rt-thread/bsp/c28x/libraries/tms320f28379d/common/source/usb.c

3973 lines
129 KiB
C
Raw Normal View History

//###########################################################################
//
// FILE: usb.c
//
// TITLE: Driver for the USB Interface.
//
//###########################################################################
// $TI Release: F2837xD Support Library v3.05.00.00 $
// $Release Date: Tue Jun 26 03:15:23 CDT 2018 $
// $Copyright:
// Copyright (C) 2013-2018 Texas Instruments Incorporated - http://www.ti.com/
//
// Redistribution and use in source and binary forms, with or without
// modification, are permitted provided that the following conditions
// are met:
//
// Redistributions of source code must retain the above copyright
// notice, this list of conditions and the following disclaimer.
//
// Redistributions in binary form must reproduce the above copyright
// notice, this list of conditions and the following disclaimer in the
// documentation and/or other materials provided with the
// distribution.
//
// Neither the name of Texas Instruments Incorporated nor the names of
// its contributors may be used to endorse or promote products derived
// from this software without specific prior written permission.
//
// THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS
// "AS IS" AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT
// LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR
// A PARTICULAR PURPOSE ARE DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT
// OWNER OR CONTRIBUTORS BE LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL,
// SPECIAL, EXEMPLARY, OR CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT
// LIMITED TO, PROCUREMENT OF SUBSTITUTE GOODS OR SERVICES; LOSS OF USE,
// DATA, OR PROFITS; OR BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY
// THEORY OF LIABILITY, WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT
// (INCLUDING NEGLIGENCE OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE
// OF THIS SOFTWARE, EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
// $
//###########################################################################
//*****************************************************************************
//
//! \addtogroup usb_api
//! @{
//
//*****************************************************************************
#include <stdbool.h>
#include <stdint.h>
#include "inc/hw_ints.h"
#include "inc/hw_memmap.h"
#include "inc/hw_types.h"
#include "inc/hw_usb.h"
#include "driverlib/debug.h"
#include "driverlib/interrupt.h"
#include "driverlib/sysctl.h"
#include "usb.h"
//*****************************************************************************
//
// Amount to shift the RX interrupt sources by in the flags used in the
// interrupt calls.
//
//*****************************************************************************
#define USB_INTEP_RX_SHIFT 16
//*****************************************************************************
//
// Amount to shift the RX endpoint status sources by in the flags used in the
// calls.
//
//*****************************************************************************
#define USB_RX_EPSTATUS_SHIFT 16
//*****************************************************************************
//
// Converts from an endpoint specifier to the offset of the endpoint's
// control/status registers.
//
//*****************************************************************************
#define EP_OFFSET(Endpoint) (Endpoint - 0x10)
//*****************************************************************************
//
// Sets one of the indexed registers.
//
// \param ui32Base specifies the USB module base address.
// \param ui32Endpoint is the endpoint index to target for this write.
// \param ui32IndexedReg is the indexed register to write to.
// \param ui8Value is the value to write to the register.
//
// This function is used to access the indexed registers for each endpoint.
// The only registers that are indexed are the FIFO configuration registers,
// which are not used after configuration.
//
// \return None.
//
//*****************************************************************************
static void
_USBIndexWrite(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32IndexedReg, uint32_t ui32Value, uint32_t ui32Size)
{
uint32_t ui32Index;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == 0) || (ui32Endpoint == 1) || (ui32Endpoint == 2) ||
(ui32Endpoint == 3));
ASSERT((ui32Size == 1) || (ui32Size == 2));
//
// Save the old index in case it was in use.
//
ui32Index = HWREGB(ui32Base + USB_O_EPIDX);
//
// Set the index.
//
HWREGB(ui32Base + USB_O_EPIDX) = ui32Endpoint;
//
// Determine the size of the register value.
//
if(ui32Size == 1)
{
//
// Set the value.
//
HWREGB(ui32Base + ui32IndexedReg) = ui32Value;
}
else
{
//
// Set the value.
//
HWREGH(ui32Base + ui32IndexedReg) = ui32Value;
}
//
// Restore the old index in case it was in use.
//
HWREGB(ui32Base + USB_O_EPIDX) = ui32Index;
}
//*****************************************************************************
//
// Reads one of the indexed registers.
//
// \param ui32Base specifies the USB module base address.
// \param ui32Endpoint is the endpoint index to target for this write.
// \param ui32IndexedReg is the indexed register to write to.
//
// This function is used internally to access the indexed registers for each
// endpoint. The only registers that are indexed are the FIFO configuration
// registers, which are not used after configuration.
//
// \return The value in the register requested.
//
//*****************************************************************************
static uint32_t
_USBIndexRead(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32IndexedReg, uint32_t ui32Size)
{
uint8_t ui8Index;
uint8_t ui8Value;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == 0) || (ui32Endpoint == 1) || (ui32Endpoint == 2) ||
(ui32Endpoint == 3));
ASSERT((ui32Size == 1) || (ui32Size == 2));
//
// Save the old index in case it was in use.
//
ui8Index = HWREGB(ui32Base + USB_O_EPIDX);
//
// Set the index.
//
HWREGB(ui32Base + USB_O_EPIDX) = ui32Endpoint;
//
// Determine the size of the register value.
//
if(ui32Size == 1)
{
//
// Get the value.
//
ui8Value = HWREGB(ui32Base + ui32IndexedReg);
}
else
{
//
// Get the value.
//
ui8Value = HWREGH(ui32Base + ui32IndexedReg);
}
//
// Restore the old index in case it was in use.
//
HWREGB(ui32Base + USB_O_EPIDX) = ui8Index;
//
// Return the register's value.
//
return(ui8Value);
}
//*****************************************************************************
//
//! Puts the USB bus in a suspended state.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! When used in host mode, this function puts the USB bus in the suspended
//! state.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostSuspend(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Send the suspend signaling to the USB bus.
//
HWREGB(ui32Base + USB_O_POWER) |= USB_POWER_SUSPEND;
}
//*****************************************************************************
//
//! Handles the USB bus reset condition.
//!
//! \param ui32Base specifies the USB module base address.
//! \param bStart specifies whether to start or stop signaling reset on the USB
//! bus.
//!
//! When this function is called with the \e bStart parameter set to \b true,
//! this function causes the start of a reset condition on the USB bus.
//! The caller must then delay at least 20ms before calling this function
//! again with the \e bStart parameter set to \b false.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostReset(uint32_t ui32Base, bool bStart)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Send a reset signal to the bus.
//
if(bStart)
{
HWREGB(ui32Base + USB_O_POWER) |= USB_POWER_RESET;
}
else
{
HWREGB(ui32Base + USB_O_POWER) &= ~USB_POWER_RESET;
}
}
//*****************************************************************************
//
//! Handles the USB bus resume condition.
//!
//! \param ui32Base specifies the USB module base address.
//! \param bStart specifies if the USB controller is entering or leaving the
//! resume signaling state.
//!
//! When in device mode, this function brings the USB controller out of the
//! suspend state. This call must first be made with the \e bStart parameter
//! set to \b true to start resume signaling. The device application must
//! then delay at least 10ms but not more than 15ms before calling this
//! function with the \e bStart parameter set to \b false.
//!
//! When in host mode, this function signals devices to leave the suspend
//! state. This call must first be made with the \e bStart parameter set to
//! \b true to start resume signaling. The host application must then delay
//! at least 20ms before calling this function with the \e bStart parameter set
//! to \b false. This action causes the controller to complete the resume
//! signaling on the USB bus.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostResume(uint32_t ui32Base, bool bStart)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Send a resume signal to the bus.
//
if(bStart)
{
HWREGB(ui32Base + USB_O_POWER) |= USB_POWER_RESUME;
}
else
{
HWREGB(ui32Base + USB_O_POWER) &= ~USB_POWER_RESUME;
}
}
//*****************************************************************************
//
//! Returns the current speed of the USB device connected.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function returns the current speed of the USB bus in host mode.
//!
//! \b Example: Get the USB connection speed.
//!
//! \verbatim
//! //
//! // Get the connection speed of the device connected to the USB controller.
//! //
//! USBHostSpeedGet(USB0_BASE);
//! \endverbatim
//!
//! \note This function must only be called in host mode.
//!
//! \return Returns one of the following: \b USB_LOW_SPEED, \b USB_FULL_SPEED,
//! or \b USB_UNDEF_SPEED.
//
//*****************************************************************************
uint32_t
USBHostSpeedGet(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// If the Full Speed device bit is set, then this is a full speed device.
//
if(HWREGB(ui32Base + USB_O_DEVCTL) & USB_DEVCTL_FSDEV)
{
return(USB_FULL_SPEED);
}
//
// If the Low Speed device bit is set, then this is a low speed device.
//
if(HWREGB(ui32Base + USB_O_DEVCTL) & USB_DEVCTL_LSDEV)
{
return(USB_LOW_SPEED);
}
//
// The device speed is not known.
//
return(USB_UNDEF_SPEED);
}
//*****************************************************************************
//
//! Disables control interrupts on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Flags specifies which control interrupts to disable.
//!
//! This function disables the control interrupts for the USB controller
//! specified by the \e ui32Base parameter. The \e ui32Flags parameter
//! specifies which control interrupts to disable. The flags passed in the
//! \e ui32Flags parameters must be the definitions that start with
//! \b USB_INTCTRL_* and not any other \b USB_INT flags.
//!
//! \return None.
//
//*****************************************************************************
void
USBIntDisableControl(uint32_t ui32Base, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Flags & ~(USB_INTCTRL_ALL)) == 0);
//
// If any general interrupts were disabled then write the general interrupt
// settings out to the hardware.
//
if(ui32Flags & USB_INTCTRL_STATUS)
{
HWREGB(ui32Base + USB_O_IE) &= ~(ui32Flags & USB_INTCTRL_STATUS);
}
//
// Disable the power fault interrupt.
//
if(ui32Flags & USB_INTCTRL_POWER_FAULT)
{
HWREG(ui32Base + USB_O_EPCIM) = 0;
}
//
// Disable the ID pin detect interrupt.
//
if(ui32Flags & USB_INTCTRL_MODE_DETECT)
{
HWREG(USB0_BASE + USB_O_IDVIM) = 0;
}
}
//*****************************************************************************
//
//! Enables control interrupts on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Flags specifies which control interrupts to enable.
//!
//! This function enables the control interrupts for the USB controller
//! specified by the \e ui32Base parameter. The \e ui32Flags parameter
//! specifies which control interrupts to enable. The flags passed in the
//! \e ui32Flags parameters must be the definitions that start with
//! \b USB_INTCTRL_* and not any other \b USB_INT flags.
//!
//! \return None.
//
//*****************************************************************************
void
USBIntEnableControl(uint32_t ui32Base, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Flags & (~USB_INTCTRL_ALL)) == 0);
//
// If any general interrupts were enabled, then write the general
// interrupt settings out to the hardware.
//
if(ui32Flags & USB_INTCTRL_STATUS)
{
HWREGB(ui32Base + USB_O_IE) |= ui32Flags;
}
//
// Enable the power fault interrupt.
//
if(ui32Flags & USB_INTCTRL_POWER_FAULT)
{
HWREG(ui32Base + USB_O_EPCIM) = USB_EPCIM_PF;
}
//
// Enable the ID pin detect interrupt.
//
if(ui32Flags & USB_INTCTRL_MODE_DETECT)
{
HWREG(USB0_BASE + USB_O_IDVIM) = USB_IDVIM_ID;
}
}
//*****************************************************************************
//
//! Returns the control interrupt status on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32IntStatusEP is a pointer to the variable which holds the
//! endpoint interrupt status from RXIS And TXIS.
//!
//! This function reads control interrupt status for a USB controller. This
//! call returns the current status for control interrupts only, the endpoint
//! interrupt status is retrieved by calling USBIntStatusEndpoint(). The bit
//! values returned are compared against the \b USB_INTCTRL_* values.
//!
//! The following are the meanings of all \b USB_INCTRL_ flags and the modes
//! for which they are valid. These values apply to any calls to
//! USBIntStatusControl(), USBIntEnableControl(), and USBIntDisableControl().
//! Some of these flags are only valid in the following modes as indicated in
//! the parentheses: Host, Device, and OTG.
//!
//! - \b USB_INTCTRL_ALL - A full mask of all control interrupt sources.
//! - \b USB_INTCTRL_VBUS_ERR - A VBUS error has occurred (Host Only).
//! - \b USB_INTCTRL_SESSION - Session Start Detected on A-side of cable
//! (OTG Only).
//! - \b USB_INTCTRL_SESSION_END - Session End Detected (Device Only)
//! - \b USB_INTCTRL_DISCONNECT - Device Disconnect Detected (Host Only)
//! - \b USB_INTCTRL_CONNECT - Device Connect Detected (Host Only)
//! - \b USB_INTCTRL_SOF - Start of Frame Detected.
