING_DTC_DMA
                    bool "Enable SPI DTC transfers data without using the CPU."
                    default n

                config BSP_USING_SPI0
                    bool "Enable SPI0 BUS"
                    default n

                config BSP_USING_SPI1
                    bool "Enable SPI1 BUS"
                    default n
            endif

        menuconfig BSP_USING_ADC
            bool "Enable ADC"
            default n
            select RT_USING_ADC
            if BSP_USING_ADC
                config BSP_USING_ADC0
                    bool "Enable ADC0"
                    default n

                config BSP_USING_ADC1
                    bool "Enable ADC1"
                    default n
            endif

        menuconfig BSP_USING_DAC
            bool "Enable DAC"
            default n
            select RT_USING_DAC
            if BSP_USING_DAC
                config BSP_USING_DAC0
                    bool "Enable DAC0"
                    default n

                config BSP_USING_DAC1
                    bool "Enable DAC1"
                    default n
            endif

        menuconfig BSP_USING_PWM
            bool "Enable PWM"
            default n
            select RT_USING_PWM
            if BSP_USING_PWM
                config BSP_USING_PWM0
                    bool "Enable GPT0 (32-Bits) output PWM"
                    default n

                config BSP_USING_PWM1
                    bool "Enable GPT1 (32-Bits) output PWM"
                    default n

                config BSP_USING_PWM2
                    bool "Enable GPT2 (32-Bits) output PWM"
                    default n

                config BSP_USING_PWM3
                    bool "Enable GPT3 (32-Bits) output PWM"
                    default n

                config BSP_USING_PWM4
                    bool "Enable GPT4 (16-Bits) output PWM"
                    default n

                config BSP_USING_PWM5
                    bool "Enable GPT5 (16-Bits) output PWM"
                    default n

                config BSP_USING_PWM6
                    bool "Enable GPT6 (16-Bits) output PWM"
                    default n

                config BSP_USING_PWM7
                    bool "Enable GPT7 (16-Bits) output PWM"
                    default n

                config BSP_USING_PWM8
                    bool "Enable GPT8 (16-Bits) output PWM"
                    default n

                config BSP_USING_PWM9
                    bool "Enable GPT9 (16-Bits) output PWM"
                    default n
            endif

        menuconfig BSP_USING_SDHI
            bool "Enable SDHI"
            default n
            select RT_USING_SDIO
            select RT_USING_DFS
            select RT_LIBC_USING_FILEIO
            select RT_USING_POSIX_DEVIO
            if BSP_USING_SDHI
                menuconfig BSP_USING_SDHI0
                    bool "Enable SDHI0"
                    default n
                    if BSP_USING_SDHI0
                        config SDHI_USING_1_BIT
                            bool "Use 1-bit Mode(4-bit when disable)"
                            default y
                    endif

                menuconfig BSP_USING_SDHI1
                    bool "Enable SDHI1"
                    default n
                    if BSP_USING_SDHI1
                        config SDHI_USING_1_BIT
                            bool "Use 1-bit Mode(4-bit when disable)"
                            default y
                    endif
                endif

        menuconfig BSP_USING_CAN
            bool "Enable CAN"
            default n
            select RT_USING_CAN
            if BSP_USING_CAN
                config BSP_USING_CAN0
                    bool "Enable CAN0"
                    default n

                config BSP_USING_CAN1
                    bool "Enable CAN1"
                    default n
            endif

    endmenu

    menu "Board extended module Drivers"

        menuconfig BSP_USING_RW007
            bool "Enable RW007"
            default n
            select PKG_USING_RW007
            select BSP_USING_SPI

        if BSP_USING_RW007
            config RA_RW007_SPI_BUS_NAME
                string "RW007 BUS NAME"
                default "spi1"

            config RA_RW007_CS_PIN
                hex "(HEX)CS pin index"
                default 0x040D

            config RA_RW007_BOOT0_PIN
                hex "(HEX)BOOT0 pin index (same as spi clk pin)"
                default 0x040C

            config RA_RW007_BOOT1_PIN
                hex "(HEX)BOOT1 pin index (same as spi cs pin)"
                default 0x040D

            config RA_RW007_INT_BUSY_PIN
                hex "(HEX)INT/BUSY pin index"
                default 0x0506

            config RA_RW007_RST_PIN
                hex "(HEX)RESET pin index"
                default 0x040F
        endif

        config BSP_USING_LWIP_PPP
            bool "Enable ppp function"
            default n
            select BSP_USING_UART
            select BSP_USING_UART2
            select PKG_USING_PPP_DEVICE

    endmenu
endmenu
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00			`menu "Hardware Drivers Config"`

