rt-thread/bsp/stm32/stm32f429-atk-apollo/board/Kconfig

249 lines
6.3 KiB
Plaintext
Raw Normal View History

menu "Hardware Drivers Config"
config SOC_STM32F429IG
bool
select SOC_SERIES_STM32F4
default y
menu "Onboard Peripheral Drivers"
config BSP_USING_USB_TO_USART
bool "Enable USB TO USART (uart1)"
2019-01-08 12:04:44 +08:00
select BSP_USING_UART
select BSP_USING_UART1
default y
config BSP_USING_COM2
2018-12-26 10:37:50 +08:00
bool "Enable COM2 (uart2 pin conflict with Ethernet and PWM)"
2019-01-08 12:04:44 +08:00
select BSP_USING_UART
select BSP_USING_UART2
default n
config BSP_USING_COM3
2018-12-26 10:37:50 +08:00
bool "Enable COM3 (uart3 pin conflict with Ethernet)"
select BSP_USING_UART3
default n
config BSP_USING_SDRAM
bool "Enable SDRAM"
select BSP_USING_FMC
default n
config BSP_USING_SPI_FLASH
bool "Enable SPI FLASH (w25q256 spi5)"
2019-01-08 12:04:44 +08:00
select BSP_USING_SPI
select BSP_USING_SPI5
select RT_USING_SFUD
select RT_SFUD_USING_SFDP
default n
config BSP_USING_MPU9250
bool "Enable MPU 9250 (i2c1)"
select BSP_USING_I2C1
select PKG_USING_MPU6XXX
default n
2018-12-26 10:37:50 +08:00
config PHY_USING_LAN8720A
bool
2018-12-26 18:12:48 +08:00
config BSP_USING_ETH
bool "Enable Ethernet"
2018-12-26 18:12:48 +08:00
select BSP_USING_I2C1
select PKG_USING_PCF8574
select RT_USING_LWIP
2018-12-26 10:37:50 +08:00
select PHY_USING_LAN8720A
2018-12-26 18:12:48 +08:00
default n
config BSP_USING_SDCARD
bool "Enable SDCARD (sdio)"
select BSP_USING_SDIO
select RT_USING_DFS
select RT_USING_DFS_ELMFAT
default n
endmenu
menu "On-chip Peripheral Drivers"
config BSP_USING_GPIO
bool "Enable GPIO"
select RT_USING_PIN
default y
2019-01-08 12:04:44 +08:00
menuconfig BSP_USING_UART
bool "Enable UART"
default y
select RT_USING_SERIAL
2019-01-08 12:04:44 +08:00
if BSP_USING_UART
config BSP_USING_UART1
bool "Enable UART1"
default y
config BSP_UART1_RX_USING_DMA
bool "Enable UART1 RX DMA"
depends on BSP_USING_UART1 && RT_SERIAL_USING_DMA
default n
2019-01-08 12:04:44 +08:00
config BSP_USING_UART2
bool "Enable UART2"
default n
config BSP_UART2_RX_USING_DMA
bool "Enable UART2 RX DMA"
depends on BSP_USING_UART2 && RT_SERIAL_USING_DMA
default n
config BSP_USING_UART3
bool "Enable UART3"
default n
config BSP_UART3_RX_USING_DMA
bool "Enable UART3 RX DMA"
depends on BSP_USING_UART3 && RT_SERIAL_USING_DMA
default n
endif
config BSP_USING_ON_CHIP_FLASH
bool "Enable on-chip FLASH"
default n
2019-01-08 12:04:44 +08:00
menuconfig BSP_USING_SPI
bool "Enable SPI BUS"
default n
select RT_USING_SPI
2019-01-08 12:04:44 +08:00
if BSP_USING_SPI
config BSP_USING_SPI1
bool "Enable SPI1 BUS"
default n
config BSP_SPI1_TX_USING_DMA
bool "Enable SPI1 TX DMA"
depends on BSP_USING_SPI1
default n
config BSP_SPI1_RX_USING_DMA
bool "Enable SPI1 RX DMA"
depends on BSP_USING_SPI1
select BSP_SPI1_TX_USING_DMA
default n
config BSP_USING_SPI2
bool "Enable SPI2 BUS"
default n
config BSP_SPI2_TX_USING_DMA
bool "Enable SPI2 TX DMA"
depends on BSP_USING_SPI2
default n
config BSP_SPI2_RX_USING_DMA
bool "Enable SPI2 RX DMA"
depends on BSP_USING_SPI2
select BSP_SPI2_TX_USING_DMA
default n
config BSP_USING_SPI5
bool "Enable SPI5 BUS"
default n
config BSP_SPI5_TX_USING_DMA
bool "Enable SPI5 TX DMA"
depends on BSP_USING_SPI5
default n
config BSP_SPI5_RX_USING_DMA
bool "Enable SPI5 RX DMA"
depends on BSP_USING_SPI5
select BSP_SPI5_TX_USING_DMA
default n
endif
menuconfig BSP_USING_I2C1
bool "Enable I2C1 BUS (software simulation)"
default n
select RT_USING_I2C
select RT_USING_I2C_BITOPS
select RT_USING_PIN
if BSP_USING_I2C1
comment "Notice: PH4 --> 116; PH5 --> 117"
config BSP_I2C1_SCL_PIN
int "I2C1 scl pin number"
range 1 176
default 116
config BSP_I2C1_SDA_PIN
int "I2C1 sda pin number"
range 1 176
default 117
endif
menuconfig BSP_USING_TIM
bool "Enable timer"
default n
select RT_USING_HWTIMER
if BSP_USING_TIM
config BSP_USING_TIM11
bool "Enable TIM11"
default n
config BSP_USING_TIM13
bool "Enable TIM13"
default n
config BSP_USING_TIM14
bool "Enable TIM14"
default n
endif
menuconfig BSP_USING_PWM
bool "Enable pwm"
default n
select RT_USING_PWM
if BSP_USING_PWM
menuconfig BSP_USING_PWM2
bool "Enable timer2 output pwm"
default n
if BSP_USING_PWM2
config BSP_USING_PWM2_CH4
bool "Enable PWM2 channel4"
default n
endif
endif
menuconfig BSP_USING_ADC
bool "Enable ADC"
default n
select RT_USING_ADC
if BSP_USING_ADC
config BSP_USING_ADC1
bool "Enable ADC1"
default n
endif
config BSP_USING_ONCHIP_RTC
bool "Enable RTC"
select RT_USING_RTC
select RT_USING_LIBC
default n
config BSP_USING_WDT
bool "Enable Watchdog Timer"
select RT_USING_WDT
default n
config BSP_USING_SDIO
bool "Enable SDIO"
select RT_USING_SDIO
select RT_USING_DFS
default n
config BSP_USING_FMC
bool
default n
endmenu
menu "Board extended module Drivers"
endmenu
endmenu