//! - \b USB_INTCTRL_BABBLE - USB controller detected a device signaling past
//! the end of a frame (Host Only)
//! - \b USB_INTCTRL_RESET - Reset signaling detected by device (Device Only)
//! - \b USB_INTCTRL_RESUME - Resume signaling detected.
//! - \b USB_INTCTRL_SUSPEND - Suspend signaling detected by device (Device
//! Only)
//! - \b USB_INTCTRL_MODE_DETECT - OTG cable mode detection has completed
//! (OTG Only)
//! - \b USB_INTCTRL_POWER_FAULT - Power Fault detected (Host Only)
//!
//! \note This call clears the source of all of the control status interrupts.
//!
//! \return Returns the status of the control interrupts for a USB controller.
//! This is the value of USBIS.
//
//*****************************************************************************
uint32_t
USBIntStatus(uint32_t ui32Base, uint32_t *pui32IntStatusEP)
{
uint32_t ui32Status = 0;
*pui32IntStatusEP = 0;
uint32_t usbis = 0;
uint32_t rxis = 0;
uint32_t txis = 0;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Do-While to make sure that all status registers are cleared before continuing.
// This eliminates the race condition which can cause the USB interrupt to stay high
// and never get triggered again.
//
do
{
// Get the general interrupt status.
usbis = (uint32_t)HWREGB(ui32Base + USB_O_IS);
// Get the transmit interrupt status.
txis = (uint32_t)HWREGH(ui32Base + USB_O_TXIS);
// Get the receive interrupt status.
rxis = (uint32_t)HWREGH(ui32Base + USB_O_RXIS);
// Get the general interrupt status, these bits go into the upper 8 bits
// of the returned value.
ui32Status |= usbis;
// Get the transmit interrupt status.
*pui32IntStatusEP |= txis;
// Get the receive interrupt status, these bits go into the second byte of
// the returned value.
*pui32IntStatusEP |= ((uint32_t)rxis << USB_INTEP_RX_SHIFT);
} while(usbis != 0x0000 || txis != 0x0000 || rxis != 0x0000);
//
// Add the power fault status.
//
if(HWREG(ui32Base + USB_O_EPCISC) & USB_EPCISC_PF)
{
//
// Indicate a power fault was detected.
//
ui32Status |= USB_INTCTRL_POWER_FAULT;
//
// Clear the power fault interrupt.
//
HWREGB(ui32Base + USB_O_EPCISC) |= USB_EPCISC_PF;
}
if(HWREG(USB0_BASE + USB_O_IDVISC) & USB_IDVRIS_ID)
{
//
// Indicate an id detection.
//
ui32Status |= USB_INTCTRL_MODE_DETECT;
//
// Clear the id detection interrupt.
//
HWREG(USB0_BASE + USB_O_IDVISC) |= USB_IDVRIS_ID;
}
//
// Return the combined interrupt status.
//
return(ui32Status);
}
//*****************************************************************************
//
//! Returns the control interrupt status on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function reads control interrupt status for a USB controller. This
//! call returns the current status for control interrupts only, the endpoint
//! interrupt status is retrieved by calling USBIntStatusEndpoint(). The bit
//! values returned are compared against the \b USB_INTCTRL_* values.
//!
//! The following are the meanings of all \b USB_INCTRL_ flags and the modes
//! for which they are valid. These values apply to any calls to
//! USBIntStatusControl(), USBIntEnableControl(), and USBIntDisableControl().
//! Some of these flags are only valid in the following modes as indicated in
//! the parentheses: Host, Device, and OTG.
//!
//! - \b USB_INTCTRL_ALL - A full mask of all control interrupt sources.
//! - \b USB_INTCTRL_VBUS_ERR - A VBUS error has occurred (Host Only).
//! - \b USB_INTCTRL_SESSION - Session Start Detected on A-side of cable
//! (OTG Only).
//! - \b USB_INTCTRL_SESSION_END - Session End Detected (Device Only)
//! - \b USB_INTCTRL_DISCONNECT - Device Disconnect Detected (Host Only)
//! - \b USB_INTCTRL_CONNECT - Device Connect Detected (Host Only)
//! - \b USB_INTCTRL_SOF - Start of Frame Detected.
//! - \b USB_INTCTRL_BABBLE - USB controller detected a device signaling past
//! the end of a frame (Host Only)
//! - \b USB_INTCTRL_RESET - Reset signaling detected by device (Device Only)
//! - \b USB_INTCTRL_RESUME - Resume signaling detected.
//! - \b USB_INTCTRL_SUSPEND - Suspend signaling detected by device (Device
//! Only)
//! - \b USB_INTCTRL_MODE_DETECT - OTG cable mode detection has completed
//! (OTG Only)
//! - \b USB_INTCTRL_POWER_FAULT - Power Fault detected (Host Only)
//!
//! \note This call clears the source of all of the control status interrupts.
//!
//! \return Returns the status of the control interrupts for a USB controller.
//
//*****************************************************************************
uint32_t
USBIntStatusControl(uint32_t ui32Base)
{
uint32_t ui32Status;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Get the general interrupt status, these bits go into the upper 8 bits
// of the returned value.
//
ui32Status = HWREGB(ui32Base + USB_O_IS);
//*ui32EPStatus = USBIntStatusEndpoint(ui32Base);
//
// Add the power fault status.
//
if(HWREG(ui32Base + USB_O_EPCISC) & USB_EPCISC_PF)
{
//
// Indicate a power fault was detected.
//
ui32Status |= USB_INTCTRL_POWER_FAULT;
//
// Clear the power fault interrupt.
//
HWREGB(ui32Base + USB_O_EPCISC) |= USB_EPCISC_PF;
}
if(HWREG(USB0_BASE + USB_O_IDVISC) & USB_IDVRIS_ID)
{
//
// Indicate an id detection.
//
ui32Status |= USB_INTCTRL_MODE_DETECT;
//
// Clear the id detection interrupt.
//
HWREG(USB0_BASE + USB_O_IDVISC) |= USB_IDVRIS_ID;
}
//
// Return the combined interrupt status.
//
return(ui32Status);
}
//*****************************************************************************
//
//! Disables endpoint interrupts on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Flags specifies which endpoint interrupts to disable.
//!
//! This function disables endpoint interrupts for the USB controller specified
//! by the \e ui32Base parameter. The \e ui32Flags parameter specifies which
//! endpoint interrupts to disable. The flags passed in the \e ui32Flags
//! parameters must be the definitions that start with \b USB_INTEP_* and not
//! any other \b USB_INT flags.
//!
//! \return None.
//
//*****************************************************************************
void
USBIntDisableEndpoint(uint32_t ui32Base, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// If any transmit interrupts were disabled, then write the transmit
// interrupt settings out to the hardware.
//
HWREGH(ui32Base + USB_O_TXIE) &=
~(ui32Flags & (USB_INTEP_HOST_OUT | USB_INTEP_DEV_IN | USB_INTEP_0));
//
// If any receive interrupts were disabled, then write the receive
// interrupt settings out to the hardware.
//
HWREGH(ui32Base + USB_O_RXIE) &=
~((ui32Flags & (USB_INTEP_HOST_IN | USB_INTEP_DEV_OUT)) >>
USB_INTEP_RX_SHIFT);
}
//*****************************************************************************
//
//! Enables endpoint interrupts on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Flags specifies which endpoint interrupts to enable.
//!
//! This function enables endpoint interrupts for the USB controller specified
//! by the \e ui32Base parameter. The \e ui32Flags parameter specifies which
//! endpoint interrupts to enable. The flags passed in the \e ui32Flags
//! parameters must be the definitions that start with \b USB_INTEP_* and not
//! any other \b USB_INT flags.
//!
//! \return None.
//
//*****************************************************************************
void
USBIntEnableEndpoint(uint32_t ui32Base, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Enable any transmit endpoint interrupts.
//
HWREGH(ui32Base + USB_O_TXIE) |=
ui32Flags & (USB_INTEP_HOST_OUT | USB_INTEP_DEV_IN | USB_INTEP_0);
//
// Enable any receive endpoint interrupts.
//
HWREGH(ui32Base + USB_O_RXIE) |=
((ui32Flags & (USB_INTEP_HOST_IN | USB_INTEP_DEV_OUT)) >>
USB_INTEP_RX_SHIFT);
}
//*****************************************************************************
//
//! Returns the endpoint interrupt status on a given USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function reads endpoint interrupt status for a USB controller. This
//! call returns the current status for endpoint interrupts only, the control
//! interrupt status is retrieved by calling USBIntStatusControl(). The bit
//! values returned are compared against the \b USB_INTEP_* values.
//! These values are grouped into classes for \b USB_INTEP_HOST_* and
//! \b USB_INTEP_DEV_* values to handle both host and device modes with all
//! endpoints.
//!
//! \note This call clears the source of all of the endpoint interrupts.
//!
//! \return Returns the status of the endpoint interrupts for a USB controller.
//
//*****************************************************************************
uint32_t
USBIntStatusEndpoint(uint32_t ui32Base)
{
uint32_t ui32Status;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Get the transmit interrupt status.
//
ui32Status = HWREGH(ui32Base + USB_O_TXIS);
ui32Status |= ((uint32_t)HWREGH(ui32Base + USB_O_RXIS) << USB_INTEP_RX_SHIFT);
//
// Return the combined interrupt status.
//
return(ui32Status);
}
//*****************************************************************************
//
//! Returns the interrupt number for a given USB module.
//!
//! \param ui32Base is the base address of the USB module.
//!
//! This function returns the interrupt number for the USB module with the base
//! address passed in the \e ui32Base parameter.
//!
//! \return Returns the USB interrupt number or 0 if the interrupt does not
//! exist.
//
//*****************************************************************************
static uint32_t
_USBIntNumberGet(uint32_t ui32Base)
{
return(INT_USB0);
}
//*****************************************************************************
//
//! Registers an interrupt handler for the USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//! \param pfnHandler is a pointer to the function to be called when a USB
//! interrupt occurs.
//!
//! This function registers the handler to be called when a USB interrupt
//! occurs and enables the global USB interrupt in the interrupt controller.
//! The specific desired USB interrupts must be enabled via a separate call to
//! USBIntEnable(). It is the interrupt handler's responsibility to clear the
//! interrupt sources via calls to USBIntStatusControl() and
//! USBIntStatusEndpoint().
//!
//! \sa IntRegister() for important information about registering interrupt
//! handlers.
//!
//! \return None.
//
//*****************************************************************************
void
USBIntRegister(uint32_t ui32Base, void (*pfnHandler)(void))
{
uint32_t ui32Int;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ui32Int = _USBIntNumberGet(ui32Base);
ASSERT(ui32Int != 0);
//
// Register the interrupt handler.
//
IntRegister(ui32Int, pfnHandler);
//
// Enable the USB interrupt.
//
IntEnable(ui32Int);
}
//*****************************************************************************
//
//! Unregisters an interrupt handler for the USB controller.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function unregisters the interrupt handler. This function also
//! disables the USB interrupt in the interrupt controller.
//!
//! \sa IntRegister() for important information about registering or
//! unregistering interrupt handlers.
//!
//! \return None.
//
//*****************************************************************************
void
USBIntUnregister(uint32_t ui32Base)
{
uint32_t ui32Int;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ui32Int = _USBIntNumberGet(ui32Base);
ASSERT(ui32Int != 0);
//
// Disable the USB interrupt.
//
IntDisable(ui32Int);
//
// Unregister the interrupt handler.
//
IntUnregister(ui32Int);
}
//*****************************************************************************
//
//! Returns the current status of an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//!
//! This function returns the status of a given endpoint. If any of these
//! status bits must be cleared, then the USBDevEndpointStatusClear() or the
//! USBHostEndpointStatusClear() functions must be called.
//!
//! The following are the status flags for host mode:
//!
//! - \b USB_HOST_IN_PID_ERROR - PID error on the given endpoint.
//! - \b USB_HOST_IN_NOT_COMP - The device failed to respond to an IN request.
//! - \b USB_HOST_IN_STALL - A stall was received on an IN endpoint.
//! - \b USB_HOST_IN_DATA_ERROR - There was a CRC or bit-stuff error on an IN
//! endpoint in Isochronous mode.
//! - \b USB_HOST_IN_NAK_TO - NAKs received on this IN endpoint for more than
//! the specified timeout period.
//! - \b USB_HOST_IN_ERROR - Failed to communicate with a device using this IN
//! endpoint.
//! - \b USB_HOST_IN_FIFO_FULL - This IN endpoint's FIFO is full.
//! - \b USB_HOST_IN_PKTRDY - Data packet ready on this IN endpoint.
//! - \b USB_HOST_OUT_NAK_TO - NAKs received on this OUT endpoint for more than
//! the specified timeout period.