			`config SOC_R7FA6M4AF`
			`bool`
			`select SOC_SERIES_R7FA6M4`
			`select RT_USING_COMPONENTS_INIT`
			`select RT_USING_USER_MAIN`
			`default y`

			`menu "Onboard Peripheral Drivers"`

			`endmenu`

			`menu "On-chip Peripheral Drivers"`

			`source "../libraries/HAL_Drivers/Kconfig"`

			`menuconfig BSP_USING_UART`
			`bool "Enable UART"`
			`default y`
			`select RT_USING_SERIAL`
			`select RT_USING_SERIAL_V2`
			`if BSP_USING_UART`

			`menuconfig BSP_USING_UART0`
			`bool "Enable UART0"`
			`default n`
			`if BSP_USING_UART0`
			`config BSP_UART0_RX_USING_DMA`
			`bool "Enable UART0 RX DMA"`
			`depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART0_TX_USING_DMA`
			`bool "Enable UART0 TX DMA"`
			`depends on BSP_USING_UART0 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART0_RX_BUFSIZE`
			`int "Set UART0 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART0_TX_BUFSIZE`
			`int "Set UART0 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART1`
			`bool "Enable UART1"`
			`default n`
			`if BSP_USING_UART1`
			`config BSP_UART1_RX_USING_DMA`
			`bool "Enable UART1 RX DMA"`
			`depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART1_TX_USING_DMA`
			`bool "Enable UART1 TX DMA"`
			`depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART1_RX_BUFSIZE`
			`int "Set UART1 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART1_TX_BUFSIZE`
			`int "Set UART1 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART2`
			`bool "Enable UART2"`
			`default n`
			`if BSP_USING_UART2`
			`config BSP_UART2_RX_USING_DMA`
			`bool "Enable UART2 RX DMA"`
			`depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART2_TX_USING_DMA`
			`bool "Enable UART2 TX DMA"`
			`depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART2_RX_BUFSIZE`
			`int "Set UART2 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART2_TX_BUFSIZE`
			`int "Set UART2 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART3`
			`bool "Enable UART3"`
			`default n`
			`if BSP_USING_UART3`
			`config BSP_UART3_RX_USING_DMA`
			`bool "Enable UART3 RX DMA"`
			`depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART3_TX_USING_DMA`
			`bool "Enable UART3 TX DMA"`
			`depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART3_RX_BUFSIZE`
			`int "Set UART3 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART3_TX_BUFSIZE`
			`int "Set UART3 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART4`
			`bool "Enable UART4"`
			`default n`
			`if BSP_USING_UART4`
			`config BSP_UART4_RX_USING_DMA`
			`bool "Enable UART4 RX DMA"`
			`depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART4_TX_USING_DMA`
			`bool "Enable UART4 TX DMA"`
			`depends on BSP_USING_UART4 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART4_RX_BUFSIZE`
			`int "Set UART4 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART4_TX_BUFSIZE`
			`int "Set UART4 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART5`
			`bool "Enable UART5"`
			`default n`
			`if BSP_USING_UART5`
			`config BSP_UART5_RX_USING_DMA`
			`bool "Enable UART5 RX DMA"`
			`depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART5_TX_USING_DMA`
			`bool "Enable UART5 TX DMA"`
			`depends on BSP_USING_UART5 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART5_RX_BUFSIZE`
			`int "Set UART5 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART5_TX_BUFSIZE`
			`int "Set UART5 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART6`
			`bool "Enable UART6"`
			`default n`
			`if BSP_USING_UART6`
			`config BSP_UART6_RX_USING_DMA`
			`bool "Enable UART6 RX DMA"`
			`depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART6_TX_USING_DMA`
			`bool "Enable UART6 TX DMA"`
			`depends on BSP_USING_UART6 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART6_RX_BUFSIZE`
			`int "Set UART6 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART6_TX_BUFSIZE`
			`int "Set UART6 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART7`
			`bool "Enable UART7"`
			`default n`
			`if BSP_USING_UART7`
			`config BSP_UART7_RX_USING_DMA`
			`bool "Enable UART7 RX DMA"`
			`depends on BSP_USING_UART7 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART7_TX_USING_DMA`
			`bool "Enable UART7 TX DMA"`
			`depends on BSP_USING_UART7 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART7_RX_BUFSIZE`
			`int "Set UART7 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART7_TX_BUFSIZE`
			`int "Set UART7 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART8`
			`bool "Enable UART8"`
			`default n`
			`if BSP_USING_UART8`
			`config BSP_UART8_RX_USING_DMA`
			`bool "Enable UART8 RX DMA"`
			`depends on BSP_USING_UART8 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART8_TX_USING_DMA`
			`bool "Enable UART8 TX DMA"`
			`depends on BSP_USING_UART8 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART8_RX_BUFSIZE`
			`int "Set UART8 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART8_TX_BUFSIZE`
			`int "Set UART8 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`

