rt-thread/bsp/imxrt/imxrt1064-nxp-evk/board/Kconfig

menu "Hardware Drivers Config"


config BSP_USING_HYPERFLASH
    bool
    default n

config BSP_USING_4MFLASH
    bool
    default n

config SOC_MIMXRT1064DVL6A
    bool
    select SOC_MIMXRT1064_SERIES
    select BSP_USING_4MFLASH
    select RT_USING_COMPONENTS_INIT
    select RT_USING_USER_MAIN
    default y

menu "On-chip Peripheral Drivers"

    config BSP_USING_GPIO
        bool "Enable GPIO"
        select RT_USING_PIN
        default y

    menuconfig BSP_USING_LPUART
        bool "Enable UART"
        select RT_USING_SERIAL
        default y
        if BSP_USING_LPUART
            config BSP_USING_LPUART1
                bool "Enable LPUART1"
                default y
            config BSP_USING_LPUART2
                bool "Enable LPUART2"
                default n
            config BSP_USING_LPUART3
                bool "Enable LPUART3"
                default n
            config BSP_USING_LPUART4
                bool "Enable LPUART4"
                default n
            config BSP_USING_LPUART5
                bool "Enable LPUART5"
                default n
            config BSP_USING_LPUART6
                bool "Enable LPUART6"
                default n
            config BSP_USING_LPUART7
                bool "Enable LPUART7"
                default n
            config BSP_USING_LPUART8
                bool "Enable LPUART8"
                default n
        endif

    menuconfig BSP_USING_I2C
        bool "Enable I2C"
        select RT_USING_I2C
        default n
        if BSP_USING_I2C
            config BSP_USING_I2C1
                bool "Enable LPI2C1"
                default n
            config BSP_USING_I2C3
                bool "Enable LPI2C3"
                default n
            config BSP_USING_I2C4
                bool "Enable LPI2C4"
                default n
        endif

    menuconfig BSP_USING_LCD
        bool "Enable LCD"
        default n
        if BSP_USING_LCD
            config LCD_WIDTH
                int "width"
                default 480

            config LCD_HEIGHT
                int "height"
                default 272

            config LCD_HFP
                int "HFP"
                default 4
            config LCD_VFP
                int "VFP"
                default 4
            config LCD_HBP
                int "HBP"
                default 8
            config LCD_VBP
                int "VBP"
                default 2
            config LCD_HSW
                int "HSW"
                default 40
            config LCD_VSW
                int "VSW"
                default 10
            config LCD_BL_PIN
                int "Backlight ctrl pin"
                default 63
            config LCD_RST_PIN
                int "Reset pin"
                default 2
        endif

endmenu

menu "Onboard Peripheral Drivers"

    config BSP_USING_SDRAM
        bool "Enable SDRAM"
        default n

    menuconfig BSP_USING_ETH
    bool "Enable Ethernet"
    select RT_USING_NETDEV
    default n


    if BSP_USING_ETH
        config BSP_USING_PHY
            select RT_USING_PHY
            bool "Enable ethernet phy"
            default y

        if BSP_USING_PHY
            config PHY_DEVICE_ADDRESS
                int "Specify address of phy device"
                default 2

            config PHY_USING_KSZ8081
                bool "i.MX RT1064EVK uses ksz8081 phy"
                default y

            if PHY_USING_KSZ8081
                config PHY_RESET_PORT
                    int "indicate port of reset"
                    default 1

                config PHY_RESET_PIN
                    int "indicate pin of reset"
                    default 9

                config FSL_FEATURE_PHYKSZ8081_USE_RMII50M_MODE
                    bool "Enable the PHY ksz8081 RMII50M mode"
                    depends on PHY_USING_KSZ8081
                    default y
            endif

        endif
    endif
endmenu

menu "Board extended module Drivers"

endmenu

endmenu