//! - \b USB_HOST_OUT_NOT_COMP - The device failed to respond to an OUT
//! request.
//! - \b USB_HOST_OUT_STALL - A stall was received on this OUT endpoint.
//! - \b USB_HOST_OUT_ERROR - Failed to communicate with a device using this
//! OUT endpoint.
//! - \b USB_HOST_OUT_FIFO_NE - This endpoint's OUT FIFO is not empty.
//! - \b USB_HOST_OUT_PKTPEND - The data transfer on this OUT endpoint has not
//! completed.
//! - \b USB_HOST_EP0_NAK_TO - NAKs received on endpoint zero for more than the
//! specified timeout period.
//! - \b USB_HOST_EP0_ERROR - The device failed to respond to a request on
//! endpoint zero.
//! - \b USB_HOST_EP0_IN_STALL - A stall was received on endpoint zero for an
//! IN transaction.
//! - \b USB_HOST_EP0_IN_PKTRDY - Data packet ready on endpoint zero for an IN
//! transaction.
//!
//! The following are the status flags for device mode:
//!
//! - \b USB_DEV_OUT_SENT_STALL - A stall was sent on this OUT endpoint.
//! - \b USB_DEV_OUT_DATA_ERROR - There was a CRC or bit-stuff error on an OUT
//! endpoint.
//! - \b USB_DEV_OUT_OVERRUN - An OUT packet was not loaded due to a full FIFO.
//! - \b USB_DEV_OUT_FIFO_FULL - The OUT endpoint's FIFO is full.
//! - \b USB_DEV_OUT_PKTRDY - There is a data packet ready in the OUT
//! endpoint's FIFO.
//! - \b USB_DEV_IN_NOT_COMP - A larger packet was split up, more data to come.
//! - \b USB_DEV_IN_SENT_STALL - A stall was sent on this IN endpoint.
//! - \b USB_DEV_IN_UNDERRUN - Data was requested on the IN endpoint and no
//! data was ready.
//! - \b USB_DEV_IN_FIFO_NE - The IN endpoint's FIFO is not empty.
//! - \b USB_DEV_IN_PKTPEND - The data transfer on this IN endpoint has not
//! completed.
//! - \b USB_DEV_EP0_SETUP_END - A control transaction ended before Data End
//! condition was sent.
//! - \b USB_DEV_EP0_SENT_STALL - A stall was sent on endpoint zero.
//! - \b USB_DEV_EP0_IN_PKTPEND - The data transfer on endpoint zero has not
//! completed.
//! - \b USB_DEV_EP0_OUT_PKTRDY - There is a data packet ready in endpoint
//! zero's OUT FIFO.
//!
//! \return The current status flags for the endpoint depending on mode.
//
//*****************************************************************************
uint32_t
USBEndpointStatus(uint32_t ui32Base, uint32_t ui32Endpoint)
{
uint32_t ui32Status;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Get the TX portion of the endpoint status.
//
ui32Status = HWREGH(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRL1);
//
// Get the RX portion of the endpoint status.
//
ui32Status |=
(((uint32_t)HWREGH(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRL1)) <<
USB_RX_EPSTATUS_SHIFT);
//
// Return the endpoint status.
//
return(ui32Status);
}
//*****************************************************************************
//
//! Clears the status bits in this endpoint in host mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags are the status bits that are cleared.
//!
//! This function clears the status of any bits that are passed in the
//! \e ui32Flags parameter. The \e ui32Flags parameter can take the value
//! returned from the USBEndpointStatus() call.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostEndpointStatusClear(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Clear the specified flags for the endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
HWREGB(ui32Base + USB_O_CSRL0) &= ~ui32Flags;
}
else
{
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~ui32Flags;
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~(ui32Flags >> USB_RX_EPSTATUS_SHIFT);
}
}
//*****************************************************************************
//
//! Clears the status bits in this endpoint in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags are the status bits that are cleared.
//!
//! This function clears the status of any bits that are passed in the
//! \e ui32Flags parameter. The \e ui32Flags parameter can take the value
//! returned from the USBEndpointStatus() call.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevEndpointStatusClear(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// If this is endpoint 0, then the bits have different meaning and map
// into the TX memory location.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Set the Serviced RxPktRdy bit to clear the RxPktRdy.
//
if(ui32Flags & USB_DEV_EP0_OUT_PKTRDY)
{
HWREGB(ui32Base + USB_O_CSRL0) |= USB_CSRL0_RXRDYC;
}
//
// Set the serviced Setup End bit to clear the SetupEnd status.
//
if(ui32Flags & USB_DEV_EP0_SETUP_END)
{
HWREGB(ui32Base + USB_O_CSRL0) |= USB_CSRL0_SETENDC;
}
//
// Clear the Sent Stall status flag.
//
if(ui32Flags & USB_DEV_EP0_SENT_STALL)
{
HWREGB(ui32Base + USB_O_CSRL0) &= ~(USB_DEV_EP0_SENT_STALL);
}
}
else
{
//
// Clear out any TX flags that were passed in. Only
// USB_DEV_TX_SENT_STALL and USB_DEV_TX_UNDERRUN must be cleared.
//
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~(ui32Flags & (USB_DEV_TX_SENT_STALL | USB_DEV_TX_UNDERRUN));
//
// Clear out valid RX flags that were passed in. Only
// USB_DEV_RX_SENT_STALL, USB_DEV_RX_DATA_ERROR, and USB_DEV_RX_OVERRUN
// must be cleared.
//
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~((ui32Flags & (USB_DEV_RX_SENT_STALL | USB_DEV_RX_DATA_ERROR |
USB_DEV_RX_OVERRUN)) >> USB_RX_EPSTATUS_SHIFT);
}
}
//*****************************************************************************
//
//! Sets the value data toggle on an endpoint in host mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint specifies the endpoint to reset the data toggle.
//! \param bDataToggle specifies whether to set the state to DATA0 or DATA1.
//! \param ui32Flags specifies whether to set the IN or OUT endpoint.
//!
//! This function is used to force the state of the data toggle in host mode.
//! If the value passed in the \e bDataToggle parameter is \b false, then the
//! data toggle is set to the DATA0 state, and if it is \b true it is set to
//! the DATA1 state. The \e ui32Flags parameter can be \b USB_EP_HOST_IN or
//! \b USB_EP_HOST_OUT to access the desired portion of this endpoint. The
//! \e ui32Flags parameter is ignored for endpoint zero.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostEndpointDataToggle(uint32_t ui32Base, uint32_t ui32Endpoint,
bool bDataToggle, uint32_t ui32Flags)
{
uint32_t ui32DataToggle;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// The data toggle defaults to DATA0.
//
ui32DataToggle = 0;
//
// See if the data toggle must be set to DATA1.
//
if(bDataToggle)
{
//
// Select the data toggle bit based on the endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
ui32DataToggle = USB_CSRH0_DT;
}
else if(ui32Flags == USB_EP_HOST_IN)
{
ui32DataToggle = USB_RXCSRH1_DT;
}
else
{
ui32DataToggle = USB_TXCSRH1_DT;
}
}
//
// Set the data toggle based on the endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Set the write enable and the bit value for endpoint zero.
//
HWREGB(ui32Base + USB_O_CSRH0) =
((HWREGB(ui32Base + USB_O_CSRH0) &
~(USB_CSRH0_DTWE | USB_CSRH0_DT)) |
(ui32DataToggle | USB_CSRH0_DTWE));
}
else if(ui32Flags == USB_EP_HOST_IN)
{
//
// Set the Write enable and the bit value for an IN endpoint.
//
HWREGB(ui32Base + USB_O_RXCSRH1 + EP_OFFSET(ui32Endpoint)) =
((HWREGB(ui32Base + USB_O_RXCSRH1 + EP_OFFSET(ui32Endpoint)) &
~(USB_RXCSRH1_DTWE | USB_RXCSRH1_DT)) |
(ui32DataToggle | USB_RXCSRH1_DTWE));
}
else
{
//
// Set the Write enable and the bit value for an OUT endpoint.
//
HWREGB(ui32Base + USB_O_TXCSRH1 + EP_OFFSET(ui32Endpoint)) =
((HWREGB(ui32Base + USB_O_TXCSRH1 + EP_OFFSET(ui32Endpoint)) &
~(USB_TXCSRH1_DTWE | USB_TXCSRH1_DT)) |
(ui32DataToggle | USB_TXCSRH1_DTWE));
}
}
//*****************************************************************************
//
//! Sets the data toggle on an endpoint to zero.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint specifies the endpoint to reset the data toggle.
//! \param ui32Flags specifies whether to access the IN or OUT endpoint.
//!
//! This function causes the USB controller to clear the data toggle for an
//! endpoint. This call is not valid for endpoint zero and can be made with
//! host or device controllers.
//!
//! The \e ui32Flags parameter must be one of \b USB_EP_HOST_OUT,
//! \b USB_EP_HOST_IN, \b USB_EP_DEV_OUT, or \b USB_EP_DEV_IN.
//!
//! \return None.
//
//*****************************************************************************
void
USBEndpointDataToggleClear(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_1) || (ui32Endpoint == USB_EP_2) ||
(ui32Endpoint == USB_EP_3) || (ui32Endpoint == USB_EP_4) ||
(ui32Endpoint == USB_EP_5) || (ui32Endpoint == USB_EP_6) ||
(ui32Endpoint == USB_EP_7));
//
// See if the transmit or receive data toggle must be cleared.
//
if(ui32Flags & (USB_EP_HOST_OUT | USB_EP_DEV_IN))
{
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_TXCSRL1_CLRDT;
}
else
{
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_RXCSRL1_CLRDT;
}
}
//*****************************************************************************
//
//! Stalls the specified endpoint in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint specifies the endpoint to stall.
//! \param ui32Flags specifies whether to stall the IN or OUT endpoint.
//!
//! This function causes the endpoint number passed in to go into a stall
//! condition. If the \e ui32Flags parameter is \b USB_EP_DEV_IN, then the
//! stall is issued on the IN portion of this endpoint. If the \e ui32Flags
//! parameter is \b USB_EP_DEV_OUT, then the stall is issued on the OUT portion
//! of this endpoint.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevEndpointStall(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Flags & ~(USB_EP_DEV_IN | USB_EP_DEV_OUT)) == 0);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Determine how to stall this endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Perform a stall on endpoint zero.
//
HWREGB(ui32Base + USB_O_CSRL0) |= USB_CSRL0_STALL | USB_CSRL0_RXRDYC;
}
else if(ui32Flags == USB_EP_DEV_IN)
{
//
// Perform a stall on an IN endpoint.
//
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_TXCSRL1_STALL;
}
else
{
//
// Perform a stall on an OUT endpoint.
//
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_RXCSRL1_STALL;
}
}
//*****************************************************************************
//
//! Clears the stall condition on the specified endpoint in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint specifies which endpoint to remove the stall condition.
//! \param ui32Flags specifies whether to remove the stall condition from the
//! IN or the OUT portion of this endpoint.
//!
//! This function causes the endpoint number passed in to exit the stall
//! condition. If the \e ui32Flags parameter is \b USB_EP_DEV_IN, then the
//! stall is cleared on the IN portion of this endpoint. If the \e ui32Flags
//! parameter is \b USB_EP_DEV_OUT, then the stall is cleared on the OUT
//! portion of this endpoint.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevEndpointStallClear(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
ASSERT((ui32Flags & ~(USB_EP_DEV_IN | USB_EP_DEV_OUT)) == 0);
//
// Determine how to clear the stall on this endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Clear the stall on endpoint zero.
//
HWREGB(ui32Base + USB_O_CSRL0) &= ~USB_CSRL0_STALLED;
}
else if(ui32Flags == USB_EP_DEV_IN)
{
//
// Clear the stall on an IN endpoint.
//
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~(USB_TXCSRL1_STALL | USB_TXCSRL1_STALLED);
//
// Reset the data toggle.
//
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_TXCSRL1_CLRDT;
}
else
{
//
// Clear the stall on an OUT endpoint.
//
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~(USB_RXCSRL1_STALL | USB_RXCSRL1_STALLED);
//
// Reset the data toggle.
//
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_RXCSRL1_CLRDT;
}
}
//*****************************************************************************
//
//! Connects the USB controller to the bus in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function causes the soft connect feature of the USB controller to
//! be enabled. Call USBDevDisconnect() to remove the USB device from the bus.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevConnect(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Enable connection to the USB bus.
//
HWREGB(ui32Base + USB_O_POWER) |= USB_POWER_SOFTCONN;
}
//*****************************************************************************
//
//! Removes the USB controller from the bus in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function causes the soft connect feature of the USB controller to
//! remove the device from the USB bus. A call to USBDevConnect() is needed to
//! reconnect to the bus.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevDisconnect(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Disable connection to the USB bus.