			`menuconfig BSP_USING_UART9`
			`bool "Enable UART9"`
			`default n`
			`if BSP_USING_UART9`
			`config BSP_UART9_RX_USING_DMA`
			`bool "Enable UART9 RX DMA"`
			`depends on BSP_USING_UART9 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART9_TX_USING_DMA`
			`bool "Enable UART9 TX DMA"`
			`depends on BSP_USING_UART9 && RT_SERIAL_USING_DMA`
			`default n`

			`config BSP_UART9_RX_BUFSIZE`
			`int "Set UART9 RX buffer size"`
			`range 64 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 256`

			`config BSP_UART9_TX_BUFSIZE`
			`int "Set UART9 TX buffer size"`
			`range 0 65535`
			`depends on RT_USING_SERIAL_V2`
			`default 0`
			`endif`
			`endif`

			`menuconfig BSP_USING_I2C`
			`bool "Enable I2C BUS"`
			`default n`
			`select RT_USING_I2C`
			`select RT_USING_I2C_BITOPS`
			`select RT_USING_PIN`
			`if BSP_USING_I2C`
[[renesas/drivers] Fix error code issues 6183.Add hardware i2c driver. (#6279) * [renesas/ra2l1-cpk] add Captouch板载触摸按键配置说明.md * Update Captouch板载触摸按键配置说明.md * [renesas/drv_wdt.c] Fix error code issues [renesas/drv_i2c.c] add hardware i2c driver * [update] drv_wdt.c,drv_i2c.c Co-authored-by: Man, Jianting (Meco) <920369182@qq.com> 2022-08-15 21:25:42 +08:00			`config BSP_USING_HW_I2C`
			`bool "Enable Hardware I2C BUS"`
			`default n`
			`if BSP_USING_HW_I2C`
			`config BSP_USING_HW_I2C1`
			`bool "Enable Hardware I2C1 BUS"`
			`default n`
			`endif`
			`if !BSP_USING_HW_I2C`
			`menuconfig BSP_USING_I2C1`
			`bool "Enable I2C1 BUS (software simulation)"`
			`default y`
			`if BSP_USING_I2C1`
			`config BSP_I2C1_SCL_PIN`
			`hex "i2c1 scl pin number"`
			`range 0x0000 0x0B0F`
			`default 0x050C`
			`config BSP_I2C1_SDA_PIN`
			`hex "I2C1 sda pin number"`
			`range 0x0000 0x0B0F`
			`default 0x050B`
			`endif`
			`endif`
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00			`endif`

			`menuconfig BSP_USING_SPI`
			`bool "Enable SPI BUS"`
			`default n`
			`select RT_USING_SPI`
format Kconfig and sconscript 2023-01-09 10:14:23 +08:00			`if BSP_USING_SPI`
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00			`config BSP_SPI_USING_DTC_DMA`
			`bool "Enable SPI DTC transfers data without using the CPU."`
			`default n`

			`config BSP_USING_SPI0`
			`bool "Enable SPI0 BUS"`
			`default n`
format Kconfig and sconscript 2023-01-09 10:14:23 +08:00
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00			`config BSP_USING_SPI1`
			`bool "Enable SPI1 BUS"`
			`default n`
			`endif`

			`menuconfig BSP_USING_ADC`
			`bool "Enable ADC"`
			`default n`
			`select RT_USING_ADC`
			`if BSP_USING_ADC`
			`config BSP_USING_ADC0`
			`bool "Enable ADC0"`
			`default n`

			`config BSP_USING_ADC1`
			`bool "Enable ADC1"`
			`default n`
			`endif`

			`menuconfig BSP_USING_DAC`
			`bool "Enable DAC"`
			`default n`
			`select RT_USING_DAC`
			`if BSP_USING_DAC`
			`config BSP_USING_DAC0`
			`bool "Enable DAC0"`
			`default n`

