rt-thread/bsp/ck802/libraries/common/usart/dw_usart.h

111 lines
4.9 KiB
C
Raw Normal View History

2018-06-05 14:36:29 +08:00
/*
* Copyright (C) 2017 C-SKY Microsystems Co., Ltd. All rights reserved.
*
* Licensed under the Apache License, Version 2.0 (the "License");
* you may not use this file except in compliance with the License.
* You may obtain a copy of the License at
*
* http://www.apache.org/licenses/LICENSE-2.0
*
* Unless required by applicable law or agreed to in writing, software
* distributed under the License is distributed on an "AS IS" BASIS,
* WITHOUT WARRANTIES OR CONDITIONS OF ANY KIND, either express or implied.
* See the License for the specific language governing permissions and
* limitations under the License.
*/
/******************************************************************************
* @file dw_usart.h
* @brief header file for usart driver
* @version V1.0
* @date 02. June 2017
******************************************************************************/
#ifndef __DW_USART_H
#define __DW_USART_H
#include <stdio.h>
#include "errno.h"
#include "soc.h"
#define BAUDRATE_DEFAULT 19200
#define UART_BUSY_TIMEOUT 1000000
#define UART_RECEIVE_TIMEOUT 1000
#define UART_TRANSMIT_TIMEOUT 1000
#define UART_MAX_FIFO 0x10
/* UART register bit definitions */
#define USR_UART_BUSY 0x01
#define USR_UART_TFE 0x04
#define USR_UART_RFNE 0x08
#define LSR_DATA_READY 0x01
#define LSR_THR_EMPTY 0x20
#define IER_RDA_INT_ENABLE 0x01
#define IER_THRE_INT_ENABLE 0x02
#define IIR_NO_ISQ_PEND 0x01
#define LCR_SET_DLAB 0x80 /* enable r/w DLR to set the baud rate */
#define LCR_PARITY_ENABLE 0x08 /* parity enabled */
#define LCR_PARITY_EVEN 0x10 /* Even parity enabled */
#define LCR_PARITY_ODD 0xef /* Odd parity enabled */
#define LCR_WORD_SIZE_5 0xfc /* the data length is 5 bits */
#define LCR_WORD_SIZE_6 0x01 /* the data length is 6 bits */
#define LCR_WORD_SIZE_7 0x02 /* the data length is 7 bits */
#define LCR_WORD_SIZE_8 0x03 /* the data length is 8 bits */
#define LCR_STOP_BIT1 0xfb /* 1 stop bit */
#define LCR_STOP_BIT2 0x04 /* 1.5 stop bit */
#define DW_LSR_PFE 0x80
#define DW_LSR_TEMT 0x40
#define DW_LSR_THRE 0x40
#define DW_LSR_BI 0x10
#define DW_LSR_FE 0x08
#define DW_LSR_PE 0x04
#define DW_LSR_OE 0x02
#define DW_LSR_DR 0x01
#define DW_LSR_TRANS_EMPTY 0x20
#define DW_FCR_FIFOE 0x01
#define DW_FCR_RFIFOR 0x02
#define DW_FCR_XFIFOR 0x04
#define DW_FCR_RT_FIFO_SINGLE 0x00 /* rcvr trigger 1 character in the FIFO */
#define DW_FCR_RT_FIFO_QUARTER 0x01 /* rcvr trigger FIFO 1/4 full */
#define DW_FCR_RT_FIFO_HALF 0x10 /* rcvr trigger FIFO 1/2 full */
#define DW_FCR_RT_FIFO_LESSTWO 0x11 /* rcvr trigger FIFO 2 less than full */
#define DW_FCR_TET_FIFO_EMPTY 0x00 /* tx empty trigger FIFO empty */
#define DW_FCR_TET_FIFO_TWO 0x01 /* tx empty trigger 2 characters in the FIFO */
#define DW_FCR_TET_FIFO_QUARTER 0x10 /* tx empty trigger FIFO 1/4 full */
#define DW_FCR_TET_FIFO_HALF 0x11 /* tx empty trigger FIFO 1/2 full*/
#define DW_IIR_THR_EMPTY 0x02 /* threshold empty */
#define DW_IIR_RECV_DATA 0x04 /* received data available */
typedef struct {
union {
__IM uint32_t RBR; /* Offset: 0x000 (R/ ) Receive buffer register */
__OM uint32_t THR; /* Offset: 0x000 ( /W) Transmission hold register */
__IOM uint32_t DLL; /* Offset: 0x000 (R/W) Clock frequency division low section register */
};
union {
__IOM uint32_t DLH; /* Offset: 0x004 (R/W) Clock frequency division high section register */
__IOM uint32_t IER; /* Offset: 0x004 (R/W) Interrupt enable register */
};
union {
__IM uint32_t IIR; /* Offset: 0x008 (R/ ) Interrupt indicia register */
__OM uint32_t FCR; /* Offset: 0x008 ( /W) FIFO control register */
};
__IOM uint32_t LCR; /* Offset: 0x00C (R/W) Transmission control register */
__IOM uint32_t MCR; /* Offset: 0x010 (R/W) Modem control register */
__IM uint32_t LSR; /* Offset: 0x014 (R/ ) Transmission state register */
__IM uint32_t MSR; /* Offset: 0x018 (R/ ) Modem state register */
uint32_t RESERVED1[21];
__IOM uint32_t FAR; /* Offset: 0x070 (R/W) FIFO accesss register */
__IM uint32_t TFR; /* Offset: 0x074 (R/ ) transmit FIFO read */
__OM uint32_t RFW; /* Offset: 0x078 ( /W) receive FIFO write */
__IM uint32_t USR; /* Offset: 0x07c (R/ ) UART state register */
__IM uint32_t TFL; /* Offset: 0x080 (R/ ) transmit FIFO level */
__IM uint32_t RFL; /* Offset: 0x084 (R/ ) receive FIFO level */
} dw_usart_reg_t;
#endif /* __DW_USART_H */