//
HWREGB(ui32Base + USB_O_POWER) &= (~USB_POWER_SOFTCONN);
}
//*****************************************************************************
//
//! Sets the address in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Address is the address to use for a device.
//!
//! This function configures the device address on the USB bus. This address
//! was likely received via a SET ADDRESS command from the host controller.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevAddrSet(uint32_t ui32Base, uint32_t ui32Address)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Set the function address in the correct location.
//
HWREGB(ui32Base + USB_O_FADDR) = (uint8_t)ui32Address;
}
//*****************************************************************************
//
//! Returns the current device address in device mode.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function returns the current device address. This address was set
//! by a call to USBDevAddrSet().
//!
//! \note This function must only be called in device mode.
//!
//! \return The current device address.
//
//*****************************************************************************
uint32_t
USBDevAddrGet(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Return the function address.
//
return(HWREGB(ui32Base + USB_O_FADDR));
}
//*****************************************************************************
//
//! Sets the base configuration for a host endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32MaxPayload is the maximum payload for this endpoint.
//! \param ui32NAKPollInterval is the either the NAK timeout limit or the
//! polling interval, depending on the type of endpoint.
//! \param ui32TargetEndpoint is the endpoint that the host endpoint is
//! targeting.
//! \param ui32Flags are used to configure other endpoint settings.
//!
//! This function sets the basic configuration for the transmit or receive
//! portion of an endpoint in host mode. The \e ui32Flags parameter determines
//! some of the configuration while the other parameters provide the rest. The
//! \e ui32Flags parameter determines whether this is an IN endpoint
//! (\b USB_EP_HOST_IN or \b USB_EP_DEV_IN) or an OUT endpoint
//! (\b USB_EP_HOST_OUT or \b USB_EP_DEV_OUT), whether this is a Full speed
//! endpoint (\b USB_EP_SPEED_FULL) or a Low speed endpoint
//! (\b USB_EP_SPEED_LOW).
//!
//! The \b USB_EP_MODE_ flags control the type of the endpoint.
//! - \b USB_EP_MODE_CTRL is a control endpoint.
//! - \b USB_EP_MODE_ISOC is an isochronous endpoint.
//! - \b USB_EP_MODE_BULK is a bulk endpoint.
//! - \b USB_EP_MODE_INT is an interrupt endpoint.
//!
//! The \e ui32NAKPollInterval parameter has different meanings based on the
//! \b USB_EP_MODE value and whether or not this call is being made for
//! endpoint zero or another endpoint. For endpoint zero or any Bulk
//! endpoints, this value always indicates the number of frames to allow a
//! device to NAK before considering it a timeout. If this endpoint is an
//! isochronous or interrupt endpoint, this value is the polling interval for
//! this endpoint.
//!
//! For interrupt endpoints, the polling interval is the number of frames
//! between interrupt IN requests to an endpoint and has a range of 1 to 255.
//! For isochronous endpoints this value represents a polling interval of
//! 2 ^ (\e ui32NAKPollInterval - 1) frames. When used as a NAK timeout, the
//! \e ui32NAKPollInterval value specifies 2 ^ (\e ui32NAKPollInterval - 1)
//! frames before issuing a time out.
//!
//! There are two special time out values that can be specified when setting
//! the \e ui32NAKPollInterval value. The first is \b MAX_NAK_LIMIT, which is
//! the maximum value that can be passed in this variable. The other is
//! \b DISABLE_NAK_LIMIT, which indicates that there is no limit on the
//! number of NAKs.
//!
//! The \b USB_EP_DMA_MODE_ flags enable the type of DMA used to access the
//! endpoint's data FIFOs. The choice of the DMA mode depends on how the DMA
//! controller is configured and how it is being used. See the ``Using USB
//! with the uDMA Controller'' section for more information on DMA
//! configuration.
//!
//! When configuring the OUT portion of an endpoint, the \b USB_EP_AUTO_SET bit
//! is specified to cause the transmission of data on the USB bus to start
//! as soon as the number of bytes specified by \e ui32MaxPayload has been
//! written into the OUT FIFO for this endpoint.
//!
//! When configuring the IN portion of an endpoint, the \b USB_EP_AUTO_REQUEST
//! bit can be specified to trigger the request for more data once the FIFO has
//! been drained enough to fit \e ui32MaxPayload bytes. The
//! \b USB_EP_AUTO_CLEAR bit can be used to clear the data packet ready flag
//! automatically once the data has been read from the FIFO. If this option is
//! not used, this flag must be manually cleared via a call to
//! USBDevEndpointStatusClear() or USBHostEndpointStatusClear().
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostEndpointConfig(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32MaxPayload, uint32_t ui32NAKPollInterval,
uint32_t ui32TargetEndpoint, uint32_t ui32Flags)
{
uint32_t ui32Register;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
ASSERT(ui32NAKPollInterval <= MAX_NAK_LIMIT);
//
// Endpoint zero is configured differently than the other endpoints, so see
// if this is endpoint zero.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Set the NAK timeout.
//
HWREGB(ui32Base + USB_O_NAKLMT) = ui32NAKPollInterval;
//
// Set the transfer type information.
//
HWREGB(ui32Base + USB_O_TYPE0) =
((ui32Flags & USB_EP_SPEED_FULL) ? USB_TYPE0_SPEED_FULL :
USB_TYPE0_SPEED_LOW);
}
else
{
//
// Start with the target endpoint.
//
ui32Register = ui32TargetEndpoint;
//
// Set the speed for the device using this endpoint.
//
if(ui32Flags & USB_EP_SPEED_FULL)
{
ui32Register |= USB_TXTYPE1_SPEED_FULL;
}
else
{
ui32Register |= USB_TXTYPE1_SPEED_LOW;
}
//
// Set the protocol for the device using this endpoint.
//
switch(ui32Flags & USB_EP_MODE_MASK)
{
//
// The bulk protocol is being used.
//
case USB_EP_MODE_BULK:
{
ui32Register |= USB_TXTYPE1_PROTO_BULK;
break;
}
//
// The isochronous protocol is being used.
//
case USB_EP_MODE_ISOC:
{
ui32Register |= USB_TXTYPE1_PROTO_ISOC;
break;
}
//
// The interrupt protocol is being used.
//
case USB_EP_MODE_INT:
{
ui32Register |= USB_TXTYPE1_PROTO_INT;
break;
}
//
// The control protocol is being used.
//
case USB_EP_MODE_CTRL:
{
ui32Register |= USB_TXTYPE1_PROTO_CTRL;
break;
}
}
//
// See if the transmit or receive endpoint is being configured.
//
if(ui32Flags & USB_EP_HOST_OUT)
{
//
// Set the transfer type information.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXTYPE1) =
ui32Register;
//
// Set the NAK timeout or polling interval.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXINTERVAL1) =
ui32NAKPollInterval;
//
// Set the Maximum Payload per transaction.
//
HWREGH(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXMAXP1) =
ui32MaxPayload;
//
// Set the transmit control value to zero.
//
ui32Register = 0;
//
// Allow auto setting of TxPktRdy when max packet size has been
// loaded into the FIFO.
//
if(ui32Flags & USB_EP_AUTO_SET)
{
ui32Register |= USB_TXCSRH1_AUTOSET;
}
//
// Configure the DMA Mode.
//
if(ui32Flags & USB_EP_DMA_MODE_1)
{
ui32Register |= USB_TXCSRH1_DMAEN | USB_TXCSRH1_DMAMOD;
}
else if(ui32Flags & USB_EP_DMA_MODE_0)
{
ui32Register |= USB_TXCSRH1_DMAEN;
}
//
// Write out the transmit control value.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRH1) =
(uint8_t)ui32Register;
}
else
{
//
// Set the transfer type information.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXTYPE1) =
ui32Register;
//
// Set the NAK timeout or polling interval.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXINTERVAL1) =
ui32NAKPollInterval;
//
// Set the Maximum Payload per transaction.
//
HWREGH(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXMAXP1) =
ui32MaxPayload;
//
// Set the receive control value to zero.
//
ui32Register = 0;
//
// Allow auto clearing of RxPktRdy when packet of size max packet
// has been unloaded from the FIFO.
//
if(ui32Flags & USB_EP_AUTO_CLEAR)
{
ui32Register |= USB_RXCSRH1_AUTOCL;
}
//
// Allow auto generation of DMA requests.
//
if(ui32Flags & USB_EP_AUTO_REQUEST)
{
ui32Register |= USB_RXCSRH1_AUTORQ;
}
//
// Configure the DMA Mode.
//
if(ui32Flags & USB_EP_DMA_MODE_1)
{
ui32Register |= USB_RXCSRH1_DMAEN | USB_RXCSRH1_DMAMOD;
}
else if(ui32Flags & USB_EP_DMA_MODE_0)
{
ui32Register |= USB_RXCSRH1_DMAEN;
}
//
// Write out the receive control value.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRH1) =
(uint8_t)ui32Register;
}
}
}
//*****************************************************************************
//
//! Sets the configuration for an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32MaxPacketSize is the maximum packet size for this endpoint.
//! \param ui32Flags are used to configure other endpoint settings.
//!
//! This function sets the basic configuration for an endpoint in device mode.
//! Endpoint zero does not have a dynamic configuration, so this function
//! must not be called for endpoint zero. The \e ui32Flags parameter
//! determines some of the configuration while the other parameters provide the
//! rest.
//!
//! The \b USB_EP_MODE_ flags define what the type is for the given endpoint.
//!
//! - \b USB_EP_MODE_CTRL is a control endpoint.
//! - \b USB_EP_MODE_ISOC is an isochronous endpoint.
//! - \b USB_EP_MODE_BULK is a bulk endpoint.
//! - \b USB_EP_MODE_INT is an interrupt endpoint.
//!
//! The \b USB_EP_DMA_MODE_ flags determine the type of DMA access to the
//! endpoint data FIFOs. The choice of the DMA mode depends on how the DMA
//! controller is configured and how it is being used. See the ``Using USB
//! with the uDMA Controller'' section for more information on DMA
//! configuration.
//!
//! When configuring an IN endpoint, the \b USB_EP_AUTO_SET bit can be
//! specified to cause the automatic transmission of data on the USB bus as
//! soon as \e ui32MaxPacketSize bytes of data are written into the FIFO for
//! this endpoint. This option is commonly used with DMA as no interaction is
//! required to start the transmission of data.
//!
//! When configuring an OUT endpoint, the \b USB_EP_AUTO_REQUEST bit is
//! specified to trigger the request for more data once the FIFO has been
//! drained enough to receive \e ui32MaxPacketSize more bytes of data. Also
//! for OUT endpoints, the \b USB_EP_AUTO_CLEAR bit can be used to clear the
//! data packet ready flag automatically once the data has been read from the
//! FIFO. If this option is not used, this flag must be manually cleared via a
//! call to USBDevEndpointStatusClear(). Both of these settings can be used to
//! remove the need for extra calls when using the controller in DMA mode.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevEndpointConfigSet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32MaxPacketSize, uint32_t ui32Flags)
{
uint32_t ui32Register;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_1) || (ui32Endpoint == USB_EP_2) ||
(ui32Endpoint == USB_EP_3) || (ui32Endpoint == USB_EP_4) ||
(ui32Endpoint == USB_EP_5) || (ui32Endpoint == USB_EP_6) ||
(ui32Endpoint == USB_EP_7));
//
// Determine if a transmit or receive endpoint is being configured.
//
if(ui32Flags & USB_EP_DEV_IN)
{
//
// Set the maximum packet size.
//
HWREGH(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXMAXP1) =
ui32MaxPacketSize;
//
// The transmit control value is zero unless options are enabled.
//
ui32Register = 0;
//
// Allow auto setting of TxPktRdy when max packet size has been loaded
// into the FIFO.
//
if(ui32Flags & USB_EP_AUTO_SET)
{
ui32Register |= USB_TXCSRH1_AUTOSET;
}
//
// Configure the DMA mode.
//
if(ui32Flags & USB_EP_DMA_MODE_1)
{
ui32Register |= USB_TXCSRH1_DMAEN | USB_TXCSRH1_DMAMOD;
}
else if(ui32Flags & USB_EP_DMA_MODE_0)
{
ui32Register |= USB_TXCSRH1_DMAEN;
}
//
// Enable isochronous mode if requested.
//
if((ui32Flags & USB_EP_MODE_MASK) == USB_EP_MODE_ISOC)
{
ui32Register |= USB_TXCSRH1_ISO;
}
//
// Write the transmit control value.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRH1) =
(uint8_t)ui32Register;
//
// Reset the Data toggle to zero.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRL1) =
USB_TXCSRL1_CLRDT;
}
else
{
//
// Set the MaxPacketSize.