			`config BSP_USING_DAC1`
			`bool "Enable DAC1"`
			`default n`
			`endif`

			`menuconfig BSP_USING_PWM`
			`bool "Enable PWM"`
			`default n`
			`select RT_USING_PWM`
			`if BSP_USING_PWM`
			`config BSP_USING_PWM0`
			`bool "Enable GPT0 (32-Bits) output PWM"`
			`default n`
format Kconfig and sconscript 2023-01-09 10:14:23 +08:00
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00			`config BSP_USING_PWM1`
			`bool "Enable GPT1 (32-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM2`
			`bool "Enable GPT2 (32-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM3`
			`bool "Enable GPT3 (32-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM4`
			`bool "Enable GPT4 (16-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM5`
			`bool "Enable GPT5 (16-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM6`
			`bool "Enable GPT6 (16-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM7`
			`bool "Enable GPT7 (16-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM8`
			`bool "Enable GPT8 (16-Bits) output PWM"`
			`default n`

			`config BSP_USING_PWM9`
			`bool "Enable GPT9 (16-Bits) output PWM"`
			`default n`
			`endif`

			`menuconfig BSP_USING_SDHI`
			`bool "Enable SDHI"`
			`default n`
			`select RT_USING_SDIO`
			`select RT_USING_DFS`
			`select RT_LIBC_USING_FILEIO`
sync branch rt-smart. (#6641) * Synchronize the code of the rt mart branch to the master branch. * TTY device * Add lwP code from rt-smart * Add vnode in DFS, but DFS will be re-write for rt-smart * There are three libcpu for rt-smart: * arm/cortex-a, arm/aarch64 * riscv64 Co-authored-by: Rbb666 <zhangbingru@rt-thread.com> Co-authored-by: zhkag <zhkag@foxmail.com> 2022-12-03 12:07:44 +08:00			`select RT_USING_POSIX_DEVIO`
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00			`if BSP_USING_SDHI`
[bsp][hmi-board] Optimize hardware driver configuration and trim the project file volume 2024-02-01 16:27:18 +08:00			`menuconfig BSP_USING_SDHI0`
			`bool "Enable SDHI0"`
			`default n`
			`if BSP_USING_SDHI0`
			`config SDHI_USING_1_BIT`
			`bool "Use 1-bit Mode(4-bit when disable)"`
			`default y`
			`endif`

			`menuconfig BSP_USING_SDHI1`
			`bool "Enable SDHI1"`
			`default n`
			`if BSP_USING_SDHI1`
			`config SDHI_USING_1_BIT`
			`bool "Use 1-bit Mode(4-bit when disable)"`
			`default y`
			`endif`
			`endif`
[update] 添加 RA 系列 BSP 开发教程： (#5598) - 添加 RA 系列 BSP 开发教程 - 添加 ra6m4-iot PPP 上网 - 整理驱动文件 2022-03-11 09:17:46 +08:00
			`menuconfig BSP_USING_CAN`
			`bool "Enable CAN"`
			`default n`
			`select RT_USING_CAN`
			`if BSP_USING_CAN`
			`config BSP_USING_CAN0`
			`bool "Enable CAN0"`
			`default n`

			`config BSP_USING_CAN1`
			`bool "Enable CAN1"`
			`default n`
			`endif`

			`endmenu`

			`menu "Board extended module Drivers"`

			`menuconfig BSP_USING_RW007`
			`bool "Enable RW007"`
			`default n`
			`select PKG_USING_RW007`
			`select BSP_USING_SPI`

			`if BSP_USING_RW007`
			`config RA_RW007_SPI_BUS_NAME`
			`string "RW007 BUS NAME"`
			`default "spi1"`

			`config RA_RW007_CS_PIN`
			`hex "(HEX)CS pin index"`
			`default 0x040D`

			`config RA_RW007_BOOT0_PIN`
			`hex "(HEX)BOOT0 pin index (same as spi clk pin)"`
			`default 0x040C`

			`config RA_RW007_BOOT1_PIN`
			`hex "(HEX)BOOT1 pin index (same as spi cs pin)"`
			`default 0x040D`

			`config RA_RW007_INT_BUSY_PIN`
			`hex "(HEX)INT/BUSY pin index"`
			`default 0x0506`

			`config RA_RW007_RST_PIN`
			`hex "(HEX)RESET pin index"`
			`default 0x040F`
			`endif`

			`config BSP_USING_LWIP_PPP`
			`bool "Enable ppp function"`
			`default n`
			`select BSP_USING_UART`
			`select BSP_USING_UART2`
			`select PKG_USING_PPP_DEVICE`

			`endmenu`
			`endmenu`