//
HWREGH(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXMAXP1) =
ui32MaxPacketSize;
//
// The receive control value is zero unless options are enabled.
//
ui32Register = 0;
//
// Allow auto clearing of RxPktRdy when packet of size max packet
// has been unloaded from the FIFO.
//
if(ui32Flags & USB_EP_AUTO_CLEAR)
{
ui32Register = USB_RXCSRH1_AUTOCL;
}
//
// Configure the DMA mode.
//
if(ui32Flags & USB_EP_DMA_MODE_1)
{
ui32Register |= USB_RXCSRH1_DMAEN | USB_RXCSRH1_DMAMOD;
}
else if(ui32Flags & USB_EP_DMA_MODE_0)
{
ui32Register |= USB_RXCSRH1_DMAEN;
}
//
// Enable isochronous mode if requested.
//
if((ui32Flags & USB_EP_MODE_MASK) == USB_EP_MODE_ISOC)
{
ui32Register |= USB_RXCSRH1_ISO;
}
//
// Write the receive control value.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRH1) =
(uint8_t)ui32Register;
//
// Reset the Data toggle to zero.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRL1) =
USB_RXCSRL1_CLRDT;
}
}
//*****************************************************************************
//
//! Gets the current configuration for an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param pui32MaxPacketSize is a pointer which is written with the maximum
//! packet size for this endpoint.
//! \param pui32Flags is a pointer which is written with the current endpoint
//! settings. On entry to the function, this pointer must contain either
//! \b USB_EP_DEV_IN or \b USB_EP_DEV_OUT to indicate whether the IN or OUT
//! endpoint is to be queried.
//!
//! This function returns the basic configuration for an endpoint in device
//! mode. The values returned in \e *pui32MaxPacketSize and \e *pui32Flags are
//! equivalent to the \e ui32MaxPacketSize and \e ui32Flags previously passed
//! to USBDevEndpointConfigSet() for this endpoint.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevEndpointConfigGet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t *pui32MaxPacketSize, uint32_t *pui32Flags)
{
uint32_t ui32Register;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT(pui32MaxPacketSize && pui32Flags);
ASSERT((ui32Endpoint == USB_EP_1) || (ui32Endpoint == USB_EP_2) ||
(ui32Endpoint == USB_EP_3) || (ui32Endpoint == USB_EP_4) ||
(ui32Endpoint == USB_EP_5) || (ui32Endpoint == USB_EP_6) ||
(ui32Endpoint == USB_EP_7));
//
// Determine if a transmit or receive endpoint is being queried.
//
if(*pui32Flags & USB_EP_DEV_IN)
{
//
// Clear the flags other than the direction bit.
//
*pui32Flags = USB_EP_DEV_IN;
//
// Get the maximum packet size.
//
*pui32MaxPacketSize = (uint32_t)HWREGH(ui32Base +
EP_OFFSET(ui32Endpoint) +
USB_O_TXMAXP1);
//
// Get the current transmit control register value.
//
ui32Register = (uint32_t)HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) +
USB_O_TXCSRH1);
//
// Are we allowing auto setting of TxPktRdy when max packet size has
// been loaded into the FIFO?
//
if(ui32Register & USB_TXCSRH1_AUTOSET)
{
*pui32Flags |= USB_EP_AUTO_SET;
}
//
// Get the DMA mode.
//
if(ui32Register & USB_TXCSRH1_DMAEN)
{
if(ui32Register & USB_TXCSRH1_DMAMOD)
{
*pui32Flags |= USB_EP_DMA_MODE_1;
}
else
{
*pui32Flags |= USB_EP_DMA_MODE_0;
}
}
//
// Are we in isochronous mode?
//
if(ui32Register & USB_TXCSRH1_ISO)
{
*pui32Flags |= USB_EP_MODE_ISOC;
}
else
{
//
// The hardware doesn't differentiate between bulk, interrupt
// and control mode for the endpoint so we just set something
// that isn't isochronous. This protocol ensures that anyone
// modifying the returned flags in preparation for a call to
// USBDevEndpointConfigSet do not see an unexpected mode change.
// If they decode the returned mode, however, they may be in for
// a surprise.
//
*pui32Flags |= USB_EP_MODE_BULK;
}
}
else
{
//
// Clear the flags other than the direction bit.
//
*pui32Flags = USB_EP_DEV_OUT;
//
// Get the MaxPacketSize.
//
*pui32MaxPacketSize = (uint32_t)HWREGH(ui32Base +
EP_OFFSET(ui32Endpoint) +
USB_O_RXMAXP1);
//
// Get the current receive control register value.
//
ui32Register = (uint32_t)HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) +
USB_O_RXCSRH1);
//
// Are we allowing auto clearing of RxPktRdy when packet of size max
// packet has been unloaded from the FIFO?
//
if(ui32Register & USB_RXCSRH1_AUTOCL)
{
*pui32Flags |= USB_EP_AUTO_CLEAR;
}
//
// Get the DMA mode.
//
if(ui32Register & USB_RXCSRH1_DMAEN)
{
if(ui32Register & USB_RXCSRH1_DMAMOD)
{
*pui32Flags |= USB_EP_DMA_MODE_1;
}
else
{
*pui32Flags |= USB_EP_DMA_MODE_0;
}
}
//
// Are we in isochronous mode?
//
if(ui32Register & USB_RXCSRH1_ISO)
{
*pui32Flags |= USB_EP_MODE_ISOC;
}
else
{
//
// The hardware doesn't differentiate between bulk, interrupt
// and control mode for the endpoint so we just set something
// that isn't isochronous. This protocol ensures that anyone
// modifying the returned flags in preparation for a call to
// USBDevEndpointConfigSet do not see an unexpected mode change.
// If they decode the returned mode, however, they may be in for
// a surprise.
//
*pui32Flags |= USB_EP_MODE_BULK;
}
}
}
//*****************************************************************************
//
//! Sets the FIFO configuration for an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32FIFOAddress is the starting address for the FIFO.
//! \param ui32FIFOSize is the size of the FIFO specified by one of the
//! USB_FIFO_SZ_ values.
//! \param ui32Flags specifies what information to set in the FIFO
//! configuration.
//!
//! This function configures the starting FIFO RAM address and size of the FIFO
//! for a given endpoint. Endpoint zero does not have a dynamically
//! configurable FIFO, so this function must not be called for endpoint zero.
//! The \e ui32FIFOSize parameter must be one of the values in the
//! \b USB_FIFO_SZ_ values.
//!
//! The \e ui32FIFOAddress value must be a multiple of 8 bytes and directly
//! indicates the starting address in the USB controller's FIFO RAM. For
//! example, a value of 64 indicates that the FIFO starts 64 bytes into
//! the USB controller's FIFO memory. The \e ui32Flags value specifies whether
//! the endpoint's OUT or IN FIFO must be configured. If in host mode, use
//! \b USB_EP_HOST_OUT or \b USB_EP_HOST_IN, and if in device mode, use
//! \b USB_EP_DEV_OUT or \b USB_EP_DEV_IN.
//!
//! \return None.
//
//*****************************************************************************
void
USBFIFOConfigSet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32FIFOAddress, uint32_t ui32FIFOSize,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_1) || (ui32Endpoint == USB_EP_2) ||
(ui32Endpoint == USB_EP_3) || (ui32Endpoint == USB_EP_4) ||
(ui32Endpoint == USB_EP_5) || (ui32Endpoint == USB_EP_6) ||
(ui32Endpoint == USB_EP_7));
//
// See if the transmit or receive FIFO is being configured.
//
if(ui32Flags & (USB_EP_HOST_OUT | USB_EP_DEV_IN))
{
//
// Set the transmit FIFO location and size for this endpoint.
//
_USBIndexWrite(ui32Base, ui32Endpoint >> 4, USB_O_TXFIFOSZ,
ui32FIFOSize, 1);
_USBIndexWrite(ui32Base, ui32Endpoint >> 4, USB_O_TXFIFOADD,
ui32FIFOAddress >> 3, 2);
}
else
{
//
// Set the receive FIFO location and size for this endpoint.
//
_USBIndexWrite(ui32Base, ui32Endpoint >> 4, USB_O_RXFIFOSZ,
ui32FIFOSize, 1);
_USBIndexWrite(ui32Base, ui32Endpoint >> 4, USB_O_RXFIFOADD,
ui32FIFOAddress >> 3, 2);
}
}
//*****************************************************************************
//
//! Returns the FIFO configuration for an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param pui32FIFOAddress is the starting address for the FIFO.
//! \param pui32FIFOSize is the size of the FIFO as specified by one of the
//! USB_FIFO_SZ_ values.
//! \param ui32Flags specifies what information to retrieve from the FIFO
//! configuration.
//!
//! This function returns the starting address and size of the FIFO for a
//! given endpoint. Endpoint zero does not have a dynamically configurable
//! FIFO, so this function must not be called for endpoint zero. The
//! \e ui32Flags parameter specifies whether the endpoint's OUT or IN FIFO must
//! be read. If in host mode, the \e ui32Flags parameter must be
//! \b USB_EP_HOST_OUT or \b USB_EP_HOST_IN, and if in device mode, the
//! \e ui32Flags parameter must be either \b USB_EP_DEV_OUT or
//! \b USB_EP_DEV_IN.
//!
//! \return None.
//
//*****************************************************************************
void
USBFIFOConfigGet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t *pui32FIFOAddress, uint32_t *pui32FIFOSize,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_1) || (ui32Endpoint == USB_EP_2) ||
(ui32Endpoint == USB_EP_3) || (ui32Endpoint == USB_EP_4) ||
(ui32Endpoint == USB_EP_5) || (ui32Endpoint == USB_EP_6) ||
(ui32Endpoint == USB_EP_7));
//
// See if the transmit or receive FIFO is being configured.
//
if(ui32Flags & (USB_EP_HOST_OUT | USB_EP_DEV_IN))
{
//
// Get the transmit FIFO location and size for this endpoint.
//
*pui32FIFOAddress = (_USBIndexRead(ui32Base, ui32Endpoint >> 4,
(uint32_t)USB_O_TXFIFOADD,
2)) << 3;
*pui32FIFOSize = _USBIndexRead(ui32Base, ui32Endpoint >> 4,
(uint32_t)USB_O_TXFIFOSZ, 1);
}
else
{
//
// Get the receive FIFO location and size for this endpoint.
//
*pui32FIFOAddress = (_USBIndexRead(ui32Base, ui32Endpoint >> 4,
(uint32_t)USB_O_RXFIFOADD,
2)) << 3;
*pui32FIFOSize = _USBIndexRead(ui32Base, ui32Endpoint >> 4,
(uint32_t)USB_O_RXFIFOSZ, 1);
}
}
//*****************************************************************************
//
//! Configure the DMA settings for an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Config specifies the configuration options for an endpoint.
//!
//! This function configures the DMA settings for a given endpoint without
//! changing other options that may already be configured. In order for the
//! DMA transfer to be enabled, the USBEndpointDMAEnable() function must be
//! called before starting the DMA transfer. The configuration
//! options are passed in the \e ui32Config parameter and can have the values
//! described below.
//!
//! One of the following values to specify direction:
//! - \b USB_EP_HOST_OUT or \b USB_EP_DEV_IN - This setting is used with
//! DMA transfers from memory to the USB controller.
//! - \b USB_EP_HOST_IN or \b USB_EP_DEV_OUT - This setting is used with
//! DMA transfers from the USB controller to memory.
//!
//! One of the following values:
//! - \b USB_EP_DMA_MODE_0(default) - This setting is typically used for
//! transfers that do not span multiple packets or when interrupts are
//! required for each packet.
//! - \b USB_EP_DMA_MODE_1 - This setting is typically used for
//! transfers that span multiple packets and do not require interrupts
//! between packets.
//!
//! Values only used with \b USB_EP_HOST_OUT or \b USB_EP_DEV_IN:
//! - \b USB_EP_AUTO_SET - This setting is used to allow transmit DMA transfers
//! to automatically be sent when a full packet is loaded into a FIFO.
//! This is needed with \b USB_EP_DMA_MODE_1 to ensure that packets go
//! out when the FIFO becomes full and the DMA has more data to send.
//!
//! Values only used with \b USB_EP_HOST_IN or \b USB_EP_DEV_OUT:
//! - \b USB_EP_AUTO_CLEAR - This setting is used to allow receive DMA
//! transfers to automatically be acknowledged as they are received. This is
//! needed with \b USB_EP_DMA_MODE_1 to ensure that packets continue to
//! be received and acknowledged when the FIFO is emptied by the DMA
//! transfer.
//!
//! Values only used with \b USB_EP_HOST_IN:
//! - \b USB_EP_AUTO_REQUEST - This setting is used to allow receive DMA
//! transfers to automatically request a new IN transaction when the
//! previous transfer has emptied the FIFO. This is typically used in
//! conjunction with \b USB_EP_AUTO_CLEAR so that receive DMA transfers
//! can continue without interrupting the main processor.
//!
//! \b Example: Set endpoint 1 receive endpoint to automatically acknowledge
//! request and automatically generate a new IN request in host mode.
//!
//! \verbatim
//! //
//! // Configure endpoint 1 for receiving multiple packets using DMA.
//! //
//! USBEndpointDMAConfigSet(USB0_BASE, USB_EP_1, USB_EP_HOST_IN |
//! USB_EP_DMA_MODE_1 |
//! USB_EP_AUTO_CLEAR |
//! USB_EP_AUTO_REQUEST);
//! \endverbatim
//!
//! \b Example: Set endpoint 2 transmit endpoint to automatically send each
//! packet in host mode when spanning multiple packets.
//!
//! \verbatim
//! //
//! // Configure endpoint 1 for transmitting multiple packets using DMA.
//! //
//! USBEndpointDMAConfigSet(USB0_BASE, USB_EP_2, USB_EP_HOST_OUT |
//! USB_EP_DMA_MODE_1 |
//! USB_EP_AUTO_SET);
//! \endverbatim
//!
//! \return None.
//
//*****************************************************************************
void
USBEndpointDMAConfigSet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Config)
{
uint32_t ui32NewConfig;
if(ui32Config & USB_EP_HOST_OUT)
{
//
// Clear mode and DMA enable.
//
ui32NewConfig =
(HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRH1) &
~(USB_TXCSRH1_DMAMOD | USB_TXCSRH1_AUTOSET));
if(ui32Config & USB_EP_DMA_MODE_1)
{
ui32NewConfig |= USB_TXCSRH1_DMAMOD;
}
if(ui32Config & USB_EP_AUTO_SET)
{
ui32NewConfig |= USB_TXCSRH1_AUTOSET;
}
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRH1) =
ui32NewConfig;
}
else
{
ui32NewConfig =
(HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRH1) &
~(USB_RXCSRH1_AUTORQ | USB_RXCSRH1_AUTOCL | USB_RXCSRH1_DMAMOD));
if(ui32Config & USB_EP_DMA_MODE_1)
{
ui32NewConfig |= USB_RXCSRH1_DMAMOD;
}
if(ui32Config & USB_EP_AUTO_CLEAR)
{
ui32NewConfig |= USB_RXCSRH1_AUTOCL;
}
if(ui32Config & USB_EP_AUTO_REQUEST)
{
ui32NewConfig |= USB_RXCSRH1_AUTORQ;
}
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRH1) =
ui32NewConfig;
}
}
//*****************************************************************************
//
//! Enable DMA on a given endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags specifies which direction and what mode to use when
//! enabling DMA.
//!
//! This function enables DMA on a given endpoint and configures the mode
//! according to the values in the \e ui32Flags parameter. The \e ui32Flags
//! parameter must have \b USB_EP_DEV_IN or \b USB_EP_DEV_OUT set. Once this
//! function is called the only DMA or error interrupts are generated by the
//! USB controller.
//!
//! \note If this function is called when an endpoint is configured in DMA
//! mode 0 the USB controller does not generate an interrupt.
//!
//! \return None.
//
//*****************************************************************************
void
USBEndpointDMAEnable(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// See if the transmit DMA is being enabled.
//
if(ui32Flags & USB_EP_DEV_IN)
{
//
// Enable DMA on the transmit endpoint.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRH1) |=
USB_TXCSRH1_DMAEN;
}
else
{
//
// Enable DMA on the receive endpoint.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRH1) |=
USB_RXCSRH1_DMAEN;
}
}
//*****************************************************************************
//
//! Disable DMA on a given endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags specifies which direction to disable.
//!
//! This function disables DMA on a given endpoint to allow non-DMA USB
//! transactions to generate interrupts normally. The \e ui32Flags parameter
//! must be \b USB_EP_DEV_IN or \b USB_EP_DEV_OUT; all other bits are ignored.
//!
//! \return None.
//
//*****************************************************************************
void
USBEndpointDMADisable(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Flags)
{
//
// If this was a request to disable DMA on the IN portion of the endpoint
// then handle it.
//
if(ui32Flags & USB_EP_DEV_IN)
{
//
// Just disable DMA leave the mode setting.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_TXCSRH1) &=
~USB_TXCSRH1_DMAEN;
}
else
{
//
// Just disable DMA leave the mode setting.
//
HWREGB(ui32Base + EP_OFFSET(ui32Endpoint) + USB_O_RXCSRH1) &=
~USB_RXCSRH1_DMAEN;
}
}
//*****************************************************************************
//
//! Determine the number of bytes of data available in a given endpoint's FIFO.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//!
//! This function returns the number of bytes of data currently available in
//! the FIFO for the given receive (OUT) endpoint. It may be used prior to
//! calling USBEndpointDataGet() to determine the size of buffer required to
//! hold the newly-received packet.
//!
//! \return This call returns the number of bytes available in a given endpoint
//! FIFO.
//
//*****************************************************************************
uint32_t
USBEndpointDataAvail(uint32_t ui32Base, uint32_t ui32Endpoint)
{
uint32_t ui32Register;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Get the address of the receive status register to use, based on the
// endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
ui32Register = USB_O_CSRL0;
}
else
{
ui32Register = USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint);
}
//
// Is there a packet ready in the FIFO?
//
if((HWREGH(ui32Base + ui32Register) & USB_CSRL0_RXRDY) == 0)
{
return(0);
}
//
// Return the byte count in the FIFO.
//
return(HWREGH(ui32Base + USB_O_COUNT0 + ui32Endpoint));
}
//*****************************************************************************
//
//! Retrieves data from the given endpoint's FIFO.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param pui8Data is a pointer to the data area used to return the data from
//! the FIFO.
//! \param pui32Size is initially the size of the buffer passed into this call
//! via the \e pui8Data parameter. It is set to the amount of data returned in
//! the buffer.
//!
//! This function returns the data from the FIFO for the given endpoint.
//! The \e pui32Size parameter indicates the size of the buffer passed in
//! the \e pui32Data parameter. The data in the \e pui32Size parameter is
//! changed to match the amount of data returned in the \e pui8Data parameter.
//! If a zero-byte packet is received, this call does not return an error but
//! instead just returns a zero in the \e pui32Size parameter. The only error
//! case occurs when there is no data packet available.
//!
//! \return This call returns 0, or -1 if no packet was received.
//
//*****************************************************************************
int32_t
USBEndpointDataGet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint8_t *pui8Data, uint32_t *pui32Size)
{
uint32_t ui32Register, ui32ByteCount, ui32FIFO;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Get the address of the receive status register to use, based on the
// endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
ui32Register = USB_O_CSRL0;
}
else
{
ui32Register = USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint);
}
//
// Don't allow reading of data if the RxPktRdy bit is not set.
//
if((HWREGH(ui32Base + ui32Register) & USB_CSRL0_RXRDY) == 0)
{
//
// Can't read the data because none is available.
//
*pui32Size = 0;
//
// Return a failure since there is no data to read.
//
return(-1);
}
//
// Get the byte count in the FIFO.
//
ui32ByteCount = HWREGH(ui32Base + USB_O_COUNT0 + ui32Endpoint);
//
// Determine how many bytes are copied.
//
ui32ByteCount = (ui32ByteCount < *pui32Size) ? ui32ByteCount : *pui32Size;
//
// Return the number of bytes we are going to read.
//
*pui32Size = ui32ByteCount;
//
// Calculate the FIFO address.
//
ui32FIFO = ui32Base + USB_O_FIFO0 + (ui32Endpoint >> 2);
//
// Read the data out of the FIFO.
//
for(; ui32ByteCount > 0; ui32ByteCount--)
{
//
// Read a byte at a time from the FIFO.
//
*pui8Data++ = HWREGB(ui32FIFO);
}
//
// Success.
//
return(0);
}
//*****************************************************************************
//
//! Acknowledge that data was read from the given endpoint's FIFO in device
//! mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param bIsLastPacket indicates if this packet is the last one.
//!
//! This function acknowledges that the data was read from the endpoint's FIFO.
//! The \e bIsLastPacket parameter is set to a \b true value if this is the
//! last in a series of data packets on endpoint zero. The \e bIsLastPacket
//! parameter is not used for endpoints other than endpoint zero. This call
//! can be used if processing is required between reading the data and
//! acknowledging that the data has been read.
//!
//! \note This function must only be called in device mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevEndpointDataAck(uint32_t ui32Base, uint32_t ui32Endpoint,
bool bIsLastPacket)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Determine which endpoint is being acked.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Clear RxPktRdy, and optionally DataEnd, on endpoint zero.
//
HWREGB(ui32Base + USB_O_CSRL0) =
USB_CSRL0_RXRDYC | (bIsLastPacket ? USB_CSRL0_DATAEND : 0);
}
else
{
//
// Clear RxPktRdy on all other endpoints.
//
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~(USB_RXCSRL1_RXRDY);
}
}
//*****************************************************************************
//
//! Acknowledge that data was read from the given endpoint's FIFO in host
//! mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//!
//! This function acknowledges that the data was read from the endpoint's FIFO.
//! This call is used if processing is required between reading the data and
//! acknowledging that the data has been read.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostEndpointDataAck(uint32_t ui32Base, uint32_t ui32Endpoint)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Clear RxPktRdy.
//
if(ui32Endpoint == USB_EP_0)
{
HWREGB(ui32Base + USB_O_CSRL0) &= ~USB_CSRL0_RXRDY;
}
else
{
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) &=
~(USB_RXCSRL1_RXRDY);
}
}
//*****************************************************************************
//
//! Puts data into the given endpoint's FIFO.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param pui8Data is a pointer to the data area used as the source for the
//! data to put into the FIFO.
//! \param ui32Size is the amount of data to put into the FIFO.
//!
//! This function puts the data from the \e pui8Data parameter into the FIFO
//! for this endpoint. If a packet is already pending for transmission, then
//! this call does not put any of the data into the FIFO and returns -1. Care
//! must be taken to not write more data than can fit into the FIFO
//! allocated by the call to USBFIFOConfigSet().
//!
//! \return This call returns 0 on success, or -1 to indicate that the FIFO
//! is in use and cannot be written.
//
//*****************************************************************************
int32_t
USBEndpointDataPut(uint32_t ui32Base, uint32_t ui32Endpoint,
uint8_t *pui8Data, uint32_t ui32Size)
{
uint32_t ui32FIFO;
uint8_t ui8TxPktRdy;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Get the bit position of TxPktRdy based on the endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
ui8TxPktRdy = USB_CSRL0_TXRDY;
}
else
{
ui8TxPktRdy = USB_TXCSRL1_TXRDY;
}
//
// Don't allow transmit of data if the TxPktRdy bit is already set.
//
if(HWREGB(ui32Base + USB_O_CSRL0 + ui32Endpoint) & ui8TxPktRdy)
{
return(-1);
}
//
// Calculate the FIFO address.
//
ui32FIFO = ui32Base + USB_O_FIFO0 + (ui32Endpoint >> 2);
//
// Write the data to the FIFO.
//
for(; ui32Size > 0; ui32Size--)
{
HWREGB(ui32FIFO) = *pui8Data++;
}
//
// Success.
//
return(0);
}
//*****************************************************************************
//
//! Starts the transfer of data from an endpoint's FIFO.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32TransType is set to indicate what type of data is being sent.
//!
//! This function starts the transfer of data from the FIFO for a given
//! endpoint. This function is called if the \b USB_EP_AUTO_SET bit was
//! not enabled for the endpoint. Setting the \e ui32TransType parameter
//! allows the appropriate signaling on the USB bus for the type of transaction
//! being requested. The \e ui32TransType parameter must be one of the
//! following:
//!
//! - \b USB_TRANS_OUT for OUT transaction on any endpoint in host mode.
//! - \b USB_TRANS_IN for IN transaction on any endpoint in device mode.
//! - \b USB_TRANS_IN_LAST for the last IN transaction on endpoint zero in a
//! sequence of IN transactions.
//! - \b USB_TRANS_SETUP for setup transactions on endpoint zero.
//! - \b USB_TRANS_STATUS for status results on endpoint zero.
//!
//! \return This call returns 0 on success, or -1 if a transmission is already
//! in progress.
//
//*****************************************************************************
int32_t
USBEndpointDataSend(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32TransType)
{
uint32_t ui32TxPktRdy;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Get the bit position of TxPktRdy based on the endpoint.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Don't allow transmit of data if the TxPktRdy bit is already set.
//
if(HWREGB(ui32Base + USB_O_CSRL0) & USB_CSRL0_TXRDY)
{
return(-1);
}
ui32TxPktRdy = ui32TransType & 0xff;
}
else
{
//
// Don't allow transmit of data if the TxPktRdy bit is already set.
//
if(HWREGB(ui32Base + USB_O_CSRL0 + ui32Endpoint) & USB_TXCSRL1_TXRDY)
{
return(-1);
}
ui32TxPktRdy = (ui32TransType >> 8) & 0xff;
}
//
// Set TxPktRdy in order to send the data.
//
HWREGB(ui32Base + USB_O_CSRL0 + ui32Endpoint) = ui32TxPktRdy;
//
// Success.
//
return(0);
}
//*****************************************************************************
//
//! Forces a flush of an endpoint's FIFO.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags specifies if the IN or OUT endpoint is accessed.
//!
//! This function forces the USB controller to flush out the data in the FIFO.
//! The function can be called with either host or device controllers and
//! requires the \e ui32Flags parameter be one of \b USB_EP_HOST_OUT,
//! \b USB_EP_HOST_IN, \b USB_EP_DEV_OUT, or \b USB_EP_DEV_IN.
//!
//! \return None.
//
//*****************************************************************************
void
USBFIFOFlush(uint32_t ui32Base, uint32_t ui32Endpoint, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Endpoint zero has a different register set for FIFO flushing.
//
if(ui32Endpoint == USB_EP_0)
{
//
// Nothing in the FIFO if neither of these bits are set.
//
if((HWREGB(ui32Base + USB_O_CSRL0) &
(USB_CSRL0_RXRDY | USB_CSRL0_TXRDY)) != 0)
{
//
// Hit the Flush FIFO bit.
//
HWREGB(ui32Base + USB_O_CSRH0) = USB_CSRH0_FLUSH;
}
}
else
{
//
// Only reset the IN or OUT FIFO.
//
if(ui32Flags & (USB_EP_HOST_OUT | USB_EP_DEV_IN))
{
//
// Make sure the FIFO is not empty.
//
if(HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) &
USB_TXCSRL1_TXRDY)
{
//
// Hit the Flush FIFO bit.
//
HWREGB(ui32Base + USB_O_TXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_TXCSRL1_FLUSH;
}
}
else
{
//
// Make sure that the FIFO is not empty.
//
if(HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) &
USB_RXCSRL1_RXRDY)
{
//
// Hit the Flush FIFO bit.
//
HWREGB(ui32Base + USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint)) |=
USB_RXCSRL1_FLUSH;
}
}
}
}
//*****************************************************************************
//
//! Schedules a request for an IN transaction on an endpoint in host mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//!
//! This function schedules a request for an IN transaction. When the USB
//! device being communicated with responds with the data, the data can be
//! retrieved by calling USBEndpointDataGet() or via a DMA transfer.
//!
//! \note This function must only be called in host mode and only for IN
//! endpoints.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostRequestIN(uint32_t ui32Base, uint32_t ui32Endpoint)
{
uint32_t ui32Register;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Endpoint zero uses a different offset than the other endpoints.
//
if(ui32Endpoint == USB_EP_0)
{
ui32Register = USB_O_CSRL0;
}
else
{
ui32Register = USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint);
}
//
// Set the request for an IN transaction.
//
HWREGB(ui32Base + ui32Register) = USB_RXCSRL1_REQPKT;
}
//*****************************************************************************
//
//! Clears a scheduled IN transaction for an endpoint in host mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//!
//! This function clears a previously scheduled IN transaction if it is still
//! pending. This function is used to safely disable any scheduled IN
//! transactions if the endpoint specified by \e ui32Endpoint is reconfigured
//! for communications with other devices.
//!
//! \note This function must only be called in host mode and only for IN
//! endpoints.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostRequestINClear(uint32_t ui32Base, uint32_t ui32Endpoint)
{
uint32_t ui32Register;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// Endpoint zero uses a different offset than the other endpoints.
//
if(ui32Endpoint == USB_EP_0)
{
ui32Register = USB_O_CSRL0;
}
else
{
ui32Register = USB_O_RXCSRL1 + EP_OFFSET(ui32Endpoint);
}
//
// Clear the request for an IN transaction.
//
HWREGB(ui32Base + ui32Register) &= ~USB_RXCSRL1_REQPKT;
}
//*****************************************************************************
//
//! Issues a request for a status IN transaction on endpoint zero.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function is used to cause a request for a status IN transaction from
//! a device on endpoint zero. This function can only be used with endpoint
//! zero as that is the only control endpoint that supports this ability. This
//! function is used to complete the last phase of a control transaction to a
//! device and an interrupt is signaled when the status packet has been
//! received.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostRequestStatus(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Set the request for a status IN transaction.
//
HWREGB(ui32Base + USB_O_CSRL0) = USB_CSRL0_REQPKT | USB_CSRL0_STATUS;
}
//*****************************************************************************
//
//! Sets the functional address for the device that is connected to an
//! endpoint in host mode.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Addr is the functional address for the controller to use for
//! this endpoint.
//! \param ui32Flags determines if this is an IN or an OUT endpoint.
//!
//! This function configures the functional address for a device that is using
//! this endpoint for communication. This \e ui32Addr parameter is the address
//! of the target device that this endpoint is communicating with. The
//! \e ui32Flags parameter indicates if the IN or OUT endpoint is set.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostAddrSet(uint32_t ui32Base, uint32_t ui32Endpoint, uint32_t ui32Addr,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// See if the transmit or receive address is set.
//
if(ui32Flags & USB_EP_HOST_OUT)
{
//
// Set the transmit address.
//
HWREGB(ui32Base + USB_O_TXFUNCADDR0 + (ui32Endpoint >> 1)) = ui32Addr;
}
else
{
//
// Set the receive address.
//
HWREGB(ui32Base + USB_O_TXFUNCADDR0 + 4 + (ui32Endpoint >> 1)) =
ui32Addr;
}
}
//*****************************************************************************
//
//! Gets the current functional device address for an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags determines if this is an IN or an OUT endpoint.
//!
//! This function returns the current functional address that an endpoint is
//! using to communicate with a device. The \e ui32Flags parameter determines
//! if the IN or OUT endpoint's device address is returned.
//!
//! \note This function must only be called in host mode.
//!
//! \return Returns the current function address being used by an endpoint.
//
//*****************************************************************************
uint32_t
USBHostAddrGet(uint32_t ui32Base, uint32_t ui32Endpoint, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// See if the transmit or receive address is returned.
//
if(ui32Flags & USB_EP_HOST_OUT)
{
//
// Return this endpoint's transmit address.
//
return(HWREGB(ui32Base + USB_O_TXFUNCADDR0 + (ui32Endpoint >> 1)));
}
else
{
//
// Return this endpoint's receive address.
//
return(HWREGB(ui32Base + USB_O_TXFUNCADDR0 + 4 + (ui32Endpoint >> 1)));
}
}
//*****************************************************************************
//
//! Sets the hub address for the device that is connected to an endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Addr is the hub address and port for the device using this
//! endpoint. The hub address must be defined in bits 0 through 6 with the
//! port number in bits 8 through 14.
//! \param ui32Flags determines if this is an IN or an OUT endpoint.
//!
//! This function configures the hub address for a device that is using this
//! endpoint for communication. The \e ui32Flags parameter determines if the
//! device address for the IN or the OUT endpoint is configured by this call
//! and sets the speed of the downstream device. Valid values are one of
//! \b USB_EP_HOST_OUT or \b USB_EP_HOST_IN optionally ORed with
//! \b USB_EP_SPEED_LOW.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostHubAddrSet(uint32_t ui32Base, uint32_t ui32Endpoint, uint32_t ui32Addr,
uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// See if the hub transmit or receive address is being set.
//
if(ui32Flags & USB_EP_HOST_OUT)
{
//
// Set the hub transmit address and port number for this endpoint.
//
HWREGH(ui32Base + USB_O_TXHUBADDR0 + (ui32Endpoint >> 1)) = ui32Addr;
}
else
{
//
// Set the hub receive address and port number for this endpoint.
//
HWREGH(ui32Base + USB_O_TXHUBADDR0 + 4 + (ui32Endpoint >> 1)) =
ui32Addr;
}
//
// Set the speed of communication for endpoint 0. This configuration is
// done here because it changes on a transaction-by-transaction basis for
// EP0. For other endpoints, this is set in USBHostEndpointConfig().
//
if(ui32Endpoint == USB_EP_0)
{
if(ui32Flags & USB_EP_SPEED_FULL)
{
HWREGB(ui32Base + USB_O_TYPE0) = USB_TYPE0_SPEED_FULL;
}
else
{
HWREGB(ui32Base + USB_O_TYPE0) = USB_TYPE0_SPEED_LOW;
}
}
}
//*****************************************************************************
//
//! Gets the current device hub address for this endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint to access.
//! \param ui32Flags determines if this is an IN or an OUT endpoint.
//!
//! This function returns the current hub address that an endpoint is using
//! to communicate with a device. The \e ui32Flags parameter determines if the
//! device address for the IN or OUT endpoint is returned.
//!
//! \note This function must only be called in host mode.
//!
//! \return This function returns the current hub address being used by an
//! endpoint.
//
//*****************************************************************************
uint32_t
USBHostHubAddrGet(uint32_t ui32Base, uint32_t ui32Endpoint, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_0) || (ui32Endpoint == USB_EP_1) ||
(ui32Endpoint == USB_EP_2) || (ui32Endpoint == USB_EP_3) ||
(ui32Endpoint == USB_EP_4) || (ui32Endpoint == USB_EP_5) ||
(ui32Endpoint == USB_EP_6) || (ui32Endpoint == USB_EP_7));
//
// See if the hub transmit or receive address is returned.
//
if(ui32Flags & USB_EP_HOST_OUT)
{
//
// Return the hub transmit address for this endpoint.
//
return(HWREGB(ui32Base + USB_O_TXHUBADDR0 + (ui32Endpoint >> 1)));
}
else
{
//
// Return the hub receive address for this endpoint.
//
return(HWREGB(ui32Base + USB_O_TXHUBADDR0 + 4 + (ui32Endpoint >> 1)));
}
}
//*****************************************************************************
//
//! Sets the configuration for USB power fault.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Flags specifies the configuration of the power fault.
//!
//! This function controls how the USB controller uses its external power
//! control pins (USBnPFLT and USBnEPEN). The flags specify the power
//! fault level sensitivity, the power fault action, and the power enable level
//! and source.
//!
//! One of the following can be selected as the power fault level sensitivity:
//!
//! - \b USB_HOST_PWRFLT_LOW - An external power fault is indicated by the pin
//! being driven low.
//! - \b USB_HOST_PWRFLT_HIGH - An external power fault is indicated by the pin
//! being driven high.
//!
//! One of the following can be selected as the power fault action:
//!
//! - \b USB_HOST_PWRFLT_EP_NONE - No automatic action when power fault
//! detected.
//! - \b USB_HOST_PWRFLT_EP_TRI - Automatically tri-state the USBnEPEN pin on a
//! power fault.
//! - \b USB_HOST_PWRFLT_EP_LOW - Automatically drive USBnEPEN pin low on a
//! power fault.
//! - \b USB_HOST_PWRFLT_EP_HIGH - Automatically drive USBnEPEN pin high on a
//! power fault.
//!
//! One of the following can be selected as the power enable level and source:
//!
//! - \b USB_HOST_PWREN_MAN_LOW - USBnEPEN is driven low by the USB controller
//! when USBHostPwrEnable() is called.
//! - \b USB_HOST_PWREN_MAN_HIGH - USBnEPEN is driven high by the USB
//! controller when USBHostPwrEnable() is
//! called.
//! - \b USB_HOST_PWREN_AUTOLOW - USBnEPEN is driven low by the USB controller
//! automatically if USBOTGSessionRequest() has
//! enabled a session.
//! - \b USB_HOST_PWREN_AUTOHIGH - USBnEPEN is driven high by the USB
//! controller automatically if
//! USBOTGSessionRequest() has enabled a
//! session.
//!
//! On devices that support the VBUS glitch filter, the
//! \b USB_HOST_PWREN_FILTER can be added to ignore small, short drops in VBUS
//! level caused by high power consumption. This feature is mainly used to
//! avoid causing VBUS errors caused by devices with high in-rush current.
//!
//! \note This function must only be called on microcontrollers that support
//! host mode or OTG operation.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostPwrConfig(uint32_t ui32Base, uint32_t ui32Flags)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Flags & ~(USB_HOST_PWREN_FILTER | USB_EPC_PFLTACT_M |
USB_EPC_PFLTAEN | USB_EPC_PFLTSEN_HIGH |
USB_EPC_EPEN_M)) == 0);
//
// If requested, enable VBUS droop detection on parts that support this
// feature.
//
HWREG(ui32Base + USB_O_VDC) = ui32Flags >> 16;
//
// Set the power fault configuration as specified. This configuration
// does not change whether fault detection is enabled or not.
//
HWREGH(ui32Base + USB_O_EPC) =
(ui32Flags | (HWREGH(ui32Base + USB_O_EPC) &
~(USB_EPC_PFLTACT_M | USB_EPC_PFLTAEN |
USB_EPC_PFLTSEN_HIGH | USB_EPC_EPEN_M)));
}
//*****************************************************************************
//
//! Enables power fault detection.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function enables power fault detection in the USB controller. If the
//! USBnPFLT pin is not in use, this function must not be used.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostPwrFaultEnable(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Enable power fault input.
//
HWREGH(ui32Base + USB_O_EPC) |= USB_EPC_PFLTEN;
}
//*****************************************************************************
//
//! Disables power fault detection.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function disables power fault detection in the USB controller.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostPwrFaultDisable(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Enable power fault input.
//
HWREGH(ui32Base + USB_O_EPC) &= ~USB_EPC_PFLTEN;
}
//*****************************************************************************
//
//! Enables the external power pin.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function enables the USBnEPEN signal, which enables an external power
//! supply in host mode operation.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostPwrEnable(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Enable the external power supply enable signal.
//
HWREGH(ui32Base + USB_O_EPC) |= USB_EPC_EPENDE;
}
//*****************************************************************************
//
//! Disables the external power pin.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function disables the USBnEPEN signal, which disables an external
//! power supply in host mode operation.
//!
//! \note This function must only be called in host mode.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostPwrDisable(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Disable the external power supply enable signal.
//
HWREGH(ui32Base + USB_O_EPC) &= ~USB_EPC_EPENDE;
}
//*****************************************************************************
//
//! Get the current frame number.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function returns the last frame number received.
//!
//! \return The last frame number received.
//
//*****************************************************************************
uint32_t
USBFrameNumberGet(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Return the most recent frame number.
//
return(HWREGH(ui32Base + USB_O_FRAME));
}
//*****************************************************************************
//
//! Starts or ends a session.
//!
//! \param ui32Base specifies the USB module base address.
//! \param bStart specifies if this call starts or ends a session.
//!
//! This function is used in OTG mode to start a session request or end a
//! session. If the \e bStart parameter is set to \b true, then this function
//! starts a session and if it is \b false it ends a session.
//!
//! \return None.
//
//*****************************************************************************
void
USBOTGSessionRequest(uint32_t ui32Base, bool bStart)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Start or end the session as directed.
//
if(bStart)
{
HWREGB(ui32Base + USB_O_DEVCTL) |= USB_DEVCTL_SESSION;
}
else
{
HWREGB(ui32Base + USB_O_DEVCTL) &= ~USB_DEVCTL_SESSION;
}
}
//*****************************************************************************
//
//! Returns the absolute FIFO address for a given endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint specifies which endpoint's FIFO address to return.
//!
//! This function returns the actual physical address of the FIFO. This
//! address is needed when the USB is going to be used with the uDMA
//! controller and the source or destination address must be set to the
//! physical FIFO address for a given endpoint.
//!
//! \return None.
//
//*****************************************************************************
uint32_t
USBFIFOAddrGet(uint32_t ui32Base, uint32_t ui32Endpoint)
{
//
// Return the FIFO address for this endpoint.
//
return(ui32Base + USB_O_FIFO0 + (ui32Endpoint >> 2));
}
//*****************************************************************************
//
//! Returns the current operating mode of the controller.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function returns the current operating mode on USB controllers with
//! OTG or Dual mode functionality.
//!
//! For OTG controllers:
//!
//! The function returns one of the following values on OTG controllers:
//! \b USB_OTG_MODE_ASIDE_HOST, \b USB_OTG_MODE_ASIDE_DEV,
//! \b USB_OTG_MODE_BSIDE_HOST, \b USB_OTG_MODE_BSIDE_DEV,
//! \b USB_OTG_MODE_NONE.
//!
//! \b USB_OTG_MODE_ASIDE_HOST indicates that the controller is in host mode
//! on the A-side of the cable.
//!
//! \b USB_OTG_MODE_ASIDE_DEV indicates that the controller is in device mode
//! on the A-side of the cable.
//!
//! \b USB_OTG_MODE_BSIDE_HOST indicates that the controller is in host mode
//! on the B-side of the cable.
//!
//! \b USB_OTG_MODE_BSIDE_DEV indicates that the controller is in device mode
//! on the B-side of the cable. If an OTG session request is started with no
//! cable in place, this mode is the default.
//!
//! \b USB_OTG_MODE_NONE indicates that the controller is not attempting to
//! determine its role in the system.
//!
//! For Dual Mode controllers:
//!
//! The function returns one of the following values:
//! \b USB_DUAL_MODE_HOST, \b USB_DUAL_MODE_DEVICE, or
//! \b USB_DUAL_MODE_NONE.
//!
//! \b USB_DUAL_MODE_HOST indicates that the controller is acting as a host.
//!
//! \b USB_DUAL_MODE_DEVICE indicates that the controller acting as a device.
//!
//! \b USB_DUAL_MODE_NONE indicates that the controller is not active as
//! either a host or device.
//!
//! \return Returns \b USB_OTG_MODE_ASIDE_HOST, \b USB_OTG_MODE_ASIDE_DEV,
//! \b USB_OTG_MODE_BSIDE_HOST, \b USB_OTG_MODE_BSIDE_DEV,
//! \b USB_OTG_MODE_NONE, \b USB_DUAL_MODE_HOST, \b USB_DUAL_MODE_DEVICE, or
//! \b USB_DUAL_MODE_NONE.
//
//*****************************************************************************
uint32_t
USBModeGet(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Checks the current mode in the USB_O_DEVCTL and returns the current
// mode.
//
// USB_OTG_MODE_ASIDE_HOST: USB_DEVCTL_HOST | USB_DEVCTL_SESSION
// USB_OTG_MODE_ASIDE_DEV: USB_DEVCTL_SESSION
// USB_OTG_MODE_BSIDE_HOST: USB_DEVCTL_DEV | USB_DEVCTL_SESSION |
// USB_DEVCTL_HOST
// USB_OTG_MODE_BSIDE_DEV: USB_DEVCTL_DEV | USB_DEVCTL_SESSION
// USB_OTG_MODE_NONE: USB_DEVCTL_DEV
//
return(HWREGB(ui32Base + USB_O_DEVCTL) &
(USB_DEVCTL_DEV | USB_DEVCTL_HOST | USB_DEVCTL_SESSION |
USB_DEVCTL_VBUS_M));
}
//*****************************************************************************
//
//! Sets the DMA channel to use for a given endpoint.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint specifies which endpoint's FIFO address to return.
//! \param ui32Channel specifies which DMA channel to use for which endpoint.
//!
//! This function is used to configure which DMA channel to use with a given
//! endpoint. Receive DMA channels can only be used with receive endpoints
//! and transmit DMA channels can only be used with transmit endpoints. As a
//! result, the 3 receive and 3 transmit DMA channels can be mapped to any
//! endpoint other than 0. The values that are passed into the
//! \e ui32Channel value are the UDMA_CHANNEL_USBEP* values defined in udma.h.
//!
//! \note This function only has an effect on microcontrollers that have the
//! ability to change the DMA channel for an endpoint. Calling this function
//! on other devices has no effect.
//!
//! \return None.
//!
//*****************************************************************************
void
USBEndpointDMAChannel(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Channel)
{
uint32_t ui32Mask;
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
ASSERT((ui32Endpoint == USB_EP_1) || (ui32Endpoint == USB_EP_2) ||
(ui32Endpoint == USB_EP_3) || (ui32Endpoint == USB_EP_4) ||
(ui32Endpoint == USB_EP_5) || (ui32Endpoint == USB_EP_6) ||
(ui32Endpoint == USB_EP_7));
// ASSERT(ui32Channel <= UDMA_CHANNEL_USBEP3TX);
//
// The input select mask must be shifted into the correct position
// based on the channel.
//
ui32Mask = (uint32_t)0xf << (ui32Channel * 4);
//
// Clear out the current selection for the channel.
//
ui32Mask = HWREG(ui32Base + USB_O_DMASEL) & (~ui32Mask);
//
// The input select is now shifted into the correct position based on the
// channel.
//
ui32Mask |= ((uint32_t)USBEPToIndex(ui32Endpoint)) << (ui32Channel * 4);
//
// Write the value out to the register.
//
HWREG(ui32Base + USB_O_DMASEL) = ui32Mask;
}
//*****************************************************************************
//
//! Change the mode of the USB controller to host.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function changes the mode of the USB controller to host mode.
//!
//! \note This function must only be called on microcontrollers that support
//! OTG operation and have the DEVMODOTG bit in the USBGPCS register.
//!
//! \return None.
//
//*****************************************************************************
void
USBHostMode(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Force mode in OTG parts that support forcing USB controller mode.
// This bit is not writable in USB controllers that do not support
// forcing the mode. Not setting the USB_GPCS_DEVMOD bit makes this a
// force of host mode.
//
HWREGB(ui32Base + USB_O_GPCS) = USB_GPCS_DEVMODOTG;
}
//*****************************************************************************
//
//! Change the mode of the USB controller to device.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function changes the mode of the USB controller to device mode.
//!
//! \note This function must only be called on microcontrollers that support
//! OTG operation and have the DEVMODOTG bit in the USBGPCS register.
//!
//! \return None.
//
//*****************************************************************************
void
USBDevMode(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Set the USB controller mode to device.
//
HWREGB(ui32Base + USB_O_GPCS) = USB_GPCS_DEVMODOTG | USB_GPCS_DEVMOD;
}
//*****************************************************************************
//
//! Change the mode of the USB controller to OTG.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function changes the mode of the USB controller to OTG mode. This
//! function is only valid on microcontrollers that have the OTG capabilities.
//!
//! \return None.
//
//*****************************************************************************
void
USBOTGMode(uint32_t ui32Base)
{
//
// Check the arguments.
//
ASSERT(ui32Base == USB0_BASE);
//
// Disable the override of the USB controller mode when running on an OTG
// device.
//
HWREGB(ui32Base + USB_O_GPCS) = 0;
}
//*****************************************************************************
//
//! Powers off the USB PHY.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function powers off the USB PHY, reducing the current consuption
//! of the device. While in the powered-off state, the USB controller is
//! unable to operate.
//!
//! \return None.
//
//*****************************************************************************
void
USBPHYPowerOff(uint32_t ui32Base)
{
//
// Set the PWRDNPHY bit in the PHY, putting it into its low power mode.
//
HWREGB(ui32Base + USB_O_POWER) |= USB_POWER_PWRDNPHY;
}
//*****************************************************************************
//
//! Powers on the USB PHY.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function powers on the USB PHY, enabling it return to normal
//! operation. By default, the PHY is powered on, so this function must
//! only be called if USBPHYPowerOff() has previously been called.
//!
//! \return None.
//
//*****************************************************************************
void
USBPHYPowerOn(uint32_t ui32Base)
{
//
// Clear the PWRDNPHY bit in the PHY, putting it into normal operating
// mode.
//
HWREGB(ui32Base + USB_O_POWER) &= ~USB_POWER_PWRDNPHY;
}
//*****************************************************************************
//
//! Sets the number of packets to request when transferring multiple bulk
//! packets.
//!
//! \param ui32Base specifies the USB module base address.
//! \param ui32Endpoint is the endpoint index to target for this write.
//! \param ui32Count is the number of packets to request.
//!
//! This function sets the number of consecutive bulk packets to request
//! when transferring multiple bulk packets with DMA.
//!
//! \note This feature is not available on all Tiva devices. Please
//! check the data sheet to determine if the USB controller has a DMA
//! controller or if it must use the uDMA controller for DMA transfers.
//!
//! \return None.
//
//*****************************************************************************
void
USBEndpointPacketCountSet(uint32_t ui32Base, uint32_t ui32Endpoint,
uint32_t ui32Count)
{
HWREG(ui32Base + USB_O_RQPKTCOUNT1 +
(0x4 * (USBEPToIndex(ui32Endpoint) - 1))) = ui32Count;
}
//*****************************************************************************
//
//! Returns the number of USB endpoint pairs on the device.
//!
//! \param ui32Base specifies the USB module base address.
//!
//! This function returns the number of endpoint pairs supported by the USB
//! controller corresponding to the passed base address. The value returned is
//! the number of IN or OUT endpoints available and does not include endpoint 0
//! (the control endpoint). For example, if 15 is returned, there are 15 IN
//! and 15 OUT endpoints available in addition to endpoint 0.
//!
//! \return Returns the number of IN or OUT endpoints available.
//
//*****************************************************************************
uint32_t
USBNumEndpointsGet(uint32_t ui32Base)
{
//
// Read the number of endpoints from the hardware. The number of TX and
// RX endpoints are always the same.
//
return(15);
}